Laboratory investigation of flow structure and resistance of high- and low-angle dunes

A prominent control on the flow over subaqueous dunes is the slope of the downstream leeside. While previous work has focused on steep (~30°), asymmetric dunes with permanent flow separation, little is known about dunes with lower lee-slope angles for which flow separation is absent or intermittent. Here, we present a laboratory investigation where we systematically varied the dune lee-slope, holding other geometric parameters and flow hydraulics constant, to explore effects on the turbulent flow field and flow resistance. Three sets of fixed dunes (lee-slopes of 10°, 20° and 30°) were separately installed in a 15 m long and 1 m wide flume and subjected to 0.20 m deep flow. Measurements consisted of high-frequency, vertical profiles collected with a Laser Doppler Velocimeter (LDV). We show that the temporal and spatial occurrence of flow separation decreases with dune lee-slope. Velocity gradients in the dune leeside depict a free shear layer downstream of the 30° dunes and a weaker shear layer closer to the bed for the 20° and 10° dunes. The decrease in velocity gradients leads to lower magnitude of turbulence production for gentle lee-slopes. Aperiodic, strong ejection events dominate the shear layer, but decrease in strength and frequency for low-angle dunes. Flow resistance of dunes decreases with lee-slope; the transition being non-linear. Over the 10°, 20° and 30° dunes, shear stress is 8%, 33% and 90 % greater than a flat bed, respectively. Our results demonstrate that dune lee-slope plays an important, but often ignored role in flow resistance.

Flow separation and roughness lengths over large bedforms in a tidal environment

This study characterises the shape of the flow separation zone (FSZ) and wake region over large asymmetric bedforms under tidal flow conditions. High resolution bathymetry, flow velocity and turbulence data were measured along two parallel transects in a tidal channel covered with bedforms. The field data are used to verify the applicability of a numerical model for a systematic study using the Delft3D modelling system and test the model sensitivity to roughness length. Three experiments are then conducted to investigate how the FSZ size and wake extent vary depending on tidally-varying flow conditions, water levels and bathymetry. During the ebb, a large FSZ occurs over the steep lee side of each bedform. During the flood, no flow separation develops over the bedforms having a flat crest; however, a small FSZ is observed over the steepest part of the crest of some bedforms, where the slope is locally up to 15°. Over a given bedform morphology and constant water levels, no FSZ occurs for velocity magnitudes smaller than 0.1 m s**-1; as the flow accelerates, the FSZ reaches a stable size for velocity magnitudes greater than 0.4 m s**-1. The shape of the FSZ is not influenced by changes in water levels. On the other hand, variations in bed morphology, as recorded from the high-resolution bathymetry collected during the tidal cycle, influence the size and position of the FSZ: a FSZ develops only when the maximum lee side slope over a horizontal distance of 5 m is greater than 10°. The height and length of the wake region are related to the length of the FSZ. The total roughness along the transect lines is an order of magnitude larger during the ebb than during the flood due to flow direction in relation to bedform asymmetry: during the ebb, roughness is created by the large bedforms because a FSZ and wake develops over the steep lee side. The results add to the understanding of hydrodynamics of natural bedforms in a tidal environment and may be used to better parameterise small-scale processes in large-scale studies.

Flow rates, hydraulic conductivities and permeabilities of sediments from ODP Holes 190-1173A and 190-1174B

Understanding the role of fluids in active accretionary prisms requires quantitative knowledge of parameters such as permeability. We report here the results of permeability tests on four samples from Ocean Drilling Program Leg 190 at the Nankai Trough accretionary prism-two from Site 1173 and two from Site 1174. Volcanic ash is present in one of the samples; otherwise, the material is hemipelagic mud. A constant-rate-of-flow technique was used at various effective pressures and rates of flow. The permeability of the four samples ranges between 10**-15 and 10**-18 m**2, with the ash-bearing sample showing the highest values.

Heat flow ratios of stations from the Iberian abyssal plain (Table 1)

New heat flow observations have been made in the Iberia abyssal plain off the Galicia margin along the transeat of Ocean Drilling Program Leg 149 drill sites. in order to investigate the nature of this unusually wide and deep continet-ocean transition region. Our results indicate the presence of three separate zones. Average values of 47.5 +/- 3 mW/m in the westernmost zone III agree with predictions of standard oceanic lithospheric models for its estimated age of 126 Ma. In contrast, the heat flow within zone II is 5-15 mW/m higher than predicted. assuming that the mantle heat flow remains constant across the basin. This region of high values is coincident with the location of a major intra-crustal "S"-type reflector east of ODP Site 900. and the anomaly is consistent with the presence of 2-3 km of primarily upper continental crust above the reflector, with concentrations of radiogenic components similar to those from granodiorite samplles dredged off Galicia Bank. It is not, however, consistent with the low values of heat production measured on gabbroic sanhples from its western end at ODP Site 900. In zone I, detailed measurements across the tilted fault block south of ODP Site 901 show consistent variations which closely match predictions due to the effects of basement structure and sediment deposition. There is no evidence for variations due to vertical convective transport along the dipping basement fault block. Once corrected for these variations. measurements in zone I yield average values that agree quite well with previous measurements across Calicia Bank. indicating no systematic landward increase in heat flow with decreasing amounts of continental, extension.

