Numerical study of the impact of inoculant and grain transport on macrosegregation and microstructure formation during solidification of an Al-22%Cu alloy

We investigate the impact of the nucleation law for nucleation on Al-Ti-B inoculant particles, of the motion of inoculant particles and of the motion of grains on the predicted macrosegregation and microstructure in a grain-refined Al-22 wt.% Cu alloy casting. We conduct the study by numerical simulations of a casting experiment in a side-cooled 76×76×254 mm sand mould. Macrosegregation and microstructure formation are studied with a volume-averaged two-phase model accounting for macroscopic heat and solute transport, melt convection, and transport of inoculant particles and equiaxed grains. On the microscopic scale it accounts for nucleation on inoculant particles with a given size distribution (and corresponding activation undercooling distribution)and for the growth of globular solid grains. The growth kinetics is described by accounting for limited solute diffusion in both liquid and solid phases and for convective effects. We show that the consideration of a size distribution of the inoculants has a strong impact on the microstructure(final grain size) prediction. The transport of inoculants significantly increases the microstructure heterogeneities and the grain motion refines the microstructure and reduces the microstructure heterogeneities.

Temperature Dependence of the Tribological Properties of Laser Re-Melted Al-Cu-Fe Quasicrystalline Plasma Sprayed Coatings

The aim of this study was to investigate the effect of temperature on tribological properties of plasma-sprayed Al-Cu-Fe quasicrystal (QC) coating after laser re-melting treatment. The laser treatment resulted in a more uniform, denser and harder microstructure than that of the as-sprayed coatings. Tribological experiments on the coatings were conducted under reciprocating motion at high frequency in the temperature range from 25 to 650 degreesC. Remarkable influence of temperature on the friction behavior of the coating was recorded and analyzed. Microstructural analysis indicated that the wear mechanisms of the re-melted QC coatings changed from abrasive wear at room temperature, to adhesive wear at 400 degreesC and severe adhesive wear at 650 degreesC owing to the material transfer of the counterpart ball. It was also observed that the ratio of the icosahedral (i)-phase to beta-Al-50(Fe,CU)(50) phase in the coating was higher after test at 400 'C than that at 650 'C. The variation of the ratio UP of coating and of the property of the counterpart ball and coating with the temperature are the two main factors influencing the wear mechanisms and value of the friction coefficient.

Mg-Al-NO_3层状双金属氢氧化物电性质研究

采用电泳法和电势滴定法测定出不同电解质(LiCl,NaCl和KCl）溶液中Mg-Al-NO_3层状双金属氢氧化物（Mg-Al-NO_3LDH)颗粒的$\Xi$电位、等电点、永久电荷密度以及零电荷点等电化学物理量，探讨了电解质、pH和样品化学组成对Mg-Al-NO_3LDH电性质的影响。研究发现一价阳离子Li+，Na+,K+对Mg-Al-NO_3LDH颗粒的等电点有影响，使等电点依次降低；由于永久电荷的存在，等电点与零电荷点不一致。随着样品中Al含量的增加，永久电荷密度依次增加，零电荷点依次增大，而等电点依次降低。

Produção de biodiesel pela rota heterogênea empregando catalisadores a base de Zn e Al

Nos últimos anos, a busca por fontes de energia renováveis e o desenvolvimento de novas tecnologias para a produção de biocombustíveis têm sido objeto de intensa investigação. O biodiesel é um combustível biodegradável, derivado de fontes renováveis e é obtido em escala industrial principalmente através da reação de transesterificação de óleos vegetais e/ou gorduras animais com metanol na presença de catalisadores homogêneos, como NaOH. Entretanto, a utilização de catalisadores heterogêneos tem sido sugerida por diversos autores, por apresentar vantagens como a eliminação dos problemas de separação e purificação dos produtos obtidos. No presente trabalho foi investigada a produção de biodiesel a partir da transesterificação do óleo de soja com metanol utilizando óxidos mistos de Zn e Al como catalisadores sólidos básicos. A influência das variáveis: temperatura, concentração de catalisador e relação molar metanol/óleo de soja na produção de biodiesel foi avaliada. Os catalisadores preparados apresentaram predominantemente sítios básicos e foram ativos frente à reação estudada, sendo os resultados mais promissores apresentados pelo óxido misto com relação molar Al/(Al+Zn)=0,50, obtido por tratamento térmico à 450C, que apresentou rendimentos em ésteres metílicos de até 98,5% sob condições específicas. A metodologia da superfície de resposta foi utilizada visando estabelecer as condições ótimas para maximizar o rendimento em ésteres metílicos, tendo sido encontradas a temperatura de 165oC e a concentração de catalisador de 5,8% m/m em relação massa de óleo, no caso da relação molar metanol/óleo de soja limitada em 15. Essa limitação teve como objetivo garantir um processo viável em escala comercial

