The occurrence of defensive alkaloids in non-integumentary tissues of the Brazilian red-belly toad Melanophryniscus simplex (Bufonidae)

The red-belly toads (Melanophryniscus) of southern South America secrete defensive alkaloids from dermal granular glands. To date, all information on Melanophryniscus alkaloids has been obtained by extraction from either skins or whole organisms; however, in other amphibians, tetrodotoxins, samandarines, and bufadienolides have been detected in both skin and other organs, which raise the possibility that lipophilic alkaloids may occur in non-integumentary tissues in Melanophryniscus as well. To test this hypothesis, we studied the distribution of alkaloids in the skin, skeletal muscle, liver, and mature oocytes of the red-belly toad M. simplex from three localities in southern Brazil. Gas chromatography and mass spectrometry of skin extracts from 11 individuals of M. simplex resulted in the detection of 47 alkaloids (including isomers), 9 unclassified and 38 from 12 known structural classes. Each alkaloid that was present in the skin of an individual was also present in the same relative proportion in that individual's skeletal muscle, liver, and oocytes. The most abundant and widely distributed alkaloids were the pumiliotoxins 251D, 267C, and 323A, 5,8-disubstituted indolizidines 207A and 223D, 5,6,8-trisubstituted indolizidine 231B, 3,5-disubstituted pyrrolizidines cis-223B and cis- and trans-251K, and izidine 211C. We report the first record of piperidines in Melanophryniscus, bringing the total number of alkaloid classes detected in this genus to 16. Alkaloid composition differed significantly among the three study sites. The functional significance of defensive chemicals in non-integumentary tissues is unknown.

Behavioral analysis of the interaction between the spitting spider Scytodes globula (Araneae: Scytodidae) and the harvestman Discocyrtus invalidus (Opiliones: Gonyleptidae)

Spitting spiders (Scytodidae) have a distinct predatory strategy in which they eject a sticky secretion from their cheliceral fangs to immobilize prey. This behavior could potentially allow the spider not only to avoid defensive secretions but also to bite specific vulnerable spots of a potential prey such as a harvestman. We used an ethogram, a fluxogram and an experiment to analyze the interaction between the harvestman Discocyrtus invalidus Piza 1938 (Arachnida: Opiliones) and the syntopic spider Scytodes globula (Nicolet 1849) (Arachnida: Araneae). These spiders, while readily taking crickets as prey, seldom spat at and never bit the harvestmen, which apparently did not exude repugnatorial secretions. We therefore tested, by clogging the glands and using appropriate controls, whether non-visible amounts of secretions could cause the rejection, but the harvestmen were still refused. This is the first detailed and quantified description of an interaction between a spitting spider and a harvestman. The general conclusions are that S. globula avoids preying on D. invalidus, S. globula behaves differently when attacking harvestmen and crickets and the scent gland secretions of D. invalidus do not play a direct role in this predator-prey interaction.

Einfluss von oxidativem Stress auf die DNA-Reparatur in Säugerzellen

Gegenstand dieser Arbeit war es, das Zusammenspiel zwischen DNA-Reparatur und zellulärem anitoxidativen Abwehrsystem in Melanomzellen und gesunden Hautfibroblasten näher zu untersuchen. Dabei konnte gezeigt werden, dass die dominierenden DNA-Läsionen im Falle einer Bestrahlung mit sichtbarem Licht (400 – 800 nm) Fpg-sensitive Läsionen, zu denen die Basenmodifikation 7,8-Dihydro-8-oxoguanin (8-oxoG) gehört, und im Falle der UVA-Bestrahlung Cyclobutan-Pyrimidindimere (CPDs) sind. Sowohl Melanomzellen als auch Hautfibroblasten waren problemlos in der Lage, die durch sichtbares Licht und UVA-Strahlung induzierten oxidativen DNA-Modifikationen zu reparieren. Jedoch reagierten Melanomzellen in einer adaptiven Antwort mit einer Erhöhung ihres Glutathion-Gehalts auf ein Maximum (nach circa 10 - 14 h) nach Bestrahlung mit sichtbarem Licht, wohingegen die Hautfibroblasten einen massiven Einbruch direkt nach Bestrahlung und eine extrem lange Erholungsphase über 48 h aufzuweisen hatten. Die darauffolgende Untersuchung der DNA-Reparaturkapazität der Zellen unter Bedingungen von oxidativem Stress mit vorangegangener Depletion intrazellulären Glutathions zeigten eine dramatische, nahezu vollständige Hemmung der Reparatur durch UVA- bzw. Sonnenlicht-induzierter Fpg-sensitiver DNA-Modifikationen (8-oxoG) - sowohl in Melanomzellen als auch in Hautfibroblasten. Dieser Effekt ließ sich durch den Zusatz von Dithiothreitol (DTT), nach erfolgter Bestrahlung der Glutathion-depletierten Zellen, wieder komplett revertieren. Diese Ergebnisse weisen darauf hin, dass an der Reparatur ein redoxempfindliches Protein oder zellulärer Cofaktor beteiligt sein muß. Zudem konnte durch Untersuchungen der Nukleotidexzisionsreparatur (NER) und der Einzelstrangbruchreparatur nach dem gleichen Versuchsdesign gezeigt werden, dass es sich hierbei sehr wahrscheinlich um einen für die Basenexzisionsreparatur (BER) von 7,8-dihydro-8-oxo-guanine (8-oxoG) exklusiven Effekt handelte. Zwei der wichtigsten Reparaturproteine der BER, nämlich hOGG1 und APE1, wurden anschließend auf ihre Funktionsfähigkeit hin untersucht, da es naheliegend war, dass der Reparaturhemmung ein Funktionsverlust eines dieser beiden Enzyme zugrunde liegen könnte. Im Falle des APE1-Proteins konnte dies ausgeschlossen werden, da mit Hilfe der Alkalischen Elution die volle Funktionsfähigkeit für die Reparatur von AP-Läsionen nachgewiesen werden konnte. Interessanterweise zeigte aber das hOGG1-Protein eine zwischen der dritten und vierten Stunde nach Bestrahlung Glutathion-depletierter Zellen stark abfallende Aktivität der 8-oxoG-Glykosylasefunktion. Die Western-Blot-Analyse ergab allerdings keinen Hinweis auf eine Proteinoxidation von hOGG1. Möglicherweise wird nicht hOGG1 selbst, wohl aber ein anderes, für eine konzertierte Abfolge der einzelnen Reparaturschritte entscheidend notwendiges Protein innerhalb der Zelle durch ROS leicht oxidiert. In jedem Fall bleibt festzustellen, dass Glutathion eine wichtige Aufgabe hinsichtlich einer voll funktionsfähigen Basenexzisionreparatur zuzukommen scheint. Die Ergebnisse unterstreichen die mögliche Bedeutung von oxidativem Stress für die Entstehung von Krebs durch Sonnenlicht, insbesondere durch UVA, da die durch die Strahlung (und eventuell auftretende Entzündung) gebildeten ROS nicht nur DNA-Schäden induzieren, sondern auch ihre Reparatur verhindern können.