Influence of sediment acidification and water flow on sediment acceptance and dispersal of juvenile soft-shell clams (Mya arenaria L.)

Although ocean acidification is expected to reduce carbonate saturation and yield negative impacts on open-ocean calcifying organisms in the near future, acidification in coastal ecosystems may already be affecting these organisms. Few studies have addressed the effects of sedimentary saturation state on benthic invertebrates. Here, we investigate whether sedimentary aragonite saturation (Omega aragonite) and proton concentration ([H+]) affect burrowing and dispersal rates of juvenile soft-shell clams (Mya arenaria) in a laboratory flume experiment. Two size classes of juvenile clams (0.5-1.5 mm and 1.51-2.5 mm) were subjected to a range of sediment Omega aragonite and [H+] conditions within the range of typical estuarine sediments (Omega aragonite 0.21-1.87; pH 6.8-7.8; [H+] 1.58 × 10**-8-1.51 × 10**- 7) by the addition of varying amounts of CO2, while overlying water pH was kept constant ~ 7.8 (Omega aragonite ~ 1.97). There was a significant positive relationship between the percent of juvenile clams burrowed in still water and Omega aragonite and a significant negative relationship between burrowing and [H+]. Clams were subsequently exposed to one of two different flow conditions (flume; 11 cm/s and 23 cm/s) and there was a significant negative relationship between Omega aragonite and dispersal, regardless of clam size class and flow speed. No apparent relationship was evident between dispersal and [H+]. The results of this study suggest that sediment acidification may play an important role in soft-shell clam recruitment and dispersal. When assessing the impacts of open-ocean and coastal acidification on infaunal organisms, future studies should address the effects of sediment acidification to adequately understand how calcifying organisms may be affected by shifting pH conditions.

Low-dimensional modeling of streaks in a wedge flow boundary layer

This paper is concerned with the low dimensional structure of optimal streaks in a wedge flow boundary layer, which have been recently shown to consist of a unique (up to a constant factor) three-dimensional streamwise evolving mode, known as the most unstable streaky mode. Optimal streaks exhibit a still unexplored/unexploited approximate self-similarity (not associated with the boundary layer self-similarity), namely the streamwise velocity re-scaled with their maximum remains almost independent of both the spanwise wavenumber and the streamwise coordinate; the remaining two velocity components instead do not satisfy this property. The approximate self-similar behavior is analyzed here and exploited to further simplify the description of optimal streaks. In particular, it is shown that streaks can be approximately described in terms of the streamwise evolution of the scalar amplitudes of just three one-dimensional modes, providing the wall normal profiles of the streamwise velocity and two combinations of the cross flow velocity components; the scalar amplitudes obey a singular system of three ordinary differential equations (involving only two degrees of freedom), which approximates well the streamwise evolution of the general streaks.

Performance of pressure control valves and flow meters precision in operational irrigation-water balance accuracy

In pressure irrigation-water distribution networks, pressure regulating devices for controlling the discharged flow rate by irrigation units are needed due to the variability of flow rate. In addition, applied water volume is used controlled operating the valve during a calculated time interval, and assuming constant flow rate. In general, a pressure regulating valve PRV is the commonly used pressure regulating device in a hydrant, which, also, executes the open and close function. A hydrant feeds several irrigation units, requiring a wide range in flow rate. In addition, some flow meters are also available, one as a component of the hydrant and the rest are placed downstream. Every land owner has one flow meter for each group of field plots downstream the hydrant. Its lecture could be used for refining the water balance but its accuracy must be taken into account. Ideal PRV performance would maintain a constant downstream pressure. However, the true performance depends on both upstream pressure and the discharged flow rate. The objective of this work is to asses the influence of the performance on the applied volume during the whole irrigation events in a year. The results of the study have been obtained introducing the flow rate into a PRV model. Variations on flow rate are simulated by taking into account the consequences of variations on climate conditions and also decisions in irrigation operation, such us duration and frequency application. The model comprises continuity, dynamic and energy equations of the components of the PRV.

Effect of type of dietary carbohydrates on digestion, intestinal barrier and growth performance in 25-d weaned rabbits

