Effects of biodiesel chemical composition on the chemical and physical properties of the primary and secondary diesel particulate matter

This thesis improves our insight towards the effects of using biodiesels on the particulate matter emission of diesel engines and contributes to our understanding of their potential adverse health effects. The novelty of this project is the use of biodiesel fuel with controlled chemical composition that enables us to relate changes of physiochemical properties of particles to specific properties of the biodiesel. For the first time, the possibility of a correlation of the volatility and the Reactive Oxygen Species concentration of the particles is investigated versus the saturation, oxygen content and carbon chain length of the fuel.

Performance of an Al-Si-graphite particle composite piston in a diesel engine

Al-Si-graphite particle composite alloy pistons containing different percentages of about 80 μm uncoated graphite particles were successfully cast by foundry techniques. Tests with a 5 hp single-cylinder diesel engine show that Al-Si-graphite particle composite pistons can withstand an endurance test of 500 h without any apparent deterioration and do not seize during the running-in period. The use of the Al-Si-3% graphite particle composite piston also results in (a) up to 3% reduction in the specific fuel consumption, (b) considerable reduction in the wear of all four piston rings, (c) a reduction in piston wear, (d) a 9% reduction in the frictional horsepower losses of the engine as determined by the motoring test and (e) a slight increase in the exhaust gas temperature. These reductions (a)–(d) appear to be due to increased lubrication from the graphite particles which are smeared on the bearing surface, the higher damping capacity of the composite pistons and the reduced coefficient of thermal expansion of the composite pistons. Preliminary results indicate that aluminum-graphite particle composite alloy is a promising material for automotive pistons.

Experimental investigation of the effects of oxygenated fuels on exhaust emissions in a heavy duty diesel engine

Physical and chemical properties of biofuels vary among various feedstocks and their subsequent conversions to fuels. The biofuels contain various amounts of oxygen, and this has a significant influence on exhaust emission. This oxygen content has been considered in order to investigate its effect on diesel engine exhaust emissions. The experiments have been conducted with a heavy duty diesel engine and various oxygenated fuels. It is found that the amount of oxygen in the fuel has a high level of influence on its exhaust emissions, and this provides agreement with diesel emissions results such as PN reduction. By increasing the amount of oxygen in the blend (by adding more biofuel), the particulate number (PN) is reduced and NOx increases gradually. However, the variation of PN and NOx are not similar for waste cooking biodiesel (WCBD) and butanol blend, even though their oxygen content are the same in the blends. This is due to the source of the biofuel and their internal chemistry.

Diesel Engine Driven Stand-Alone Variable Speed Constant Frequency Slip Ring Induction Generator - Theory and Experimental Results

The operation of a stand-alone, as opposed to grid connected generation system, using a slip-ring induction machine as the electrical generator, is considered. In contrast to an alternator, a slip-ring induction machine can run at variable speed and still deliver constant frequency power to loads. This feature enables optimization of the system when the prime mover is inherently variable speed in nature eg. wind turbines, as well as diesel driven systems, where there is scope for economizing on fuel consumption. Experimental results from a system driven by a 44 bhp diesel engine are presented. Operation at subsynchronous as well as super-synchronous speeds is examined. The measurement facilitates the understanding of the system as well as its design.

Potential of bio-DME as a transportation fuel for India

This article discusses the potential of bio-dimethyl ether (DME) as a promising fuel for India in the transportation sector where a majority of imported petroleum in the form of diesel is used. Specifically, the suitability of DME in terms of its properties vis-a-vis those of diesel, ability to liquefy DME at low pressures similar to liquefied petroleum gas (LPG), and ease of production from renewable feedstock (biomass), and most importantly, very low emissions including near-zero soot levels are some of the features that make it an attractive option. A detailed review presents the state-of-the-art on various aspects such as estimates of potential bio-DME production, methods of synthesis of bio-DME, important physicochemical properties, fuel-injection system-related concerns (both conventional and common-rail system), fuel spray characteristics which have a direct bearing on the engine performance, and finally, exhaust emissions. Future research directions covering all aspects from production to utilization are summarized (C) 2010 American Institute of Physics. doi:10.1063/1.3489529]

Dry tribology and nanomechanics of gaseous flame soot in comparison with carbon black and diesel soot

