The behaviour of granular material in pure shear, direct shear and simple shear

In biaxial compression tests, the stress calculations based on boundary information underestimate the principal stresses leading to a significant overestimation of the shear strength. In direct shear tests, the shear strain becomes highly concentrated in the mid-plane of the sample during the test. Although the stress distribution within the specimen is heterogeneous, the evolution of the stress ratio inside the shear band is similar to that inferred from the boundary force calculations. It is also demonstrated that the dilatancy in the shear band significantly exceeds that implied from the boundary displacements. In simple shear tests, the stresses acting on the wall boundaries do not reflect the internal state of stress but merely provide information about the average mobilised wall friction. It is demonstrated that the results are sensitive to the initial stress state defined by K0 = sh/sv. For all cases, non-coaxiality of the principal stress and strain-rate directions is examined and the corresponding flow rule is identified. Periodic cell simulations have been used to examine biaxial compression for a wide range of initial packing densities. Both constant volume and constant mean stress tests have been simulated. The characteristic behaviour at both the macroscopic and microscopic scales is determined by whether or not the system percolates (enduring connectivity is established in all directions). The transition from non-percolating to percolating systems is characterised by transitional behaviour of internal variables and corresponds to an elastic percolation threshold, which correlates well with the establishment of a mechanical coordination number of ca. 3.0. Strong correlations are found between macroscopic and internal variables at the critical state.

Crack-growth of medical-grade silicone using pure shear tests

Silicone elastomers are commonly used in the manufacture of single-piece joint replacement implants for the finger joints. However, the survivorship of these implants can be poor, with failure typically occurring from fracture of the stems. The aim of this paper was to investigate the crack growth of medical-grade silicone using pure shear tests. Two medical-grade silicones (C6-180 and Med82-5010-80) were tested. Each sample had a 20 mm crack introduced and was subjected to a sinusoidally varying tensile strain, with a minimum of 0 per cent and a maximum in the range 10 to 77 per cent. Testing was undertaken at a frequency of 10 Hz. At various times during testing, the testing machine was stopped, the number of cycles completed was noted, and the crack length measured. Graphs of crack length against number of cycles were plotted, as well as the crack growth rate against tearing energy. The results show that Med82-5010-80 is more crack resistant than C6-180. Graphs of crack growth rate against tearing energy can be used to predict the failure of these medical-grade elastomers.

Bending fatigue of stainless steel shear pins belonging to a hydroelectric plant

Coaracy Nunes was the first hydroelectric power plant in the Amazon region, being located in Araguari River, Amapa State, Brazil. The plant operates since 1976, presenting now a nominal capacity of 78 MW. The shear pins, which are installed in the turbine hydraulic arms to control the wicket gate and regulate the water flow into the turbine blades, suffered several breakdowns since 2004. These shear pins are made of an ASTM 410 stainless steel and were designed to break by a shear overload of 120 kN. Fractographic investigation of the pins, however, revealed two types of fracture topographies: a region of stable crack propagation area, with non-pronounced striation and secondary cracks; and a region of unstable propagation, featuring elongated dimples. These results indicated that the stable crack propagation occurred by fatigue (bidirectional bending), which was nucleated at machining marks under high nominal load. Finite element analysis was carried out using two loading conditions (pure shear and a combination of shear and bending) and the results indicated that the presence of a bending stress strongly increased the stress concentration factor (85% rise in the shear stress and 130% rise in the Von Mises stress). Misalignment during shear pins assembly associated with vibration might have promoted the premature failure of the shear by bending fatigue. (C) 2008 Elsevier Ltd. All rights reserved.

Desenvolvimento de ferramentas e provetes para o ensaio Thick Adherend Shear Test (TAST).

