Practical Algorithms For Mean Velocity Estimation In Pulse Doppler Weather Radars Using A Small Number Of Samples

Doppler weather radars with fast scanning rates must estimate spectral moments based on a small number of echo samples. This paper concerns the estimation of mean Doppler velocity in a coherent radar using a short complex time series. Specific results are presented based on 16 samples. A wide range of signal-to-noise ratios are considered, and attention is given to ease of implementation. It is shown that FFT estimators fare poorly in low SNR and/or high spectrum-width situations. Several variants of a vector pulse-pair processor are postulated and an algorithm is developed for the resolution of phase angle ambiguity. This processor is found to be better than conventional processors at very low SNR values. A feasible approximation to the maximum entropy estimator is derived as well as a technique utilizing the maximization of the periodogram. It is found that a vector pulse-pair processor operating with four lags for clear air observation and a single lag (pulse-pair mode) for storm observation may be a good way to estimate Doppler velocities over the entire gamut of weather phenomena.

Incremental-angle and angular velocity estimation using a star sensor

A method is described for estimating the incremental angle and angular velocity of a spacecraft using integrated rate parameters with the help of a star sensor alone. The chief advantage of this method is that the measured stars need not be identified, whereas the identification of the stars is necessary in earlier methods. This proposed estimation can be carried out with all of the available measurements by a simple linear Kalman filter, albeit with a time-varying sensitivity matrix. The residuals of estimated angular velocity by the proposed spacecraft incremental-angle and angular velocity estimation method are as accurate as the earlier methods. This method also enables the spacecraft attitude to be reconstructed for mapping the stars into an imaginary unit sphere in the body reference frame, which will preserve the true angular separation of the stars. This will pave the way for identification of the stars using any angular separation or triangle matching techniques applied to even a narrow field of view sensor that is made to sweep the sky. A numerical simulation for inertial as well as Earth pointing spacecraft is carried out to establish the results.

Shear wave velocity estimation in the metropolitan area of Málaga (S Spain)

We carry out a seismic noise study based on array measurements at three sites in the Málaga basin, South Spain, for the further estimation of shear wave velocity profiles. For this purpose, we use both the H/V method and the f–k technique in order to characterize the different materials present in the zone, i.e., Quaternary sediments and Pliocene sedimentary rocks above the bedrock. The H/V analysis shows frequency peaks going from 1 Hz, in areas close to the border of the basin, to 0.3 Hz in places located toward the center of the formation. The f–k analysis allows obtaining the dispersion curves associated with each site and subsequently, estimating the Vs profiles by inversion of the respective group velocities. In this way, the basin basement can be characterized by S-wave velocities greater than 2000 m/s. Regarding the basin fill, it is divided into three layers defined by different wave velocity intervals. The shallowest one is featured by velocities ranging from 150 to 400 m/s and comprises the Quaternary sediments, while velocities going from 550–700 to1200–1600 m/s characterize the two underlying layers composed by Pliocene sediments. Finally, the information provided by the three Vs profiles is integrated in a 2D cross-section of the basin to have a spatial view of its sedimentary structure. The results obtained here, in addition to providing useful information about the infill of the basin near the metropolitan area of Málaga, will be very helpful for future seismic zonation studies in the region.

Vertical infrastructure inspection using a quadcopter and shared autonomy control

This paper presents a shared autonomy control scheme for a quadcopter that is suited for inspection of vertical infrastructure — tall man-made structures such as streetlights, electricity poles or the exterior surfaces of buildings. Current approaches to inspection of such structures is slow, expensive, and potentially hazardous. Low-cost aerial platforms with an ability to hover now have sufficient payload and endurance for this kind of task, but require significant human skill to fly. We develop a control architecture that enables synergy between the ground-based operator and the aerial inspection robot. An unskilled operator is assisted by onboard sensing and partial autonomy to safely fly the robot in close proximity to the structure. The operator uses their domain knowledge and problem solving skills to guide the robot in difficult to reach locations to inspect and assess the condition of the infrastructure. The operator commands the robot in a local task coordinate frame with limited degrees of freedom (DOF). For instance: up/down, left/right, toward/away with respect to the infrastructure. We therefore avoid problems of global mapping and navigation while providing an intuitive interface to the operator. We describe algorithms for pole detection, robot velocity estimation with respect to the pole, and position estimation in 3D space as well as the control algorithms and overall system architecture. We present initial results of shared autonomy of a quadrotor with respect to a vertical pole and robot performance is evaluated by comparing with motion capture data.