Einfluss von Resveratrol auf oxidative DNA-Schäden und Mutagenese in vivo

Oxidative DNA-Basenmodifikationen, wie 7,8-Dihydro-8-oxoguanin (8-oxoG), werden endogen in allen Zellen gebildet. Die beobachtbaren Spiegel ergeben sich aus dem Gleichgewicht zwischen der Bildung durch reaktive Sauerstoffspezies (ROS), sowie der gleichzeitigen Reparatur der DNA-Schäden. Durch ihr hohes mutagenes Potential, tragen oxidative DNA-Basenmodifikationen zur spontanen Mutationsrate bei. Der Ausfall wichtiger DNA-Reparaturmechanismen führt in Ogg1(-/-)Csb(-/-)-Knockout-Mäusen zu einem Anstieg von 8 oxoG und der spontanen Mutationsrate.rnIn dieser Arbeit sollte untersucht werden, ob die basalen Spiegel an oxidativen Basenmodifikationen und die spontanen Mutationsraten in vivo durch die orale Gabe von Resveratrol moduliert werden können. Resveratrol ist ein Pflanzeninhaltsstoff (u.a. aus Rotwein) mit einer Vielzahl von Wirkungen, der bereits in zahlreichen Studien ein chemopräventives Potential gezeigt hat und antioxidativ wirkt.rnAn verschiedenen Mausgenotypen wurden zum einen eine Kurzzeit-Behandlung (7 Tage mit 100 mg/kg per Gavage) und zum anderen eine Langzeit-Behandlung (3-9 Monate mit 0,04% ad libitum) mit Resveratrol durchgeführt. Die oxidativen DNA Schäden wurden in primären Maushepatozyten mit Hilfe einer modifizierten Alkalischen Elution, mit der bakteriellen Formamidopyrimidin-DNA Glykosylase als Sonde, bestimmt. Zur Analyse der Mutationsrate wurde der BigBlue® Mutationsassay mit anschließender Sequenzierung der Mutationen verwendet.rnDie Ergebnisse zeigen, dass die Kurzzeit- und die Langzeit-Behandlung mit Resveratrol die basalen Spiegel oxidativer DNA-Basenmodifikationen senken. Die Reduktion ist jeweils wesentlich ausgeprägter in den reparaturdefizienten Ogg1(-/-)Csb(-/-)-Mäusen zu erkennen. Auch die spontane Mutationsrate wird durch eine mehrmonatige Behandlung mit Resveratrol um ungefähr 20-30% reduziert.rnAnschließende mechanistische Untersuchungen zeigten, dass dieser Schutz wahrscheinlich auf einer Induktion der antioxidativen Schutzmechanismen begründet ist. So wurde gefunden, dass primäre Hepatozyten aus mit Resveratrol behandelten Mäusen wesentlich besser gegen exogen herbeigeführten oxidativen Stress geschützt sind, als Hepatozyten von unbehandelten Tieren. Ein weiterer Hinweis ist die Hochregulation der mRNA-Spiegel von verschiedenen antioxidativen Schutzenzymen, wie Superoxiddismutase 1 / 2, Hämoxygenase 1, Glutathionperoxidase 1, nach der Gabe von Resveratrol in Mäuselebern. Außerdem sind die oxidativen Markermutationen (GC->TA-Transversionen) stärker von der Reduktion der spontanen Mutationsrate betroffen, als andere Mutationen (z.B. GC->AT-Transitionen).rnDie Ergebnisse zeigen erstmalig, dass spontane Mutationen in vivo durch Fremdstoffe in der Nahrung reduziert werden können. Im Falle von Resveratrol wird diese Reduktion wahrscheinlich durch eine Stimulation der antioxidativen Schutzmechanismen ausgelöst.rn

Fluorescent-magnetic hybrid nanoparticles induce a dose-dependent increase in proinflammatory response in lung cells in vitro correlated with intracellular localization

Iron-platinum nanoparticles embedded in a poly(methacrylic acid) (PMA) polymer shell and fluorescently labeled with the dye ATTO 590 (FePt-PMA-ATTO-2%) are investigated in terms of their intracellular localization in lung cells and potential to induce a proinflammatory response dependent on concentration and incubation time. A gold core coated with the same polymer shell (Au-PMA-ATTO-2%) is also included. Using laser scanning and electron microscopy techniques, it is shown that the FePt-PMA-ATTO-2% particles penetrate all three types of cell investigated but to a higher extent in macrophages and dendritic cells than epithelial cells. In both cell types of the defense system but not in epithelial cells, a particle-dose-dependent increase of the cytokine tumor necrosis factor alpha (TNFalpha) is found. By comparing the different nanoparticles and the mere polymer shell, it is shown that the cores combined with the shells are responsible for the induction of proinflammatory effects and not the shells alone. It is concluded that the uptake behavior and the proinflammatory response upon particle exposure are dependent on the time, cell type, and cell culture.