Cellular and molecular responses of zebrafish to legacy and emerging pollutants: the specific cases of PAHs and metal oxide nanoparticles

270 p.

Síntese, caracterização e aplicações na desidrogenação oxidativa de propano de materiais tipo hidrotalcita Ni-Mg-Al com diferentes ânions de compensação

Na reação de desidrogenação oxidativa de propano (ODHP), propano reage com oxigênio da superfície de metais de transição para produzir propeno e água, em temperaturas de 300-700C. Porém, o propeno pode facilmente oxidar, formando CO e CO2. Assim, busca-se catalisadores que promovam a seletividade do propeno. Compostos tipo hidrotalcitas estão sendo apontados como catalisadores de grande potencial para a reação. Portanto, o principal objetivo desse trabalho foi sintetizar precursores tipo hidrotalcitas (contendo íons Ni2+, Mg2+ e Al3+ e tereftalato, heptamolibdato e decavanadato como ânions de compensação) para serem testados na reação de desidrogenação oxidativa de propano. Esses precursores foram sintetizados com uma razão Al/(Al+Ni+Mg)=0,5, variando a razão de Ni/Mg. Além disso, realizou-se a troca iônica do tereftalato (TA) por heptamolibdato (Mo7O24) e decavanadato (V10O28). Esses compostos foram calcinados, obtendo-se assim, óxidos mistos de NiMgAl, NiMgAlMo e NiMgAlV que foram testados como catalisadores na reação de ODHP. Para a determinação das propriedades dos catalisadores foram usadas as técnicas de caracterização: DRX, TGA, volumetria de N2, TPR, Raman e FTIR e ICP. Os resultados indicaram que os materiais tipo hidrotalcita foram obtidos com sucesso. No caso dos precursores preparados por troca iônica a cristalinidade foi menor que os da série NiMgAl-TA. Estes mesmos precursores quando calcinados apresentaram áreas muito altas. Nas três séries, os precursores calcinados são constituídos por óxidos mistos como NiO, NiMoO4, Ni2V2O7 cristalinos e espécies de alumínio e magnésio não detectados na DRX. No teste catalítico de ODHP, observou-se que com o aumento da conversão diminuía a seletividade de propeno, para os óxidos mistos que não continham molibdênio. Os catalisadores da série molibdênio foram os que obtiveram melhor desempenho com altas seletividades, mesmo em altas conversões e a série de cujo precursor foi o tereftalato foi a que exibiu maiores conversões, mas com seletividades menores que da série de Mo

Trace metal (Cu, Zn, Pb, Cr and Cd) concentrations of three subfractions of organic matter from Lake Mariut sediments, Egypt

Trace elements associated with organic subfractions (humic, fulvic, and non-humic substances) were identified for seven core sediments from Lake Mariut, Egypt. Results indicated that the amounts of trace metals in humic acid and non-humic substances decreased in the following order: Zn>Cu>Pb>Cr>Cd, while in fulvic acid the order the order was Cu>Zn>Pb>Cr>Cd. There is a higher contribution of Zn, Pb, Cu and Cr in humic acid compared to fulvic acid in most samples. Slight changes in the amounts of cadmium bounded with humic and fulvic acids was also found.