Los objetivos globales de esta tesis han sido estudiar el efecto que los carbohidratos de la dieta ejercen sobre los rendimientos productivos, la barrera intestinal, y la digestión de animales destetados a 25 días de edad. Además se ha estudiado cuál es el mejor periodo para determinar la digestibilidad fecal tras el destete a esta edad. En el primer experimento se estudió el efecto de la fibra neutro detergente soluble (FNDS) sobre la barrera intestinal, digestión, microbiota intestinal y rendimientos productivos de gazapos en gazapos en la fase post-destete. Se diseñaron tres piensos isonutritivos en los que la única fuente de variación fueron los niveles de fibra soluble. A partir de una dieta control (AH) con 103 g/kg de materia seca de FNDS y alfalfa como fuente principal de fibra, se sustituyó la mitad de esta alfalfa por una mezcla de pulpa de remolacha y pulpa de manzana (75:25) en el pienso B-AP y por una mezcla de cascarilla y concentrado de proteína de soja (88:12) en el pienso OH, obteniéndose 131 y 79 g/kg de FNDS sobre materia seca, respectivamente. Los conejos se destetaron a 25 días y fueron alimentados con los piensos experimentales hasta los 35 días de edad, momento en el que se sacrificaron para la determinación de la digestibilidad ileal aparente (DIA) de la materia seca (MS), proteína bruta (PB) y almidón, la morfología de la mucosa, y actividad enzimática en el yeyuno, el tejido linfoide asociado a la mucosa, así como la microbiota intestinal. Para la determinación de la morfología de la mucosa se utilizaron adicionalmente 19 animales lactantes de 35 días de edad. Para el estudio de la tasa de mortalidad, se utilizaron 118 animales más por tratamiento que recibieron los piensos experimentales durante las dos semanas post-destete y posteriormente un pienso comercial hasta los 60 días de edad. Los animales recibieron durante todo el experimento medicación en el agua de bebida (100 ppm de apramicina sulfato y 120 ppm de tilosina tartrato). El nivel de fibra soluble mejoró los parámetros que se utilizaron para la caracterización del estado de la barrera intestinal. Los conejos alimentados con el mayor nivel de FNDS en el pienso presentaron una mayor longitud de los villi (P=0.001), un mayor ratio longitud villi/profundidad de las criptas (8.14; P=0.001), una mayor actividad disacaridásica (8671 μmol de glucosa/g de proteína; P=0.019), así como una mayor digestibilidad ileal (96.8%; P=0.002), observándose una reducción en el flujo ileal de almidón a medida que se incrementó el nivel de fibra soluble en el pienso (1,2 vs 0,5 g/d; P=0.001). Los animales lactantes a 35 días de edad presentaron un ratio longitud de villi/profundidad de las criptas menor que el observado en aquéllos alimentados con el pienso B-AP (6.70), pero superior al de los piensos AH y OH. Niveles inferiores de NDFS tendieron (P=0.074) a incrementar la respuesta inmune de tipo celular (linfocitos CD8+). El pienso también afectó a la producción de IL2 (CD25+; P=0.029; CD5+CD25+; P=0.057), pero sin llegar a establecerse una clara relación con el nivel de fibra soluble. La diversidad de la microbiota intestinal no se vio afectada por el pienso (P ≥ 0.38). Los animales alimentados con las piensos B-AP y AH presentaron una reducción en la frecuencia de detección de Clostridium perfringens tanto en íleon (P=0.062) como en ciego (4.3 vs. 17.6%, P =0.047), comparado con el pienso OH. Además la tasa de mortalidad (118 gazapos/pienso) disminuyó de 14.4% en el pienso OH a 5.1% en el pienso B-AP. Entre los 32 y los 35 días de edad se determinó la digestibilidad fecal aparente (14/pienso) de la materia seca (MS), energía bruta (EB), proteína bruta (PB), fibra neutro detergente (FND), fibra ácido detergente (FAD) y almidón. Este grupo, junto con otros nueve animales por tratamiento se utilizaron para determinar el peso del estómago y el ciego, la concentración cecal de ácidos grasos volátiles (AGV) y amoniaco (NH3), así como las tasas de similitud de la microbiota intestinal. Además se estudiaron los rendimientos productivos (35 animales/tratamiento) de los gazapos durante todo el período de cebo, consumiendo los piensos experimentales desde el destete hasta los 35 días y posteriormente un pienso comercial hasta los 60 días de edad. Niveles crecientes de FNDS mejoraron la digestibilidad fecal de la materia seca (MS) y energía (P<0.001). La inclusión FNDS aumentó de manera lineal el peso del contenido cecal (P=0.001) y el peso del aparato digestivo completo (P=0.008), y en los días previos al sacrificio disminuyó de manera lineal el consumo medio diario (P=0.040). Se observó además, una disminución lineal (P≤0.041) del pH del estómago. No se encontró relación entre el pH, la concentración y proporciones molares de AGV y el nivel de FNDS. El pienso pareció tener un efecto, incluso superior al de la madre, sobre la tasa de similitud de la microbiota, y los efectos fueron mayores a nivel cecal que ileal. La eficacia alimenticia aumentó de manera lineal en un 12% entre piensos extremos tras el destete (25- 39d) y en un 3% en el período