Risk factors and mechanisms of hepatocarcinogenesis with special emphasis on alcohol and oxidative stress

Hepatocellular cancer is the fifth most frequent cancer in men and the eighth in women worldwide. Established risk factors are chronic hepatitis B and C infection, chronic heavy alcohol consumption, obesity and type 2 diabetes, tobacco use, use of oral contraceptives, and aflatoxin-contaminated food. Almost 90% of all hepatocellular carcinomas develop in cirrhotic livers. In Western countries, attributable risks are highest for cirrhosis due to chronic alcohol abuse and viral hepatitis B and C infection. Among those with alcoholic cirrhosis, the annual incidence of hepatocellular cancer is 1-2%. An important mechanism implicated in alcohol-related hepatocarcinogenesis is oxidative stress from alcohol metabolism, inflammation, and increased iron storage. Ethanol-induced cytochrome P-450 2E1 produces various reactive oxygen species, leading to the formation of lipid peroxides such as 4-hydroxy-nonenal. Furthermore, alcohol impairs the antioxidant defense system, resulting in mitochondrial damage and apoptosis. Chronic alcohol exposure elicits hepatocyte hyperregeneration due to the activation of survival factors and interference with retinoid metabolism. Direct DNA damage results from acetaldehyde, which can bind to DNA, inhibit DNA repair systems, and lead to the formation of carcinogenic exocyclic DNA etheno adducts. Finally, chronic alcohol abuse interferes with methyl group transfer and may thereby alter gene expression.

Dithiothreitol triggers photooxidative stress and fragmentation of the large subunit of ribulose-1,5-bisphosphate carboxylase/oxygenase in intact pea chloroplasts

In intact chloroplasts isolated from mature pea leaves (Pisum sativum L.), the large subunit (LSU) of ribulose-1,5-bisphosphate carboxylase/oxygenase (Rubisco, EC 4.1.1.39) was rapidly fragmented into several products upon illumination in the presence of 1 mM dithiothreitol (DTT). Very similar effects on LSU stability could be observed when illuminated chloroplasts were poisoned with cyanide which, like DTT, inhibits important plastid antioxidant enzymes, or when a light-dependent hydroxyl radical-producing system was added to the incubation medium. Moreover, DTT-stimulated light degradation of LSU was markedly delayed in the presence of scavengers of active oxygen species (AOS). It is therefore suggested that light degradation of LSU in the presence of DTT is mainly due to inhibition of the chloroplast antioxidant defense system and the subsequent accumulation of AOS in intact organelles. When chloroplasts were isolated from nonsenescent or senescent leaves, LSU remained very stable upon incubation without DTT, indicating that the antioxidant system was still functional in the isolated chloroplasts during leaf ageing. Our data support the notion that AOS might be important for the degradation of Rubisco in vivo under oxidative stress.

The opioid antagonist naltrexone and its pharmacological role in treating alcohol dependence: A literature review

Naltrexone, an opioid antagonist, was the second drug approved for treatment of alcohol dependence in the U.S. Its approval followed two landmark studies published in the U.S. in 1992. [1, 2] These studies showed that a combined treatment of naltrexone and behavioral therapy reduced alcohol consumption in alcoholics. Opioid antagonists decrease craving for alcohol and help to reduce drinking by blocking opioid peptide receptors in the body that are active in a dopamine chemical reward system. ^ Despite their usefulness, opioid antagonists have been underutilized. Health providers not educated in the use of opioid antagonists hold the view that opioid antagonist therapy is ineffective. However, it is apparent from the relevant literature that this therapy, when properly understood and targeted, has the potential to make a positive contribution in treating alcohol dependent patients. ^ This thesis will review the scientific literature and the present body of knowledge regarding opioid antagonists (naltrexone) and their pharmacological role in treating alcohol dependence.^

Experiment on wound activated production of Prostaglandin E2 and related toxic compounds in populations of Gracilaria vermiculophylla

The capacity of the East Asian seaweed Gracilaria vermiculophylla ("Ogonori") for production of prostaglandin E2 from arachidonic acid occasionally causes food poisoning after ingestion. During the last two decades the alga has been introduced to Europe and North America. Non-native populations have been shown to be generally less palatable to marine herbivores than native populations. We hypothesized that the difference in palatability among populations could be due to differences in the algal content of prostaglandins. We therefore compared the capacity for wound-activated production of prostaglandins and other eicosatetraenoid oxylipins among five native populations in East Asia and seven non-native populations in Europe and NW Mexico, using a targeted metabolomics approach. In two independent experiments non-native populations exhibited a significant tendency to produce more eicosatetraenoids than native populations after acclimation to identical conditions and subsequent artificial wounding. Fourteen out of 15 eicosatetraenoids that were detected in experiment I and all 19 eicosatetraenoids that were detected in experiment II reached higher mean concentrations in non-native than in native specimens. The datasets generated in both experiments are contained in http://doi.pangaea.de/10.1594/PANGAEA.855008. Wounding of non-native specimens resulted on average in 390 % more 15-keto-PGE2, in 90 % more PGE2, in 37 % more PGA2 and in 96 % more 7,8-di-hydroxy eicosatetraenoic acid than wounding of native specimens. The dataset underlying this statement is contained in http://doi.pangaea.de/10.1594/PANGAEA.854847. Not only PGE2, but also PGA2 and dihydroxylated eicosatetraenoic acid are known to deter various biological enemies of G. vermiculophylla that cause tissue or cell wounding, and in the present study the latter two compounds also repelled the mesograzer Littorina brevicula. The dataset underlying this statement is contained in http://doi.pangaea.de/10.1594/PANGAEA.854922. Non-native populations of G. vermiculophylla are thus more defended against herbivory than native populations. This increased capacity for activated chemical defense may have contributed to their invasion success and at the same time it poses an elevated risk for human food safety.

Performance data of the coral Pocillopora verrucosa and environmental conditions along the Saudi Arabian Red Sea coast as assessed during 3 expeditions in the years 2011 and 2012

Large scale patterns of ecologically relevant traits may help identify drivers of their variability and conditions beneficial or adverse to the expression of these traits. Antimicrofouling defenses in scleractinian corals regulate the establishment of the associated biofilm as well as the risks of infection. The Saudi Arabian Red Sea coast features a pronounced thermal and nutritional gradient including regions and seasons with potentially stressful conditions to corals. Assessing the patterns of antimicrofouling defenses across the Red Sea may hint at the susceptibility of corals to global change. We investigated microfouling pressure as well as the relative strength of 2 alternative antimicrofouling defenses (chemical antisettlement activity, mucus release) along the pronounced environmental gradient along the Saudi Arabian Red Sea coast in 2 successive years. Microfouling pressure was exceptionally low along most of the coast but sharply increased at the southernmost sites. Mucus release correlated with temperature. Chemical defense tended to anti-correlate with mucus release. As a result, the combined action of mucus release and chemical antimicrofouling defense seemed to warrant sufficient defense against microbes along the entire coast. In the future, however, we expect enhanced energetic strain on corals when warming and/or eutrophication lead to higher bacterial fouling pressure and a shift towards putatively more costly defense by mucus release.

