An inverse design method for elliptical MRI magnets

An inverse, current density mapping (CDM) method has been developed for the design of elliptical cross-section MRI magnets. The method provides a rapid prototyping system for unusual magnet designs, as it generates a 3D current density in response to a set of target field and geometric constraints. The emphasis of this work is on the investigation of new elliptical coil structures for clinical MRI magnets. The effect of the elliptical aspect ratio on magnet performance is investigated. Viable designs are generated for symmetric, asymmetric and open architecture elliptical magnets using the new method. Clinically relevant attributes such as reduced stray field and large homogeneous regions relative to total magnet length are included in the design process and investigated in detail. The preliminary magnet designs have several novel features.

Current density mapping approach for design of clinical magnetic resonance imaging magnets

Novel current density mapping (CDM) schemes are developed for the design of new actively shielded, clinical magnetic resonance imaging (MRI) magnets. This is an extended inverse method in which the entire potential solution space for the superconductors has been considered, rather than single current density layers. The solution provides an insight into the required superconducting coil pattern for a desired magnet configuration. This information is then used as an initial set of parameters for the magnet structure, and a previously developed hybrid numerical optimization technique is used to obtain the final geometry of the magnet. The CDM scheme is applied to the design of compact symmetric, asymmetric, and open architecture 1.0-1.5 T MRI magnet systems of novel geometry and utility. A new symmetric 1.0-T system that is just I m in length with a full 50-cm diameter of the active, or sensitive, volume (DSV) is detailed, as well as an asymmetric system in which a 50-cm DSV begins just 14 cm from the end of the coil structure. Finally a 1.0-T open magnet system with a full 50-cm DSV is presented. These new designs provide clinically useful homogeneous regions and have appropriately restricted stray fields but, in some of the designs, the DSV is much closer to the end of the magnet system than in conventional designs. These new designs have the potential to reduce patient claustrophobia and improve physician access to patients undergoing scans. (C) 2002 Wiley Periodicals, Inc.

Mapping intertidal habitats and an evaluation of their conservation status in Queensland, Australia

The goal of biodiversity conservation has been described as the conservation of diversity at three levels: ecosystem, species and genetic diversity. Developing a representative system of marine protected areas (MPAs) is considered an effective way to achieve this goal in the marine environment. In the absence of detailed information relating to biological distributions there has been increasing use of biodiversity surrogates to determine MPA priorities at regional levels. The development of biodiversity surrogates at fine scales (i.e. habitats) will have an increasingly important role in the identification of sites that will contribute to a representative system of MPAs. This is because it will increase the likelihood that the system will adequately achieve biodiversity objectives by ensuring protection of a greater range of habitats and species. This article provides an explanation of an intertidal shoreline habitat surrogate used to describe 24,216km of Queensland's coastline. The protective status of intertidal habitats was evaluated to assist with designing a representative system of intertidal MPAs. (C) 2002 Elsevier Science Ltd. All rights reserved.

Combining the analyses of introgressive hybridisation and linkage mapping to investigate the genetic architecture of population divergence in the lake whitefish (Coregonus clupeaformis, Mitchill)

Adaptation and reproductive isolation, the engines of biological diversity, are still elusive when discussing the genetic bases of speciation. Namely, the number of genes and magnitude of selection acting positively or negatively on genomic traits implicated in speciation is contentious. Here, we describe the first steps of an ongoing research program aimed at understanding the genetic bases of population divergence and reproductive isolation in the lake whitefish (Coregonus clupeaformis). A preliminary linkage map originating from a hybrid cross between dwarf and normal ecotypes is presented, whereby some of the segregating AFLP markers were found to be conserved among natural populations. Maximum-likelihood was used to estimate hybrid indices from non-diagnostic markers at 998 AFLP loci. This allowed identification of the most likely candidate loci that have been under the influence of selection during the natural hybridisation of whitefish originating from different glacial races. As some of these loci could be identified on the linkage map, the possibility that selection of traits in natural populations may eventually be correlated to specific chromosomal regions was demonstrated. The future prospects and potential of these approaches to elucidate the genetic bases of adaptation and reproductive isolation among sympatric ecotypes of lake whitefish is discussed.

