干旱对沙棘休眠、萌芽期内源激素及萌芽特性的影响

以 2a生中国沙棘为试验材料 ,研究了土壤干旱胁迫下沙棘苗木水分生理状况 ,内源GA1 3 及ABA水平与萌芽率的关系 ,结果表明 :土壤干旱胁迫导致苗体含水量、水势、自由水含量下降 ,显著提高冬季休眠与春季萌动期的内源ABA水平而降低内源GA1 3 含量 ,GA1 3 ABA降低 ,较晚达到萌动所需的调控阈值 ,萌芽延迟。重度胁迫下苗木延迟达 2 5d且萌芽后生长缓慢。长期土壤中度干旱条件下沙棘苗萌芽期亦略有延迟 ,萌芽后生长略有抑制

Mo掺杂对高纯Ce_(1-x)Nd_xO_(2-x/2)(x=0.10,0.15)体系烧结温度及晶界电性能的影响

用柠檬酸硝酸盐法制备高纯Ce1-xNdxO2-x/2(x=0.10,0.15)固溶体,加入摩尔分数为5%的Mo,研究了Mo掺杂对烧结温度、结构及电性能的影响.通过X射线衍射、电感偶合等离子体和场发射扫描电镜等手段对氧化物进行了结构表征,采用交流阻抗谱测试其电性能.柠檬酸硝酸盐法制备的前驱体经1450℃烧结24 h得到致密度大于96%的陶瓷材料;加入5%Mo,在1250℃下烧结8 h即可达到理想的致密度(>95%).加入Mo在烧结过程中可加快晶界迁移,促进晶粒生长,显著提高了晶界电导率.在600℃时Ce0.85Nd0.15O1.925的晶界电导率为2.56 S/m,加入Mo后材料的电导率增加到5.62 S/m.

Glucose biosensor based on gold nanoparticle-catalyzed luminol electrochemiluminescence on a three-dimensional sol-gel network

An electrochemiluminescent glucose biosensor was proposed based on gold nanoparticle-catalyzed luminol electrochemiluminescence (ECL). Gold nanoparticles were self-assembled onto silica sol-gel network, and then glucose oxidase was adsorbed on the surface of gold nanoparticles. The surface assembly process and the electrochemistry and ECL behaviors of the biosensor were investigated. The assembled gold nanoparticles could efficiently electrocatalyze luminol ECL ECL intensity of the biosensor depended on scan rate, luminol concentration, and size of gold nanoparticles.

CeO_2含量对Nd_2Ce_xO_(3+2x)热障涂层性能的影响

采用高温固相法合成了Nd2CexO3+2x(x=2.0,2.25,2.5,2.75,3.0)复合氧化物,在高温合金基体上采用等离子喷涂制备了该材料热障涂层。XRD分析结果表明Nd2CexO3+2x粉末和涂层均为立方萤石晶体结构。考察了CeO2含量对Nd2CexO3+2x的力学性能(弹性模量、维氏硬度和断裂韧性)和等离子喷涂涂层在1250℃抗热震性能的影响。随着CeO2含量增加,材料的弹性模量降低,维氏硬度和断裂韧性提高。通过提高初始粉末中CeO2的含量,获得了组成接近化学计量比Nd2Ce2O7的涂层,涂层的抗热震性能增强,热循环次数达到1000次以上。Nd2CexO3+2x涂层的失效原因主要是:与金属基体之间...

Preparation and characterization of W-Type hexaferrite doped with La3+

A series of W-type ferrites with the composition of Ba1-xLaxCo2Fe16O27 (where, x = 0.0, 0.05, 0.10, 0.15, 020 and 0.25) were prepared by solid-state reaction method. The structure transformations of the ferrites were examined by XRD, DTA-TG and XPS, and the microwave-absorbing properties were investigated by evaluating the permeability and permittivity of materials (mu(r), epsilon(r)). The results showed that the phase-transition temperature increased with the addition of La2+ content, and a single-phase was formed at 1250 degrees C at last. Microwave properties were obviously improved as a result of the substitution of La3+ for Ba2+ at the frequency range of 0.5 similar to 18.0 GHz.