Recuperación de energía de la salmuera

Como consecuencia del proceso de desalación, se produce el vertido al mar de un agua de rechazo hipersalino o salmuera. La salinidad de este vertido es variable, dependiendo del origen de la captación y del proceso de tratamiento. Muchos de los hábitats y biocenosis de los ecosistemas marinos se encuentran adaptados a ambientes de salinidad casi constante y son muy susceptibles a los incrementos de salinidad originados por estos vertidos. Junto con el vertido de salmuera otro de los principales inconvenientes que plantean las plantas desaladoras es el alto consumo energético, con todas las desventajas que esto supone: alto coste del agua desalada para los consumidores, contaminación del medio... El desarrollo de los métodos de vertido, herramientas de gestión de la salmuera, estudios del comportamiento de la pluma salina… ha buscado la mitigación de estos efectos sobre los ecosistemas marinos. El desarrollo en membranas de ósmosis inversa, diseño de bombas y sistemas de recuperación de energía ha permitido también la reducción del consumo energético en las plantas de desalación. Sin embargo, estos campos parecen haber encontrado un techo tecnológico difícil de rebasar en los últimos tiempos. La energía osmótica se plantea como uno de los caminos a investigar aplicado al campo de la reducción del consumo energético en desalación de agua de mar, a través del aprovechamiento energético de la salmuera. Con esta tesis se pretende cumplir principalmente con los siguientes objetivos: reducción del consumo energético en desalación, mitigar el impacto del vertido sobre el medio y ser una nueva herramienta en la gestión de la salmuera. En el presente documento se plantea el desarrollo de un nuevo proceso que utiliza el fenómeno de la ósmosis directa a través de membranas semipermeables, y busca la sinergia desalación depuración, integrando ambos, en un único proceso de tratamiento dentro del ciclo integral del agua. Para verificar los valores de producción, calidad y rendimiento del proceso, se proyecta y construye una planta piloto ubicada en la Planta Desaladora de Alicante II, escalada de tal manera que permite la realización de los ensayos con equipos comerciales de tamaño mínimo. El objetivo es que el resultado final sea extrapolable a tamaños superiores sin que el escalado afecte a la certeza y fiabilidad de las conclusiones obtenidas. La planta se proyecta de forma que el vertido de una desaladora de ósmosis inversa junto con el vertido de un terciario convencional, se pasan por una ósmosis directa y a continuación por una ósmosis inversa otra vez, ésta última con el objeto de abrir la posibilidad de incrementar la producción de agua potable. Ambas ósmosis están provistas de un sistema de pretratamiento físico-químico (para adecuar la calidad del agua de entrada a las condiciones requeridas por las membranas en ambos casos), y un sistema de limpieza química. En todos los ensayos se usa como fuente de disolución concentrada (agua salada), el rechazo de un bastidor de ósmosis inversa de una desaladora convencional de agua de mar. La fuente de agua dulce marca la distinción entre dos tipos de ensayos: ensayos con el efluente del tratamiento terciario de una depuradora convencional, con lo que se estudia el comportamiento de la membrana ante el ensuciamiento; y ensayos con agua permeada, que permiten estudiar el comportamiento ideal de la membrana. Los resultados de los ensayos con agua salobre ponen de manifiesto problemas de ensuciamiento de la membrana, el caudal de paso a través de la misma disminuye con el tiempo y este efecto se ve incrementado con el aumento de la temperatura del agua. Este fenómeno deriva en una modificación del pretratamiento de la ósmosis directa añadiendo un sistema de ultrafiltración que ha permitido que la membrana presente un comportamiento estable en el tiempo. Los ensayos con agua permeada han hecho posible estudiar el comportamiento “ideal” de la membrana y se han obtenido las condiciones óptimas de operación y a las que se debe tender, consiguiendo tasas de recuperación de energía de 1,6; lo que supone pasar de un consumo de 2,44 kWh/m3 de un tren convencional de ósmosis a 2,28 kWh/m3 al añadir un sistema de ósmosis directa. El objetivo de futuras investigaciones es llegar a tasas de recuperación de 1,9, lo que supondría alcanzar consumos inferiores a 2 kWh/m3. Con esta tesis se concluye que el proceso propuesto permite dar un paso más en la reducción del consumo energético en desalación, además de mitigar los efectos del vertido de salmuera en el medio marino puesto que se reduce tanto el caudal como la salinidad del vertido, siendo además aplicable a plantas ya existentes y planteando importantes ventajas económicas a plantas nuevas, concebidas con este diseño. As a consequence of the desalination process, a discharge of a hypersaline water or brine in the sea is produced. The salinity of these discharges varies, depending on the type of intake and the treatment process. Many of the habitats and biocenosis of marine ecosystems are adapted to an almost constant salinity environment and they are very susceptible to salinity increases caused by these discharges. Besides the brine discharge, another problem posed by desalination plants, is the high energy consumption, with all the disadvantages that this involves: high cost of desalinated water for consumers, environmental pollution ... The development of methods of disposal, brine management tools, studies of saline plume ... has sought the mitigation of these effects on marine ecosystems. The development of reverse osmosis membranes, pump design and energy recovery systems have also enabled the reduction of energy consumption in desalination plants. However, these fields seem to have reached a technological ceiling which is difficult to exceed in recent times. Osmotic power is proposed as a new way to achieve the reduction of energy consumption in seawater desalination, through the energy recovery from the brine. This thesis mainly tries to achieve the following objectives: reduction of energy consumption in desalination, mitigation of the brine discharge impact on the environment and become a new tool in the management of the brine. This paper proposes the development of a new process, that uses the phenomenon of forward osmosis through semipermeable membranes and seeks the synergy desalination-wastewater reuse, combining both into a single treatment process within the integral water cycle. To verify the production, quality and performance of the process we have created a pilot plant. This pilot plant, located in Alicante II desalination plant, has been designed and built in a scale that allows to carry out the tests with minimum size commercial equipment. The aim is that the results can be extrapolated to larger sizes, preventing that the scale affects the accuracy and reliability of the results. In the projected plant, the discharge of a reverse osmosis desalination plant and the effluent of a convencional tertiary treatment of a wastewater plant, go through a forward osmosis module, and then through a reverse osmosis, in order to open the possibility of increasing potable water production. Both osmosis systems are provided with a physicochemical pretreatment (in order to obtain the required conditions for the membranes in both cases), and a chemical cleaning system. In all tests, it is used as a source of concentrated solution (salt water), the rejection of a rack of a conventional reverse osmosis seawater desalination. The source of fresh water makes the difference between two types of tests: test with the effluent from a tertiary treatment of a conventional wastewater treatment plant (these tests study the behavior of the membrane facing the fouling) and tests with permeate, which allow us to study the ideal behavior of the membrane. The results of the tests with brackish water show fouling problems, the flow rate through the membrane decreases with the time and this effect is increased with water temperature. This phenomenon causes the need for a modification of the pretreatment of the direct osmosis module. An ultrafiltration system is added to enable the membrane to present a stable behavior . The tests with permeate have made possible the study of the ideal behavior of the membrane and we have obtained the optimum operating conditions. We have achieved energy recovery rates of 1.6, which allows to move from a consumption of 2.44 kWh/m3 in a conventional train of reverse osmosis to 2.28 kWh / m3 if it is added the direct osmosis system. The goal of future researches is to achieve recovery rates of 1.9, which would allow to reach a consumption lower than 2 kWh/m3. This thesis concludes that the proposed process allows us to take a further step in the reduction of the energy consumption in desalination. We must also add the mitigation of the brine discharge effects on the marine environment, due to the reduction of the flow and salinity of the discharge. This is also applicable to existing plants, and it suggests important economic benefits to new plants that will be built with this design.

