Otimização do fresamento de roscas internas com a técnica de interpolação helicoidal

In machining of internal threads, dedicated tools, known as taps, are needed for each profile type, diameter, and low cutting speed values are used when compared to main machining processes. This restriction in the cutting speed is associated with the difficulty of synchronizing the tool s rotation speed and feed velocity in the process. This fact restricts the flexibility and makes machining lead times longer when manufacturing of components with threads is required. An alternative to the constraints imposed by the tap is the thread milling with helical interpolation technique. The technique is the fusion of two movements: rotation and helical interpolation. The tools may have different configurations: a single edge or multiple edges (axial, radial or both). However, thread milling with helical interpolation technique is relatively new and there are limited studies on the subject, a fact which promotes challenges to its wide application in the manufacturing shop floor. The objective of this research is determine the performance of different types of tools in the thread milling with helical interpolation technique using hardened steel workpieces. In this sense, four tool configurations were used for threading milling in AISI 4340 quenched and tempered steel (40 HRC). The results showed that climb cut promoted a greater number of machined threads, regardless of tool configuration. The upcut milling causes chippings in cutting edge, while the climb cutting promotes abrasive wear. Another important point is that increase in hole diameter by tool diameter ratio increases tool lifetime

Artificial neural networks for machining processes surface roughness modeling

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Evaluation of the performance of α-SiAlON tool when turning Ti-6Al-4V alloy without coolant

Due to their high hardness and wear resistance, Si3N4 based ceramics are one of the most suitable cutting tool materials for machining cast iron, nickel alloys and hardened steels. However, their high degree of brittleness usually leads to inconsistent results and sudden catastrophic failures. This necessitates a process optimization when machining superalloys with Si3N4 based ceramic cutting tools. The tools are expected to withstand the heat and pressure developed when machining at higher cutting conditions because of their high hardness and melting point. This paper evaluates the performance of α-SiAlON tool in turning Ti-6Al-4V alloy at high cutting conditions, up to 250 m min-1, without coolant. Tool wear, failure modes and temperature were monitored to access the performance of the cutting tool. Test results showed that the performance of α-SiAl0N tool, in terms of tool life, at the cutting conditions investigated is relatively poor due probably to rapid notching and excessive chipping of the cutting edge. These facts are associated with adhesion and diffusion wear rate that tends to weaken the bond strength of the cutting tool.

E-business innovation and customs renovation for secure supply chain management

Includes bibliography

Analysis on turning Ti-6Al-4V with different cooling methods

The aim of this paper is to optimize the machining of Ti-6Al-4V alloy, by studying the chip formation, roughness and tool wear for different cooling conditions. The results were compared between cooling methods, minimal quantity of fluid (MQF) and flooding, and also without fluid for the tool H13A. The turning of Ti-6Al-4V has shown good results on roughness (0, 8μm) and tool life, which was 11% lower with MQF than with the flooding method. The tool wear causes variation of the shear angle, which promotes strength hardening of the chip. As a result, the machined surface could be damaged. The use of the cutting fluid helps to save the cutting edge and could reduce the strength hardening. Nevertheless, it could also facilitate the formation of built-up edge. The nucleation of alpha lamellar colonies can occur due to a combination of deformation rates and temperature, mainly when the flooding is used, but it's not conclusive. The lamellar colonies were also found with the MQF in some regions, however, this structure did not show hardness variation compared to equiaxial. For all this reasons, the machining parameters might be carefully chosen.

Diálogos entre literatura e cinema: um estudo sobre The Dead de James Joyce

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo do uso de ferramentas cerâmicas na usinagem de inconel 718

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

An assessment of the economic and social impacts of climate change on the Coastal and Marine Sector in the Caribbean

Climate change poses special challenges for Caribbean decision makers related to the uncertainties inherent in future climate projections and the complex linkages between climate change, physical and biological systems, and socioeconomic sectors. At present, however, the Caribbean subregion lacks the adaptive capacity needed to address these challenges. The present report assesses the economic and social impacts of climate change on the coastal and marine sector in the Caribbean until 2050. It aims both to provide Caribbean decision makers with cutting edge information on the vulnerability to climate change of the subregion, and to facilitate the development of adaptation strategies informed by both local experience and expert knowledge.

Policy Brief: an assessment of the economic and social impacts of climate change on the coastal and marine sector in the Caribbean

