Assessment of seawater pollution by heavy metals (lead & cadmium) in the Qeshm rocky shore: use of the sea urchin, Echinometra mathaei, as a bioindicator

The general purpose of this study is to investigate the degree of heavy metal accumulation in hard and soft tissue of sea urchin, and determining these tissues as the most suitable bioindicator for lead and cadmium in the environment of the sampling stations. The way of doing this assessment was MOOPAM. Samples were prepared and classified according to sea urchin organ (soft tissue, hard tissue, Tube feet, Test, Lantern Structure and spines) and then lead and cadmium were measured in them. Result of this study shows that hard tissue is a better index of lead and cadmium than soft tissue. The result of bioaccumulation of lead in the related tissue was found to be in the following order: Soft tissue=21, hard tissue=28.1, Test=20.8, Lantern Structure=20.5 and spines=23.9. The result of bioaccumulation of cadmium in the related tissue was found to be in the following order: Soft tissue=9. 7, hard tissue=5.01, Test=4.2, Lantern Structure=4.06 and spines=5.53.

Screening of Polyalthia longifolia and Aloe vera for their phytoextractability of heavy metals in tropical soil of the Niger Delta

The work focuses on the screening of Polyalthia longifolia and Aloe vera for their phytoextractability of heavy metal in soil of the Niger Delta. 5kg of soil was polluted with 100 mg of Zn, Fe and Pb each replicated 9 times. Each set was separated into 3 subgroups. The subgroups were phytoextracted with Polyalthia longifolia and Aloe vera alongside a control (no phytoextraction) respectively. After 12 weeks, the concentration of Lead, Iron and Zinc in soils, roots and shoots was determined. Results showed that the two plants have phytoextraction ability with reductions in Zn, Fe, and Pb in the phytoextraction soil . Metal transfer factor was PB: Aloe vera (0.881) > P. longifolia (0.315); Zn: P. longifolia (0.614) > Aloe vera (0.606); Fe: Aloe vera (0.812) > P. longifolia (0.774). Translocation factors for the two plants were in the order: Zn: P. longifolia (0.79) > Aloe vera (0.36); Fe: P. longifolia (0.63) > Aloe vera (0.05); Pb: P. longifolia (0.57) > Aloe vera (0.23). Since the translocation factors were < 1, the plants can be classified as non- hyperaccumulators for these metals.

Levels of some heavy Metals in Cocoyam ( Colocasia esculentum ) grown on Soil receiving Effluent from a Paint Industry

The levels of some heavy metals in soil samples and tubers of cocoyam ( Colocasia esculentum ) grown on soil receiving paint wastes (PWS) has been investigated using Atomic Absorption spectrophotometer (Unicam 939/959 model). Similar analyses were carried out for the same plant from a control area. The studies revealed that although the P.W.S contained abnormally high levels of Pb (474.14mgkg-1) and Cu (137.85mgkg-1). The paint waste tuber (PWT) recorded low levels of these metals: Pb (2.13mgkg-1) and Cu (13.85mgkg-1) respectively. Correlation analysis tested at 0.05 level of significance show that no significant correlation existed between the metals levels in the soil and the level in the tuber. In all cases the levels of the metals in the tubers were well below the upper limit documented for unpolluted plant. The results however suggest the ineffectiveness of the use of Colocasia esculentum as a bioindicator for heavy metal pollution in soil.

X-ray fluorescence spectroscopic determination of heavy metals and trace elements in aerial parts of Origanum sipyleum L from Turkey

Purpose: To determine the heavy metal and trace element composition of the powdered aerial parts of Origanum sipyleum L. and its water extract. Methods: The heavy metal and trace elements content of the powdered plant material and 2 % aqueous extract were evaluated by x-ray fluorescence spectroscopy with silicon drift detector SDD at a resolution of 145 eV and 10,000 pulses. The process conditions were 0.1 g sample weight, process time of 300 s at a voltage of 25 kV and 50 kV, and at a current of 0.5 and 1.0 mA under helium atmosphere. Results: The major elements, K, Ca and Na, known as macronutrients, constituted 11990, 10490 and 970 ppm of the powdered drug and 8910, 2991 and 810 ppm of the water extract, respectively. Among other constituents, arsenic, lead and uranium levels were < 1, 2.1 and < 3 ppm, respectively, in the powdered material while in the aqueous extract, the levels were < 1, < 2 and 200 ppm, respectively. Conclusion: O. sipyleum is a potential source of macro- and micronutrients from which useful food additives and health supplements can be derived.