Estudio de estabilidad de barreras de contención hidráulicas mediante tomografia eléctrica y placa de carga en Zaragoza

El objetivo del presente proyecto es definir las actuaciones encaminadas a restaurar el sistema actual de defensa del río Ebro en el tramo Pradilla de Ebro- Boquiñeni (Zaragoza), con el propósito de reducir el riesgo por inundaciones en los núcleos de población del mismo nombre, para lo que se ha realizado una campaña de reconocimiento del Terreno mediante técnicas geofísicas. La campaña de prospección ha consistido en la realización de perfiles de tomografía eléctrica para determinar la distribución de los niveles geoeléctricos en la zona obteniéndose la profundidad y variabilidad del nivel freático y la distribución aparente de los niveles biológicos. En base a las anomalías detectadas en las secciones de resistividad se han llevado a cabo ensayos in situ con placa de carga dinámica con el fin de determinar las características portantes de las barreras. La correlación de ambos estudios permite localizar las zonas de debilidad estructural para así poder establecer las recomendaciones oportunas de cara a restaurar los diques de protección, de forma que puedan cumplir con su función de contención frente a los caudales de crecida. ABSTRACT The aim of this project is so define the interventions required to restore the current defense system of Ebro River in the stretch between Pradilla de Ebro and Boquiñeni (Zaragoza), in order to reduce flood risk in the population centers of the same name, for what a soil survey has been done using geophysical techniques. The geophysical prospecting campaign has consisted on the realization of electrical tomography profiles to determine the distribution of due geoelectric levels in the area, the depth and variability of the water table and the distribution of apparent lithology level. Based on anomalies detected in resistivity sections, dynamic loading plate test were carried out in situ in order to determine the load bearing characteristics of the safety barriers. The correlation o f both studies makes possible to locate die areas o f structural weakness, with the objective of establishing appropriate recommendations to restore the embankments so that they can meet their retaining functions against flood flows.

Evaluating sustainability and food security of peasant farming systems in Mesoamerican highlands