Caribbean policymakers are faced with special challenges from climate change and these are related to the uncertainties inherent in future climate projections and the complex linkages among climate change, physical and biological systems and socioeconomic sectors. The impacts of climate change threaten development in the Caribbean and may well erode previous gains in development as evidenced by the increased incidence of climate migrants internationally. This brief which is based on a recent study conducted by the Economic Commission for Latin America and the Caribbean (LC/CAR/L.395)1 provides a synthesis of the assessment of the economic and social impacts of climate change on the coastal and marine sector in the Caribbean which were undertaken. It provides Caribbean policymakers with cutting-edge information on the region’s vulnerability and encourages the development of adaptation strategies informed by both local experience and expert knowledge. It proceeds from an acknowledgement that the unique combination of natural resources, ecosystems, economic activities, and human population settlements of the Caribbean will not be immune to the impacts of climate change, and local communities, countries and the subregion as a whole need to plan for, and adapt to, these effects. Climate and extreme weather hazards related to the coastal and marine sector encompass the distinct but related factors of sea level rise, increasing coastal water temperatures, tropical storms and hurricanes. Potential vulnerabilities for coastal zones include increased shoreline erosion leading to alteration of the coastline, loss of coastal wetlands, and changes in the abundance and diversity of fish and other marine populations. The study examines four key themes in the analysis: climate, vulnerability, economic and social costs associated with climate change impacts, and adaptive measures.

Causes and consequences of low rates of specialisation in science and technology in CDCC member countries

The importance of science and technology (S&T) in Small Island Developing States (SIDS) is clearly articulated in Chapter XI, paragraphs 57, 58, 61 and 62 of the Mauritius Strategy for the Further Implementation of the Programme of Action for Sustainable Development of Small Island Developing States (MSI). At the regional level, the Heads of Government of the Caribbean Community (CARICOM) noted the challenge that CARICOM member States face in competing in this new international economic environment in which the impact of scientific and technological change has created a knowledge-based global economy. Given the importance of S&T to development of Caribbean SIDS, the Economic Commission for Latin America and the Caribbean (ECLAC) Subregional Headquarters for the Caribbean embarked on a study to determine the causes and consequences of low rates of specialisation in S&T with a view to making recommendations for development of strategies for addressing these challenges. Data on postgraduate (Master of Science, Master of Philosophy and Doctor of Philosophy) enrolment and graduation in agriculture, engineering and the sciences from the three campuses of the University of the West Indies (UWI) as well as from the University of Technology in Jamaica and the University of Trinidad and Tobago (UTT) were examined and analysed. Face-to-face interviews were also held with key personnel from these institutions and a questionnaire was also served to individuals in key institutions. Results of the study revealed that although the number of students enrolled in higher degree programmes has increased in absolute terms, they are decreasing in relative terms. However, enrolment in agriculture has indeed declined while enrolment rates in engineering, although increasing, were not significantly high. Market forces have proved to be a main reason for this trend while facilities for the conduct and supervision of cutting-edge research, the disconnect between science and industry and societal labelling of scientists as “misfits” are also contributing to the situation. This has resulted in a reduced desire by students at all levels of the school system and faculty to be involved in S&T; lack of innovation; a better staffed private, as compared with public, sector; and poor remuneration in science-based employment. There also appears to be a gender bias in enrolment with more males than females being enrolled in engineering while the opposite is apparent in agriculture and the sciences. Recommendations for remedying this situation range from increasing investment in S&T, creating linkages between science and industry as well as with the international community, raising awareness of the value of S&T at all levels of the education system to informing policy to stimulate the science – innovation interface so as to promote intellectual property rights.

Prazer-sofrimento e saúde no trabalho com automação: estudo com operadores em empresas japonesas no Pólo Industrial de Manaus

A atual configuração do mundo do trabalho caracteriza-se pela complexidade e intensificação dos riscos à saúde do trabalhador. A presente tese aborda trabalho e saúde a partir do referencial da psicodinâmica de Dejours, privilegiando a categoria prazer-sofrimento, no contexto do trabalho com automação no Pólo Industrial de Manaus - PIM. Visando situar os aspectos macroeconômicos, apresenta-se a condição sócio-econômica dos operadores e o contexto da reestruturação produtiva do PIM, que se caracterizou por intensificação da automação. O objetivo dessa pesquisa foi analisar a organização de trabalho com automação e seus desdobramentos sobre a saúde dos operadores e das operadoras de máquina de inserção automática, focalizando o prazer-sofrimento e seus reflexos sobre o processo de saúde-adoecimento. Elegeu-se a abordagem qualitativa, em consonância com a fundamentação teórico-metodológica de Dejours. A pesquisa empírica foi realizada na área de inserção automática das duas empresas de origem japonesa, de grande porte, do segmento eletroeletrônico do PIM. Participaram como sujeitos 21 operadores de máquinas (dez de uma e onze de outra empresa). A principal fonte de dados foi a fala dos sujeitos, que responderam a uma entrevista individual semi-estruturada. Para a análise de dados foi realizada uma articulação da sistemática da Grounded Theory à base psicodinâmica, como opção de técnica qualitatativa adequada a entrevistas individuais. A preocupação com a “qualidade” se destacou como categoria central, mostrando-se presente em todas as esferas da organização de trabalho e modulando a vivência de prazer-sofrimento: dentre as principais fontes de prazer, realizar o trabalho com perfeição foi reiteradamente mencionado; em contrapartida, o medo de errar é uma das principais fontes de sofrimento, causa permanente de tensão, agravante do risco de adoecimento. O prazer provém da identificação com a tarefa de operar máquinas, de alta tecnologia, sem cometer erros; aprender mais e dominar a “tecnologia de ponta” é uma fonte de mobilização subjetiva. O sofrimento decorre da sobrecarga de trabalho, mal remunerado, sob intensa pressão por “qualidade”. Para suportar o sofrimento, os trabalhadores constroem estratégias coletivas de defesa: usam gracejos direcionados aos colegas que cometem erros, interpretados como recurso para reduzir o sofrimento originário do medo de falhar. Utilizam ainda grande diversidade de estratégias individuais de defesa, reflexo do individualismo. O reconhecimento, considerado na psicodinâmica como via privilegiada para a ressignificação do sofrimento, é pouco presente: menos de metade dos operadores se considera devidamente reconhecido por seu trabalho; mencionam os baixos salários como evidência da falta de reconhecimento. Em uma das empresas também falta o reconhecimento simbólico, agravando o sofrimento. O predomínio do sofrimento sobre o prazer no trabalho conduz a um desequilíbrio que resulta no uso exacerbado de defesas: manifestam-se as patologias sociais do trabalho, dentre as quais foi identificada a patologia da sobrecarga, relacionada à carga excessiva de trabalho que é importa aos operadores e às operadoras, pois à aquisição de máquinas corresponde a redução de pessoas. O sofrimento no trabalho, no PIM, está sendo intensificado com a automação, inserida no contexto de super-exploração do trabalho, integrante da organização flexível do capital.