Mg-Al-Mn-RE系合金组织与性能研究

利用金属型铸造制备了Mg-5Al-0.3Mn-xRE (x = 0~4, wt%，RE = Ce, Nd, Sm, Y和(CeLa)混合稀土)系列合金，研究了铸态合金的组织和力学性能。利用轧制和挤压技术对优化出的合金进行了变形加工处理，并研究了合金加工后的组织和力学性能。 对于铸态合金，稀土元素不仅可以细化合金的晶粒，而且形成不同类型的Al-RE化合物，含Ce的合金中生成Al11Ce3相，含Nd或Sm的合金中，主要生成Al11Nd3 (Al11Sm3)相和少量的Al2Nd (Al2Sm)相，含Y的合金中生成Al2Y相。另外，添加稀土可以改变Mg17Al12相的形貌，使其变得更加细小、弥散。添加适量的稀土可以明显提高铸态合金在室温和150℃下的力学性能，Mg-5Al-0.3Mn-1.5Ce, Mg-5Al-0.3Mn-2Nd和Mg-5Al-0.3Mn-2Sm合金在各自的体系中具有最佳的综合力学性能。合金力学性能提高的主要原因是细晶强化、Al-RE化合物第二相强化以及减弱Mg17Al12相对合金高温力学性能的不利影响。 对Mg-5Al-0.3Mn-(1.0, 1.5, 2.0)Ce，Mg-5Al-0.3Mn-2Nd，Mg-5Al-0.3Mn-1.5(CeLa)和Mg-5Al-0.3Mn-3Y合金在300-400℃下进行了热轧制或挤压变形，与铸态合金相比，轧制和挤压合金具有更高的力学性能。轧制合金的室温抗拉强度为290-340 MPa，较铸态合金提高约50％，屈服强度约为210-260 MPa，较铸态合金提高约2倍。挤压态合金的抗拉强度为260-270 MPa，屈服强度为160-190MPa，伸长率为20-22％；150℃的力学性能也得到了明显改善。 结合热力学计算、合金化元素之间的电负性差、化合物相的生成焓数据以及相图计算，阐述了稀土化合物相的生成机制，稀土元素与Al元素之间的电负性差大于其与Mg之间的电负性差，且Al-RE相的生成焓远低于Mg-RE和Mg-Al相的生成焓，因此在Mg-Al合金中加入RE后，RE优先与Al形成Al-RE化合物。从晶粒细化、化合物强化相的生成和演变、变形加工处理的位错交互作用等方面讨论了合金的强化机制，认为细晶强化、第二相强化及形变强化是提高合金力学性能的主要机制。