Ethylene gas is burnt and the carbon soot particles are thermophoretically collected using a home-built equipment where the fuel air injection and intervention into the 7.5-cm long flame are controlled using three small pneumatic cylinders and computer-driven controllers. The physical and mechanical properties and tribological performance of the collected soot are compared with those of carbon black and diesel soot. The crystalline structures of the nanometric particles generated in the flame, as revealed by high-resolution transmission electron studies, are shown to vary from the flame root to the exhaust. As the particle journeys upwards the flame, through a purely amorphous coagulated phase at the burner nozzle, it leads to a well-defined crystalline phase shell in the mid-flame zone and to a disordered phase consisting of randomly distributed short-range crystalline order at the exhaust. In the mid-flame region, a large shell of radial-columnar order surrounds a dense amorphous core. The hardness and wear resistance as well as friction coefficient of the soot extracted from this zone are low. The mechanical properties characteristics of this zone may be attributed to microcrystalline slip. Moving towards the exhaust, the slip is inhibited and there is an increase in hardness and friction compared to those in the mid-flame zone. This study of the comparison of flame soot to carbon black and diesel soot is further extended to suggest a rationale based on additional physico-chemical study using micro-Raman spectroscopy.

Vaporization and collision modeling of liquid fuel sprays in a co-axial fuel and air pre-mixer

Droplet collision occurs frequently in regions where the droplet number density is high. Even for Lean Premixed and Pre-vaporized (LPP) liquid sprays, the collision effects can be very high on the droplet size distributions, which will in turn affect the droplet vaporization process. Hence, in conjunction with vaporization modeling, collision modeling for such spray systems is also essential. The standard O'Rourke's collision model, usually implemented in CFD codes, tends to generate unphysical numerical artifact when simulations are performed on Cartesian grid and the results are not grid independent. Thus, a new collision modeling approach based on no-time-counter method (NTC) proposed by Schmidt and Rutland is implemented to replace O'Rourke's collision algorithm to solve a spray injection problem in a cylindrical coflow premixer. The so called ``four-leaf clover'' numerical artifacts are eliminated by the new collision algorithm and results from a diesel spray show very good grid independence. Next, the dispersion and vaporization processes for liquid fuel sprays are simulated in a coflow premixer. Two liquid fuels under investigation are jet-A and Rapeseed Methyl Esters (RME). Results show very good grid independence in terms of SMD distribution, droplet number distribution and fuel vapor mass flow rate. A baseline test is first established with a spray cone angle of 90 degrees and injection velocity of 3 m/s and jet-A achieves much better vaporization performance than RME due to its higher vapor pressure. To improve the vaporization performance for both fuels, a series of simulations have been done at several different combinations of spray cone angle and injection velocity. At relatively low spray cone angle and injection velocity, the collision effect on the average droplet size and the vaporization performance are very high due to relatively high coalescence rate induced by droplet collisions. Thus, at higher spray cone angle and injection velocity, the results expectedly show improvement in fuel vaporization performance since smaller droplet has a higher vaporization rate. The vaporization performance and the level of homogeneity of fuel-air mixture can be significantly improved when the dispersion level is high, which can be achieved by increasing the spray cone angle and injection velocity. (C) 2012 Elsevier Ltd. All rights reserved.

BIOMASS GASIFICATION TO SUBSTITUTE FOSSIL FUEL IN FOOD INDUSTRY

Food industries like biscuit and confectionary use significant amount of fossil fuel for thermal energy. Biscuit manufacturing in India is carried out both by organized and unorganized sector. The ratio of organized to unorganized sector is 60 : 40 (1). The total biscuit manufacturing in the organized sector India in 2008 was about 1.7 million metric tons (1). Accounting for the unorganized sector in India, the total biscuit manufacturing would have been about 2.9 million metric tons/annum. A typical biscuit baking is carried in a long tunnel kiln with varying temperature in different zones. Generally diesel is used to provide the necessary heat energy for the baking purpose, with temperature ranging from 190 C in the drying zone to about 300 C in the baking area and has to maintain in the temperature range of +/- 5 C. Typical oil consumption is about 40 litres per ton of biscuit production. The paper discusses the experience in substituting about 120 lts per hour kiln for manufacturing about 70 tons of biscuit daily. The system configuration consists of a 500 kg/hr gasification system comprising of a reactor, multicyclone, water scrubbers, and two blowers for maintaining the constant gas pressure in the header before the burners. Cold producer gas is piped to the oven located about 200 meters away from the gasifier. Fuel used in the gasification system is coconut shells. All the control system existing on the diesel burner has been suitably adapted for producer gas operation to maintain the total flow, A/F control so as to maintain the temperature. A total of 7 burners are used in different zones. Over 17000 hour of operation has resulted in replacing over 1800 tons of diesel over the last 30 months. The system operates for over 6 days a week with average operational hours of 160. It has been found that on an average 3.5 kg of biomass has replaced one liter of diesel.