Mapping glider habitat in dry eucalypt forests for Montreal Process indicator 1.1: Fragmentation of forest types

Accurate habitat mapping is critical to landscape ecological studies such as required for developing and testing Montreal Process indicator 1.1e, fragmentation of forest types. This task poses a major challenge to remote sensing, especially in mixedspecies, variable-age forests such as dry eucalypt forests of subtropical eastern Australia. In this paper, we apply an innovative approach that uses a small section of one-metre resolution airborne data to calibrate a moderate spatial resolution model (30 m resolution; scale 1:50 000) based on Landsat Thematic Mapper data to estimate canopy structural properties in St Marys State Forest, near Maryborough, south-eastern Queensland. The approach applies an image-processing model that assumes each image pixel is significantly larger than individual tree crowns and gaps to estimate crown-cover percentage, stem density and mean crown diameter. These parameters were classified into three discrete habitat classes to match the ecology of four exudivorous arboreal species (yellowbellied glider Petaurus australis, sugar glider P. breviceps, squirrel glider P. norfolcensis , and feathertail glider Acrobates pygmaeus), and one folivorous arboreal marsupial, the greater glider Petauroides volans. These species were targeted due to the known ecological preference for old trees with hollows, and differences in their home range requirements. The overall mapping accuracy, visually assessed against transects (n = 93) interpreted from a digital orthophoto and validated in the field, was 79% (KHAT statistic = 0.72). The KHAT statistic serves as an indicator of the extent that the percentage correct values of the error matrix are due to ‘true’ agreement verses ‘chance’ agreement. This means that we are able to reliably report on the effect of habitat loss on target species, especially those with a large home range size (e.g. yellow-bellied glider). However, the classified habitat map failed to accurately capture the spatial patterning (e.g. patch size and shape) of stands with a trace or sub-dominance of senescent trees. This outcome makes the reporting of the effects of habitat fragmentation more problematic, especially for species with a small home range size (e.g. feathertail glider). With further model refinement and validation, however, this moderateresolution approach offers an important, cost eff e c t i v e advancement in mapping the age of dry eucalypt forests in the region.

Inheritance and mapping of 11 avirulence genes in Phytophthora sojae

Two new crosses involving four races (races 7, 16, 17, and 25) of the soybean root and stem rot pathogen Phytophthora sojae were established (7/16 cross; 17/25 cross). An F-2 Population derived from each cross was used to determine the genetic basis of avirulence towards 11 different resistance genes in soybean. Avirulence was found to be dominant and determined by a single locus for Avr1b, 1d, 1k, 3b, 4, and 6, as expected for a simple gene-for-gene model. We also observed several cases of segregation, inconsistent with a single dominant gene being solely responsible for avirulence, which suggests that the genetic background of the different crosses can affect avirulence. Avr4 and 6 cosegregated in both the 7/16 and 17/25 crosses and, in the 7/16 cross, Avr1b and 1k were closely linked. Information from segregating RAPD, RFLP, and AFLP markers screened on F-2 progeny from the two new crosses and two crosses described previously (a total of 212 F-2 individuals, 53 from each cross) were used to construct an integrated genetic linkage map of P. sojae. This revised genetic linkage map consists of 386 markers comprising 35 RFLP, 236 RAPD, and 105 AFLP markers, as well as 10 avirulence genes. The map is composed of 21 major linkage groups and seven minor linkage groups covering a total map distance of 1640.4 cM. (C) 2002 Elsevier Science (USA). All rights reserved.