A comparative study of alginate beads and an ion-exchange resin for the removal of heavy metals from a metal plating effluent

The capacity of dry protonated calcium alginate beads to sorb metals from an industrial effluent was studied and compared with a commercial ion-exchange resin (Lewatit TP 207). Both sorbents decreased zinc, nickel, iron and calcium concentrations in the effluent, and released sodium during treatment. Alginate beads removed lower amounts of heavy metals than the resin, but exhibited faster uptake kinetics. Zinc desorption from the sorbents was achieved in 30 minutes using 0.1 M HCl or 0.1 M H(2)SO(4). Desorption ratios with these acids varied between 90 and 100% for alginate, and 98 to 100% for the ion-exchange resin. Reusability tests with HCl showed that alginate beads can stand acid desorption and recover binding capacity. Overall, the comparison of dry protonated alginate beads with the resin supports the potential of the biosorbent for the treatment of industrial effluents.

Initial growth of sunflower in soils with high concentrations of boron and heavy metals.

Phytoremediation studies have been conducted in an area contaminated by heavy metals, located in Piracicaba - SP, Brazil. This area was contaminated accidentally by the addition of auto scrap shredding to the soil and was limed later to reduce heavy metal mobility in the environment. Previous characterization showed that it also presents high concentration of boron, which has limited the initial plant development of some species. As sunflower plants require a high boron supply and the literature describes its use in the phytoremediation of soils contaminated with heavy metals under some conditions, the aim of this work was to evaluate its potential for the remediation of this area. In the present study, the results of preliminary tests are presented, aiming at the evaluation of sunflower plant germination and its initial development when cultivated in the contaminated soil described. Two sunflower hybrids were sown in soils treated with different rates of boron and in the soil from the contaminated area in study. The results showed that sunflower plants had a normal initial development, even in the soil from the contaminated area. Therefore, sunflower is a promising crop and further studies will be developed to evaluate the sunflower efficiency in phytoextraction or phytostabilization of heavy metals in areas where boron contamination also occurs, as is the case in the study area.

Initial growth of sunflower in soils with high concentrations of boron and heavy metals.

2008

Assessment of heavy metals in soils of a vineyard region with the use of principal component analysis.

Agricultural management with chemicals may contaminate the soil with heavy metals. The objective of this study was to apply Principal Component Analysis and geoprocessing techniques to identify the origin of the metals Cu, Fe, Mn, Zn, Ni, Pb, Cr and Cd as potential contaminants of agricultural soils. The study was developed in an area of vineyard cultivation in the State of São Paulo, Brazil. Soil samples were collected and GPS located under different uses and coverings. The metal concentrations in the soils were determined using the DTPA method. The Cu and Zn content was considered high in most of the samples, and was larger in the areas cultivated with vineyards that had been under the application of fungicides for several decades. The concentrations of Cu and Zn were correlated. The geoprocessing techniques and the Principal Component Analysis confirmed the enrichment of the soil with Cu and Zn because of the use and management of the vineyards with chemicals in the preceding decades.