En las últimas décadas, la agricultura sostenible ha sido objeto de gran interés y debate académico, no sólo en términos conceptuales, sino también en términos metodológicos. La persistencia de la inseguridad alimentaria y el deterioro de los recursos naturales en muchas regiones del mundo, ha provocado el surgimiento de numerosas iniciativas centradas en revitalizar la agricultura campesina así como renovadas discusiones sobre el rol que juega la agricultura como motor de desarrollo y principal actividad para alivio de la pobreza. Por ello, cuando hablamos de evaluar sistemas campesinos de montaña, debemos considerar tanto la dimensión alimentaria como las especificidades propias de los sistemas montañosos como base fundamental de la sostenibilidad. Al evaluar la contribución que han hecho alternativas tecnológicas y de manejo en la mejora de la sostenibilidad y la seguridad alimentaria de los sistemas campesinos de montaña en Mesoamérica, surgen tres preguntas de investigación: • ¿Se está evaluando la sostenibilidad de los sistemas campesinos teniendo en cuenta la variabilidad climática, la participación de los agricultores y las dinámicas temporales? • ¿Podemos rescatar tendencias comunes en estos sistemas y extrapolar los resultados a otras zonas? • ¿Son inequívocamente positivas las alternativas propuestas que se han llevado a cabo? En este trabajo se presentan tres evaluaciones de sostenibilidad que tratan de poner de manifiesto cuáles son los retos y oportunidades que enfrentan actualmente los sistemas campesinos de montaña. En primer lugar, se evalúan tres sistemas de manejo agrícola bajo dos años meteorológicamente contrastantes. Se determinó que durante el año que experimentó lluvias abundantes y temperaturas moderadas, los sistemas de bajos insumos, basados en el uso de abonos orgánicos y rotación de cultivos, obtuvieron los mejores resultados en indicadores ecológicos y similares resultados en los económicos y sociales que el sistema de altos insumos químicos. En el segundo año, con heladas tempranas y sequía invernal, la productividad se redujo para todos los sistemas pero los sistemas más diversificados (en variedades de maíz y/o siembra de otros cultivos) pudieron resistir mejor los contratiempos climáticos. En segundo lugar, se evalúa el grado de conocimiento (percepción) campesino para determinar los factores claves que determinan la sostenibilidad de sus sistemas y su seguridad alimentaria. Se determinó que los principales puntos críticos identificados por los campesinos (tamaño de parcela y pendiente del terreno) afectan de forma significativa a cuestiones de índole económica, pero no son capaces de explicar los desequilibrios alimenticios existentes. Realizando un análisis comparativo entre comunidades que presentaban buenos y malos resultados en cuanto a aporte energético y proteico, se determinó que la seguridad alimentaria estaba relacionada con la sostenibilidad de los sistemas y que concretamente estaba ligada a los atributos de equidad y autonomía. Otro resultado destacable fue que las comunidades más marginales y con mayor dificultad de acceso mostraron mayores niveles de inseguridad alimentaria, pero la variabilidad intergrupal fue muy alta. Eso demuestra que la seguridad alimentaria y nutricional forma parte de un complejo sistema de estrategias de autoabastecimiento ligada a la idiosincrasia misma de cada uno de los hogares. En tercer lugar, se evaluó el desempeño de las escuelas de campo de agricultores (ECAs) en la mejora de la sostenibilidad y la seguridad alimentaria de un sistema campesino de montaña. Para ver el efecto del impacto de estas metodologías a largo plazo, se estudiaron tres comunidades donde se habían implementado ECAs hace 8, 5 y 3 años. Encontramos que el impacto fue progresivo ya que fue la comunidad más antigua la que mejores valores obtuvo. El impacto de las ECAs fue rápido y persistente en los indicadores relacionados con la participación, el acceso a servicios básicos y la conservación de los recursos naturales. El estudio demostró un claro potencial de las ECAs en la mejora general de la sostenibilidad y la seguridad alimentaria de estos sistemas, sin embargo se observó una relación directa entre el aumento de producción agrícola y el uso de insumos externos, lo que puede suponer un punto crítico para los ideales sostenibles. ABSTRACT During the last decades, sustainable agriculture has been the subject of considerable academic interest and debate, not only in conceptual terms, but also in methodological ones. The persistence of high levels of environmental degradation and food insecurity in many regions has led to new initiatives focused on revitalizing peasant agriculture and renewed discussions of the role of sustainable agriculture as an engine for development, environmental conservation and poverty alleviation. Therefore, to assess mountain farming systems, we must consider food dimension and taking into account the specificities of the mountain systems as the foundation of sustainability. When evaluating contribution of technological and management alternative proposals in achieving sustainability and food security for peasant farming systems in Mesoamerican highlands, three research questions arise: • Is sustainability of peasant-farming systems being evaluated taking into account climate variability, participation of farmers and temporal dynamics? • Can we rescue common trends in these systems and extrapolate the results to other areas? • What alternative proposals that have been conducted are unequivocally positives? In this document, we present three evaluations of sustainability that try to highlight the challenges and opportunities that currently face mountain farming systems in Mesoamerica. First, we evaluate the sustainability of three agricultural management systems in two contrasting weather years. We determined that during the first year that exposed heavy rains and moderate temperatures, low-input systems, which are based on the use of organic fertilizers and crop rotation, provided better results in terms of ecological indicators and equal results in terms of economic and social indicators than those achieved using a high chemical input system. In the second year, which featured early frosts and a winter drought, productivity declined in all systems; however, the most diversified systems (in terms of the maize varieties grown and the sowing of other crops) more successfully resisted these climatic adversities. Second, we evaluate the farmers’ perception to determine the key drivers for achieving their sustainability and food and nutritional security. We determined that the key factors identified by farmers (landholding size and slope of cropland) exerted significant impacts on economic disparities but did not explain the malnutrition levels. We compared two contrasting hamlets according to their energy and protein supply, one namely Limón Timoté (LT), which did not present food problems and Limón Peña Blanca (LP), which did exhibit food insecurity. The results showed that FNS is linked to sustainability, and it is primarily related to the sustainability attributes of self-reliance and equity. Although the more marginated and inaccessible community exhibited more food insecurity, food and nutritional security depend upon a complex array of self-sufficiency strategies that remain linked to individual household idiosyncrasies. Third, we evaluated the impact of farmer field schools for improving the sustainability and food security of peasant mountain systems. In order to appreciate the long-term impact, we studied three communities where FFSs were implemented eight, five and three years ago, respectively. We found that FFSs have a gradual impact, as the community that first implemented FFSs scores highest. The impact of FFSs was broad and long-lasting for indicators related to participation, access to basic services and conservation of natural resources. This study demonstrates the potential of FFSs, but more attention will have to be paid to critical indicators in order to scale up their potential in the future. We observed a direct relationship between the increase in agricultural production and the use of external inputs, which is a critical point for sustainable ideals.