Mapping Gray's model of personality onto the Eysenck Personality Profiler (EPP)

The aim of this study was to determine how well Gray's model of personality [Gray, J.A. (1982). The neuropsychology of anxiety: an enquiry into the functions of the septo-hippocampal system. Oxfords: Oxford University Press, Gray, J.A. (1987). The psychology of fear and stress. Cambridge: Cambridge University Press], as measured by the Gray Wilson Personality Questionnaire (GWPQ), can provide a full description of personality as measured by the primary scales of the Eysenck Personality Profiler (EPP) and the type scales of the short version or the EPQ-R. Factor analysis of the GWPQ the Anxiety and linpulsivity scales of the EPP and the Learning Styles Questionnaire (LSQ) showed that the GWPQ seemed to measure general activation and inhibition factors, but not the finer features of Gray's theory. When the GWPQ scales were regressed against each scale of the EPP., it was round that they generally provide only a reasonable explanation of the EPP primary scales. It is concluded that the GWPQ measures general propel-ties of Gray's model, that the linpulsivity and Anxiety scales of the EPP also scent related to the GWPQ scales, and that Gray's model of personality provides only a partial explanation of personality in general. (C) 2002 Published by Elsevier Science Ltd. All rights reserved.

Evaluating Australia's National Medicines Policy using geographical mapping

Background: There has been a proliferation of quality use of medicines activities in Australia since the 1990s. However, knowledge of the nature and extent of these activities was lacking. A mechanism was required to map the activities to enable their coordination. Aims: To develop a geographical mapping facility as an evaluative tool to assist the planning and implementation of Australia's policy on the quality use of medicines. Methods: A web-based database incorporating geographical mapping software was developed. Quality use of medicines projects implemented across the country was identified from project listings funded by the Quality Use of Medicines Evaluation Program, the National Health and Medical Research Council, Mental Health Strategy, Rural Health Support, Education and Training Program, the Healthy Seniors Initiative, the General Practice Evaluation Program and the Drug Utilisation Evaluation Network. In addition, projects were identified through direct mail to persons working in the field. Results: The Quality Use of Medicines Mapping Project (QUMMP) was developed, providing a Web-based database that can be continuously updated. This database showed the distribution of quality use of medicines activities by: (i) geographical region, (ii) project type, (iii) target group, (iv) stakeholder involvement, (v) funding body and (vi) evaluation method. At September 2001, the database included 901 projects. Sixty-two per cent of projects had been conducted in Australian capital cities, where approximately 63% of the population reside. Distribution of projects varied between States. In Western Australia and Queensland, 36 and 73 projects had been conducted, respectively, representing approximately two projects per 100 000 people. By comparison, in South Australia and Tasmania approximately seven projects per 100 000 people were recorded, with six per 100 000 people in Victoria and three per 100 000 people in New South Wales. Rural and remote areas of the country had more limited project activity. Conclusions: The mapping of projects by geographical location enabled easy identification of high and low activity areas. Analysis of the types of projects undertaken in each region enabled identification of target groups that had not been involved or services that had not yet been developed. This served as a powerful tool for policy planning and implementation and will be used to support the continued implementation of Australia's policy on the quality use of medicines.

Measuring range of active cervical rotation in a position of full head flexion using the 3D Fastrak measurement system: an intra-tester reliability study

Most external assessments of cervical range of motion assess the upper and lower cervical regions simultaneously. This study investigated the within and between days reliability of the clinical method used to bias this movement to the upper cervical region, namely measuring rotation of the head and neck in a position of full cervical flexion. Measurements were made using the Fastrak measurement system and were conducted by one operator. Results indicated high levels of within and between days repeatability (range of ICC2,1 values: 0.85-0.95). The ranges of axial rotation to right and left, measured with the neck positioned in full flexion, were approximately 56% and 50%, respectively of total cervical rotation, which relates well to the proportional division of rotation in the upper and lower cervical regions. These results suggest that this method of measuring rotation would be appropriate for use in subject studies where movement dysfunction is present in the upper cervical region, such as those with cervicogenic headache. (C) 2003 Elsevier Science Ltd. All rights reserved.

