Using computational fluid dynamics in combating erosion-corrosion

Computational fluid dynamics was used to search for the links between the observed pattern of attack seen in a bauxite refinery's heat exchanger headers and the hydrodynamics inside the header. Validation of the computational fluid dynamics results was done by comparing then with flow parameters measured in a 1:5 scale model of the first pass header in the laboratory. Computational fluid dynamics simulations were used to establish hydrodynamic similarity between the 1:5 scale and full scale models of the first pass header. It was found that the erosion-corrosion damage seen at the tubesheet of the first pass header was a consequence of increased levels of turbulence at the tubesheet caused by a rapidly turning flow. A prismatic flow corrections device introduced in the past helped in rectifying the problem at the tubesheet but exaggerated the erosion-corrosion problem at the first pass header shell. A number of alternative flow correction devices were tested using computational fluid dynamics. Axial ribbing in the first pass header and an inlet flow diffuser have shown the best performance and were recommended for implementation. Computational fluid dynamics simulations have revealed a smooth orderly low turbulence flow pattern in the second, third and fourth pass as well as the exit headers where no erosion-corrosion was seen in practice. This study has confirmed that near-wall turbulence intensity, which can be successfully predicted by using computational fluid dynamics, is a good hydrodynamic predictor of erosion-corrosion damage in complex geometries. (c) 2006 Published by Elsevier Ltd.

IDEOLOGIA DO TRABALHO NOS LIVROS DIDÁTICOS NA REPÚBLICA VELHA (1910-1930)

A partir de uma abordagem histórica, esta pesquisa apresenta como objetivo específico a análise da presença da ideologia do trabalho na sociedade brasileira e o modo como foi difundida nos livros didáticos no período de 1910 a 1930. O início do século XX foi marcado por grandes mudanças no Brasil. Nesta pesquisa, levaremos em conta apenas mudanças no Estado de São Paulo, que recebeu grande parte dos imigrantes europeus e concentrou muitas das indústrias brasileiras. Após a abolição da escravatura e da proclamação da República, o Brasil sofreu grandes transformações. O desenvolvimento da economia preocupava o Estado e a classe dominante, uma vez que não se encontravam indivíduos para a realização de trabalhos manuais. A sociedade ainda defendia a ideologia de que o trabalho manual era algo vergonhoso e de menos importância hierárquica. Foi então que os imigrantes foram contratados para exercer esse tipo de atividade. As péssimas condições de moradia, trabalho e participação política contribuíram para que os imigrantes reivindicassem seus direitos por meio de greves e manifestações. O governo não poderia permitir que os imigrantes com ideologias anarquistas disseminassem tais conceitos revolucionários e ideológicos no seio da massa operária e, consequentemente, na população. O Estado utilizou a educação para a inculcação de novas ideologias sobre a importância do trabalho, sustentando que o operário deveria cumprir suas obrigações dentro das indústrias sem questionar. Para tanto, era necessário que a escola adotasse algum tipo de material didático que difundisse ideologias a respeito do amor ao trabalho. Desde então, o livro didático foi utilizado como um forte transmissor destas ideologias: ele não foi usado como um simples material de apoio pedagógico, mas, sim, como um difusor de ideologias da classe dominante.