Analysis and optimization of trajectories for Ballistic Missiles Interception

Intercontinental Ballistic Missiles are capable of placing a nuclear warhead at more than 5,000 km away from its launching base. With the lethal power of a nuclear warhead a whole city could be wiped out by a single weapon causing millions of deaths. This means that the threat posed to any country from a single ICBM captured by a terrorist group or launched by a 'rogue' state is huge. This threat is increasing as more countries are achieving nuclear and advanced launcher capabilities. In order to suppress or at least reduce this threat the United States created the National Missile Defense System which involved, among other systems, the development of long-range interceptors whose aim is to destroy incoming ballistic missiles in their midcourse phase. The Ballistic Missile Defense is a high-profile topic that has been the focus of political controversy lately when the U.S. decided to expand the Ballistic Missile system to Europe, with the opposition of Russia. However the technical characteristics of this system are mostly unknown by the general public. The Interception of an ICBM using a long range Interceptor Missile as intended within the Ground-Based Missile Defense System by the American National Missile Defense (NMD) implies a series of problems of incredible complexity: - The incoming missile has to be detected almost immediately after launch. - The incoming missile has to be tracked along its trajectory with a great accuracy. - The Interceptor Missile has to implement a fast and accurate guidance algorithm in order to reach the incoming missile as soon as possible. - The Kinetic Kill Vehicle deployed by the interceptor boost vehicle has to be able to detect the reentry vehicle once it has been deployed by ICBM, when it offers a very low infrared signature, in order to perform a final rendezvous manoeuvre. - The Kinetic Kill Vehicle has to be able to discriminate the reentry vehicle from the surrounding debris and decoys. - The Kinetic Kill Vehicle has to be able to implement an accurate guidance algorithm in order to perform a kinetic interception (direct collision) of the reentry vehicle, at relative speeds of more than 10 km/s. All these problems are being dealt simultaneously by the Ground-Based Missile Defense System that is developing very complex and expensive sensors, communications and control centers and long-range interceptors (Ground-Based Interceptor Missile) including a Kinetic Kill Vehicle. Among all the technical challenges involved in this interception scenario, this thesis focuses on the algorithms required for the guidance of the Interceptor Missile and the Kinetic Kill Vehicle in order to perform the direct collision with the ICBM. The involved guidance algorithms are deeply analysed in this thesis in part III where conventional guidance strategies are reviewed and optimal guidance algorithms are developed for this interception problem. The generation of a realistic simulation of the interception scenario between an ICBM and a Ground Based Interceptor designed to destroy it was considered as necessary in order to be able to compare different guidance strategies with meaningful results. As a consequence, a highly representative simulator for an ICBM and a Kill Vehicle has been implemented, as detailed in part II, and the generation of these simulators has also become one of the purposes of this thesis. In summary, the main purposes of this thesis are: - To develop a highly representative simulator of an interception scenario between an ICBM and a Kill Vehicle launched from a Ground Based Interceptor. -To analyse the main existing guidance algorithms both for the ascent phase and the terminal phase of the missiles. Novel conclusions of these analyses are obtained. - To develop original optimal guidance algorithms for the interception problem. - To compare the results obtained using the different guidance strategies, assess the behaviour of the optimal guidance algorithms, and analyse the feasibility of the Ballistic Missile Defense system in terms of guidance (part IV). As a secondary objective, a general overview of the state of the art in terms of ballistic missiles and anti-ballistic missile defence is provided (part I).

Factores anatómicos, dendrométricos y climáticos implicados en la producción de resina de Pinus pinaster AIT. : aplicación a la mejora de los métodos de resinación