As estruturas coladas são geralmente projetadas para que o adesivo seja essencialmente sujeito a esforços de corte, pois neste tipo de solicitação o adesivo apresenta melhores caraterísticas mecânicas. A avaliação do comportamento ao corte pode ser realizada com o adesivo no estado maciço ou como camada fina em juntas adesivas. Os métodos que permitem avaliar o comportamento ao corte, quer para o adesivo, quer para as juntas, são: o ensaio Iosipescu ou V-Notched beam shear method, o ensaio de borboleta ou Notched plate shear method (Arcan), o ensaio de torsão, o ensaio de tração numa junta de sobreposição simples e o ensaio Thick Adherend Shear Test (TAST). Os ensaios Arcan e Iosipescu, tal como o ensaio de torção, podem ser realizados em provetes de adesivo maciço ou em juntas. O ensaio de torção é pouco utilizado, porque a aplicação do esforço de corte exige dispositivos e equipamentos de ensaios complexos. Os ensaios Arcan e Iosipescu utilizam provetes com entalhes e podem introduzir alguma dificuldade na medição precisa das deformações. O ensaio de tração numa junta de sobreposição simples é um dos métodos mais usados para caraterizar uma junta adesiva, porque é um método simples, as juntas são de fácil fabrico e pode ser realizado em máquinas universais de ensaios mecânicos. Neste ensaio os aderentes estão sujeitos a uma solicitação de tração, enquanto a camada de adesivo está sujeita a esforços de corte combinados com esforços de arrancamento. Os esforços de arrancamento resultam da própria geometria da junta na qual existe um desalinhamento das forças de tração, mesmo quando são colocados calços (reguladores de espessura) nos locais de amarração. O ensaio TAST é dos mais populares para obtenção das propriedades ao corte, uma vez que tanto as ferramentas de ensaio como o fabrico dos provetes são relativamente simples. Este ensaio é realizado em junta sendo os substratos espessos e de aço que, devido à sua elevada rigidez, contribuem para um esforço de corte praticamente puro no adesivo. Neste trabalho realizou-se o projeto e a fabricação das ferramentas, gabarit e substratos necessários para a execução de provetes TAST e ensaios utilizando diferentes adesivos.

Preservation of an extreme transient geotherm in the Raft River detachment shear zone

Extensional detachment systems separate hot footwalls from cool hanging walls, but the degree to which this thermal gradient is the product of ductile or brittle deformation or a preserved original transient geotherm is unclear. Oxygen isotope thermometry using recrystallized quartz-muscovite pairs indicates a smooth thermal gradient (140 degrees C/100 m) across the gently dipping, quartzite-dominated detachment zone that bounds the Raft River core complex in northwest Utah (United States). Hydrogen isotope values of muscovite (delta D-Ms similar to-100 parts per thousand) and fluid inclusions in quartz (delta D-Fluid similar to-85 parts per thousand) indicate the presence of meteoric fluids during detachment dynamics. Recrystallized grain-shape fabrics and quartz c-axis fabric patterns reveal a large component of coaxial strain (pure shear), consistent with thinning of the detachment section. Therefore, the high thermal gradient preserved in the Raft River detachment reflects the transient geotherm that developed owing to shearing, thinning, and the potentially prominent role of convective flow of surface fluids.

The Sottunga-Jurmo shear zone : structure and deformation history of a crustal-scale ductile shear zone in SW Finland

The aim of this study is to gain a better understanding of the structure and the deformation history of a NW-SE trending regional, crustal-scale shear structure in the Åland archipelago, SW Finland, called the Sottunga-Jurmo shear zone (SJSZ). Approaches involving e.g. structural geology, geochronology, geochemistry and metamorphic petrology were utilised in order to reconstruct the overall deformation history of the study area. The study therefore describes several features of the shear zone including structures, kinematics and lithologies within the study area, the ages of the different deformation phases (ductile to brittle) within the shear zone, as well as some geothermobarometric results. The results indicate that the SJSZ outlines a major crustal discontinuity between the extensively migmatized rocks NE of the shear zone and the unmigmatised, amphibolite facies rocks SW of the zone. The main SJSZ shows overall dextral lateral kinematics with a SW-side up vertical component and deformation partitioning into pure shear and simple shear dominated deformation styles that was intensified toward later stages of the deformation history. The deformation partitioning resulted in complex folding and refolding against the SW margin of the SJSZ, including conical and sheath folds, and in a formation of several minor strike-slip shear zones both parallel and conjugate to the main SJSZ in order to accommodate the regional transpressive stresses. Different deformation phases within the study area were dated by SIMS (zircon U-Pb), ID-TIMS (titanite U-Pb) and 40Ar/39Ar (pseudotachylyte wholerock) methods. The first deformation phase within the ca. 1.88 Ga rocks of the study area is dated at ca. 1.85 Ga, and the shear zone was reactivated twice within the ductile regime (at ca. 1.83 Ga and 1.79 Ga), during which the strain was successively increasingly partitioned into the main SJSZ and the minor shear zones. The age determinations suggest that the orogenic processes within the study area did not occur in a temporal continuum; instead, the metamorphic zircon rims and titanites show distinct, 10-20 Ma long breaks in deformation between phases of active deformation. The results of this study further imply slow cooling of the rocks through 600-700ºC so that at 1.79 Ga, 2 the temperature was still at least 600ºC. The highest recorded metamorphic pressures are 6.4-7.1 kbar. At the late stages or soon after the last ductile phase (ca. 1.79 Ga), relatively high-T mylonites and ultramylonites were formed, witnessing extreme deformation partitioning and high strain rates. After the rocks reached lower amphibolite facies to amphibolite-greenschist facies transitional conditions (ca. 500-550ºC), they cooled rapidly, probably due to crustal uplift and exhumation. The shear zone was reactivated at least once within the semi-brittle to brittle regime between ca. 1.79 Ga and 1.58 Ga, as evidenced by cataclasites and pseudotachylytes. In summary, the results of this study suggest that the Sottunga-Jurmo shear zone (and the South Finland shear zone) defines a major crustal discontinuity, and played a central role in accommodating the regional stresses during and after the Svecofennian orogeny.