Remoção de compostos sulfurados e nitrogenados de diesel hidrotratado por adsorção em argila, alumina e sílica-alumina, impregnadas com metais de transição

Na matriz energética brasileira, o óleo diesel tem lugar de destaque, porém ainda é comercializado com teores de compostos sulfurados e nitrogenados considerados altos para as legislações ambientais que entrarão em vigor nos próximos anos. Tradicionalmente, a remoção desses compostos de enxofre de correntes de petróleo é realizada por processos de hidrotratamento (HDT). No entanto, devido as características do diesel brasileiro, se faz necessária maior severidade para atingir as novas especificações dos combustíveis. Isto implica em investimentos e custos operacionais crescentes para atender a demanda que se instala. Neste contexto, a adsorção está sendo estudada para a purificação da corrente de óleo diesel oriunda da etapa de hidrotratamento como polimento final para alcançar as especificações mais exigentes. Sabe-se que os adsorventes comerciais apresentam limitações na remoção destes contaminantes e uma alternativa que tem se mostrado promissora é a incorporação de metais de transição na estrutura do sólido. No presente trabalho foram modificados adsorventes comerciais, tais como aluminas, sílica-aluminas e argilas pela introdução dos elementos níquel, colbalto e molibdênio e testado o desempenho dessas modificações frente à adsorção de compostos sulfurados e nitrogenados presentes em um diesel hidrotratado. Foram feitas caracterizações químicas, físicas, texturais e morfológicas dos sólidos com e sem incorporação de metais de transição na estrutura original. Os experimentos de adsorção foram realizados a 40C. Avaliando todos os sólidos, o adsorvente que mostrou o melhor desempenho na remoção de compostos sulfurados e nitrogenados por massa de adsorvente foi a sílica-alumina sem modificações, que foi capaz de remover em torno de 90% de compostos nitrogenados e 55 % de sulfurados para 2 g de sólido / 10 mL de diesel. Para os materiais modificados, observou-se que a incorporação dos metais de transição ocasionou redução da sua área superficial e do volume total de poros. Desta maneira, os efeitos esperados pelas interações entre o sítios metálicos e os compostos de nitrogênio e enxofre foram reduzidos

Avaliação de diferentes estratégias de biorremediação no tratamento de solo contaminado por diesel B5

