末次盛冰期以来江西大湖孢粉植被与环境演变

IEECAS SKLLQG

~(133)Sm的(EC+β~+)衰变和~(133)Pr的1.1s同质异能态

通过96 Ru( 4 0 Ca ,ln2p)反应 ,采用氦喷嘴带传输系统和X γ与γ γ符合测量方法 ,首次建议了133Sm的简单的 (EC + β+)衰变纲图 .由于Ru靶中含有98— 10 2 Ru的成分 ,同时产生了133Pr,并首次测定了133Pr的 1 1 / 2 - 同质异能态的寿命为( 1 .1± 0 .2 )s.用单粒子模型提取了131,133,135 ,137Pr的 1 1 / 2 - 同质异能态的约化跃迁几率的实验值 ,并与Weisscopf近似估计进行了比较 .

Primary design of stochastic cooling in CSRm

Based on several facts of CSRrn, such as the layout of the ring, the lattice parameters, exiting Schottky noise diagnosis equipment and fund, the primary stochastic cooling design of CSRm has been carried out. The optimum cooling time and the optimum cooling bandwidth axe obtained through simulation using the cooling function. The results indicate that the stochastic cooling is quite a powerful cooling method for CSRm. The comparison of the cooling effects of stochastic cooling and electron cooling in CSR are also presented. We can conclude that the combination of the two cooling methods on CSRrn will improve the beam cooling rate and quality beam greatly.

Pt-based anode catalysts for direct ethanol fuel cells

In the present work, several carbon supported PtSn and PtSnRu catalysts were prepared with different atomic ratios and tested in direct ethanol fuel cells (DEFC) operated at lower temperature (T=90 degreesC). XRD and TEM results indicate that all of these catalysts consist of uniform nano-sized particles of narrow distribution and the average particle sizes are always less than 3.0 nm. As the content of Sn increases, the Pt lattice parameter becomes longer. Single direct ethanol fuel cell tests were used to evaluate the performance of carbon supported PtSn catalysts for ethanol electro-oxidation. It was found that the addition of Sn can enhance the activity towards ethanol electro-oxidation. It is also found that a single DEFC of Pt/Sn atomic ratioless than or equal to2, "Pt1Sn1/C, Pt3Sn2/C, and Pt2Sn1/C" shows better performance than those with Pt3Sn1/C and Pt4Sn1/C. But even adopting the least active PtSn catalyst, Pt4Sn1/C, the DEFC also exhibits higher performance than that with the commercial Pt1Ru1/C, which is dominatingly used in PEMFC at present as anode catalyst for both methanol electro-oxidation and CO-tolerance. At 90 degreesC, the DEFC exhibits the best performance when Pt2Sn1/C is adopted as anode catalysts. This distinct difference in DEFC performance between the catalysts examined here is attributed to the so-called bifunctional mechanism and to the electronic interaction between Pt and Sn. It is thought that -OHads, Surface Pt active sites and the ohmic effect of PtSn/C catalyst determines the electro-oxidation activity of PtSn catalysts with different Pt/Sn ratios. (C) 2004 Elsevier B.V. All rights reserved.

半湿润农田杂草及施氮对夏玉米产量及氮素利用的影响

以土垫旱耕人为土为供试土壤,采用大田试验,研究了半湿润农田两种杂草处理方式下(成熟后期清除杂草-A区和苗期开始清除杂草-B区),不同施氮量对夏玉米产量及氮素利用效率的影响。结果表明,当施氮量为0、45、90、1351、80 kg/hm2时,B区玉米子粒产量比A区分别增加了8.7%、12.1%、9.4%、5.0%和12.5%;吸氮量分别增加了1.5、2.9、4.85、.2和4.3 kg/hm2。A区和B区全生育期0—100 cm土层矿质氮(Nmin)累积量变化趋势基本一致,但B区比A区变幅较大。当施氮量为45、90、135和180 kg/hm2时,B区氮肥利用率、氮肥农学利用率、氮肥生理利用率均高于A区。研究还发现,在A区,当施氮量为180 kg/hm2时,杂草干生物量最大,为1518.3 kg/hm2,不施氮时,杂草的生物量最低,为845.7 kg/hm2;杂草的吸氮量随施氮量的增加而增加。可见,清除玉米农田杂草不仅可以提高作物产量和氮肥利用率,而且在减少氮素损失方面具有一定作用。

基于贝塞尔曲线的WSN等值线绘制算法

从无线传感器网络(WSN)环境数值监测应用的实际需求出发,提出了一种应用于该类场景中的等值线绘制(CMBC)算法.CMBC算法基于图形学中常用的贝塞尔(Bezier)曲线理论,通过选择部分节点提供信息给网关节点绘制等值线.此方法有效解决了监测应用场景中对最终监测精度的需求与大量报告节点所引发的高流量负载和网络能耗之间的矛盾.仿真结果表明,CMBC算法和已有研究工作相比能够使用更少的汇报节点完成高精度等值线的绘制,因此CMBC算法能够节省节点的能量,延长网络的生存期.