Avaliação do efeito da afiação com diferentes técnicas sobre o ângulo de corte de curetas de Gracey

Pós-graduação em Odontologia - FOAR

Ensaios não destrutivos: metrologia e calibração

To perform the quality control of various industries like: petrochemical, nuclear, aerospace, steel, shipbuilding, pulp and paper, and inspection of welded products, castings, forgings, rolled products, among others, used the method of Non-Destructive Testing (NDT). The method is based on the physical properties of the material, so selecting a procedure more appropriate. The company Inter-Metro Serviços Especiais Ltda., with its cutting-edge laboratory, dedicated to the implementation of calibration services and measurement equipment for industrial, medical, occupational safety and Non-Destructive Testing (NDT). It has a trained team, providing guidance and providing support for improving procedures for testing and measuring

XSOFT: estudo de reconhecimento, exploração e prevenção de vulnerabilidades de software através de uma distribuição LINUX

This work aims to give greater visibility to the issue of software security, due to people talk a lot in security conferences, that much of both IT (Information Technology) staff and, more specifically, IS (Information Security) staff does not know this, and, thanks to the spread of the mobile computing and of the cloud computing, this lack of deeper knowledge on this subject is increasingly becoming worrisome. It aims too, make applications to be developed in a security manner, priorizing the security of the information processed. It attempts to demonstrate the secure coding techniques, the principles of software security, the means to identify software vulnerabilities, the cutting-edge software exploitation techniques and the mechanisms of mitigation. Nowadays, the security guys are in charge of the most of the security tests in applications, audits and pentests, and it is undeniable that the so-called security experts, most often come from computer network field, having few experience in software development and programming. Therefore, the development process does not consider the security issue, thanks to the lack of knowledge on the subject by the developer, and the security tests could be improved whether security experts had a greater know-how on application development. Given this problem, the goal here is to integrate information security with software development, spreading out the process of secure software development. To achieve this, a Linux distribution with proof of concept applicati... (Complete abstract click electronic access below)

Usinagem da liga de níquel inconel 718 com pastilhas de cerâmica

The machining of super alloys resistant to high temperatures such as nickel alloys, inconel 718 specifically, is a very difficult job to obtain improvements in the process, due to the difficulty of machining at high cutting speeds, the use of these alloys in industries showed great developments in recent years, its application in aeronautical industry spread being used in vane turbo, compressor parts, props and set elements. The automotive, chemical, medical and others also took advantage of the great features of inconel 718 and has used the material. The high temperature resistant alloys have high machining difficulty, a fact that is associated with high cutting forces generated during machining which result in high temperatures. High levels of temperatures can cause deterioration of the cutting edge, with subsequent deformation or breakage, wear most common obtained in machining such materials are flank wear the formation of built-up edge for cutting and notch wear. The experimental part of the work consists in machining of nickel-based alloy Inconel 718 heat treated for hardness, using a tool based ceramic silicon nitride Sandvik (Si3N4) in order to compare the best results obtained in the master's thesis of SANTOS (2010) who used a tool ceramics also the basis of silicon nitride which was developed in the doctoral thesis of SOUZA (2005). Assays were performed on a CNC lathe and was noted for each cutting edge results obtained. Tests were made starting from an initial condition of the tool with cutting speed of 200 m/min, feed 0.5 mm and 0.5 mm depth of cut was reduced cutting speed for the subsequent tests with the same conditions of feed and depth of cut. The tool presented wear instant under two 200 m/min and 100 m/min, premature rupture of 50 m/min and finally cut provided with difficulty... (Complete abstract click electronic access below)