No Brasil, a contaminação do solo por derramamentos de combustíveis representa um dos mais graves problemas ambientais e o impacto da introdução de novas misturas como diesel/biodiesel na matriz energética requer investigação quanto a tecnologias apropriadas de remediação. O presente estudo teve por objetivo avaliar diferentes estratégias de biorremediação no tratamento de solo contaminado experimentalmente com óleo diesel B5. Foram conduzidos três experimentos. No primeiro, quatro microcosmos em duplicata, contendo 500 g de solo e 5% (p/p) de óleo diesel B5, todos suplementados com oxigênio através de revolvimento manual e com ajuste de umidade, tiveram como tratamentos: bioestímulo com ajuste de pH (BE1); bioestímulo com ajuste de pH e nutrientes (BE2); bioaumento com ajuste de pH, nutrientes e adição de consórcio microbiano comercial KMA (BAM) e; controle abiótico, com ajuste de pH e solo esterilizado em autoclave (PA). Paralelamente, foi conduzido tratamento por bioaumento com ajuste de pH e nutrientes, suplementação de oxigênio e consórcio KMA, em solo contaminado apenas por diesel a 5% (BAD). A população microbiana foi monitorada através da contagem de UFC e os tratamentos, avaliados pela remoção de carbono orgânico e de hidrocarbonetos de petróleo (n-alcanos C10-C36). No segundo experimento, o metabolismo microbiano aeróbio foi avaliado através da produção de CO2 em respirômetros de Bartha (triplicatas), em solo contaminado com 5% (p/p) de óleo diesel B5, ajustado para pH e umidade, nas seguintes condições: solo com adição do consórcio KMA; solo com adição de cultura microbiana obtida a partir de outro solo proveniente de um posto de combustível com histórico de vazamento de tanques (RES) e; solo esterilizado por adição de azida de sódio a 0,3% (p/p). Como controle, solo sem contaminação, com sua população microbiana autóctone. No terceiro experimento, a capacidade da microbiota autóctone (EX), assim como do consórcio KMA e da cultura RES, em biodegradar óleo diesel B5, diesel e biodiesel de soja foi testada através do uso de indicadores de oxirredução DCPIP e TTC. Os experimentos em microcosmos indicam que houve uma complementaridade metabólica entre a população nativa e o consórcio comercial de microorganismos KMA, cuja presença promoveu um decaimento mais rápido de n-alcanos nas primeiras semanas do experimento. No entanto, após 63 dias de experimento, os tratamentos BAM, BAD e BE2 apresentaram, respectivamente, em média, 92,7%, 89,4% e 81,7% de remoção dos hidrocarbonetos n-alcanos C10-C36, sendo tais diferenças, sem significância estatística. Nos respirômetros, o bioaumento com cultura microbiana RES apresentou a maior produção de CO2 e a maior remoção de hidrocarbonetos (46,2%) após 29 dias. Tanto nos ensaios em microcosmos quanto nos respirométricos, não foi possível estimar a contribuição dos processos abióticos, tendo em vista evidências da existência de atividade microbiana no solo esterilizado térmica ou quimicamente. Os ensaios com os dois indicadores redox mostraram que apenas a microbiota nativa do solo em estudo e a cultura microbiana RES apresentaram potencial para degradar óleo diesel B5, biodiesel de soja ou diesel, quando colocadas em meio mineral contendo tais combustíveis como única fonte de carbono.

Quantificação de metais e arsênio em aerossóis grossos, finos, ultrafinos e nanoparticulados por ICP-OES em ar ambiente e emissões veiculares de motores operando com diesel/biodiesel

Na frota automotiva nacional, veículos movidos a diesel e biodiesel são utilizados em larga e pequena escala, respectivamente, fazendo com que haja uma preocupação com os gases da exaustão provenientes destes motores. Ao ser fabricado, o veículo passa por testes rigorosos das emissões gasosas, segundo as regras do PROCONVE. Porém, estes testes regulam apenas as substâncias químicas contidas na legislação vigente, cujos riscos à saúde humana e ao meio ambiente são conhecidos. Portanto, conhecer o maior número de componentes ainda não contemplados pela legislação, em especial metais no material particulado, é de suma importância para subsidiar futuras alterações e inclusões na lista de componentes regulados. De acordo com o tamanho das partículas do material particulado, podendo chegar a escalas nanométricas, a inalação deste material pode causar lesões graves no organismo, pois têm a capacidade de atingir órgãos internos. O estudo é baseado na amostragem do material particulado proveniente dos gases de motores alimentados com diesel e/ou biodiesel em diferentes proporções de combustível e ar ambiente com impactador em cascata; determinando metais e arsênio na atmosfera de diferentes localidades do estado do Rio de Janeiro e no material particulado dos gases de escape de motores de ônibus/caminhão (EURO III), por intermédio de abertura ácida do material coletado e da técnica analítica ICP-OES. Os resultados obtidos para motor EURO III variaram de 100 a 10000 ng m-3, com a redução de emissão conforme adição de biodiesel no diesel sendo comprovada. Porém, em todas as proporções de combustíveis empregadas, houve grande incidência de emissão de partículas em escala manométrica, sendo esse comportamento também observado nas amostragens em ar ambiente. Neste caso, teores de 1,0 a 45,0 ng m-3 evidenciaram Caxias e Madureira como locais mais poluídos dos amostrados. Ni é o metal que possui situação mais alarmante, pois em todos os tamanhos de partícula e locais amostrados, os teores deste elemento foram superiores ao permitido pela legislação internacional. A análise estatística multivariada propôs que os combustíveis B10 e B15 são quimicamente semelhantes, enquanto B5 e B20 sofrem fortes alterações no decorrer de sua combustão e a correlação de Pearson mostrou em ar ambiente, que locais com níveis próximos de poluição apresentaram similaridade nos resultados, a qualidade do ar de Madureira é afetado predominantemente pela construção civil e tráfego, a presença da Baía de Guanabara ao redor da Cidade Universitária influencia nas emissões, a refinaria em Caxias é responsável por emissões importantes de metais e no Parque Nacional de Itatiaia , ao contrário de que se supunha, não está totalmente livre de poluição