A Simple and Inexpensive Method for Fabrication of Ultramicroelectrode Array and Its Application for the Detection of Dissolved Oxygen

Herein, we report a simple and inexpensive way for fabrication of ultra microelectrode arrays (UMEAs) and the relative characterization methods. The fabrication of UMEAs involves only a few steps of handwork. Since only metal wires and epoxy are used through the fabrication process, it is supposed to be a quite straightforward method for preparing UMEAs. A dissolved oxygen (DO) sensor based on UMEAs was constructed.

The optical spectroscopic properties of rare earth-activated barium orthophosphate in VUV-Vis range

The optical properties of rare earth ions-activated barium orthophosphate phosphors, Ba-3(PO4)(2):RE (RE = Ce3+, Sm3+, Eu3+, Eu2+, and Tb3+), were investigated in vacuum ultraviolet (VLTV)-Vis range. A band-band transition Of PO43- in Ba-3(PO4)(2) is observed in the region of 150-170 nm. The partial reduction of Eu3+ to Eu2+ was observed and confirmed by luminescent spectra under the VUV-UV excitation. It is proposed that the electronegative defects that formed by aliovalent substitution of Eu3+ on the Ba2+ site in the host are responsible for the reduction process.

Crystal growth and TG-DTA properties of K(2)Ln(NO3)(5).2H(2)O (Ln = La, Ce, Pr, Nd, Sm)

Single crystals of KLnN(Ln=La, Ce, Pr, Nd, Sm) can be grown in water solution with pH approximate to 1 similar to 2 at about 40 degrees C. Crystals of KLnN (Ln=La, Ce, Pr, Nd) are orthorhombic with space group Fdd2. KPrN crystal was grwon and its crystal structure was determined for the first time. The KPrN crystal parameters obtained by the direct method are as follows: a=21.411(3) Angstrom, b=11.2210(10)Angstrom, c=12.208(2) Angstrom, Z=6, R=0.0240. The TG-DTA curves of KLnN(Ln=La,Ce, Pr, Nd, Sm) demonstrate that the processes of dehydration, melt, irreversible phase transition and decomposition of NO3- take place in sequence with the temperature increasing(except KCN). There are three steps in the decomposition of NO3- in KLnN(Ln=La, Nd, Sm) while two steps in KLnN (Ln=Ce, Pr). K(2)Ln(NO3)(5). 2H(2)O are formed at about 225 degrees C by the reaction of the starting materials of KNO3 and Ln(NO3)(3). nH(2)O.

K_2Ln(NO_3)_5·2H_2O(Ln=La,Ce,Pr,Nd,Sm)的晶体生长和热重-差热分析研究

本文生长出了K2Ln（NO3）5.2H2O（Ln=La；Ce；Pr；Nd；Sm）的单晶，并对其进行了晶体结构及差热-热重分析研究．结果表明，K2Ln（NO3）5.2H2O（Ln=La；Ce；Pr；Nd）的晶体属正交晶系，Fdd2空间群．首次生长出KPrN单晶并用直接法解出其晶体结构．解得KPrN的晶胞参数为：a=11．2210（10）,b=21．411（3），c=12．208（2）,Z=6；R=0．0240．对KLnN加热，则依次出现脱水、熔化、不可逆相变和NO的分解过程（K2Ce（NO3）5·2H2O除外）K2Ln（NO3）5·2H2O（Ln＝La；Nd；Sm）的NO分三步分解，K2Ln（NO3）5·2H。O（Ln=Ce；Pr）的NO分两步分解·KNO3和Ln（NO3）3·nH2O的混合物在225℃左右生成K2Ln（NO3）5

Cure processing modeling and cure cycle simulation of epoxy-terminated poly(phenylene ether ketone) .1. DSC characterization of curing reaction