Heavy Metals distribution in drainage canals sediments of the Ravenna province

This work, in collaboration with the Romagna Reclamation Consortium, has the aim of studying the heavy metals concentration distribution in the drainage canals of the Ravenna coastal basins, Italy. Particular attention was given to the area of the V Fosso Ghiaia and VI Bevanella basins, where water and sediment samples were collected in the field and integrated with existing databases. The hydrological regime is controlled and managed by the Consortium, which has divided the territory into several mechanical drainage basins. XRF was performed on 21 sediment samples and pH, EC, T°, Fe2+ and Fetot were measured on 15 water samples by probes and spectrophotometer, respectively. Heavy metals concentrations exceeding legal limits of the D.LGS n ° 152/2006 were found for As, Co, Cr, Pb and Zn. These results were then integrated with canal sediment analyses provided by the Consortium to perform a Principal Component Analysis. PCA results show that the main variable affecting heavy metals distribution is the use of fertilizers, followed by distance from sea, and altimetry, which are directly linked to salinity. Heavy metals concentrations increase with increasing use of fertilizers, which are mainly due to the widespread agricultural practices and industrial land use in the area. High heavy metals concentrations are also found in the canals interested by higher salinity (especially Pinetale Ramazzotti). In fact, the area is affected by salinization caused by a water table below sea level and upward seepage of salty oxygen-poor saline water from the bottom of the aquifer. According to the literature, iron and manganese oxides were found to be an important factor in controlling the heavy metals distribution.

Synthesis of nanoporous materials for preconcentration and determination of trace elements by ICP-AES ; Investigation and elimination of the memory effects of mercury, gold, silver and boron in ICP-AES

Nanoporous materials with large surface area and well-ordered pore structure have been synthesized. Thiol groups were grafted on the materials' surface to make heavy metal ion pre-concentration media. The adsorption properties ofthe materials were explored. Mercury, gold and silver can be strongly adsorbed by these materials, even in the presence of alkaline earth metal ion. Though the materials can adsorb other heavy metal ions such as lead and copper, they show differential adsorption ability when several ions are present in solution. The adsorption sequence is: mercury> == silver> copper » lead and cadmium. In the second part of this work, the memory effects of mercury, gold, silver and boron were investigated. The addition of 2% L-cysteine and 1% thiourea eliminates the problems of the three metal ions completely. The wash-out time for mercury dropped from more than 20 minutes to 18 seconds, and the wash-out time for gold decreased from more than 30 minutes to 49 seconds. The memory effect of boron can be reduced by the use of mannitol.

Removal of Zn(2+) from Electroplating Wastewater Using Modified Wood Sawdust and Sugarcane Bagasse

This paper describes the preparation of new adsorbents derived from sugarcane bagasse and wood sawdust (Manilkara sp.) to remove zinc (II) ions from electroplating wastewater. The first part deals with the chemical modification of sugarcane bagasse and wood sawdust, using succinic anhydride to introduce carboxylic acid functions into the material. The obtained materials (modified sugarcane bagasse MB2 and modified wood sawdust MS2) were then characterized by infrared spectroscopy (IR) and used in adsorption experiments. The adsorption experiments evaluates Zn(2+) removal from aqueous single metal solution and real electroplating wastewater on both batch and continuous experiments using fixed-bed columns prepared in laboratorial scale with the obtained adsorbents. Adsorption isotherms were then developed using Langmuir model and the Thomas kinetic model. The calculated Zn(2+) adsorption capacities were found to be 145 mg/g for MS2 and 125 mg/g for MB2 in single metal aqueous solution, whereas for the industrial wastewater these values were 61 mg/g for MS2 and 55 mg/g for MB2.

Preparação e caracterização de um material híbrido, à base de vermiculita modificada com quitosana, para a remoção de íons de chumbo presentes em efluentes sintéticos