Kalman filtering for positioning and heading control of ships and offshore rigs

In this article, we have described the main components of a ship motion-control system and two particular motion-control problems that require wave filtering, namely, dynamic positioning and heading autopilot. Then, we discussed the models commonly used for vessel response and showed how these models are used for Kalman filter design. We also briefly discussed parameter and noise covariance estimation, which are used for filter tuning. To illustrate the performance, a case study based on numerical simulations for a ship autopilot was considered. The material discussed in this article conforms to modern commercially available ship motion-control systems. Most of the vessels operating in the offshore industry worldwide use Kalman filters for velocity estimation and wave filtering. Thus, the article provides an up-to-date tutorial and overview of Kalman-filter-based wave filtering.

基于内部传感器的轮式移动机器人运动速度估计

讨论了在无速度传感器的情况下轮式移动机器人的速度估计问题,采用了加速度传感器和位置传感器的输出实时估计轮式移动机器人速度,并用一种按加速度扰动调整权值的方法融合来自不同传感器的数据。实验验证了方法的有效性

叠前时间偏移：各向异性、多次波衰减及应用

At present, in order to image complex structures more accurately, the seismic migration methods has been developed from isotropic media to the anisotropic media. This dissertation develops a prestack time migration algorithm and application aspects for complex structures systematically. In transversely isotropic media with a vertical symmetry axis (VTI media), the dissertation starts from the theory that the prestack time migration is an approximation of the prestack depth migration, based on the one way wave equation and VTI time migration dispersion relation, by combining the stationary-phase theory gives a wave equation based VTI prestack time migration algorithm. Based on this algorithm, we can analytically obtain the travel time and amplitude expression in VTI media, as while conclude how the anisotropic parameter influence the time migration, and by analyzing the normal moveout of the far offset seismic data and lateral inhomogeneity of velocity, we can update the velocity model and estimate the anisotropic parameter model through the time migration. When anisotropic parameter is zero, this algorithm degenerates to the isotropic time migration algorithm naturally, so we can propose an isotopic processing procedure for imaging. This procedure may keep the main character of time migration such as high computational efficiency and velocity estimation through the migration, and, additionally, partially compensate the geometric divergence by adopting the deconvolution imaging condition of wave equation migration. Application of this algorithm to the complicated synthetic dataset and field data demonstrates the effectiveness of the approach. In the dissertation we also present an approach for estimating the velocity model and anisotropic parameter model. After analyzing the velocity and anisotropic parameter impaction on the time migration, and based on the normal moveout of the far offset seismic data and lateral inhomogeneity of velocity, through migration we can update the velocity model and estimate the anisotropic parameter model by combining the advantages of velocity analysis in isotropic media and anisotropic parameter estimation in VTI media. Testing on the synthetic and field data, demonstrates the method is effective and very steady. Massive synthetic dataset、2D sea dataset and 3D field datasets are used for VTI prestack time migration and compared to the stacked section after NMO and prestack isotropic time migration stacked section to demonstrate that VTI prestack time migration method in this paper can obtain better focusing and less positioning errors of complicated dip reflectors. When subsurface is more complex, primaries and multiples could not be separated in the Radon domain because they can no longer be described with simple functions (parabolic). We propose an attenuating multiple method in the image domain to resolve this problem. For a given velocity model，since time migration takes the complex structures wavefield propagation in to account, primaries and multiples have different offset-domain moveout discrepancies, then can be separated using techniques similar to the prior migration with Radon transform. Since every individual offset-domain common-reflection point gather incorporates complex 3D propagation effects, our method has the advantage of working with 3D data and complicated geology. Testing on synthetic and real data, we demonstrate the power of the method in discriminating between primaries and multiples after prestack time migration, and multiples can be attenuated in the image space considerably.

波动方程叠前深度偏移辛算法及速度建模

On 70~(th) SEG Annual meeting, many author have announced their result on the wave equation prestack depth migration. The methods of the wave-field imaging base on wave equation becomes mature and the main direction of seismic imaging. The direction of imaging the complex media has been the main one of the projects that the national "85" and "95" reservoir geophysics key projects and "Knowledge innovation key project of Chinese Academy of Science" have been supported. Furthermore, we began the study for special oil field situation of our nation with the international research groups. Under the background, the author combined the thoughts of symplectic with wave equation pre-stack depth migration, and develops and efficient wave equation pre-stack depth migration method. The purpose of this work is to find out a way to imaging the complex geological goals of Chinese oilfields and form a procedure of seismic data processing. The paper gives the approximation of one way wave equation operator, and shows the numerical results. The comparisons have been made between split-step phase method, Kirchhoff and Ray+FD methods on the pulse response, simple model and Marmousi model. The results shows that the method in this paper has an higher accuracy. Four field data examples have also be given in this paper. The results of field data demonstrate that the method can be usable. The velocity estimation is an important part of the wave equation pre-stack depth migration. A parallel velocity estimation program has been written and tested on the Beowulf clusters. The program can establish a velocity profile automatically. An example on Marmousi model has shown in the third part of the paper to demonstrate the method. Another field data was also given in the paper. Beowulf cluster is the converge of the high performance computer architecture. Today, Beowulf Cluster is a good choice for institutes and small companies to finish their task. The paper gives some comparison results the computation of the wave equation pre-stack migration on Beowulf cluster, IBM-SP2 (24 nodes) in Daqing and Shuguang 3000, and the comparison of their prize. The results show that the Beowulf cluster is an efficient way to finish the large amount computation of the wave equation pre-stack depth migration, especially for 3D.