global de cebo con niveles mayores de NDFS. El consumo medio diario durante la fase post-destete y durante todo el período de cebo, tendió a aumen tar (P≤0.079) con niveles mayores de FNDS, sin embargo no se apreció efecto sobre la ganancia media diaria (P≥0.15). En conclusión, el incremento del nivel de fibra soluble en el pienso parece resultar beneficioso para la salud del animal ya que mejora la integridad de la mucosa, y reduce la frecuencia de detección de potenciales patógenos como C. perfringens y Campylobacter spp. Conforme a estos resultados, debería tenerse en cuenta el contenido en fibra soluble en la formulación de piensos de conejos en la fase post-destete. El objetivo del segundo experimento fue determinar el efecto de la fuente de almidón sobre la digestión, la microbiota intestinal y los rendimientos productivos en conejos destetados con 25 días de edad. Se formularon tres piensos isonutritivos en los que se modificaron las principales fuentes de almidón: trigo crudo, trigo cocido y una combinación de trigo y arroz cocido. Dos grupos de 99 y 193 animales se destetaron con 25 días de edad. El primero de ellos se utilizó para la determinación de los parámetros productivos conforme al mismo protocolo seguido en el experimento anterior. El segundo de los grupos se utilizó para la determinación de la digestibilidad fecal de 32 a 35 d, la digestibilidad ileal aparente (DIA) a 35 d, la morfología de la mucosa intestinal, los parámetros de fermentación cecal; así como, la caracterización de la microbiota intestinal. Se utilizaron además dos grupos adicionales de animales 384 (medicados) y 177 (no medicados) para estudiar el efecto de la suplementación con antibióticos en el agua de bebida sobre la mortalidad. El procesado térmico del trigo mejoró ligeramente la digestibilidad ileal del almidón (P=0.020) pero no modificó el flujo final de almidón que alcanzó el ciego, observándose una mayor frecuencia de detección de Campylobacter spp. y Ruminococcus spp. en ciego (P≤0.023), pero sin cambios a nivel ileal. El procesado térmico del trigo no afectó tampoco a los parámetros productivos, la mortalidad, la digestibilidad ileal y fecal o la morfología de la mucosa. La sustitución parcial del trigo cocido por arroz cocido, penalizó la digestibilidad ileal del almidón (P=0.020) e incrementó el flujo ileal de este nutriente al ciego (P=0.007). Sin embargo no afectó a la mortalidad, pese a que se detectaron cambios en la microbiota tanto a nivel ileal como cecal, disminuyendo la frecuencia de detección de Campylobacter spp. (en íleon y ciego), Helicobacter spp. (en íleon) y Ruminococcus spp (en ciego) e incrementando Bacteroides spp. (en ciego) (P≤0.046). El empleo de arroz cocido en las piensos post-destete no tuvieron efectos sobre los parámetros productivos, la mortalidad, la digestibilidad ileal y fecal a excepción del almidón, o la morfología de la mucosa. La suplementación con antibiótico redujo la fre cuencia de detección de la mayoría de las bacterias estudiadas (P≤0.048), sobre todo para Campylobacter spp., Clostridium perfringens y Propionibacterium spp. (P≤0.048), observándose un efecto mayor a nivel ileal que cecal, lo que se asoció a la bajada significativa (P<0.001) de la mortalidad. En conclusión, los resultados de este experimento indican que la fuente de almidón afecta a la microbiota intestinal pero no influiye sobre la salud del animal. En relación al procesado, el uso de trigo cocido junto con arroz cocido no mejora los resultados obtenidos con trigo duro, si bienserían necesarios más experimentos que confirmaran este punto. El último de los experimentos se centró en un aspecto metodológico. Dado que, los conejos destetados presentan un patrón digestivo diferente al de un animal adulto resultado de su inmadurez digestiva, el objetivo buscado era tratar de determinar el mejor procedimiento para la determinación de la digestibilidad fecal en los gazapos en la fase post-destete. Para tal fin se utilizaron 15 animales/tratamiento de tres camadas diferentes que se destetaron con 25 días, suministrándoles un pienso comercial de crecimiento-cebo. Se registró el consumo medio diario y la excreción diaria de heces desde el día 25 hasta el día 40 de edad para la determinación de la digestibilidad de la MS. La camada afectó al consumo medio diario y la excreción de heces (P=0.013 y 0.014, respectivamente), observándose una tendencia (P=0.061) en la digestibilidad. La edad afectó (P<0.001) a todos estos factores, incrementándose de manera más evidente la excreción que la ingestión de materia seca en la primera semana de vida, para aumentar de forma paralela a partir de la segunda. La correlación entre el consumo medio diario fue mayor con la excreción de heces del mismo día que con la del día siguiente, por lo que se utilizó el primero para la determinación de la digestibilidad de la MS (MSd). La MSd disminuyó de manera lineal hasta los 32 días de edad (2.17±0.25 unidades porcentuales por día), mientras que permaneció constante desde los 32 a los 40 días (69.4±0.47%). Por otro lado, la desviación