OS SENTIDOS DO FUTEBOL ESPETÁCULO PARA ESTUDANTES DE DISTINTAS CLASSES SOCIAIS

O presente estudo busca identificar em que medida o pertencimento de classe social interfere nos sentidos e perspectivas do jovem brasileiro frente ao futebol espetáculo, bem como compreender os mecanismos sociais que determinam a decisão de os sujeitos investirem na carreira profissional esportiva em detrimento da trajetória escolar longa. Começamos com uma abordagem sociológica, a análise crítica dos processos de difusão, massificação e profissionalização do futebol ocorridas no contexto da sociedade pós-industrial. Enfocamos a conflituosa mutação da modalidade, inicialmente elitizada com fins social-distintivos para esporte de massa ideal de ascensão social da classe popular , além da dependência com a mídia, das razões que levaram a caracterizar-se como produto da indústria cultural, culminando com a transformação do futebol em mercadoria submetida às leis e lógica da sociedade de consumo. Em seguida, entrelaçamos as relações de poder, aliança e concorrência dos agentes sociais que participam do complexo campo das práticas esportivas com os canais com que o público jovem estabelece contato com o esporte espetáculo. Neste aspecto, especial atenção foi dada à mídia, difusora da ideologia de uma sociedade capitalista aberta, que reforça a idéia do esporte como via de ascensão social para indivíduos de baixa renda, na mesma medida em que oculta em seu discurso as reais probabilidades de concretização do sucesso esportivo. A pesquisa de campo foi realizada em duas escolas do município de São Bernardo do Campo (SP), uma da rede pública estadual e outra da rede particular de ensino. Assim, constituímos dois grupos com alunos de distintas classes sociais, compostos por estudantes do 1º ano do Ensino Médio, sexo masculino, com 15 anos de idade e praticantes de futebol nas aulas de Educação Física. Metodologicamente, fizemos uso da observação participante e de entrevistas como instrumentos para a coleta de dados. Conjugadas aos objetivos do estudo, estruturamos a análise do material colhido em seis categorias, articulando questões sobre o prosseguimento nos estudos e o trabalho, as tendências para a pratica esportiva profissional, as representações sociais em torno do futebol, os usos e costumes no tempo livre e as expectativas da pratica esportiva implicadas pela herança cultural familiar. Como referencial teórico de análise, utilizamos de Pierre Bourdieu os conceitos de campo, habitus, estratégia, capital econômico, social e, principalmente, capital cultural, partindo da hipótese de que o nível cultural dos alunos e seus familiares interferem nos sentidos e formas de apropriação do esporte. Entre outras conclusões, obtivemos como resultado a configuração de uma trajetória esportiva profissional voltada para os alunos de baixa classe social, em oposição à trajetória escolar longa, estrategicamente adotada pelos alunos de classe social alta.(AU)

Using the e-Class Open Platform for e-Learning Support at the TEI of Larissa, Greece

In the current paper we firstly give a short introduction on e-learning platforms and review the case of the e-class open e-learning platform being used by the Greek tertiary education sector. Our analysis includes strategic selection issues and outcomes in general and operational and adoption issues in the case of the Technological Educational Institute (TEI) of Larissa, Greece. The methodology is being based on qualitative analysis of interviews with key actors using the platform, and statistical analysis of quantitative data related to adoption and usage in the relevant populations. The author has been a key actor in all stages and describes his insights as an early adopter, diffuser and innovative user. We try to explain the issues under consideration using existing past research outcomes and we also arrive to some conclusions and points for further research.

Otimização dos parâmetros de um modelo de bomba em sistemas de bombeio centrífugo submerso

One of several techniques applied to production processes oil is the artificial lift, using equipment in order to reduce the bottom hole pressure, providing a pressure differential, resulting in a flow increase. The choice of the artificial lift method depends on a detailed analysis of the some factors, such as initial costs of installation, maintenance, and the existing conditions in the producing field. The Electrical Submersible Pumping method (ESP) appears to be quite efficient when the objective is to produce high liquid flow rates in both onshore and offshore environments, in adverse conditions of temperature and in the presence of viscous fluids. By definition, ESP is a method of artificial lift in which a subsurface electric motor transforms electrical into mechanical energy to trigger a centrifugal pump of multiple stages, composed of a rotating impeller (rotor) and a stationary diffuser (stator). The pump converts the mechanical energy of the engine into kinetic energy in the form of velocity, which pushes the fluid to the surface. The objective of this work is to implement the optimization method of the flexible polyhedron, known as Modified Simplex Method (MSM) applied to the study of the influence of the modification of the input and output parameters of the centrifugal pump impeller in the channel of a system ESP. In the use of the optimization method by changing the angular parameters of the pump, the resultant data applied to the simulations allowed to obtain optimized values of the Head (lift height), lossless efficiency and the power with differentiated results.