Grain boundary conductivity of high purity neodymium-doped ceria nanosystem with and without the doping of molybdenum oxide

Solid solutions of Ce1-xNdxO2-x/2 (0.05 <= x <= 0.2) and (Ce1-xNdx)(0.95)MO0.05O2-delta (0.05 <= x <= 0.2) have been synthesized by a modified sol-gel method. Both materials have very low content of SiO2 (similar to 27 ppm). Their structures and ionic conductivities were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM) and electrochemical impedance spectroscopy (M). The XRD patterns indicate that these materials are single phases with a cubic fluorite structure. The powders calcined at 300 degrees C with a crystal size of 5.7 nm have good sinterability, and the relative density could reach above 96% after being sintered at 1450 degrees C. With the addition Of MoO3, the sintering temperature could be decreased to 1250 degrees C. Impedance spectroscopy measurement in the temperature range of 250-800 degrees C indicates that a sharp increase of conductivity is observed when a small amount of Nd2O3 is added into ceria, of which Ce0.85Nd0.15O1.925 (15NDC) shows the highest conductivity. With the addition of a small amount Of MoO3, the grain boundary conductivity of 15NDC at 600 degrees C increases from 2.56 S m(-1) to 5.62 S m(-1).

Fabrication, patterning and luminescence properties of X-2-Y2SiO5 : A (A = Eu3+, Tb3+, Ce3+) phosphor films via sol-gel soft lithography

X-2-y(2)SiO(5):A (A = Eu3+, Tb3+, Ce3+) phosphor films and their patterning were fabricated by a sol-gel process combined with a soft lithography. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), atomic force microscopy (AFM), scanning electron microscopy (SEM) optical microscopy and photoluminescence (PL) were used to characterize the resulting films. The results of XRD indicated that the films began to crystallize at 900 degreesC with X-1-Y2SiO5, which transformed completely to X-2-Y2SiO5 at 1250 degreesC. Patterned thin films with different band widths (5 pin spaced by 5 pm and 16 pm spaced by 24 pm) were obtained by a soft lithography technique (micromoulding in capillaries, MIMIC). The SEM and AFM study revealed that the nonpattemed phosphor films were uniform and crack free, and the films mainly consisted of closely packed grains with an average size of 350 run. The doped rare earth ions (A) showed their characteristic emissions in X-2-Y2SiO5 phosphor films, i.e., D-5(0)-F-7(J) (J = 0, 1, 2,3,4) for Eu3+, D-5(3), (4)-F-7(J) (J = 6, 5, 4, 3) for Tb3+ and 5d (D-2)-4f (F-2(2/5),(2/7)) for Ce3+, respectively. The optimum doping concentrations for EU3+, Tb3+ were determined to be 13 and 8 mol% of Y3+ in X-2-Y2SiO5 films, respectively.

Thermal stability of double-ceramic-layer thermal barrier coatings with various coating thickness

Double-ceramic-layer (DCL) coatings with various thickness ratios composed of YSZ (6-8 wt.% Y2O3 + ZrO2) and lanthanum zirconate (LZ, La2Zr2O7) were produced by the atmospheric plasma spraying. Chemical stability of LZ in contact with YSZ in DCL coatings was investigated by calcining powder blends at different temperatures. No obvious reaction was observed when the calcination temperature was lower than 1250 degrees C, implying that LZ and YSZ had good chemical applicability for producing DCL coating. The thermal cycling test indicate that the cycling lives of the DCL coatings are strongly dependent on the thickness ratio of LZ and YSZ, and the coatings with YSZ thickness between 150 and 200 mu m have even longer lives than the single-layer YSZ coating. When the YSZ layer is thinner than 100 mu m, the DCL coatings failed in the LZ layer close to the interface of YSZ layer and LZ layer. For the coatings with the YSZ thickness above 150 mu m, the failure mainly occurs at the interface of the YSZ layer and the bond coat.

