Effects of extraction methods on yam (Dioscorea alata) starch characteristics

Starch extraction from roots and tubers uses grating with water and sieves to separate the starch slurry from residual mass. The starch is recovered by decantation or centrifugation. The yam starch extraction is difficult due to high viscosity of the slurry caused by non-starch polysaccharides (NSP). The establishment of an efficient extraction process may turn yam into a competitive raw material. In this paper Dioscorea alata starch extracted by four methods was characterized in order to establish the impact of treatments. When the tubers were digested with an aqueous oxalic acid/ammonium oxalate (OA/AO) 1/1 solution, it was easier to separate the starch slurry from residual mass, because viscosity was reduced. For all the others methods tested, the viscosity remained almost the same. The nitrogen present in yam tubers was removed during the different extractions to a different extent. The largest nitrogen reduction was observed with ONAO followed by the control (water). The spectrum of starch granules sizes obtained also varied according to the treatment. Results proved that NSP carries small starch granules over to the waste water. The smaller starch granules diameter varied from 1.9 mu m (OA/AO extraction) to 13.5 mu m (water and pectinase extractions). The larger diameter varied from 41.0 mu m (NaOH treatment) to 67.7 mu m (ONAO). All starches extracted showed a RVA behavior in agreement with literature for yam starch, but with small differences due to the influence of methods. ONAO extraction showed the best recovery (18 g of starch/100 g tuber yam) and granular variation but it interfered with the rheological behavior of starch.

Planting time, developmental stages and characteristics of roots and starch of Pachyrhizus ahipa

De forma geral, as características do amido variam não somente com a planta de origem, mas também com o estádio de desenvolvimento desta. Neste trabalho objetivou-se avaliar a influência da época de plantio e estádio de desenvolvimento da planta de ahipa sobre as características físico-químicas das raízes, tamanho de grânulos do amido e suas propriedades viscográficas. Constatou-se influência do estádio de desenvolvimento da planta nas características físico-químicas das raízes e do amido, independentemente da época de plantio. A melhor época para o plantio de Pachyrhizus ahipa é outubro e a colheita deve ser feita no máximo com 9 meses, adotando-se o procedimento de retirada das flores a partir dos 3 meses.

Utilisation of local ingredients in commercial pig feeds

The long-term competitiveness of the both the Vietnamese feed and pig production industries are constrained and under pressure whilst the industry is dependent on the use of imported feed ingredients in diets for animal production. These cost pressures are a result of import taxes, transport costs, currency fluctuations and feed supply limitations. By undertaking studies on available resources which are currently under-utilised and with potential as local feeds, we can prove their suitability for use as feedstuffs in pig diets and as replacements for imported feed ingredients. In undertaking this process we can lower feeding costs for pig production in Vietnam by the use of local feeds which are cheaper, generate new industries in Vietnam harvesting or processing these feeds and increase the incomes of Vietnamese workers who are involved in producing these by-products. Our project has shown that rubber seed, when processed correctly to lower the hydrogen cyanide content, is a safe and suitable protein meal feedstuff for use in pig diets with the potential to replace significant quantities of imported soybean and fishmeal in Vietnamese pig diets as long as diets are balanced for any amino acid shortfalls. Our peanut studies have shown that use of binders can help alleviate pig production problems with aflatoxin content in peanut meals. Further work is needed to characterise the fate of the bound aflatoxin to see if there is any meat residue risk. Cassava residue is a resultant by-product from starch extraction in both large and small cassava processing factories. Sub-samples from these two mill types were collected and evaluated for residue HCN. Analyses has shown that the processing and sun drying results in a product with relatively consistent low HCN content. Chemical analyses also reveal that significant residual starch also remains in this by-product. Digestibility studies and pig performance feeding studies have shown that cassava residue can be included in diets at 30% with no adverse effect, although the higher fibre content of this product means that strategically, cassava residue is more suitably used in finisher and sow diets. Research has examined the digestible energy content of a number of sunflower meal types available in Australia and identified major differences in their energy value based on processing, additionally, amino acid analysis has shown a significantly lower lysine content than previous reported. We also examined the digestible energy content of a number of Australian stylo forage legume harvest batches and identified the differences in their energy value based on age/harvest time of the forage legume. Analysis results of various stylo cuts showed that the early cut stylo has a higher starch content and lower fibre fraction content than observed in late and recut stylo which were allowed to grow longer. As a result the faecal digestible energy content was higher for the early cut stylo than for the subsequent cut stylo material which had been allowed to become woody. The results have shown that feeding of stylo meal does provide some nutritive value to the pig with increased energy and nitrogen supply, with a portion of the nitrogen presented which the pig is able to retain. Based on nutrient and fibre content stylo could have a useful role in sow feeding and satiety under non-stall housing situations. With increasing Vietnamese investment in rubber production seen with larger areas under plantations the amounts of rubber seed available for animal feeding will grow significantly over the next 15 years and the importance of the by-product ie rubber seed meal as a protein source in diets for Vietnamese pigs.

