Running-in wear of a compression ignition engine: Factors influencing the conformance between cylinder liner and piston rings

The conformance between the liner and rings of an internal combustion engine depends mainly on their linear wear (dimensional loss) during running-in. Running-in wear studies, using the factorial design of experiments, on a compression ignition engine show that at certain dead centre locations of piston rings the linear wear of the cylinder liner increases with increase in the initial surface roughness of the liner. Rough surfaces wear rapidly without seizure during running-in to promote quick conformance, so an initial surface finish of the liner of 0.8 μm c.l.a. is recommended. The linear wear of the cast iron liner and rings decreases with increasing load but the mass wear increases with increasing load. This discrepancy is due to phase changes in the cast iron accompanied by dimensional growth at higher thermal loads. During running-in the growth of cast iron should be minimised by running the engine at an initial load for which the exhaust gas temperature is approximately 180 °C.

Raman spectrum of hydroxylamine hydrochloride (NH3OH.Cl)

The Raman spectrum of hydroxylamine hydrochloride (NH3OH.Cl) in the form of a single crystal has been photographed usingλ 2536·5 excitation. 32 Raman lines with frequency shifts 40, 57, 78, 88, 111, 125, 135, 156, 187, 217, 250, 330, 550, 575, 1004, 1168, 1204, 1470, 1496, 1565, 1590, 1979, 2636, 2710, 2750, 2789, 2926, 2970, 3000, 3050, 3141 and 3220 cm.−1 have been recorded. Of these, the first 8 low-frequency lines belong to the external oscillation, while the four lines at 187, 217, 250 and 330 cm.−1 should be attributed to the vibrations of the hydrogen bond valence vibrations. The remaining Raman lines have been assigned to the vibrations of the NH3OH ion. The O-H and N-H stretching vibrations are very much influenced by the presence of the hydrogen bonds in the crystal.

Experimental studies on the wear of engine components

Wear studies of engine components of high-speed diesel engines running under various operating conditions are presented. Tests were conducted under controlled conditions over long periods. The results of the various tests are discussed and attempts have been made to examine the effects of engine operating variables and the quality of the lubricating oil on the wear of engine components.

Compliance of rough cylinders in compression

Compression of a rough turned cylinder between two hard, smooth, flat plates has been analysed with the aid of a mathematical model based on statistical analysis. It is assumed that the asperity peak heights follow Gaussian or normal and beta distribution functions and that the loaded asperities comply as though they are completely isolated from the neighbouring ones. Equations have been developed for the loadcompliance relation of the real surface using a simplified relation of the form W0 = K1δn for the load-compliance of a single asperity. Parameters K1 and n have considerable influence on the load-compliance curve and they depend on the material, tip angle of the asperity, standard deviation of the asperity peak height distribution and the density of the asperities.

Influence of microstructure on the wear of grinding media

Owing to the complexity of the wear process, high stress grinding abrasion is quite different from two-body abrasive wear. Reported data on two-body abrasive wear reveal that the wear decreases with an increase in steel hardness. This relationship can be established without having to consider the microstructure of the steel grinding medium. However, it is known that hardness cannot be directly employed to predict the wear of steel balls under three-body grinding abrasion, as occurs during dry grinding of ores in ball mills. The present work suggests that the wear behaviour of grinding balls can be classified according to the microstructural family to which they belong. Thus, in this work on AISI 52100 steel, the separate groups of microstructures were spheroidite—pearlite, bainite, tempered martensite and martensite with retained austenite. It appears that wear behaviour of the first three groups follows the same trend as that observed for two-body wear. The data suggest that an optimum level of retained austenite could improve the wear resistance of microstructures containing martensite.

Structural effects on the vaporization of high molecular weight esters

To understand the effect of molecular weight and branching on the heats of vaporization (AH,) and their flow behavior, AH, and viscosity (7) were measured at different temperatures in the high molecular weight ester series: linear flexible di-n-alkyl sebacates and compact branched triglycerides with molecular weight ranging from 300 to 900. AHv" values (AHv corrected to 298 K) have been obtained with experimental AH, and also computed according to the group additivity method; a smaller-CH,- group value of 3.8 kJ mol-' compared to the normal value of 5.0 kJ mol-' is found to give good agreement with the experimental data (within 2-5% error). Both ester series have the same AH," irrespective of their molecular features, namely,shape, flexibility, and polarity, suggesting the coiling of the molecules during vaporization. The segmental motion of these ester series during their flow and its dependence on their molecular features unlike AH,' are demonstrated by the correlation of the enthalpy of activation for viscous flow (AH*) and the ratio AE,/AH* = n (AE, is the energy of vaporization) with molecular weight.