estándar de la MSd se redujo cuando se incrementó el período de recogida de 2 a 6 días en un 54%. Conforme a los resultados obtenidos, se puede concluir que no es aconsejable comenzar las pruebas de digestibilidad antes de los 32 días de edad y que el número de animales necesario para detectar diferencias significativas entre tratamientos dependerá del período de recogida de heces. ABSTRACT The global aim of this thesis has been to study the effect of dietary carbohydrates on growth, performance, digestion and intestinal barrier in 25-d weaned rabbits. In addition there has also been studied which is the best period to determine the fecal digestibility after weaning. The first experiment focused on the effect of Neutral Detergent Soluble Fibre (NDSF) on gut barrier function, digestion, intestinal microbiota and growth performance n rabbits in the post-weaning period. Three isonutritive diets which only varied in the levels of soluble fiber were formulated such as it described as follows: a control diet (AH) containing 103 g of neutral detergent soluble fiber, including alfalfa as main source of fiber, was replaced by a mixture of beet and apple pulp (75-25) in the B-AP diet and, by a mix of oat hulls and soybean protein concentrate (88:12) in the OH diet, resulting 131 and 79 g of NDFS/kg of dry matter, respectively. Rabbits, weaned at 25 days of age, were fed the experimental diets up to 35 days of age, moment in which they were slaughtered for apparent ileal digestibility (AID) of dry matter (DM), crude protein (CP) and starch, mucosa morphology, sucrose activity, characterization of lamina propria lymphocytes and intestinal microbiota. To assess mucosal morphology, 19 suckling 35-d-old rabbits were also used. For mortality study, besides these animals, 118 additional rabbits per treatment were fed the experimental diets for two weeks period and thereafter received a commercial diet until 60 days of age. Rabbits were water medicated during the whole experimental period (100 ppm de apramicine sulphate and 120 ppm of tylosine tartrate). Level of soluble fiber improved all the parameters used for the characterization of the intestinal barrier condition. Villous height of the jejunal mucosa increased with dietary soluble fiber (P=0.001). Villous height of jejunal mucosa increased with dietary soluble fiber (P = 0.001). Rabbits fed the highest level of soluble fiber (BA-P diet) showed the highest villous height/crypth depth ratio (8.14; P = 0.001), sucrase specific activity (8671 μmol glucose/ g protein; P = 0.019), and the greatest ileal starch digestibility (96.8%; P = 0.002). The opposite effects were observed in rabbits fed decreased levels of soluble fiber (AH and OH diets; 4.70, 5,848 μmol of glucose/g of protein, as average, respectively). The lowest ileal starch digestibility was detected for animal fed OH diet (93.2%). Suckling rabbits of the same age showed a lower villous height/crypt depth ratio (6.70) compared with the B-AP diet group, but this ration was higher that the AH or OH diet groups. Lower levels of soluble fiber tended (P = 0.074) to increase the cellular immune response (CD8+ lymphocytes). Diet affected IL-2 production (CD25+, P = 0.029; CD5+CD25+, P = 0.057), with no clear relationship between soluble fiber and IL-2. The intestinal microbiota biodiversity was not affected by diets (P ≥ 0.38). Animals fed B-AP and AH diets had a reduced cecal frequency of detection compatible with Campylobacter spp. (20.3 vs. 37.8, P = 0.074), and Clostridium perfringens (4.3 vs. 17.6%, P = 0.047), compared with the OH diet group. Moreover, the mortality rates decreased from 14.4 (OH diet) to 5.1% (B-AP diet) with the increased presence of soluble fiber in the diet. Between 32 and 35 days of age, faecal apparent digestibility of dry matter (DM), gross energy (GE), crude protein (CP), neutral detergent fiber (NDF), acid detergent fiber (ADF) and starch was determined (14/diet). This group, plus another nine rabbits/diet were used to determine weight of stomach and caecum and their contents, cecal fermentation traits and similarity rate (SR) of intestinal microbiota. Besides, growth performance parameters (35 rabbits/diet) were studied during the whole fattening period, in animals consuming the experimental feed after the weaning up to 35 days of age and later on a commercial diet up animals reached 60 days of age. Increasing levels of Neutral Detergent Soluble Fiber improved faecal dry matter and energy digestibility (P<0.001). NDSF inclusion improved linearly weight of the caecal content (P=0.001) and the total gastrointestinal tract (P=0.008), and in the previous days to slaughter a linear decrease of daily feed intake in diet with highest level of soluble fiber was also observed. Stomach pH decreased linearly with increasing levels of NDFS (P≤0.041). No relation between NDSF level on pH, concentration and molar proportion of VFA was found. Treatments appeared to influence the similarity rate of microbiota, even higher to mother effect. These effects were higher in ileum than in caecum. A linear