La théorie sociale de la connaissance et la gestion du patrimoine documentaire à l’ère numérique

Les institutions de mémoire et de savoir (par exemple, les bibliothèques, les archives, les musées) font face à des défis importants dans leurs responsabilités d’assurer la pérennité du patrimoine documentaire à l’ère numérique. Citons la surabondance de l’information numérique, la possibilité de production, théoriquement illimitée, offerte aux individus comme aux groupes sociaux, les limites dans les capacités de stockage et de diffusion de l’information numérique qui sont à la disposition des institutions mandataires du patrimoine documentaire. De plus, il est apparu que les approches et les méthodes utilisées pour identifier, gérer, préserver et diffuser le patrimoine documentaire de la société canadienne dans un environnement analogique n’étaient transférables à un environnement numérique. Nous suggérons que la théorie sociale de la connaissance peut servir de base à une réflexion portant sur le développement d’une politique publique qui viserait à encadrer l’identification, la sélection, la gestion et la préservation du patrimoine documentaire d’une société à l'ère numérique. Nous définissons la problématique puis proposons des réponses à travers trois articles scientifiques. Les résultats indiquent que les connaissances et les pratiques professionnelles utilisées demeurent persistantes et limitent la formulation et l'application de nouveaux cadres théoriques, de politiques administratives et de techniques associés à l'identification et la sélection du patrimoine documentaire. Cette recherche propose un cadre conceptuel qui permet de développer des politiques publiques sur le patrimoine documentaire du Canada.

Assessment of turbulence model predictions for a centrifugal compressor simulation

Steady-state computational fluid dynamics (CFD) simulations are an essential tool in the design process of centrifugal compressors. Whilst global parameters, such as pressure ratio and efficiency, can be predicted with reasonable accuracy, the accurate prediction of detailed compressor flow fields is a much more significant challenge. Much of the inaccuracy is associated with the incorrect selection of turbulence model. The need for a quick turnaround in simulations during the design optimisation process, also demands that the turbulence model selected be robust and numerically stable with short simulation times.
In order to assess the accuracy of a number of turbulence model predictions, the current study used an exemplar open CFD test case, the centrifugal compressor ‘Radiver’, to compare the results of three eddy viscosity models and two Reynolds stress type models. The turbulence models investigated in this study were (i) Spalart-Allmaras (SA) model, (ii) the Shear Stress Transport (SST) model, (iii) a modification to the SST model denoted the SST-curvature correction (SST-CC), (iv) Reynolds stress model of Speziale, Sarkar and Gatski (RSM-SSG), and (v) the turbulence frequency formulated Reynolds stress model (RSM-ω). Each was found to be in good agreement with the experiments (below 2% discrepancy), with respect to total-to-total parameters at three different operating conditions. However, for the off-design conditions, local flow field differences were observed between the models, with the SA model showing particularly poor prediction of local flow structures. The SST-CC showed better prediction of curved rotating flows in the impeller. The RSM-ω was better for the wake and separated flow in the diffuser. The SST model showed reasonably stable, robust and time efficient capability to predict global and local flow features.

Recommandations pour une gestion durable des espaces verts en Bourgogne

Les espaces verts offrent de nombreux bienfaits aux populations urbaines, mais nécessitent souvent d’être gérés pour répondre aux besoins humains ainsi qu’aux contraintes du milieu. Dès les années 1950, cette gestion a été assurée par des pratiques horticoles intensives. Toutefois, à partir de 1970, les conséquences environnementales de ce mode de gestion chimique et mécanique ont poussé des gestionnaires à réviser leurs pratiques et s’engager dans la gestion durable. En France, l’adoption de la gestion durable par les collectivités est restée hétérogène et des pratiques dommageables pour l’environnement ont persisté jusqu’à aujourd’hui. Cependant, l’interdiction au 1er janvier 2017 pour les collectivités d’utiliser des produits phytosanitaires en zone non-agricole les poussent à réviser en profondeur leur gestion des espaces verts et se tourner vers des pratiques durables. Dans ce contexte, l’objectif de l’essai a été de dégager des recommandations pour la mise en œuvre effective d’une gestion durable des espaces verts en Bourgogne. Les enjeux identifiés dans cette gestion étaient la biodiversité, l’eau, le sol, la gestion et le paysage. Une enquête par questionnaire a permis de constater que les gestionnaires d’espaces verts étaient intéressés par la gestion durable et avaient déjà adopté des pratiques pour répondre aux enjeux de gestion identifiés. Toutefois, l’analyse des réponses a également révélé que le traitement des enjeux était inégal et qu’un important frein technique était rencontré. Ces résultats ont montré l’importance de diffuser des pratiques et d’apporter un support technique. Des études de cas auprès de gestionnaires bourguignons ont permis d’observer leurs pratiques. Une fois les pratiques analysées au regard des enjeux identifiés, elles ont permis de dégager des recommandations globales pour une gestion durable des espaces verts. Celles-ci sont au nombre de 45 et répondent à 15 problématiques rencontrées par les gestionnaires, telles que le désherbage, la fertilisation et le choix des végétaux. Finalement, afin de faciliter la diffusion des recommandations et leur application par les gestionnaires d’espaces verts, il a été décidé de les synthétiser sous forme de fiches. Celles-ci concernent les mêmes problématiques, mais sont organisées par type de formation végétale, afin de se rapprocher du travail de terrain des gestionnaires. L’aspect technique est également renforcé. Ces fiches synthétiques sont destinées à être diffusées aux communes par la Fredon Bourgogne en accompagnement des plans de gestion différenciée qu’elle développe.