The German Military Entrepreneur Ernst von Mansfeld and His Conduct of Asymmetrical Warfare in the Thirty Years War

The dissertation examines aspects of asymmetrical warfare in the war-making of the German military entrepreneur Ernst von Mansfeld during his involvement in the Thirty Years War. Due to the nature of the inquiry, which combines history with military-political theory, the methodological approach of the dissertation is interdisciplinary. The theoretical framework used is that of asymmetrical warfare. The primary sources used in the dissertation are mostly political pamphlets and newsletters. Other sources include letters, documents, and contemporaneous chronicles. The secondary sources are divided into two categories, literature on the history of the Thirty Years War and textbooks covering the theory of asymmetrical warfare. The first category includes biographical works on Ernst von Mansfeld, as well as general histories of the Thirty Years War and seventeenth-century warfare. The second category combines military theory and political science. The structure of the dissertation consists of eight lead chapters, including an introduction and conclusion. The introduction covers the theoretical approach and aims of the dissertation, and provides a brief overlook of the sources and previous research on Ernst von Mansfeld and asymmetrical warfare in the Thirty Years War. The second chapter covers aspects of Mansfeld s asymmetrical warfare from the perspective of operational art. The third chapter investigates the illegal and immoral aspects of Mansfeld s war-making. The fourth chapter compares the differing methods by which Mansfeld and his enemies raised and financed their armies. The fifth chapter investigates Mansfeld s involvement in indirect warfare. The sixth chapter presents Mansfeld as an object and an agent of image and information war. The seventh chapter looks into the counter-reactions, which Mansfeld s asymmetrical warfare provoked from his enemies. The eighth chapter offers a conclusion of the findings. The dissertation argues that asymmetrical warfare presented itself in all the aforementioned areas of Mansfeld s conduct during the Thirty Years War. The operational asymmetry arose from the freedom of movement that Mansfeld enjoyed, while his enemies were constrained by the limits of positional warfare. As a non-state operator Mansfeld was also free to flout the rules of seventeenth-century warfare, which his enemies could not do with equal ease. The raising and financing of military forces was another source of asymmetry, because the nature of early seventeenth-century warfare favoured private military entrepreneurs rather than embryonic fiscal-military states. The dissertation also argues that other powers fought their own asymmetrical and indirect wars against the Habsburgs through Mansfeld s agency. Image and information were asymmetrical weapons, which were both aimed against Mansfeld and utilized by him. Finally, Mansfeld s asymmetrical threat forced the Habsburgs to adapt to his methods, which ultimately lead to the formation of a subcontracted Imperial Army under the management and leadership of Albrecht von Wallenstein. Therefore Mansfeld s asymmetrical warfare ultimately paved way for the kind of state-monopolized, organised, and symmetrical warfare that has prevailed from 1648 onwards. The conclusion is that Mansfeld s conduct in the Thirty Years War matched the criteria for asymmetrical warfare. While traditional historiography treated Mansfeld as an anomaly in the age of European state formation, his asymmetrical warfare has begun to bear resemblance to the contemporary conflicts, where nation states no longer hold the monopoly of violence.

Dry sliding wear of A356-Al-SiCp composites

Aluminium alloy (A356)-SiC composites containing 15 and 25 wt.% silicon carbide particles (average size 43 μm) were tested for sliding wear at different loads using a pin on disc machine. Composites exhibited better wear resistance compared with unreinforced alloy up to a pressure of 26 MPa. Scanning electron microscopy examination of worn surfaces and subsurfaces show that the presence of dispersed SiC particles help in reducing the propensity of material flow at the surface, at the same time leading to the formation of an iron-rich layer on the surface.

Effect of microstructure and hardness on the grinding abrasive wear resistance of a ball bearing steel

Grinding media wear appears to be non-linear with the time of grinding in a laboratory-scale ball mill. The kinetics of wear can be expressed as a power law of the type w=atb, where the numerical constant a represents wear of a particular microstructure at time t = 1 min and b is the wear exponent which is independent of the particle size prevailing inside a ball mill at any instant of time of grinding. The wear exponent appears to be an indicator of the cutting wear mechanism in dry grinding: a plot of the inverse of the normalised wear exponent (Image ) versusHs (where Hs is the worn surface hardness of the media) yields a curve similar to that of a wear resistance plot obtained in the case of two-body sliding abrasive wear. This method of evaluating the cutting wear resistance of media is demonstrated by employing 15 different microstructures of AISI-SAE 52100 steel balls in dry grinding of quartz in a laboratory-scale ball mill.