positive effect of feed efficiency was observed, which increased around 12% in the two weeks post-weaning (25-39d) and 3% in the whole fattening period between extreme diets with highest levels of soluble fiber. Average daily feed intake during the two weeks after weaning and in the whole fattening period, tended (P≤0.079) to increase with highest levels of NDSF; although there were no effect on daily weight gain (≥0.15). In conclusion, an increase of soluble fiber in the feed seems to be beneficial for animal health, due to improve mucose integrity and reduce detection frequency of those poten tial pathogens like C. perfringens and Campylobacter spp. According to these results, level of soluble fiber should be taking care in feed rabbit formulation in the post-weaning period. The objective of the second experiment was to determine the effect of source of starch on digestion, intestinal microbiota and growth performance in twenty-five-day old weaned rabbits. To accomplish with this aim three iso-nutritive diets were formulated with different source of starch: raw wheat, boiled wheat and a combination of boiled wheat and boiled rice. Two groups of 99 and 193 rabbits were weaned at 25 days of age. The first group was used for growth performance determination following the same protocol than in previous experiment. The second group was used to determine faecal digestibility from 32 to 35 d, apparent ileal digestibility (AID) at 35 d, jejunal mucosa morphology, caecal fermentation traits and characterization of intestinal microbiota. For mortality, two additional groups of 384 (medicated) and 177 (not medicated) were used in order to study the effect of antibiotic water supply supplementation. Heat processing of starch slightly improved ileal digestibility of starch (P=0.020) but did not modify the flow of starch to the caecum. An increase in frequency of detection of Campylobacter spp. y Ruminococcus spp. was observed in the caecum (P≤0.023), with no changes at ileal level. Heat processing of wheat did not modify growth performance, mortality, ileal or faecal digestibility and mucosa morphology. Partial substitution of boiled wheat for boiled rice in the diet impaired ileal starch digestibility (P=0.020) and increased the ileal flow of this nutrient to the caecum (P=0.007). However, it did not affect mortality rate, although changes in the ileal and caecal intestinal microbiota were detected, decreasing the frequency of detection of Campylobacter spp. (both ileum and caecum), Helicobacter spp. (at ileum) and Ruminococcus spp (at caecum) and increasing the Bacteroides spp. (at caecum) (P≤0.046). The effect of boiled rice supplementation did not alter growth performance, mortality, ileal or faecal digestibility of other nutrients than starch, and mucosa morphology. Medication of rabbits reduced the ileal frequency of detection of most bacteria studied (P≤0.048), especially for Campylobacter spp., Clostridium perfringens y Propionibacterium spp. (P≤0.048), resulting the effect higher at ileal than caecal level and relating it with a strong reduction of mortality rate (P<0.001). In conclusion, the results of this experiment make think that the source of starch affects the intestinal microbiota but they do not seem to influence animal health. In relation to the effect of heat processed the use of cooked wheat or cooked rice it does not seem to im prove the results obtained with hard wheat, but there would be necessary more experiments that were confirming this point. The last experiment focused on a methodological aspect. Considering that, weaned rabbits have a different digestive pattern than older animals due to their digestive immaturity; the fixed objective was to determine the best procedure for faecal digestibility determination in young rabbits in the post-weaning period. Fifteen rabbits from 5 different litters were weaned at 25 days of age and fed with a commercial feed. Feed intake and faeces excretion were recorded daily from 25 to 40 days of age for dry matter digestibility (DMd) determination. Litter affected daily DM intake and excretion (P=0.013 y 0.014, respectively) and tended to affect DMd (P=0.061). Age affected all these factors (P<0.001), but ingestion increased slowly than dry matter excretion during the first week buth they evolved similarly in the second week. The correlation between daily feed intakes was higher with the faeces excretion of the day than with faeces excretion of the next day, and the first values were used to determine daily DMd. The DMd decreased linearly from weaning to 32 d of age (2.17±0.25 percentage units per day), whereas from 32 to 40 d remained constant (69.4±0.47%). On the other hand, average standard deviation of DMd decreased by 54% when the length of collection period increased from 2 to 6d. Consequently to the obtained results, it could be concluded that it would not be advisable to start digestibility trials before the 32 days of age and that the number of animals required to detect a significant difference among means would depend on the collection period.