The curing reaction process of epoxy-terminated poly(phenylene ether ketone) (E-PEK) with 4,4'-diaminodiphenyl sulfone (DDS) and hexahydrophthalic acid anhydride (Nadic) as curing agents was investigated using isothermal differential scanning calorimetry (IDSC) and nonisothermal differential scanning calorimetry (DDSC) techniques. It was found that the curing reactions of E-PEK/DDS and E-PEK/Nadic are nth-order reactions but not autoaccelerating. The experimental results revealed that the curing reaction kinetics parameters measured from IDSC and DDSC are not equivalent. This means that, in the curing reaction kinetics model for our E-PEK system, both isothermal and nonisothermal reaction kinetics parameters are needed to describe isothermal and nonisothermal curing processes, The isothermal and nonisothermal curing processes were successfully simulated using this model. A new extrapolation method was suggested. On the basis of this method the maximum extent of the curing reaction (A(ult)) that is able to reach a certain temperature can be predicted. The A(ult) for the E-PEK system estimated by the new method agrees well with the results obtained from another procedure reported in the literature. (C) 1997 John Wiley & Sons, Inc.

Study on the Property of Vitamin B-12-Modified Electrode and its Electrocatalysis for the Reduction of Oxygen

It was found that vitamin B-12 could be strongly adsorpted on the anodized glassy carbon electrode to form a vitamin Thy-modified glassy carbon electrode. The modified electrode is stable in a wide pH range. The electrochemical characteristics of the modified electrode were studied in details. In addition, it was found that the reduction of oxygen could be catalyzed by the modified electrode to form H2O2. An EC mechanism was suggested for the process, and the follow up chemical reaction might he the rate determined step.

维生素B_(12)修饰电极及其催化氧还原性质的研究

发现维生素B12能吸附在经阳极化处理的玻碳电极上，从而制成稳定的维生素B12修饰玻碳电极．详细研究了此电极的电化学性质．并发现此修饰电极能有效地催化分子氧的二电子还原.

Synthesis and molecular structures of di- and trinuclear molybdenum complexes containing pyridine-2-thiolato (pyS) ligand

Dinuclear complexes [Mo-2(mu-pyS)(2)(CO)(4)(PPh(3))(2)] (1), [Mo-2(mu-pyS)(2)(CO)(5)(PPh(3))] (2) and a trace quality of trinuclear complex [Mo-3(mu-pyS)(2)(mu(3)-pyS)(2)(CO)(6)] (3) were obtained from the reaction of [Mo(CO)(3)(MeCN)(3)] with pyridine-2-thione (pySH) and PPh(3) in THF. The crystal structures of 1.2C(7)H(8) and 3.7 C7H8 have been determined by X-ray diffraction studies. Crystals of 1.2C(7)H(8) are monoclinic, space group C2/c and Z = 4, with a = 18.797(3), b = 11.143(4), c = 28.157(7) Angstrom, beta = 101.23(2)degrees. The structure was refined to R = 0.050 and Rw = 0.057 for 3146 observed reflections, Crystals of 3.7 C7H8 are monoclinic, space group P2(1)/a and Z = 4, with a = 13.912(2), b = 17.161(2), c = 15.577(3) Angstrom, beta = 101.17(1)degrees. The structure was refined to R = 0.046 and Rw = 0.051 for 4357 observed reflections. The molecule of 1 consists of two Mo(CO)(2)(PPh(3)) fragments linked by an Mo-Mo bond (2.974(2)Angstrom) and by two doubly-bridging pyS ligands. The compound 3 contains a bent open geometry of three molybdenum atoms (Mo(1)-Mo(2)-Mo(3) angle 122.99(3)degrees) linked by two Mo-Mo bonds (2.943(1) and 2.950(1) Angstrom) and by two doubly- and two triply-bridging pyS ligands.

THE SYNTHESIS AND CRYSTAL-STRUCTURE OF [LA(OH2)(5)(PHEN)(2)]CL-3-CENTER-DOT-4H(2)O-CENTER-DOT-PHEN

[La(OH2)(5)(phen)(2)]Cl-3 4H(2)O.phen is centric, Pnna, with a = 19.946(7), b = 16.458(5), c = 12.207(4)Angstrom and D-calc = 1.57 g cm(-3) for Z = 4. The La(III) ion resides on a crystallographic twofold axis and is coordinated to four nitrogen atoms (fr