Friction and wear of PTFE — a review

Polytetrafluoroethylene (PTFE) is an important engineering material. When rubbed or slid against a hard surface, PTFE exhibits a low coefficient of friction but a high rate of wear. These unique properties of the polymer have encouraged many mechanistic and physical examinations of the processes involved in the friction and wear of this polymer. A section of such work carried out over the past 30 years is reviewed here. When rubbed against a hard surface, the PTFE chain undergoes scission, creating active groups which chemically react with the counterface. This results in strong adhesion and a coherent transfer film. Further interaction between the bulk polymer and the transfer film gives rise to anisotropic deformation of the unit cell, which results in closeness of adjacent chains and easy shear between chains. Sliding brings about growth in as well as reorientation of crystallites situated in a very thin subsurface region of the bulk polymer. Such structural rearrangement facilitates the joining of adjacent aligned crystallites to form films and ribbons which emerge as debris.

A single network adaptive critic (SNAC) architecture for optimal control synthesis for a class of nonlinear systems

Even though dynamic programming offers an optimal control solution in a state feedback form, the method is overwhelmed by computational and storage requirements. Approximate dynamic programming implemented with an Adaptive Critic (AC) neural network structure has evolved as a powerful alternative technique that obviates the need for excessive computations and storage requirements in solving optimal control problems. In this paper, an improvement to the AC architecture, called the �Single Network Adaptive Critic (SNAC)� is presented. This approach is applicable to a wide class of nonlinear systems where the optimal control (stationary) equation can be explicitly expressed in terms of the state and costate variables. The selection of this terminology is guided by the fact that it eliminates the use of one neural network (namely the action network) that is part of a typical dual network AC setup. As a consequence, the SNAC architecture offers three potential advantages: a simpler architecture, lesser computational load and elimination of the approximation error associated with the eliminated network. In order to demonstrate these benefits and the control synthesis technique using SNAC, two problems have been solved with the AC and SNAC approaches and their computational performances are compared. One of these problems is a real-life Micro-Electro-Mechanical-system (MEMS) problem, which demonstrates that the SNAC technique is applicable to complex engineering systems.

Structure of N-tert-butyloxycarbonyl-[alpha]-aminoisobutyryl-DL-pipecolyl-[alpha]-aminoisobutyric acid methyl ester

C20H35N3O6 (Boc-Aib-DL-Pip-Aib-OMe, Boc = tert-butyloxycarbonyl, Aib = alpha-aminoisobutyric acid, Pip = pipecolic acid, OMe = methoxy), M(r) = 413.5, monoclinic, P2(1)/c, a = 18.055 (3), b = 15.048 (3), c = 17.173 (3) angstrom, beta = 91.7 (1)-degrees, V = 4663.8 (9) angstrom3, Z = 8, D(m) = 1.16, D(x) = 1.178 Mg m-3, lambda(Mo Kalpha) = 0.71069 angstrom, mu = 0.081 mm-1, F(000) = 1792, T = 297 K. The final R value for 4925 [I greater-than-or-equal-to 3sigma(I)] reflections is 0.065 (wR = 0.067). The peptide backbone of the two independent molecules in the asymmetric unit is folded at the -Aib-Pip- sequence to form a type-I (I') beta-bend stabilized by a 1 <-- 4 intramolecular N-H...O=C hydrogen bond between the Aib(3) peptide N-H and Boc urethane C=O groups.

Observations on the role of the steel disc counterface during the sliding of various structural ceramics

Sliding wear characteristics and mechanisms of structural ceramics, namely Al2O3, zirconia-toughened alumina, tetragonal zirconia polycrystals (TZP) and Si3N4 against a steel counterface are influenced by mechanical and tribochemical interactions, specific to the combinations studied. The present paper studies the role of the disc in the sliding wear process of the above ceramics. Experiments were conducted at a pressure of 15.5 MPa between 0.1 and 12.0 m s(-1) with ceramic pins sliding against an EN-24 steel disc. Except in the case of TZP, the disc morphology is sensitive to variations in speed rather than to the pin material. The disc track is (i) mildly abraded at low speeds (about 0.1-0.75 m s(-1)), (ii) severely abraded at intermediate speeds (about 1.0-3.0 m s(-1)), (iii) covered with black patches at high speeds (about 4.0-6.0 m s(-1)) and (iv) completely black at very high speeds (about 7.0-12.0 m s(-1)). In the case of TZP, although black patches appear, transfer of TZP onto the disc surface and high wear of TZP occurs at 4.0 m s(-1). The order of the wear of the disc estimated from profilometric measurements is the same for all the ceramics. Except for Si3N4, the onset of wear of the ceramics is associated with the appearance of deep 'V' grooves on either side of the profile of the disc track. This can be explained on the basis of the thermal and hardness variations. Although other interaction products specific to the ceramic pin are present, the formation of iron oxides dominates the wear of the disc.