Analytical Calculation of Stall-inception and Surge Points for an Axial-flow Compresor Rotor

Recently, a theoretical criterion to calculate the stability of an axial-flow compressor rotor has been presented in the scientific literature. This theoretical criterion was used for determining the locus of the stability line over the rotor map and for predicting the post-stall evolution of the constant-speed line of a rotor. The main objective of this paper is to improve the predictions of such a model. To do that, the paper proposes a different characterization of the characteristic azimuthal length and a calculation of the ratio of specific heats based on a polytropic exponent. Thanks to these new values, the model predicts two bifurcation points in the behaviour of the flow: the inception point of the instability and the surge point. Experimental data from a pure axial compressor are used to validate the model showing that the prediction of the flow coefficient at the surge point has an error inferior to 5%. For the rotor studied, the paper provides a quantitative and qualitative description of the inception of the instability and of the mechanism involved in the instable region of the compressor map. The paper also discusses the role of rotor efficiency in the position of the bifurcations and gives a sensitivity analysis of its position. Finally, it presents a discussion about how the model can explain the different behaviours exhibited by the same rotor when the flow coefficient is reduced

Quasi-cylindrical approximation to the swirling flow in an atomizer chamber

A quasi-cylindrical approximation is used to analyse the axisymmetric swirling flow of a liquid with a hollow air core in the chamber of a pressure swirl atomizer. The liquid is injected into the chamber with an azimuthal velocity component through a number of slots at the periphery of one end of the chamber, and flows out as an anular sheet through a central orifice at the other end, following a conical convergence of the chamber wall. An effective inlet condition is used to model the effects of the slots and the boundary layer that develops at the nearby endwall of the chamber. An analysis is presented of the structure of the liquid sheet at the end of the exit orifice, where the flow becomes critical in the sense that upstream propagation of long-wave perturbations ceases to be possible. This nalysis leads to a boundary condition at the end of the orifice that is an extension of the condition of maximum flux used with irrotational models of the flow. As is well known, the radial pressure gradient induced by the swirling flow in the bulk of the chamber causes the overpressure that drives the liquid towards the exit orifice, and also leads to Ekman pumping in the boundary layers of reduced azimuthal velocity at the convergent wall of the chamber and at the wall opposite to the exit orifice. The numerical results confirm the important role played by the boundary layers. They make the thickness of the liquid sheet at the end of the orifice larger than predicted by rrotational models, and at the same time tend to decrease the overpressure required to pass a given flow rate through the chamber, because the large axial velocity in the boundary layers takes care of part of the flow rate. The thickness of the boundary layers increases when the atomizer constant (the inverse of a swirl number, proportional to the flow rate scaled with the radius of the exit orifice and the circulation around the air core) decreases. A minimum value of this parameter is found below which the layer of reduced azimuthal velocity around the air core prevents the pressure from increasing and steadily driving the flow through the exit orifice. The effects of other parameters not accounted for by irrotational models are also analysed in terms of their influence on the boundary layers.

(Table 1) Summary of basalt unit thickness, vesicularity, number of flow units, and average porosity at ODP Site 135-839

An inflatable drill-string packer was used at Site 839 to measure the bulk in-situ permeability within basalts cored in Hole 839B. The packer was inflated at two depths, 398.2 and 326.9 mbsf; all on-board information indicated that the packer mechanically closed off the borehole, although apparently the packer hydraulically sealed the borehole only at 398.2 mbsf. Two pulse tests were run at each depth, two constant-rate injection tests were run at the first set, and four were run at the second. Of these, only the constant-rate injection tests at the first set yielded a permeability, calculated as ranging from 1 to 5 * 10**-12 m**2. Pulse tests and constant-rate injection tests for the second set did not yield valid data. The measured permeability is an upper limit; if the packer leaked during the experiments, the basalt would be less permeable. In comparison, permeabilities measured at other Deep Sea Drilling Project and Ocean Drilling Program sites in pillow basalts and flows similar to those measured in Hole 839B are mainly about 10**-13 to 10**-14 m**2. Thus, if our results are valid, the basalts at Site 839 are more permeable than ocean-floor basalts investigated elsewhere. Based on other supporting evidence, we consider these results to be a valid measure of the permeability of the basalts. Temperature data and the geochemical and geotechnical properties of the drilled sediments all indicate that the site is strongly affected by fluid flow. The heat flow is very much less than expected in young oceanic basalts, probably a result of rapid fluid circulation through the crust. The geochemistry of pore fluids is similar to that of seawater, indicating seawater flow through the sediments, and sediments are uniformly underconsolidated for their burial depth, again indicating probable fluid flow. The basalts are highly vesicular. However, the vesicularity can only account for part of the average porosity measured on the neutron porosity well log; the remainder of the measured porosity is likely present as voids and fractures within and between thin-bedded basalts. Core samples, together with porosity, density, and resistivity well-log data show locations where the basalt section is thin bedded and probably has from 15% to 35% void and fracture porosity. Thus, the measured permeability seems reasonable with respect to the high measured porosity. Much of the fluid flow at Site 839 could be directed through highly porous and permeable zones within and between the basalt flows and in the sediment layer just above the basalt. Thus, the permeability measurements give an indication of where and how fluid flow may occur within the oceanic crust of the Lau Basin.

Effect of inspiratory flow on methacholine challenge in children

Regulation of inspiratory flow alters the outcomes of the methacholine (MHC) challenge in adults and cough receptor sensitivity in children. The effect of inspiratory flow on the reproducibility of the MHC challenge in children is unknown. The aim of this study was to evaluate the effect of inspiratory flow alteration on the repeatabilty of the MHC challenge in children with and without asthma. Twenty-five children undertook the MHC challenge on three different days by using a dosimeter connected to a setup that allowed regulation of inspiratory flow and pattern. Children were randomized to commence the challenges at 20 or 60 L/min, and the last challenge was performed at 20 L/min. The within-subject standard deviation, 95% range for change, and doubling dose for the differing inspiratory flow (20 vs. 60 L/min) was more than twice that of when inspiratory flow was maintained at 20 L/min for both occasions. The range of the limits of agreement of the Bland and Altman plot was smaller when inspiratory flow was constant. For short-term comparative individual studies in children, inspiratory flow should be regulated. Laboratories and research measuring change in airway hyperrepsonsiveness to MHC should determine and report reproducibility indices of the challenge so airway hyperresponsiveness changes can be interpreted meaningfully.