Multi-dimensional conditional moment closure modelling applied to a heavy-duty common-rail diesel engine

A multi-dimensional combustion code implementing the Conditional Moment Closure turbulent combustion model interfaced with a well-established RANS two- phase flow field solver has been employed to study a broad range of operating conditions for a heavy duty direct-injection common-rail Diesel engine. These conditions include different loads (25%, 50%, 75% and full load) and engine speeds (1250 and 1830 RPM) and, with respect to the fuel path, different injection timings and rail pressures. A total of nine cases have been simulated. Excellent agreement with experimental data has been found for the pressure traces and the heat release rates, without adjusting any model constants. The chemical mechanism used contains a detailed NOx sub-mechanism. The predicted emissions agree reasonably well with the experimental data considering the range of operating points and given no adjustments of any rate constants have been employed. In an effort to identify CPU cost reduction potential, various dimensionality reduction strategies have been assessed. Furthermore, the sensitivity of the predictions with respect to resolution in particular relating to the CMC grid has been investigated. Overall, the results suggest that the presented modelling strategy has considerable predictive capability concerning Diesel engine combustion without requiring model constant calibration based on experimental data. This is true particularly for the heat release rates predictions and, to a lesser extent, for NOx emissions where further progress is still necessary. © 2009 SAE International.

Non-catalytic multi-fuel reformer for syngas production for fuel cell applications

Rich combustion of n-heptane, diesel oil, jet A-1 kerosene, and bio-diesel (rapeseed-oil methyl ester) were studied to produce hydrogen enriched gas, ready for the cleanup stages for fuel cell applications. n-heptane was successfully reformed up to an equivalence ratio of 3:1, reaching a conversion efficiency up to 83% for a packed bed of alumina bead burner. Diesel, kerosene and bio-diesel were reformed to synthesis gas with conversion efficiency up to 65%. At equivalence ratio of 2:1 and P=7 kw, stability, low HC formation, high conversion efficiency, and low soot emission were achieved. A common synthesis gas composition around this condition was 15 and 13% H2, 15 and 17% CO, and 4 and 4.5% CO2 for n-heptane and diesel, jet A-1 and bio-diesel, respectively, for burner A. This is an abstract of a paper presented at the 2010 Spring National Meeting (San Antonio, TX 3/21-25/2010).

Diesel Cylinder Charge Properties: Feed-Forward Control and Cycle-by-Cycle Analysis Using an In-Cylinder Gas Sampling System

Common-rail fuel injection systems on modern light duty diesel engines are effectively able to respond instantaneously to changes in the demanded injection quantity. In contrast, the air-system is subject to significantly slower dynamics, primarily due to filling/emptying effects in the manifolds and turbocharger inertia. The behaviour of the air-path in a diesel engine is therefore the main limiting factor in terms of engine-out emissions during transient operation. This paper presents a simple mean-value model for the air-path during throttled operation, which is used to design a feed-forward controller that delivers very rapid changes in the in-cylinder charge properties. The feed-forward control action is validated using a state-of-the-art sampling system that allows true cycle-by-cycle measurement of the in-cylinder CO2 concentration. © 2011 SAE International.

Autoignition of monodisperse biodiesel and diesel sprays in turbulent flows

A new experimental configuration has been developed to examine the effects of flow on the autoignition of dilute diesel and biodiesel sprays, where the spray is injected in the form of monodisperse individual droplets at right angles to a hot air turbulent flow. The ignition location has been measured by monitoring the OH * chemiluminescence. A qualitative comparison of the flame behaviour between ethanol, acetone, heptane and biodiesel as fuels has also been carried out. With decreasing volatility of the fuel, the flame showed progressively a higher number of individual droplets burning, with the first autoignition spots appearing at random locations but in general earlier than the intense droplet-flame emission. The time-averaged autoignition length increased with increasing air velocity and with increasing intensity of the turbulence, while it decreased with the temperature and the droplet size. The data can be used for validating models for two-phase turbulent combustion. © 2012 Elsevier Inc.