Extração da fécula retida no resíduo fibroso do processo de produção de fécula de mandioca

A melhoria do processo de extração da fécula de mandioca é um problema bastante discutido entre industriais e pesquisadores. Atualmente, para cada tonelada de raiz de mandioca processada obtêm-se por volta de 250kg de fécula e perde-se no resíduo fibroso cerca de 140kg de fécula que não foi extraída no processamento. Neste trabalho objetivou-se analisar o efeito de uma segunda extração em paralelo e o uso de soluções auxiliares na extração da fécula retida no resíduo fibroso (farelo), visando a melhoria no rendimento industrial. Foram avaliados quatro tratamentos utilizando-se: água (T1), solução de NaOH 0,2% (T2), solução água-álcool 10%v/v (T3) e solução água- Tween 80 0,002% (T4). A partir dos resultados obtidos foi possível concluir que a adição de soluções auxiliares não promoveu diferença significativa (p< 0,05) de extração em relação à água (T1), e que uma nova extração da fécula retida no farelo possibilitaria uma redução de cerca de 20% no teor de amido do farelo, o qual não é extraído no processo convencional.

Extração e caracterização de amido de jacatupé (Pachyrhizus ahipa)

O gênero Pachyrhizus tem sido estudado como fonte de matéria-prima amilácea devido ao considerável teor de amido nas raízes de suas espécies. Neste trabalho objetivou-se caracterizar raízes de P. ahipa, processar em laboratório para a extração do amido e analisá-lo quanto à composição centesimal, teor de amilose, formato e tamanho de grânulos em microscópio eletrônico de varredura e viscosidade das pastas (RVA). As raízes de P. ahipa apresentaram 18% de massa seca sendo 7,68% amido. O rendimento obtido de amido foi baixo (4,28%), apontando para a necessidade de estudos que melhorem o processo de extração. O produto obtido apresentou 12,3% de umidade, 84% de amido com 13% de amilose e baixos teores de outros componentes (base úmida). A análise em microscópio eletrônico de varredura mostrou grânulos de amido de formas circular e poligonal, com tamanho variando entre 10 e 25mm. O perfil de viscosidade apresentado por este amido mostrou baixa temperatura de pasta (56ºC) e pico de viscosidade a 272 RVU, estando este último valor próximo ao observado para amido de mandioca, sob as mesmas condições. O amido de P. ahipa apresentou ainda, baixa estabilidade da pasta a quente e tendência à retrogradação com o resfriamento.

Produção e qualidade de raiz tuberosa de cultivares de batata-doce no Oeste do Paraná

The objective of this work was to evaluate sweet potato cultivars with starch processing capability, on two cultivation periods, in the western region of Parana (Brazil). Sweet potato was grown at Marechal Candido Rondon, Parana State (24 degrees 33'40 '' S and 54 degrees 4'12 '' W), at a mean annual temperature between 14 and 28 degrees C. The experiment was designed in complete randomized blocks, in a factorial scheme of 4 cultivars (CNPH 003, CNPH 004, Brazlandia Roxa, and Brazlandia Rosada) and 2 cultivation periods (115 and 183 days), with four repetitions. The evaluated parameters were the root productivities (t ha(-1)) and the physical and chemical root composition (humidity, pH, acidity, starch, total soluble sugars and fibers). Data was submitted to all analysis of variance (Anova) and the means were compared by the Tukey test at 5% of probability, Results indicated that sweet potato yield at the cultivars was higher during the 183 day cultivation period (average of 9.14 t ha(-1)) than during the 115 day cultivation period (average of 4.25 t ha(-1)). Thus the CNPH 003 cultivar seems to be a better indication for starch extraction, due to the lowest fiber content in the root, the driest mass content and the largest yield of starch per area.