辛格式波动方程叠前深度偏移及速度建模

On 70~(th) SEG Annual meeting, many author have announced their result on the wave equation pre-stack depth migration. The methods of the wave-field imaging base on wave equation becomes mature and the main direction of seismic imaging. The direction of imaging the complex media has been the main one of the projects that the national "85" and "95" reservoir geophysics key projects and "Knowledge innovation key project of Chinese Academy of Science" have been supported. Furthermore, we began the study for special oil field situation of our nation with the international research groups. Under the background, the author combined the thoughts of symplectic with wave equation pre-stack depth migration, and develops and efficient wave equation pre-stack depth migration method. The purpose of this work is to find out a way to imaging the complex geological goals of Chinese oilfields and form a procedure of seismic data processing. The paper gives the approximation of one way wave equation operator, and shows the numerical results. The comparisons have been made between split-step phase method, Kirchhoff and Ray+FD methods on the pulse response, simple model and Marmousi model. The result shows that the method in this paper has an higher accuracy. Four field data examples have also be given in this paper. The results of field data demonstrate that the method can be usable. The velocity estimation is an important part of the wave equation pre-stack depth migration. A. parallel velocity estimation program has been written and tested on the Beowulf clusters. The program can establish a velocity profile automatically. An example on Marmousi model has shown in the third part of the paper to demonstrate the method. Another field data was also given in the paper. Beowulf cluster is the converge of the high performance computer architecture. Today, Beowulf Cluster is a good choice for institutes and small companies to finish their task. The paper gives some comparison results the computation of the wave equation pre-stack migration on Beowulf cluster, IBM-SP2 (24 nodes) in Daqing and Shuguang3000, and the comparison of their prize. The results show that the Beowulf cluster is an efficient way to finish the large amount computation of the wave equation pre-stack depth migration, especially for 3D.

双聚焦偏移速度估计与可分表示叠前弹性反演

In exploration seismology, the geologic target of oil and gas reservoir in complex medium request the high accuracy image of the structure and lithology of the medium. So the study of the prestack image and the elastic inversion of seismic wave in the complex medium come to the leading edge. The seismic response measured at the surface carries two fundamental pieces of information: the propagation effects of the medium and the reflections from the different layer boundaries in the medium. The propagation represent the low-wavenumber component of the medium, it is so-called the trend or macro layering, whereas the reflections represent the high-wavenumber component of the medium, it is called the detailed or fine layering. The result of migration velocity analysis is the resolution of the low-wavenumber component of the medium, but the prestack elastic inversion provided the resolution of the high-wavvenumber component the medium. In the dissertation, the two aspects about the migration velocity estimation and the elastic inversion have been studied.Firstly, any migration velocity analysis methods must include two basic elements: the criterion that tell us how to know whether the model parameters are correct and the updating that tell us how to update the model parameters when they are incorrect, which are effected on the properties and efficiency of the velocity estimation method. In the dissertation, a migration velocity analysis method based on the CFP technology has been presented in which the strategy of the top-down layer stripping approach are adapted to avoid the difficult of the selecting reduce .The proposed method has a advantage that the travel time errors obtained from the DTS panel are defined directly in time which is the difference with the method based on common image gather in which the residual curvature measured in depth should be converted to travel time errors.In the proposed migration velocity analysis method, the four aspects have been improved as follow:? The new parameterization of velocity model is provided in which the boundaries of layers are interpolated with the cubic spline of the control location and the velocity with a layer may change along with lateral position but the value is calculated as a segmented linear function of the velocity of the lateral control points. The proposed parameterization is suitable to updating procedure.? The analytical formulas to represent the travel time errors and the model parameters updates in the t-p domain are derived under local lateral homogeneous. The velocity estimations are iteratively computed as parametric inversion. The zero differential time shift in the DTS panel for each layer show the convergence of the velocity estimation.? The method of building initial model using the priori information is provided to improve the efficiency of velocity analysis. In the proposed method, Picking interesting events in the stacked section to define the boundaries of the layers and the results of conventional velocity analysis are used to define the velocity value of the layers? An interactive integrate software environment with the migration velocity analysis and prestack migration is built.The proposed method is firstly used to the synthetic data. The results of velocity estimation show both properties and efficiency of the velocity estimation are very good.The proposed method is also used to the field data which is the marine data set. In this example, the prestack and poststack depth migration of the data are completed using the different velocity models built with different method. The comparison between them shows that the model from the proposed method is better and improves obviously the quality of migration.In terms of the theoretical method of expressing a multi-variable function by products of single-variable functions which is suggested by Song Jian (2001), the separable expression of one-way wave operator has been studied. A optimization approximation with separable expression of the one-way wave operator is presented which easily deal with the lateral change of velocity in space and wave number domain respectively and has good approach accuracy. A new prestack depth migration algorithm based on the optimization approximation separable expression is developed and used to testing the results of velocity estimation.Secondly, according to the theory of the seismic wave reflection and transmission, the change of the amplitude via the incident angle is related to the elasticity of medium in the subsurface two-side. In the conventional inversion with poststack datum, only the information of the reflection operator at the zero incident angles can be used. If the more robust resolutions are requested, the amplitudes of all incident angles should be used.A natural separable expression of the reflection/transmission operator is represented, which is the sum of the products of two group functions. One group function vary with phase space whereas other group function is related to elastic parameters of the medium and geological structure.By employing the natural separable expression of the reflection/transmission operator, the method of seismic wave modeling with the one-way wave equation is developed to model the primary reflected waves, it is adapt to a certain extent heterogeneous media and confirms the accuracy of AVA of the reflections when the incident angle is less than 45'. The computational efficiency of the scheme is greatly high.The natural separable expression of the reflection/transmission operator is also used to construct prestack elastic inversion algorithm. Being different from the AVO analysis and inversion in which the angle gathers formed during the prstack migration are used, the proposed algorithm construct a linear equations during the prestack migration by the separable expression of the reflection/transmission operator. The unknowns of the linear equations are related to the elasticity of the medium, so the resolutions of them provided the elastic information of the medium.The proposed method of inversion is the same as AVO inversion in , the difference between them is only the method processing the amplitude via the incident angle and computational domain.