The Sottunga-Jurmo shear zone : structure and deformation history of a crustal-scale ductile shear zone in SW Finland

The aim of this study is to gain a better understanding of the structure and the deformation history of a NW-SE trending regional, crustal-scale shear structure in the Åland archipelago, SW Finland, called the Sottunga-Jurmo shear zone (SJSZ). Approaches involving e.g. structural geology, geochronology, geochemistry and metamorphic petrology were utilised in order to reconstruct the overall deformation history of the study area. The study therefore describes several features of the shear zone including structures, kinematics and lithologies within the study area, the ages of the different deformation phases (ductile to brittle) within the shear zone, as well as some geothermobarometric results. The results indicate that the SJSZ outlines a major crustal discontinuity between the extensively migmatized rocks NE of the shear zone and the unmigmatised, amphibolite facies rocks SW of the zone. The main SJSZ shows overall dextral lateral kinematics with a SW-side up vertical component and deformation partitioning into pure shear and simple shear dominated deformation styles that was intensified toward later stages of the deformation history. The deformation partitioning resulted in complex folding and refolding against the SW margin of the SJSZ, including conical and sheath folds, and in a formation of several minor strike-slip shear zones both parallel and conjugate to the main SJSZ in order to accommodate the regional transpressive stresses. Different deformation phases within the study area were dated by SIMS (zircon U-Pb), ID-TIMS (titanite U-Pb) and 40Ar/39Ar (pseudotachylyte wholerock) methods. The first deformation phase within the ca. 1.88 Ga rocks of the study area is dated at ca. 1.85 Ga, and the shear zone was reactivated twice within the ductile regime (at ca. 1.83 Ga and 1.79 Ga), during which the strain was successively increasingly partitioned into the main SJSZ and the minor shear zones. The age determinations suggest that the orogenic processes within the study area did not occur in a temporal continuum; instead, the metamorphic zircon rims and titanites show distinct, 10-20 Ma long breaks in deformation between phases of active deformation. The results of this study further imply slow cooling of the rocks through 600-700ºC so that at 1.79 Ga, 2 the temperature was still at least 600ºC. The highest recorded metamorphic pressures are 6.4-7.1 kbar. At the late stages or soon after the last ductile phase (ca. 1.79 Ga), relatively high-T mylonites and ultramylonites were formed, witnessing extreme deformation partitioning and high strain rates. After the rocks reached lower amphibolite facies to amphibolite-greenschist facies transitional conditions (ca. 500-550ºC), they cooled rapidly, probably due to crustal uplift and exhumation. The shear zone was reactivated at least once within the semi-brittle to brittle regime between ca. 1.79 Ga and 1.58 Ga, as evidenced by cataclasites and pseudotachylytes. In summary, the results of this study suggest that the Sottunga-Jurmo shear zone (and the South Finland shear zone) defines a major crustal discontinuity, and played a central role in accommodating the regional stresses during and after the Svecofennian orogeny.