川西地区几种优势苔藓植株元素含量及其时空差异性

揭示苔藓植株元素含量及其时空差异性是深入开展利用苔藓植物指示环境和筛选理想监测藓种的科学基础。采用微波消解（ICP-AES）方法对九寨沟自然遗产地原始林景点停车场周围三个采样带：I为停车场植被小岛（PS），向外约120 m半径为II带（D120），再向外距离约1,000 m为III带（D1000）和3个方向上的大羽藓和毛尖青藓2种苔藓中13种元素（A1, S, Ca, P, Cu, Fe, K, Mg, Mn, Pb, Ni,Zn和Cd）含量进行了测定和比较，并对采自边坡方向（PS-3）上2005和2007年的4种苔藓植物（南木藓、大羽藓、平藓和厚角絹藓）也进行了13种元素含量的测定和比较。同时对九寨沟自然遗产地、黄龙自然遗产地、夹金山和梦笔山的冷杉原始林4个地区的3种苔藓中（大羽藓、锦丝藓和塔藓）的A1、Ca、Cu、Fe、K、Mg、P、Zn、C和N 10种元素含量进行测定和比较。 对大羽藓和毛尖青藓2种苔藓植物内13种元素的测定发现：1）同种苔藓对不同元素的富集能力不同。A1、Ca、K、Mg和P的元素含量在苔藓中的富集较其他元素的要高。2）不同种苔藓植物对同种元素的富集能力不同，毛尖青藓较大羽藓能够监测出更多的元素；对于被检测出的元素，毛尖青藓监测出的累积量大于大羽藓，其中累积量最大的元素是Ca为10 874.286 μg.g-1.year-1，最小的是Cu元素为5.438 μg.g-1.year-1。对05年和07年的平藓、大羽藓、南木藓和厚角絹藓元素含量的测定表明：元素在两年中的积累量是不同的。综合分析表明，苔藓生物监测方法可有效监测景点停车场机动车尾气中排放出的典型元素（如Cu、Pb、Ni、Zn、Cd等）含量，而毛尖青藓较大羽藓能更可靠的监测九寨沟自然遗产地单景点汽车尾气金属元素种类及其排放量。 对4个地区3种苔藓10种元素监测发现：1）Ca、Mg、Zn、K和Cu元素在黄龙地区的含量高于在其它地区的含量；P元素在梦笔山地区的含量为最高；Fe和Al元素在夹金山地区的含量高于在其它地区的含量。2）C元素在其它因素一致的情况下，进行不同年龄间的元素含量比较，结果显示元素含量在各年龄间并不存在明显的差异性；N元素含量与年龄的差异出现在黄龙林下及林窗的塔藓、九寨沟林下的锦丝藓及塔藓和梦笔山的塔藓中，而在锦丝藓中未出现元素含量与年龄的差异性；塔藓能检测出更多的元素种类其含量与年龄间存在显著差异，锦丝藓检测到的元素种类次之；除锦丝藓（锦丝藓在林窗中几乎检测不到元素含量与年龄间的差异性）外，其他两种藓在林窗中能检测出的元素种类大于在林下的检测种类。3）元素含量与生境间存在差异性的元素分别有：黄龙大羽藓中的Ca、P和Mg元素；九寨锦丝藓中的Zn元素；夹金山塔藓中的Al、Fe和Zn元素；梦笔山大羽藓中的Al、Fe和Mg元素及锦丝藓中的Ca元素。4）区域、年龄和生境因素对苔藓植株元素含量均达到了显著水平，但两两之间及三者之间的交互作用由于元素种类的不同存在差异。综合分析表明，苔藓植物中的元素含量受年龄、区域的影响较生境的更大。 The revelation of mosses elements content and its spatiotemporal differences is the scientific foundation of moss monitoring. To determine the feasibility of moss monitoring metal depositions derived from travel bus emiss ions in scenic spot, we collected one year-growth samples of two mosses Brachythecim piligerum and Thuidium cymbifolium with different distance (island center, 120m，1000m ) and different direction (north, south and east) far from parking site island from Yuanshilin Spot at Jiuzhaigou World Nature Heritage in the Western Sichuan of China and determined thirteen element （A1, S, Ca, P, Cu, Fe, K, Mg, Mn, Pb, Ni, Zn, Cd）contents by ICP-AES analysis method. And picked 4 kinds of mosses (Macrothamnium macrocarpu m（Reinw. etHornsch.）Fleisch.，Thuidium cymbifolium，Entodon concinnus (De Not.) Par., Neckera pennata) from the direction PS-3 in 2005 and 2007, determined 13 element contents. Collected 3 kinds of moss (Thuidium cymbifo lium, Actinothuidium Hookeri (Mitt.) and Hyolcomium splendens (Hedw.) from Jiuzhaigou natural heritage, Huanglong natural heritage, Mt. Jiajin and Mt. Mengbi in primeval forest with two habitat (undergrowth and forest gap), determined element contents of A1, Ca, Cu, Fe, K, Mg, P, Zn, C and N. We found that, 1) The elements content are difference in same type of moss. Content of A1, Ca, K, Mg and P are higher than others. 2) While the contents of A1, S, Ca, P, Cu, Fe, K and Zn had significant correlation with the different distances from parking site, the nearer the distance was, the more accumulation was; 2) Comparing to Thuidium cymbifolium, Brachythecium piligerum can test more elements which contents show the significant correlation with distances. And Brachythecium piligerum can have greater element accumulation than Thuidium cymbifolium. The element contents in two years (2005 and 2007) are different. The present study found that moss can reliably bio-indicate metal deposition from traffic emissions in one scenic spot and Brachythecium piligerum is a good moss for bio-indicating element content from traffic emissions at Jiuzhaigou World natural Heritage. Determined the 10 element contents in 4 areas through 3 kinds of moss we found that, 1) Ca, Mg, Zn, K and Cu element content is higher in the Huanglong area than in other areas, The P element content in Mt. Jiajin is higher than other areas, Fe and Al element content is higher in the Mt. Jiajin than in other areas. 2) The content of C had no significant correlation with age. As for N, this significant correlation found in Hyolcomium splendens (Hedw.) with 2 habitat in Huanglong, Actinothuidium Hookeri (Mitt.) and Hyolcomium splendens (Hedw.) with undergrowth in Jiuzhai, Hyolcomium splendens (Hedw.) in Mt. Mengbi. The types of elements which content showt he significant correlation are most in Hyolcomium splendens (Hedw.) and least in Thuidium cymbifolium. Except Actinothuidium Hookeri (Mitt.), the types of elements that content had significant correlation with age in forest gap are more than in undergrowth. 3) The elements which content had significant correlation with habitat are P, Ca and Mg in Thuidium cymbifolium in Huanglong, Zn in Actinothuidium Hookeri (Mitt.) in Jiuzhai, Al, Fe and Zn in Hyolcomium splendens (Hedw.) in Mt. Jiajin, in Mt. Mengbi Al, Fe and Mg in Thuidium cymbifolium and Ca in Actinothuidium Hookeri (Mitt.). 4）The region, the age and the habitat factor has coeffect element content. The correlationship between element contents and the age, the region is closer than habitat.