Actually, surveys have been developed for obtaining new materials and methodologies that aim to minimize environmental problems due to discharges of industrial effluents contaminated with heavy metals. The adsorption has been used as an alternative technology effectively, economically viable and potentially important for the reduction of metals, especially when using natural adsorbents such as certain types of clay. Chitosan, a polymer of natural origin, present in the shells of crustaceans and insects, has also been used for this purpose. Among the clays, vermiculite is distinguished by its good ion exchange capacity and in its expanded form enhances its properties by greatly increasing its specific surface. This study aimed to evaluate the functionality of the hybrid material obtained through the modification of expanded vermiculite with chitosan in the removal of lead ions (II) in aqueous solution. The material was characterized by infrared spectroscopy (IR) in order to evaluate the efficiency of modification of matrix, the vermiculite, the organic material, chitosan. The thermal stability of the material and the ratio clay / polymer was evaluated by thermogravimetry. To evaluate the surface of the material was used in scanning electron microscopy (SEM) and (BET). The BET analysis revealed a significant increase in surface area of vermiculite that after interaction with chitosan, was obtained a value of 21, 6156 m2 / g. Adsorption tests were performed according to the particle size, concentration and time. The results show that the capacity of removal of ions through the vermiculite was on average 88.4% for lead in concentrations ranging from 20-200 mg / L and 64.2% in the concentration range of 1000 mg / L. Regarding the particle size, there was an increase in adsorption with decreasing particle size. In fuction to the time of contact, was observed adsorption equilibrium in 60 minutes with adsorption capacity. The data of the isotherms were fitted to equation Freundlich. The kinetic study of adsorption showed that the pseudo second- order model best describes the adsorption adsorption, having been found following values K2=0,024 g. mg-1 min-1and Qmax=25,75 mg/g, value very close to the calculated Qe = 26.31 mg / g. From the results we can conclude that the material can be used in wastewater treatment systems as a source of metal ions adsorbent due to its high adsorption capacity

Utilização de microemulsões como agentes modificadores de superfícies para remoção de íons metálicos

The heavy metals are used in many industrial processes and when discharged to the environment can cause harmful effects to human, plants and animals. The adsorption technology has been used as an effective methodology to remove metallic ions. The search for new adsorbents motivated the development of this research, accomplished with the purpose of removing Cr (III) from aqueous solutions. Diatomite, chitosan, Filtrol 24TM and active carbon were used as adsorbents. To modify the adsorbent surface was used a bicontinuous microemulsion composed by water (25%), kerosene (25%), saponified coconut oil (10%) and as co-surfactant isoamyl or butyl alcohols (40%). With the objective of developing the best operational conditions the research started with the surfactant synthesis and after that the pseudo-ternary diagrams were plotted. It was decided to use the system composed with isoamyl alcohol as co-surfactant due its smallest solubility in water. The methodology to impregnate the microemulsion on the adsorbents was developed and to prepare each sample was used 10 g of adsorbent and 20 mL of microemulsion. The effect of drying time and temperature was evaluated and the best results were obtained with T = 65 ºC and t = 48 h. After evaluating the efficiency of the tested adsorbents it was decided to use chitosan and diatomite. The influence of the agitation speed, granule size, heavy metal synthetic solution concentration, pH, contact time between adsorbent and metal solution, presence or not of NaCl and others metallic ions in the solution (copper and nickel) were evaluated. The adsorption isotherms were obtained and Freundlich and Langmuir models were tested. The last one correlated better the data. With the purpose to evaluate if using a surfactant solution would supply similar results, the adsorbent surface was modified with this solution. It was verified that the adsorbent impregnated with a microemulsion was more effective than the one with a surfactant solution, showing that the organic phase (kerosene) was important in the heavy metal removal process. It was studied the desorption process and verified that the concentrated minerals acids removed the chromium from the adsorbent surface better than others tested solutions. The treatment showed to be effective, being obtained an increase of approximately 10% in the chitosan s adsorption capacity (132 mg of Cr3+ / g adsorbent), that was already quite efficient, and for diatomite, that was not capable to remove the metal without the microemulsion treatment, it was obtained a capacity of 10 mg of Cr3+ / g adsorbent, checking the applied treatment effectiveness

Sorption and preconcentration of metal ions in ethanol solution with a silica gel surface chemically modified with benzimidazole

The adsorption isotherms of MCl(2) (M = Mn, Ni, Cu, Zn and Cd) and FeCl3 by silica gel chemically modified with benzimidazole molecules (= SI(CH2)(3)-NC7H5N) were studied in ethanol solution at 298 K. A column made of modified silica was used to adsorb and preconcentrate the above metal ions from ethanol solution. Elution was done with 0.1 M hydrochloric acid in an ethanol/water mixture having a mole fraction of water of 0.8. The material was applied in the preconcentration of metal ions from commercial ethanol normally used as engine fuel.