Investigation expérimentale du décollement dans l’aspirateur d’une turbine bulbe

La présente thèse propose une étude expérimentale du décollement dans le diffuseur d’un modèle de turbine hydroélectrique bulbe. Le décollement se produit quand la turbine est opérée à forte charge et il réduit la section effective de récupération du diffuseur. La diminution de la performance du diffuseur à forte charge engendre une baisse brusque de l’efficacité de la turbine et de la puissance extraite. Le modèle réduit de bulbe est fidèle aux machines modernes avec un diffuseur particulièrement divergent. Les performances de la turbine sont mesurées sur une large gamme de points d’opération pour déterminer les conditions les plus intéressantes pour l’étude du décollement et pour étudier la distribution paramétrique de ce phénomène. La pression est mesurée le long de l’aspirateur par des capteurs dynamiques affleurants alors que les champs de vitesse dans la zone de décollement sont mesurés avec une méthode PIV à deux composantes. Les observations à la paroi sont pour leur part faites à l’aide de brins de laine. Pour un débit suffisant, le gradient de pression adverse induit par la géométrie du diffuseur affaiblit suffisamment la couche limite, entraînant ainsi l’éjection de fluide de la paroi le long d’une large enveloppe tridimensionelle. Le décollement instationnaire tridimensionnel se situe dans la même zone du diffuseur indépendamment du point d’opération. L’augmentation du débit provoque à la fois une extension de la zone de décollement et une augmentation de l’occurrence de ses manifestations. La position et la forme du front de décollement fluctue significativement sans périodicité. L’analyse topologique et celle des tourbillons des champs de vitesse instantanés montrent une topologie du front de décollement complexe qui diffère beaucoup d’une réalisation à l’autre. Bien que l’écoulement soit turbulent, les tourbillons associés aux foyers du front sont clairement plus gros et plus intenses que ceux de la turbulence. Cela suggère que le mécanisme d’enroulement menant aux tourbillons du décollement est clairement distinct des mécanismes de la turbulence.

Simulação numérica do escoamento monofásico em uma bomba centrífuga radial

Centrifugal pumps are vastly used in many industrial applications. Knowledge of how these components behave in several circumstances is crucial for the development of more efficient and, therefore, less expensive pumping installations. The combination of multiple impellers, vaned diffusers and a volute might introduce several complex flow characteristics that largely deviate from regular inviscid pump flow theory. Computational Fluid Dynamics can be very helpful to extract information about which physical phenomena are involved in such flows. In this sense, this work performs a numerical study of the flow in a two-stage centrifugal pump (Imbil ITAP 65-330/2) with a vaned diffuser and a volute. The flow in the pump is modeled using the software Ansys CFX, by means of a multi-block, transient rotor-stator technique, with structured grids for all pump parts. The simulations were performed using water and a mixture of water and glycerin as work fluids. Several viscosities were considered, in a range between 87 and 720 cP. Comparisons between experimental data obtained by Amaral (2007) and numerical head curves showed a good agreement, with an average deviation of 6.8% for water. The behavior of velocity, pressure and turbulence kinetic energy fields was evaluated for several operational conditions. In general, the results obtained by this work achieved the proposed goals and are a significant contribution to the understanding of the flow studied.