The modeling of turbulent reactive flows based on multiple mapping conditioning

A new modeling approach-multiple mapping conditioning (MMC)-is introduced to treat mixing and reaction in turbulent flows. The model combines the advantages of the probability density function and the conditional moment closure methods and is based on a certain generalization of the mapping closure concept. An equivalent stochastic formulation of the MMC model is given. The validity of the closuring hypothesis of the model is demonstrated by a comparison with direct numerical simulation results for the three-stream mixing problem. (C) 2003 American Institute of Physics.

Prospects for whole genome linkage disequilibrium mapping in domestic dog breeds

Linkage disequilibrium (LD) mapping is commonly used as a fine mapping tool in human genome mapping and has been used with some success for initial disease gene isolation in certain isolated inbred human populations. An understanding of the population history of domestic dog breeds suggests that LID mapping could be routinely utilized in this species for initial genome-wide scans. Such an approach offers significant advantages over traditional linkage analysis. Here, we demonstrate, using canine copper toxicosis in the Bedlington terrier as the model, that LID mapping could be reasonably expected to be a useful strategy in low-resolution, genome-wide scans in pure-bred dogs. Significant LID was demonstrated over distances up to 33.3 cM. It is very unlikely, for a number of reasons discussed, that this result could be extrapolated to the rest of the genome. It is, however, consistent with the expectation given the population structure of canine breeds and, in this breed at least, with the hypothesis that it may be possible to utilize LID in a genome-wide scan. In this study, LD mapping confirmed the location of the copper toxicosis in Bedlington terrier gene (CT-BT) and was able to do so in a population that was refractory to traditional linkage analysis.

Mapping the royal road and other hierarchical functions

In this paper we present a technique for visualising hierarchical and symmetric, multimodal fitness functions that have been investigated in the evolutionary computation literature. The focus of this technique is on landscapes in moderate-dimensional, binary spaces (i.e., fitness functions defined over {0, 1}(n), for n less than or equal to 16). The visualisation approach involves an unfolding of the hyperspace into a two-dimensional graph, whose layout represents the topology of the space using a recursive relationship, and whose shading defines the shape of the cost surface defined on the space. Using this technique we present case-study explorations of three fitness functions: royal road, hierarchical-if-and-only-if (H-IFF), and hierarchically decomposable functions (HDF). The visualisation approach provides an insight into the properties of these functions, particularly with respect to the size and shape of the basins of attraction around each of the local optima.

Mapping the Obama administration's response to the Arab Spring

When the Arab Spring broke out, the United States was in a quandary over how to handle the crisis in its attempt to balance its moral obligations and ideals without undercutting its strategic interests and those of its close allies. Flaws in US diplomatic approach have contributed to one of the most serious foreign policy crisis for a US administration to date with consequential upheaval and erosion of the US-built balance of power. The reactions and policy responses of the Obama administration highlight the difficulties in grasping with the new reality in the Middle East and in enunciating a policy platform that could combine American interests and values.

Piezoresistive sensors for force mapping of hip-prostheses

The success of artificial prosthetic replacements depends on the fixation of the artificial prosthetic component after being implanted in the thighbone. The materials for fixation are subject to mechanical stresses, which originate permanent deformations, incipient cracks and even fatigue fractures. This work shows the possibility of monitoring the mechanical stress over time in prosthesis. In this way, highly sensitive silicon thin-film piezoresistive sensors were developed attached to prosthesis and their results compared with commercial strain gauge sensors. Mechanical stress-strain experiments were performed in compressive mode, during 10,000 cycles. Experimental data was acquired at mechanical vibration frequencies of 0.5 Hz, 1 Hz and 5 Hz, and sent to a computer by means of a wireless link. The results show that there is a decrease in sensitivity of the thin-film silicon piezoresistive sensors when they are attached to the prosthesis, but this decrease does not compromise its monitoring performance. The sensitivity, compared to that of commercial strain gauges, is much larger due to their higher gauge factors (-23.5), when compared to the GFs of commercial sensors (2).