Deformation and geochronology of syntectonic granitoids emplaced in the Major Gercino Shear Zone, southeastern South America

The Major Gercino Shear Zone is one of the NE-SW lineaments that separate the Neoproterozoic Dom Feliciano Belt, of Brazil and Uruguay, into two different domains: a northwestern supracrustal domain from a southeastern granitoid domain. The shear zone, striking NE, is composed of protomylonites to ultramylonites with mainly dextral kinematic indicators. In Santa Catarina State, southern Brazil, the shear zone is composed of two mylonite belts. The mylonites have mineral orientations produced under greenschist fades conditions at a high strain rate. Strong flattening and coaxial deformation indicate the transpressive character, while the role of pure shear is emphasized by the orientation of the mylonite belts in relation to the inferred stress field component. The quartz microstructures point out that different dynamic recrystallization regimes and crystal plasticity were the dominant mechanisms of deformation during the mylonitization process. Additionally, the fabrics suggest that the glide systems are activated for deformation conditions compatible with the metamorphism in the middle greenschist facies. Elongated granitoid intrusions belonging to two petrographically, geochemically and isotopically distinct rock associations occur between the two mylonite belts. The structures observed in the granites result from a deformation range from magmatic to solid-state conditions points to a continuum of magma straining during and just after its crystallization. Conventional U-Pb analysis of multi-crystal zircon fractions yielded essentially identical ages of 609 +/- 16 Ma and 614 +/- 2 Ma for the two granitic associations, and constrain the transpressive phase of the shear zone. K-Ar ages of biotites between 585 and 560 Ma record the slow cooling and uplift of the intrusions. Some K-Ar ages of micas in regional mylonites are similar, suggesting that thermo-tectonic activity was intense up to this time, probably related to the agglutination of the granite belt to the supracrustal belt NW of the MGSZ. (C) 2009 International Association for Gondwana Research. Published by Elsevier B.V. All rights reserved.

The tectonically controlled emplacement of a vertically sheeted gabbro-pyroxenite intrusion: Feeder-zone of an ocean-island volcano (Fuerteventura, Canary Islands)

The Miocene PX1 gabbro-pyroxenite pluton, Fuerteventura, Canary Islands, is a 3.5 x 5.5 km shallow-level intrusion (0.15-0.2 GPa and 1100-1120 degrees C), interpreted as the feeder-zone to an ocean-island volcano. It displays a vertical magmatic banding expressed in five 50 to 100 metre-wide NNE-SSW trending alkaline gabbro sequences alternating with pyroxenites. This emplacement geometry was controlled by brittle to ductile shear zones, generated by a regional E-W extensional tectonic setting that affected Fuerteventura during the Miocene. At a smaller scale, the PX1 gabbro and pyroxenite bands consist of metre-thick differentiation units, which suggest emplacement by periodic injection of magma pulses as vertical dykes that amalgamated, similarly to a sub-volcanic sheeted dyke complex. Individual dykes underwent internal differentiation following a solidification front parallel to the dyke edges. This solidification front may have been favoured by a significant lateral/horizontal thermal gradient, expressed by the vertical banding in the gabbros, the fractionation asymmetry within individual dykes and the migmatisation of the wall rocks. Pyroxenitic layers result from the fractionation and accumulation of clinopyroxene +/- olivine +/- plagioclase crystals from a mildly alkaline basaltic liquid. They are interpreted as truncated differentiation sequences, from which residual melts were extracted at various stages of their chemical evolution by subsequent dyke intrusions, either next to or within the crystallising unit. Compaction and squeezing of the crystal mush is ascribed to the incoming and inflating magma pulses. The expelled interstitial liquid was likely collected and erupted along with the magma flowing through the newly injected dykes. Clinopyroxene mineral orientation - as evidenced by EBSD and micro X-ray tomography investigations - displays a marked pure-shear component, supporting the interpretation of the role of compaction in the generation of the pyroxenites. Conversely, gabbro sequences underwent minor melt extraction and are believed to represent crystallised coalesced magma batches emplaced at lower rates at the end of eruptive cycles. Clinopyroxene orientations in gabbros record a simple shear component suggesting syn-magmatic deformation parallel to observed NNE-SSW trending shear zones induced by the regional tensional stress field. This emplacement model implies a crystallisation time of 1 to 5 years for individual dykes, consistent with PX1 emplacement over less than 0.5 My. A minimum amount of approximately 150 km(3) of magma is needed to generate the pluton, part of it having been erupted through the Central Volcanic Centre of Fuerteventura. If the regional extensional tectonic regime controls the PX1 feeder-zone initiation and overall geometry, rates and volumes of magma depend on other, source-related factors. High injection rates are likely to induce intrusion growth rates larger than could be accommodated by the regional extension. In this case, dyke intrusion by propagation of a weak tip, combined with the inability of magma to circulate through previously emplaced and crystallised dykes could result in an increase of non-lithostatic pressure on previously emplaced mushy dyke walls; thus generating strong pure-shear compaction within the pluton feeder-zone and interstitial melt expulsion. These compaction-dominated processes are recorded by the cumulitic pyroxenite bands. (C) 2010 Elsevier B.V. All rights reserved.