Americanismo e fordismo nos boletins da comissão brasileiro-americana de educação industrial

This text thematizes the performance of the Brazilian-American Commission of Industrial Education (CBAI) since its installation at Rio de Janeiro, on 1947, and extinction in Curitiba, on 1963. The general goal consists in identifying if are there any relation between Gramsci’s Americanism and Fordism elements and the CBAI’s performance, by means of a speech analysis from de Newsletter of CBAI and other documental sources related to the organizations performance. The specifics objectives intend to contextualize the political and economic situation that Brazil was going through before and concomitant to CBAI’s performance, emphasizing some aspects of the Cold War feature that contributed to narrow the relations between United States and other countries of Latin America, especially Brazil. On the following, it intends to present the main aspects of Gramsci’s thought and the Americanism and fordism and Passive Revolution as key categories for a better understanding of the presence of an Americanization project on Brazilian’s professional education. As so, the object of this study are the Newsletters of CBAI. Finally, the speech’s analisys of the Newsletter was the methodology used to demonstrate CBAI as an Americanism diffuser. The documental research and sources served as groundwork, especially the Newsletters, were found at Departamento de Documentação Histórica of Universidade Tecnológica Federal do Paraná (DEDHIS) and at Biblioteca de Educação of Universidade de São Paulo (FEUSP). The theoretical foundation has as a workline for the conception of the categories the studies of Gramsci about the of work (and the Newsletters itself), and the speech’s analysis of main concepts from Bakhtin, Voloshinov’s and the Circle of studies about language philosophy. At last, this paperwork concludes that the attempt to disseminate an amerizanization project in Brazil obtneined significant results on the industrialization of the country according to the fordism’s racionalization standarts, nevertheless, this research considers that such a project corroborates the comprehension about the consolidation of a Passive Revolution’s project.

The use of mechanical aeration and its effects on water mass

Devido ao crescente aumento do uso de aeradores artificiais em sistema de cultivo de peixes e à carência de estudos nesta área, este trabalho avaliou a influência de um aerador tipo propeller diffuser (AR 120) nas variáveis bióticas e abióticas em um viveiro de engorda de peixe. Foram demarcados três pontos de coleta localizados a 5, 10 e 23 m de distância do aerador, durante 15 dias consecutivos, sendo 5 dias antes do uso do aerador, 5 dias com o aerador ligado e 5 dias com o aerador desligado. As variáveis limnológicas estudadas não apresentaram diferenças significativas (P > 0,05) entre os três pontos de coleta, porém, em relação ao uso do aerador, variáveis como temperatura, transparência, pH, oxigênio dissolvido, bicarbonato, CO2 livre, fósforo total, ortofosfato, amônia, nitrato e nitrito diferiram significativamente (P < 0,05) com a agitação mecânica da água. Já a condutividade, alcalinidade, CO2 total e clorofila a não apresentaram diferenças significativas (P > 0,05) com o uso do aerador. A comunidade fitoplanctônica sofreu influência direta do aerador (P < 0,05), dominada pelas Chlorophyta, representando mais de 70% do total de organismos presentes, seguidas das Cyanophyta e Chrysophyta, porém estas últimas tenderam a aumentar após o uso do aerador, uma vez que estes grupos se adaptam rapidamente às mudanças do ambiente.

Simulação do escoamento monofásico em um estágio de uma bomba centrífuga utilizando técnicas de fluidodinâmica computacional

Oil production and exploration techniques have evolved in the last decades in order to increase fluid flows and optimize how the required equipment are used. The base functioning of Electric Submersible Pumping (ESP) lift method is the use of an electric downhole motor to move a centrifugal pump and transport the fluids to the surface. The Electric Submersible Pumping is an option that has been gaining ground among the methods of Artificial Lift due to the ability to handle a large flow of liquid in onshore and offshore environments. The performance of a well equipped with ESP systems is intrinsically related to the centrifugal pump operation. It is the pump that has the function to turn the motor power into Head. In this present work, a computer model to analyze the three-dimensional flow in a centrifugal pump used in Electric Submersible Pumping has been developed. Through the commercial program, ANSYS® CFX®, initially using water as fluid flow, the geometry and simulation parameters have been defined in order to obtain an approximation of what occurs inside the channels of the impeller and diffuser pump in terms of flow. Three different geometry conditions were initially tested to determine which is most suitable to solving the problem. After choosing the most appropriate geometry, three mesh conditions were analyzed and the obtained values were compared to the experimental characteristic curve of Head provided by the manufacturer. The results have approached the experimental curve, the simulation time and the model convergence were satisfactory if it is considered that the studied problem involves numerical analysis. After the tests with water, oil was used in the simulations. The results were compared to a methodology used in the petroleum industry to correct viscosity. In general, for models with water and oil, the results with single-phase fluids were coherent with the experimental curves and, through three-dimensional computer models, they are a preliminary evaluation for the analysis of the two-phase flow inside the channels of centrifugal pump used in ESP systems