Caracterização da farinha e do amido isolado da semente de jaca e comportamento reológico de dispersões de amido

O amido é um ingrediente com grande versatilidade de aplicação, e as sementes de jaca, fruto bem difundido, porém pouco aproveitado no Brasil, contêm uma quantidade considerável de amido, sendo ainda fonte de ferro e proteínas. Dessa maneira, os objetivos desse projeto foram a obtenção da farinha de sementes de jaca das variedades mole e dura, a extração do amido utilizando diferentes solventes, e a caracterização de suas propriedades físico-químicas, estruturais e funcionais, bem como a caracterização reológica de dispersões/géis de amido em cisalhamento estacionário e oscilatório. A extração alcalina do amido, além de reduzir significativamente o conteúdo de lipídeos e proteínas, deixando o amido mais puro, promoveu um aumento no teor de amilose e influenciou diretamente as características de inchamento e solubilidade, que apresentaram aumento significativo a partir da temperatura de 70 °C. O aumento da temperatura ocasionou aumento no poder de inchamento e solubilidade, que foi mais pronunciado para a variedade dura, porém esses valores ainda foram considerados baixos (< 17%). Os amidos de sementes de jaca apresentaram grânulos lisos, arredondados e em forma de sino, com formato mais truncado para o amido extraído com hidróxido de sódio. O diâmetro médio dos grânulos de amido foi menor para a extração alcalina, mas sempre com comportamento monomodal. Foi observado um padrão de difração de Raios-X do tipo A para todas as amostras estudadas, e o índice de cristalinidade foi maior para os amidos de sementes de jaca dura, com uma redução estimada em 70% para os amidos obtidos por extração alcalina. A temperatura de gelatinização dos amidos de semente de jaca foi considerada alta (70-100 °C). Os amidos de sementes de jaca dura obtidos na extração com água apresentaram maiores valores de viscosidade de pico e de Breakdown, que representa menor resistência mecânica. A extração com solução de NaOH 0,1 M aumentou a tendência a retrogradação de ~36% (extração aquosa) para 64% e 45% dos amidos de sementes de jaca das variedades mole e dura, respectivamente. Todas as amostras apresentaram comportamento pseudoplástico (n < 1) nas concentrações e temperaturas estudadas, e as dispersões e/ou géis de amido obtidos pela extração alcalina com NaOH apresentaram menor tixotropia e maiores valores de viscosidade. Os modelos Lei da Potência e Herschel Bulkley apresentaram ótimos ajustes aos pontos experimentais (R² ~0,998) para as amostras com 2 e 6 % de amido, respectivamente, porém para a concentração de 5%, o melhor modelo foi função da variedade do fruto usado na obtenção do amido. A dependência das propriedades reológicas com a temperatura foi analisada pela equação de Arrhenius e a energia de ativação foi baixa (15-25 kJ/mol). Quanto ao comportamento viscoelástico, as amostras com 5 e 6% de amido apresentaram comportamento de gel fraco e o aumento da concentração desse polissacarídeo produziu um aumento na elasticidade do material. Os módulos de armazenamento (G\') associados à elasticidade do gel de amido aumentaram durante o seu resfriamento nos ensaios de varredura de temperatura, o que pode ser relacionado à recristalização da amilose durante esse processo e mantiveram-se praticamente constantes no aquecimento isotérmico a 80 °C, sugerindo boa estabilidade térmica do gel. A farinha isolada da semente de jaca pode ser considerada fonte de fibras e apresentou elevados teores de proteínas (~14-16%) e ferro (~85-150 mg/kg). A distribuição do tamanho de partículas da farinha apresentou comportamento bimodal, com grânulos arredondados, presença de fibras e uma matriz proteica envolvendo os grânulos de amido. As propriedades de pasta revelaram maior pico de viscosidade para a farinha de semente de jaca mole. As características encontradas sugerem que os amidos de semente de jaca poderiam ser aplicados na produção de filmes biodegradáveis, e a farinha da semente de jaca poderia ser utilizada em substituição parcial à farinha convencional na fabricação de bolos e biscoitos.