直接甲醇燃料电池的耐甲醇阴极电催化剂炭载四羧基酞菁钴的研究

比较了甲醇对 Pt/C和炭载四羧基酞菁钴 (Co Pc Tc/C)催化氧还原性能的影响 .结果表明 ,甲醇使Pt/C催化氧还原的性能严重降低 ,而对经 80 0℃热处理的 Co Pc Tc/C(Co Pc Tc/C-80 0 )基本没有影响 ;并且Co Pc Tc/C-80 0催化氧还原的性能优于经其它温度热处理的 Co Pc Tc/C,Co Pc Tc/C-80 0是一种较好的直接甲醇燃料电池的耐甲醇阴极电催化剂 .XPS结果表明 ,Co Pc Tc/C-80 0的活性位可能是含 Co N4结构的物质和零价 Co的混合物.

Red light-emitting diodes based on rare earth complex Eu (TTA)(4)C5H5NC16H33

A thin film electroluminescence cell with the structure of ITO/PPV/PVK:Eu(TTA)(4)C5H5NC16H33:PBD/Alq(3)/Al has been fabricated. Red emission with a very sharp spectral band at 614nm was observed and a maximum luminance of 20cd . m(-2) at 36V was obtained from the spin-coated device. The full width at half maximum of luminescent spectrum is less than 10nm.

A new high efficiency green luminescent material - the system Al2O3-B2O3 containing Ce3+ and Tb3+ ions

To obtain high efficiency luminescent materials, the system Al2O3-B2O3 containing Ce3+ and Tb3+ ions with variation of B2O3-content, has been prepared by Al2O3, H3BO3, CeO2 and Tb4O7 under reducing atmosphere at 1250(j)ae. It is notable that the brightness of the sample with appropriate composition is similar to that of commercial phosphorous containing Ce3+ and Tb3+, indicating that a new high efficency green luminescent material was obtained with appropriate B2O3-content.

Synthesis and structure of alpha-B-Keggin type heteropoly complex K5H[Co-4(VW9O33)(2)]center dot 5H(2)O

A new complex K5H[Co-4(VW9O33)(2)]. 5H(2)O was prepared and its structure was determined by X - ray diffraction analysis. The anion has alpha - beta - Keggin structure. Two (VW9O33)(7-) moieties (alpha - B isomers) are linked via four Co(11)O-6 groups. The single crystal of the title complex is monoclinic P2(1/n) with a = 1.2307(3) nm, b = 2.1250(4) nm, c = 1.5817(3) nm, beta = 91.86(3)degrees, V = 4.1343 (14) nm(3), R = 0.0895, R-w = 0.2180.

α-B-Keggin型杂多化合物K_5H[Co_4(VW_9O_(33))_2]·5H_2O的合成和结构

合成了新化合物K_5H[Co_4(VW_9O_(33))·5H_2O,并运用IR,UV-ViS,DTA和单晶X射线衍射对其结构进行了表征.测定结果证实标题化合物具有α-B-Keggin型结构,两个(VW_9O_(33)~(7-)结构单元由四个Co(Ⅱ)O_6 八面体连接.杂多化合物属单斜晶系P2_(1/n),a=1.2307(3)nm,b=2.1250(4)nm,c=1.5817(3)nm,β=91.86(3)°,V=4.1343(14)nm~3,R=0.0895,R_w=0.2180.

Sm~(3+)在硼酸盐玻璃中的发光及Bi~(3+)对Sm~(3+)的敏化作用

早在六十年代,人们为了寻找较好的激光玻璃,曾对Sm~(3+)离子掺杂的玻璃中的光谱进行过研究。为了探寻新型的激光,发光玻璃,又进一步研究了Sm~(3+)在玻璃中的发光和敏化。我们以寻找一种高亮度,低成本的发光玻璃为目的,研究了基质玻璃组成,敏化离子及其浓度对Sm~(3+)发光性质的影响。 选择B_2O_3-BaO-M_mO_n(M_mO_n=Li_2O,Na_2O,K_2O,MgO,CaO,SrO)玻璃体系,所用原料的纯度皆为分析纯以上,用陶瓷坩埚在1250℃掺杂氧化钐(纯度均大于99％),玻璃的荧光谱和激发光谱,用MPF-4型荧光分光光度计测定。