Stilling Basin Scour Remediation Using Air Injection and Flat Plate Extension

The South Florida Water Management District (SFWMD) is responsible for managing over 2500 miles of waterways and hundreds of water control structures. Many of these control structures are experiencing erosion, known as scour, of the sediment downstream of the structure. Laboratory experiments were conducted in order to investigate the effectiveness of two-dimensional air diffusers and plate extensions (without air injection) on a 1/30 scale model of one of SFWMD gated spillway structures, the S65E gated spillway. A literature review examining the results of similar studies was conducted. The experimental design for this research was based off of previous work done on the same model. Scour of the riverbed downstream of gated spillway structures has the potential to cause serious damage, as it can expose the foundation of the structure, which can lead to collapse. This type of scour has been studied previously, but it continues to pose a risk to water control structures and needs to be studied further. The hydraulic scour channel used to conduct experiments contains a head tank, flow straighteners, gated spillway, stilling basin, scour chamber, sediment trap, and tailwater tank. Experiments were performed with two types of air diffusers. The first was a hollow, acrylic, triangular end sill with air injection holes on the upstream face, allowing for air injection upstream. The second diffuser was a hollow, acrylic rectangle that extended from the triangular end sill with air injection holes in the top face, allowing for vertical air injection, perpendicular to flow. Detailed flow and bed measurements were taken for six trials for each diffuser ranging from no air injection to 5 rows of 70 holes of 0.04" diameter. It was found that with both diffusers, the maximum amount of air injection reduced scour the most. Detailed velocity measurements were taken for each case and turbulence statistics were analyzed to determine why air injection reduces scour. It was determined that air injection reduces streamwise velocity and turbulence. Another set of experiments was performed using an acrylic extension plate with no air injection to minimize energy costs. Ten different plate lengths were tested. It was found that the location of deepest scour moved further downstream with each plate length. The 32-cm plate is recommended here. Detailed velocity measurements were taken after the cases with the 32-cm plate and no plate had reached equilibrium. This was done to better understand the flow patterns in order to determine what causes the scour reduction with the extension plates. The extension plate reduces the volume of scour, but more importantly translates the deepest point of scour downstream from the structure, lessening the risk of damage.

MULTI-WAVELENGTH SPECKLE REDUCTION FOR LASER PICO-PROJECTORS USING DIFFRACTIVE OPTICS

Personal electronic devices, such as cell phones and tablets, continue to decrease in size while the number of features and add-ons keep increasing. One particular feature of great interest is an integrated projector system. Laser pico-projectors have been considered, but the technology has not been developed enough to warrant integration. With new advancements in diode technology and MEMS devices, laser-based projection is currently being advanced for pico-projectors. A primary problem encountered when using a pico-projector is coherent interference known as speckle. Laser speckle can lead to eye irritation and headaches after prolonged viewing. Diffractive optical elements known as diffusers have been examined as a means to lower speckle contrast. Diffusers are often rotated to achieve temporal averaging of the spatial phase pattern provided by diffuser surface. While diffusers are unable to completely eliminate speckle, they can be utilized to decrease the resultant contrast to provide a more visually acceptable image. This dissertation measures the reduction in speckle contrast achievable through the use of diffractive diffusers. A theoretical Fourier optics model is used to provide the diffuser’s stationary and in-motion performance in terms of the resultant contrast level. Contrast measurements of two diffractive diffusers are calculated theoretically and compared with experimental results. In addition, a novel binary diffuser design based on Hadamard matrices will be presented. Using two static in-line Hadamard diffusers eliminates the need for rotation or vibration of the diffuser for temporal averaging. Two Hadamard diffusers were fabricated and contrast values were subsequently measured, showing good agreement with theory and simulated values. Monochromatic speckle contrast values of 0.40 were achieved using the Hadamard diffusers. Finally, color laser projection devices require the use of red, green, and blue laser sources; therefore, using a monochromatic diffractive diffuser may not optimal for color speckle contrast reduction. A simulation of the Hadamard diffusers is conducted to determine the optimum spacing between the two diffusers for polychromatic speckle reduction. Experimental measured results are presented using the optimal spacing of Hadamard diffusers for RGB color speckle reduction, showing 60% reduction in contrast.