Glycoalkaloid Content and Starch Structure in Solanum Species and Interspecific Somatic Potato Hybrids

When genome sections of wild Solanum species are bred into the cultivated potato (S. tuberosum L.) to obtain improved potato cultivars, the new cultivars must be evaluated for their beneficial and undesirable traits. Glycoalkaloids present in Solanum species are known for their toxic as well as for beneficial effects on mammals. On the other hand, glycoalkaloids in potato leaves provide natural protection against pests. Due to breeding, glycoalkaloid profile of the plant is affected. In addition, the starch properties in potato tubers can be affected as a result of breeding, because the crystalline properties are determined by the botanical source of the starch. Starch content and composition affect the texture of cooked and processed potatoes. In order to determine glycoalkaloid contents in Solanum species, simultaneous separation of glycoalkaloids and aglycones using reversed-phase high-performance liquid chromatography (HPLC) was developed. Clean-up of foliage samples was improved using a silica-based strong cation exchanger instead of octadecyl phases in solid-phase extraction. Glycoalkaloids alpha-solanine and alpha-chaconine were detected in potato tubers of cvs. Satu and Sini. The total glycoalkaloid concentration of non-peeled and immature tubers was at an acceptable level (under 20 mg/100 g of FW) in the cv. Satu, whereas concentration in cv. Sini was 23 mg/100 g FW. Solanum species (S. tuberosum, S. brevidens, S. acaule, and S. commersonii) and interspecific somatic hybrids (brd + tbr, acl + tbr, cmm + tbr) were analyzed for their glycoalkaloid contents using liquid chromatography-electrospray ionization-mass spectrometry (LC-ESI-MS). The concentrations in the tubers of the brd + tbr and acl + tbr hybrids remained under 20 mg/100 g FW. Glycoalkaloid concentration in the foliage of the Solanum species was between 110 mg and 890 mg/100 g FW. However, the concentration in the foliage of S. acaule was as low as 26 mg/100 g FW. The total concentrations of brd + tbr, acl + tbr, and cmm + tbr hybrid foliages were 88 mg, 180 mg, and 685 mg/100 g FW, respectively. Glycoalkaloids of both parental plants as well as new combinations of aglycones and saccharides were detected in somatic hybrids. The hybrids contained mainly spirosolanes, and glycoalkaloid structures having no 5,6-double bond in the aglycone. Based on these results, the glycoalkaloid profiles of the hybrids may represent a safer and more beneficial spectrum of glycoalkaloids than that found in currently cultivated varieties. Starch nanostructure of three different cultivars (Satu, Saturna, and Lady Rosetta), a wild species S. acaule, and interspecific somatic hybrids were examined by wide-angle and small-angle X-ray scattering (WAXS, SAXS). For the first time, the measurements were conducted on fresh potato tuber samples. Crystallinity of starch, average crystallite size, and lamellar distance were determined from the X-ray patterns. No differences in the starch nanostructure between the three different cultivars were detected. However, tuber immaturity was detected by X-ray scattering methods when large numbers of immature and mature samples were measured and the results were compared. The present study shows that no significant changes occurred in the nanostructures of starches resulting from hybridizations of potato cultivars.

Edible oil from Tiger nut (Cyperus esculentus L.): mechanical pressing and aqueous enzymatic extraction methods

The tiger nut tuber of the Cyperus esculentus L. plant is an unusual storage system with similar amounts of starch and lipid. The extraction of its oil employing both mechanical pressing and aqueous enzymatic extraction (AEE) methods was investigated and an examination of the resulting products was carried out. The effects of particle size and moisture content of the tuber on the yield of tiger nut oil with pressing were initially studied. Smaller particles were found to enhance oil yields while a range of moisture content was observed to favour higher oil yields. When samples were first subjected to high pressures up to 700 MPa before pressing at 38 MPa there was no increase in the oil yields. Ground samples incubated with a mixture of α- Amylase, Alcalase, and Viscozyme (a mixture of cell wall degrading enzyme) as a pre-treatment, increased oil yield by pressing and 90% of oil was recovered as a result. When aqueous enzymatic extraction was carried out on ground samples, the use of α- Amylase, Alcalase, and Celluclast independently improved extraction oil yields compared to oil extraction without enzymes by 34.5, 23.4 and 14.7% respectively. A mixture of the three enzymes further augmented the oil yield and different operational factors were individually studied for their effects on the process. These include time, total mixed enzyme concentration, linear agitation speed, and solid-liquid ratio. The largest oil yields were obtained with a solid-liquid ratio of 1:6, mixed enzyme concentration of 1% (w/w) and 6 h incubation time although the longer time allowed for the formation of an emulsion. Using stationary samples during incubation surprisingly gave the highest oil yields, and this was observed to be as a result of gravity separation occurring during agitation. Furthermore, the use of high pressure processing up to 300 MPa as a pre-treatment enhanced oil yields but additional pressure increments had a detrimental effect. The quality of oils recovered from both mechanical and aqueous enzymatic extraction based on the percentage free fatty acid (% FFA) and peroxide values (PV) all reflected the good stabilities of the oils with the highest % FFA of 1.8 and PV of 1.7. The fatty acid profiles of all oils also remained unchanged. The level of tocopherols in oils were enhanced with both enzyme aided pressing (EAP) and high pressure processing before AEE. Analysis on the residual meals revealed DP 3 and DP 4 oligosaccharides present in EAP samples but these would require further assessment on their identity and quality.