Blind Characterisation of Sensors with Second-Order Dynamic Response

Compensation for the dynamic response of a temperature sensor usually involves the estimation of its input on the basis of the measured output and model parameters. In the case of temperature measurement, the sensor dynamic response is strongly dependent on the measurement environment and fluid velocity. Estimation of time-varying sensor model parameters therefore requires continuous textit{in situ} identification. This can be achieved by employing two sensors with different dynamic properties, and exploiting structural redundancy to deduce the sensor models from the resulting data streams. Most existing approaches to this problem assume first-order sensor dynamics. In practice, however second-order models are more reflective of the dynamics of real temperature sensors, particularly when they are encased in a protective sheath. As such, this paper presents a novel difference equation approach to solving the blind identification problem for sensors with second-order models. The approach is based on estimating an auxiliary ARX model whose parameters are related to the desired sensor model parameters through a set of coupled non-linear algebraic equations. The ARX model can be estimated using conventional system identification techniques and the non-linear equations can be solved analytically to yield estimates of the sensor models. Simulation results are presented to demonstrate the efficiency of the proposed approach under various input and parameter conditions.

Vector flow mapping using plane wave ultrasound imaging

Les diagnostics cliniques des maladies cardio-vasculaires sont principalement effectués à l’aide d’échographies Doppler-couleur malgré ses restrictions : mesures de vélocité dépendantes de l’angle ainsi qu’une fréquence d’images plus faible à cause de focalisation traditionnelle. Deux études, utilisant des approches différentes, adressent ces restrictions en utilisant l’imagerie à onde-plane, post-traitée avec des méthodes de délai et sommation et d’autocorrélation. L’objectif de la présente étude est de ré-implémenté ces méthodes pour analyser certains paramètres qui affecte la précision des estimations de la vélocité du flux sanguin en utilisant le Doppler vectoriel 2D. À l’aide d’expériences in vitro sur des flux paraboliques stationnaires effectuées avec un système Verasonics, l’impact de quatre paramètres sur la précision de la cartographie a été évalué : le nombre d’inclinaisons par orientation, la longueur d’ensemble pour les images à orientation unique, le nombre de cycles par pulsation, ainsi que l’angle de l’orientation pour différents flux. Les valeurs optimales sont de 7 inclinaisons par orientation, une orientation de ±15° avec 6 cycles par pulsation. La précision de la reconstruction est comparable à l’échographie Doppler conventionnelle, tout en ayant une fréquence d’image 10 à 20 fois supérieure, permettant une meilleure caractérisation des transitions rapides qui requiert une résolution temporelle élevée.