Pinus pinaster Ait. es la conífera con mayor área de distribución en la Península Ibérica y es, a día de hoy, la única especie resinada en nuestro país. La inducción del flujo de resina al exterior para su recolección a través de distintos tipos de heridas ha sido practicada desde hace miles de años por distintas culturas. En todos los casos, las técnicas desarrolladas se basan en la estimulación del característico sistema de defensa de las pináceas. En los últimos siete años se viene observando una tendencia de incremento sustancial de la superficie resinada en España, acompañada por avances tecnológicos dirigidos a la mecanización y mejora de estimulantes. El aprovechamiento resinero se perfila como un sector estratégico en la generación de empleo rural y la conservación de ecosistemas. La industria resinera demanda métodos de extracción más eficaces, una selvicultura adecuada y actualizada, y condiciones laborales de los resineros más dignas con objeto de llegar a ser competitiva en el mercado internacional. Este trabajo se centra en ampliar el conocimiento sobre el sistema de defensa de P. pinaster, concretamente sobre las estructuras y procesos que pueden afectar a la producción de resina. Se analizan las relaciones entre las características anatómicas del xilema, destacando las relacionadas con los canales resiníferos, las variables dendrométricas y dasométricas de la masa y el flujo de resina (objetivo 1). Se estudia cómo estas relaciones son moduladas por las heridas de resinación dependiendo de la técnica de resinación aplicada (objetivo 2), el clima y el balance hídrico del suelo (objetivo 3). El material vegetal, las muestras de suelo y los datos de producción de resina y climáticos usados en esta tesis han sido recogidos en tres montes de utilidad pública; MUP 101 en Armuña, MUP 108 en Melque de Cercos y MUP 117 en Nieva (en esta última solo se recogieron los datos de producciones), todos ellos pinares monoespecíficos de P. pinaster localizados en la denominada Tierra de Pinares Segoviana. En los árboles de nuestro estudio se han aplicado cuatro métodos de resinación: método de pica de corteza con estimulante y método mecanizado con estimulante, ambos en sentido ascendente y descendente. En los trabajos realizados para el análisis de la influencia de la anatomía constitutiva en la producción de resina (objetivo 1) y el efecto del clima (objetivo 3), se obtuvieron muestras del xilema de 26 árboles resinados en Melque de Cercos y Armuña y 12 árboles control sin resinar. Para caracterizar los pies estudiados, se midió la altura, diámetro normal y porcentaje de copa viva. Las muestras de tejido fueron recogidas en una zona del tronco a una distancia del límite de la herida considerada en la bibliografía como no afectada (anatomía constitutiva). Para el análisis de las alteraciones anatómicas inducidas por la herida (objetivo 2), se recogieron muestras en ocho de los individuos en los que se habían realizado los distintos métodos de resinación descritos y en cinco árboles control. Se obtuvieron ocho muestras de tejido distribuidas en la parte superior, inferior, lateral y centro de la herida de cada uno de los árboles resinados. Para establecer las diferencias en la producción de resina según el método de resinación, se analizaron las producciones de 561 árboles resinados en 2012 con estos cuatro métodos en Nieva. Los principales resultados de estos trabajos muestran que la producción de resina está ligada al volumen de canales (axiales y radiales) y a la frecuencia de canales radiales existentes en el árbol antes de efectuar ninguna herida (sistema constitutivo). De esta manera, los árboles grandes productores de resina mostraron una red de canales más densa que aquellos con producciones medias. Una vez realizada la herida de resinación, observamos una disminución del ancho del anillo de crecimiento y del tamaño medio de los canales axiales a la vez que se incrementaba la frecuencia y área ocupada por mm2 de anillo de estos canales. Estos cambios perduraron en el árbol durante al menos tres años y fueron distintos dependiendo de la localización en el entorno de la herida y del método de resinación. Las respuestas más intensas a la herida se observaron el año siguiente a la realización de la misma, en dirección axial, para las distancias más próximas al límite de la herida y para los métodos de resinación en sentido ascendente. Además, se ha constatado que como consecuencia de las heridas de resinación se produjeron cambios en la anatomía del xilema en zonas alejadas de la herida, tanto en el año de la herida como años posteriores. Es decir, se observó una respuesta sistémica del árbol. Respecto al papel del clima como regulador de la respuesta del árbol, se ha evidenciado que la temperatura, la radiación y la ETP influyeron en la producción de resina, no solo durante la campaña de resinación, sino también durante los meses anteriores. El déficit hídrico favoreció la producción y la formación de canales axiales pero, a partir de un determinado umbral, esa relación se invirtió y las lluvias estivales incrementaron la producción. Algunas de estas variables climáticas se asociaron a cambios en el tamaño y frecuencia de las estructuras secretoras, las cuales posiblemente modulan la respuesta defensiva de la planta. La dendrometría del árbol (evaluada a través del diámetro normal, altura y porcentaje de copa viva), la densidad de la masa y el tipo de suelo influyeron en el potencial de producción de resina de P. pinaster. Árboles más vigorosos, parcelas con menores densidades y suelos con más capacidad para la retención de agua y nutrientes presentaron producciones mayores. Estos trabajos se complementan en anexos con una caracterización del sistema socio-ecológico del pinar en resinación. En ese trabajo se identifican sus potenciales servicios ecosistémicos y se evalúa su grado de vinculación con el aprovechamiento resinero con objeto de valorar su funcionalidad y aproximar una valoración económica de modo que sea posible apreciar la importancia económica de los mismos. Para concluir, podemos resaltar que son necesarios más trabajos de carácter científico para avanzar en la comprensión de los procesos anatómicos y fisiológicos que regulan la secreción de resina en P. pinaster y sus interacciones con el medio. Esto permitiría avances certeros hacia el desarrollo de métodos de extracción más eficaces, una selvicultura óptima, el reconocimiento de los beneficios socio-ecológicos y económicos del aprovechamiento y, de manera general, una bibliografía amplia y fiable para la consulta y desarrollo de futuras mejoras que posibiliten la reactivación y conservación de la resinación como aprovechamiento rentable. ABSTRACT Pinus pinaster Ait. is the most widespread conifer in Spain and is now the only species tapped for its oleoresin. External induction of resin secretion, based on the defense system of Pinus trees, has been performed by humans since Classical times through various methods. The socio-economic implication of this practice in Spain justifies a new approach to improve tapping methodology and understand the effects of this activity on the tree. In the last five years, sharp increases in the price of natural resins, accompanied by technological advances directed toward mechanization, have made resin tapping a strategic activity for rural development and forest conservation. The resin industry demands more efficient tapping methods and forest management plans as a way to increase competitiveness in a global market. In this way, this work focuses on the study of the defense system of P. pinaster, with the aim to understand the effects of anatomical and physiological characteristics and environmental conditions on resin yield. The relationships between anatomical variables -with special focus on resin canals-, dendrometric and dasometric variables, and resin yield will be evaluated (objective 1). The tapping wound effects (objective 2) and the intra- and inter-annual variability of climate conditions and soil water availability influence (objective 3) on resin yield will be also studied. The plant and soil material and the resin yield and climatic data used in this thesis have been collected in stands of three public forests of P. pinaster; Armuña, Melque de Cercos and Nieva, located in Segovia (Central Spain). Trees were tapped using two different methods: mechanized or traditional tool, in both upwards and downwards direction. Twenty-six tapped trees of contrasting resin yield classes and twelve non-tapped (control) trees, growing in two locations (Armuña y Melque de Cercos) with the same climate but different stand density and soil characteristics, were selected for studying the role of tree size, xylem anatomy at distal parts aside from the tapping wound (objective 1) and climate influence (objective 3) on resin yield. Concerning the tree defenses induced by the tapping wound (objective 2), the xylem of eight trees, tapped with the two described methods in both upwards and downwards direction, were analyzed. From each tapped tree, eight cores were collected at different locations and varying distances from the tapping wound. In each core, a histological analysis was made. Growth ring width, earlywood and latewood width, and axial canal frequency, area, mean size and location were measured. The effect of the tapping method on resin yield was assessed in 561 P. pinaster tapped trees in a stand in Nieva. In tissues not affected by the tapping wound, the frequency of radial resin canals and the total volume of resin canals were related to resin yield. The frequency of radial canals and the resin yield were strongly related to tree diameter and percentage of live crown. High area of axial resin canals per mm2 was related to high yielding trees, but only in the location with higher plant density and poorer soil quality. In tapped trees, an increase in axial canal frequency and area was found during the three years following the start of tapping activity, suggesting that canal formation is a systemic induced response to wounding. The highest mean annual resin yield was found using the traditional tool in upwards direction, which also induced the highest increase in axial canal frequency and area. The lowest yield was found for mechanized tapping, which showed no differences between the upwards and downwards directions. The strongest induction of systemic induced responses in terms of resin canal frequency and area was detected one year after tapping for upwards tapping. This suggests the involvement of signaling processes that spread mainly upwards, and the importance of adaptive processes as a defense against periodic insect attacks. Intra-annual variation in resin yield was strongly correlated with temperature, solar radiation, potential evapotranspiration and soil water deficit. Inter-annual variation in resin yield and resin canal abundance were correlated with temperature and water deficit in spring, but above a certain threshold of cumulated water deficit in summer rainfall favored resin yield. Under adverse climate scenarios where resource optimization is desirable, a reduced tapping season during the warmest months (June–September) would be advisable, assuming a very small production loss relative to traditional tapping season. Similarly, in years with a rainy summer and/or dry spring, a slightly longer tapping season could be suggested, as resin yield increases after these events. Tree diameter and percentage of live crown, and radial resin canal frequency could be useful criteria for estimating resin yields in P. pinaster. Vigorous trees in lower density stands and growing up in good quality soils will be the most productive. These conclusions could be applied to improve tapping management and breeding programs. These works are complemented with socio-ecological characterization, the identification of the main ecosystem services and an assessment of the possible economic impact derived from the tapping practice. To conclude, more scientific studies are necessary for understanding the anatomical and physiological processes behind resin synthesis and their interactions with the environment. This would afford further progresses towards an extensive and reliable bibliography and improved tapping methods and optimal selvicultural guide lines.