Design and Evaluation of a Single-Span Bridge Using Ultra- High Performance Concrete, September 2009

Research presented herein describes an application of a newly developed material called Ultra-High Performance Concrete (UHPC) to a single-span bridge. The two primary objectives of this research were to develop a shear design procedure for possible code adoption and to provide a performance evaluation to ensure the viability of the first UHPC bridge in the United States. Two other secondary objectives included defining of material properties and understanding of flexural behavior of a UHPC bridge girder. In order to obtain information in these areas, several tests were carried out including material testing, large-scale laboratory flexure testing, large-scale laboratory shear testing, large-scale laboratory flexure-shear testing, small-scale laboratory shear testing, and field testing of a UHPC bridge. Experimental and analytical results of the described tests are presented. Analytical models to understand the flexure and shear behavior of UHPC members were developed using iterative computer based procedures. Previous research is referenced explaining a simplified flexural design procedure and a simplified pure shear design procedure. This work describes a shear design procedure based on the Modified Compression Field Theory (MCFT) which can be used in the design of UHPC members. Conclusions are provided regarding the viability of the UHPC bridge and recommendations are made for future research.

From rifting to passive margin - The examples of the Red Sea, Central Atlantic and Alpine Tethys

Evolution of the Red Sea/Gulf of Suez and the Central Atlantic rift systems shows that an initial, transtensive rifting phase, affecting a broad area around the future zone of crustal separation, was followed by a pre-oceanic rifting phase during which extensional strain was concentrated on the axial rift zone. This caused lateral graben systems to become inactive and they evolved into rift-rim basins. The transtensive phase of diffuse crustal extension is recognized in many intra-continental rifts. If controlling stress systems relax, these rifts abort and develop into palaeorifts. If controlling stress systems persist, transtensive rift systems can enter the pre-oceanic rifting stage, during which the rift zone narrows and becomes asymmetric as a consequence of simple-shear deformation at shallow crustal levels and pure shear deformation at lower crustal and mantle-lithospheric levels. Preceding crustal separation, extensional denudation of the lithospheric mantle is possible. Progressive lithospheric attenuation entails updoming of the asthenosphere and thermal doming of the rift shoulders. Their uplift provides a major clastic source for the rift basins and the lateral rift-rim basins. Their stratigraphic record provides a sensitive tool for dating the rift shoulder uplift. Asymmetric rifting leads to the formation of asymmetric continental margins, corresponding in a simple-shear model to an upper plate and a conjugate lower plate margin, as seen in the Central Atlantic passive margins of the United States and Morocco. This rifting model can be successfully applied to the analysis of the Alpine Tethys palaeo-margins (such as Rif and the Western Alps).

Growth mechanisms and timing of emplacement of a vertically layered mafic intrusion in the feeder zone of an ocean island volcano (Fuerteventura, Canary islands)