Extraction of cellulose whiskers from cassava bagasse and their applications as reinforcing agent in natural rubber

In this work cassava bagasse, a by-product of cassava starch industrialization was investigated as a new raw material to extract cellulose whiskers. This by-product is basically constituted of cellulose fibers (17.5 wt%) and residual starch (82 wt%). Therefore, this residue contains both natural fibers and a considerable quantity of starch and this composition suggests the possibility of using cassava bagasse to prepare both starch nanocrystals and cellulose whiskers. In this way, the preparation of cellulose whiskers was investigated employing conditions of sulfuric acid hydrolysis treatment found in the literature. The ensuing materials were characterized by transmission electron microscopy (TEM) and X-ray diffraction experiments. The results showed that high aspect ratio cellulose whiskers were successfully obtained. The reinforcing capability of cellulose whiskers extracted from cassava bagasse was investigated using natural rubber as matrix. High mechanical properties were observed from dynamic mechanical analysis. (C) 2010 Elsevier B.V. All rights reserved.

Cassava bagasse cellulose nanofibrils reinforced thermoplastic cassava starch

Cellulose cassava bagasse nanofibrils (CBN) were directly extracted from a by-product of the cassava starch (CS) industry, viz. the cassava bagasse (CB), The morphological structure of the ensuing nanoparticles was investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM), presence of other components such as sugars by high performance liquid chromatography (HPLC), thermogravimetric analysis (TGA), and X-ray diffraction (XRD) experiments. The resulting nanofibrils display a relatively low crystallinity and were found to be around 2-11 nm thick and 360-1700 nm long. These nanofibrils were used as reinforcing nanoparticles in a thermoplastic cassava starch matrix plasticized using either glycerol or a mixture of glycerol/sorbitol (1:1) as plasticizer. Nanocomposite films were prepared by a melting process. The reinforcing effect of the filler evaluated by dynamical mechanical tests (DMA) and tensile tests was found to depend on the nature of the plasticizer employed. Thus, for the glycerol-plasticized matrix-based composites, it was limited especially due to additional plasticization by sugars originating from starch hydrolysis during the acid extraction. This effect was evidenced by the reduction of glass vitreous temperature of starch after the incorporation of nanofibrils in TPSG and by the increase of elongation at break in tensile test. On the other hand, for glycerol/sorbitol plasticized nanocomposites the transcrystallization of amylopectin in nanofibrils surface hindered good performances of CBN as reinforcing agent for thermoplastic cassava starch. The incorporation of cassava bagasse cellulose nanofibrils in the thermoplastic starch matrices has resulted in a decrease of its hydrophilic character especially for glycerol plasticized sample. (C) 2009 Elsevier Ltd. All rights reserved.

The Effects of 6% Hydroxyethyl Starch-Hypertonic Saline in Resuscitation of Dogs with Hemorrhagic Shock

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Three classes of starch granule swelling: Influence of surface proteins and lipids

The role of non-carbohydrate surface components of granular starch in determining gelatinisation behaviour has been tested by treatment of native starches with a range of extractants. Resulting washed starches were analysed for (bio)chemical, calorimetric and theological properties. Sodium dodecyl sulphate (SDS) was the most efficient extractant tested, and resulted in major changes to the subsequent theological properties of wheat and maize starches but not other starches. Three classes of starch granule swelling behaviour are identified: (i) rapid swelling (e.g. waxy maize, potato), (ii) slow swelling that can be converted to rapid swelling by extraction of surface proteins and lipids (e.g. wheat, maize), and (iii) limited swelling not affected by protein/lipid extraction (e.g. high amylose maize/potato). Comparison of a range of extractants suggests that all of protein, lipid and amylose are involved in restriction of swelling for wheat or maize starches. Treatment of starches with SDS leads to a residue at comparable (low) levels of SDS for all starches. C-13 NMR analysis shows that this SDS is present as a glucan inclusion complex, even for waxy maize starch. We infer that under the conditions used, glucan inclusion complexation of SDS is equally likely with amylopectin as with amylose. (c) 2006 Elsevier Ltd. All rights reserved.