Effect of Nd on the microstructure, mechanical properties and corrosion behavior of die-cast Mg-4Al-based alloy

Die-cast Mg-4Al-0.4Mn-xNd(x = 0, 1, 2, 4 and 6 wt.%) magnesium alloys were prepared successfully and influences of Nd on the microstructure, mechanical properties and corrosion behavior of the Mg-4Al-0.4Mn alloy have been investigated. The results showed that with the addition of Nd binary Al2Nd phase and Al11Nd3 phase. which mainly aggregated along the grain boundaries, were formed, and the relative ratio of above two phases was in correlation with the Nd content in the alloy. Meanwhile, the grain sizes were greatly reduced with the increasing Nd content. It was found that due to the addition of Nd both the tensile properties and corrosion resistance were improved substantially.

Microstructure and mechanical properties of Mg-4Al-4Nd-0.5Zn-0.3Mn alloy

Mg-4Al-4Nd-0.5Zn-0.3Mn alloy was prepared by metal mould casting method. Microstructure, aging behavior, mechanical properties and fracture morphology of the alloy were investigated. The results showed that alpha-Mg, Al-11 Nd-3, Al2Nd and Mg-32(Al,Zn)(49) phases were the main phases of the as-cast alloy. And the long rod-like Al-11 Nd-3 phase was decomposed to granular Al2Nd through T6 heat treatment. The tensile strength was also enhanced by T6 treatment. The yield strength was increased by 17% and 21% at RT and 150 degrees C, respectively. It was mainly because that the precipitates were refined through T6 treatment and this became more benefit to hinder dislocations slipping.

The microstructure and mechanical properties of Mg-8Zn-8Al-4RE magnesium alloy

The Mg-8Zn-8Al-4RE (RE = mischmetal, mass%) magnesium alloy was prepared by using casting method. The microstructure and mechanical properties of as-cast alloy, solid solution alloy and aged alloy samples have been investigated. Optical microscopy, X-ray diffractometery and scanning electron microscope attached energy spectrometer were used to characterize the microstructure and phase composition for the alloy. Net shaped tau-Mg-32(Al,Zn)(49) phase was obtained at the grain boundary, and needle-like or blocky Al11RE3 phase disperses in grain boundary and alpha-Mg matrix. The tau-Mg-32(Al,Zn)(49) phase disappeared during solution treatment and a new phase of Al(2)CeZn2 formed during subsequent age treatment. The mechanical properties were performed by universal testing machine at room temperature, 150 degrees C and 200 degrees C, separately. The ultimate tensile strength of as-cast alloy is lower compared to an age treatment alloy at 200 degrees C for 12h. The strengths decreased with enhancing test temperature, but elongation has not been effect by age treatment.

稀土离子与牛血Cu(Zn)-SOD的作用

采用ESR、CD谱和荧光光谱研究了pH=6.3时六次甲基四胺-HCl缓冲溶液中LaCl_3和TbCl_3与Cu(Zn)-SOD的配位作用和结构。Cu(Zn)-SOD可增强Tb~(3+)的荧光发射,Tb~(3+)与Cu(Zn)-SOD有多个配位位置,其中有2个强结合位点,La~(3+)与Tb~(3+)可竞争Cu(Zn)…SOD上相同结合位点,77K下La~(3+)与Tb~(3+)使Cu(Zn)-SOD的Cu~(2+)活性中心的配位环境由菱形对称结构向轴对称结构转变,使Cu(Zn)-SOD的局部结构变松散,但对SOD酶活性基本无影响,表明稀土离子主要与酶蛋白分子中的酸性氨基酸羧基配位,对酶蛋白二级结构仅产生微弱扰动,对活性中心空间结构影响较小,基本不影响Cu(Zn)-SOD酶活性。