Study of flow behaviour in a three-product cyclone using computational fluid dynamics

Simplicity in design and minimal floor space requirements render the hydrocyclone the preferred classifier in mineral processing plants. Empirical models have been developed for design and process optimisation but due to the complexity of the flow behaviour in the hydrocyclone these do not provide information on the internal separation mechanisms. To study the interaction of design variables, the flow behaviour needs to be considered, especially when modelling the new three-product cyclone. Computational fluid dynamics (CFD) was used to model the three-product cyclone, in particular the influence of the dual vortex finder arrangement on flow behaviour. From experimental work performed on the UG2 platinum ore, significant differences in the classification performance of the three-product cyclone were noticed with variations in the inner vortex finder length. Because of this simulations were performed for a range of inner vortex finder lengths. Simulations were also conducted on a conventional hydrocyclone of the same size to enable a direct comparison of the flow behaviour between the two cyclone designs. Significantly, high velocities were observed for the three-product cyclone with an inner vortex finder extended deep into the conical section of the cyclone. CFD studies revealed that in the three-product cyclone, a cylindrical shaped air-core is observed similar to conventional hydrocyclones. A constant diameter air-core was observed throughout the inner vortex finder length, while no air-core was present in the annulus. (c) 2006 Elsevier Ltd. All rights reserved.

Flow patterns and performance of distillation trays

It is known that distillation tray efficiency depends on the liquid flow pattern, particularly for large diameter trays. Scale·up failures due to liquid channelling have occurred, and it is known that fitting flow control devices to trays sometirr.es improves tray efficiency. Several theoretical models which explain these observations have been published. Further progress in understanding is at present blocked by lack of experimental measurements of the pattern of liquid concentration over the tray. Flow pattern effects are expected to be significant only on commercial size trays of a large diameter and the lack of data is a result of the costs, risks and difficulty of making these measurements on full scale production columns. This work presents a new experiment which simulates distillation by water cooling. and provides a means of testing commercial size trays in the laboratory. Hot water is fed on to the tray and cooled by air forced through the perforations. The analogy between heat and mass transfer shows that the water temperature at any point is analogous to liquid concentration and the enthalpy of the air is analogous to vapour concentration. The effect of the liquid flow pattern on mass transfer is revealed by the temperature field on the tray. The experiment was implemented and evaluated in a column of 1.2 m. dia. The water temperatures were measured by thennocouples interfaced to an electronic computerised data logging system. The "best surface" through the experimental temperature measurements was obtained by the mathematical technique of B. splines, and presented in tenos of lines of constant temperature. The results revealed that in general liquid channelling is more imponant in the bubbly "mixed" regime than in the spray regime. However, it was observed that severe channelling also occurred for intense spray at incipient flood conditions. This is an unexpected result. A computer program was written to calculate point efficiency as well as tray efficiency, and the results were compared with distillation efficiencies for similar loadings. The theoretical model of Porter and Lockett for predicting distillation was modified to predict water cooling and the theoretical predictions were shown to be similar to the experimental temperature profiles. A comparison of the repeatability of the experiments with an errors analysis revealed that accurate tray efficiency measurements require temperature measurements to better than ± 0.1 °c which is achievable with conventional techniques. This was not achieved in this work, and resulted in considerable scatter in the efficiency results. Nevertheless it is concluded that the new experiment is a valuable tool for investigating the effect of the liquid flow pattern on tray mass transfer.

Hydrodynamic modeling of mineral wool fiber suspensions in a two-dimensional channel flow

A consequence of a loss of coolant accident is the damage of adjacent insulation materials (IM). IM may then be transported to the containment sump strainers where water is drawn into the ECCS (emergency core cooling system). Blockage of the strainers by IM lead to an increased pressure drop acting on the operating ECCS pumps. IM can also penetrate the strainers, enter the reactor coolant system and then accumulate in the reactor pressure vessel. An experimental and theoretical study that concentrates on mineral wool fiber transport in the containment sump and the ECCS is being performed. The study entails fiber generation and the assessment of fiber transport in single and multi-effect experiments. The experiments include measurement of the terminal settling velocity, the strainer pressure drop, fiber sedimentation and resuspension in a channel flow and jet flow in a rectangular tank. An integrated test facility is also operated to assess the compounded effects. Each experimental facility is used to provide data for the validation of equivalent computational fluid dynamic models. The channel flow facility allows the determination of the steady state distribution of the fibers at different flow velocities. The fibers are modeled in the Eulerian-Eulerian reference frame as spherical wetted agglomerates. The fiber agglomerate size, density, the relative viscosity of the fluid-fiber mixture and the turbulent dispersion of the fibers all affect the steady state accumulation of fibers at the channel base. In the current simulations, two fiber phases are separately considered. The particle size is kept constant while the density is modified, which affects both the terminal velocity and volume fraction. The relative viscosity is only significant at higher concentrations. The numerical model finds that the fibers accumulate at the channel base even at high velocities; therefore, modifications to the drag and turbulent dispersion forces can be made to reduce fiber accumulation.