Résumé pour le grand public L'île de Fuerteventura (Canaries) offre l'occasion rare d'observer les racines d'un volcan océanique édifié il y a 25 à 30 millions d'années et complètement érodé. On y voit de nombreux petits plutons de forme et composition variées, témoignant d'autant d'épisodes de l'activité magmatique. L'un de ces plutons, appelé PX1, présente une structure inhabituelle formée d'une alternance de bandes verticales d'épaisseur métrique à hectométrique de roches sombres de composition pyroxénilique ou gabbroïque. Les pyroxénites résultent clairement de l'accumulation de cristaux de pyroxènes et non de la simple solidification d'un magma? Se pose dès lors la question de la nature du processus qui a conduit à l'accumulation verticale de niveaux concentrés en pyroxènes. En effet, les litages pyroxénitiques classiques sont subhorizontaux, car ils résultent de l'accumulation gravitaire des cristaux séparés du magma dont ils cristalli¬sent par sédimentation. Cette étude vise à identifier et comprendre les mécanismes qui ont engendré ce Iitage minéralogique vertical et l'im¬portant volume de ces faciès cumulatifs. Nous nous sommes également intéressés aux conditions de pression et de température régnant au moment de la mise en place du pluton, ainsi qu'à sa durée de vie et à sa vitesse de refroidis¬sement. Enfin une approche géochimique nous a permis de préciser la nature de la source mantellique des magmas liés à cette activité magmatique. PX1 est en réalité un complexe filonien formé à des conditions de pression et de température de 1-2 kbar et 1050- 1100°C; sa construction a nécessité au moins 150 km3 de magma. L'alternance d'horizons gabbroïques et pyroxéniti¬ques représente des injections successives de magma sous la forme de filons verticaux, mis en place dans un contexte régional en extension. L'étude des orientations des minéraux dans ces faciès révèle que les horizons gabbroïques enregistrent l'extension régionale, alors que les pyroxénites sont générées par une compaction au sein du pluton. Ceci suggère que le régime des contraintes, qui était extensif lors de l'initiation de la mise en place de PX1, est pério¬diquement devenu compressif au sein même du pluton. Cette compression serait liée à des cycles de mise en place où la vitesse de croissance du pluton dépassait celle de l'extension régionale. La différenciation observée au sein de chaque horizon, depuis des pyroxénites riches en olivine jusqu'à des pyroxé¬nites à plagioclase interstitiel et des gabbros, ainsi que la composition géochimique des minéraux qui les constituent suggèrent que chaque filon vertical s'est mis en place à partir d'un magma de composition identique, puis a évolué indépendamment des autres en fonction du régime thermique et du régime des contraintes local. Lorsque le magma en train de cristalliser s'est trouvé en compression, le liquide résiduel a été séparé des cristaux déjà formés et extrait du système, laissant derrière lui une accumulation de cristaux dont la nature et les proportions dépendaient du stade de cristallisation atteint par le magma au moment de l'extraction. Ainsi, les niveaux de pyroxénites à olivine (premier minéral à cristalliser) ont été formés lorsque le magma correspondant était encore peu cristallisé; à l'inverse, les py¬roxénites riches en plagioclase (minéral plus tardif dans la séquence de cristallisation) et certains gabbros à caractère cumulatif résultent d'une compression tardive dans le processus de cristallisation du filon concerné. Les liquides résiduels extraits des niveaux pyroxénitiques sont rarement observés dans PX1, certaines poches et filonets de com¬position anorthositique pourraient en être les témoins. L'essentiel de ces liquides a probablement gagné des niveaux supérieurs du pluton, voire la surface du volcan. L'origine du régime compressif périodique affectant les filons en voie de cristallisation est attribuée aux injections suivantes de magma au sein du pluton, qui se sont succédées à un rythme plus rapide que la vitesse de consolidation des filons. Des datations U/Pb de haute précision sur des cristaux de zircon et de baddeleyite ainsi que40Ar/39Ar sur des cris¬taux d'amphibole révèlent une initiation de la mise en place de PX1 il y a 22.1 ± 0,7 Ma; celle-ci a duré quelque 0,48 ± 0,22 à 0,52 ± 0,29 Ma. Ce laps de temps est compatible avec celui nécessaire à la cristallisation des filons individuels, qui va de moins d'une année lors de l'initiation du magmatisme à 5 ans lors du maximum d'activité de PX1. La présence de cristaux résorbés enregistrant une cristallisation complexe suggère l'existence d'une chambre mag¬matique convective sous-jacente à PX1 et périodiquement rechargée. Les compositions isotopiques des roches étu¬diées révèlent une source mantellique profonde de type point chaud avec une contribution du manteau lithosphéri- que métasomatisé présent sous les îles Canaries. Résumé L'intrusion mafique Miocène PX1 fait partie du soubassement superficiel (0.15-0.2 GPa, 1100 °Q d'un volcan d'île océanique. La particularité de ce pluton est l'existence d'alternances d'unités de gabbros et de pyroxénites qui met¬tent en évidence un litage magmatique vertical (NNE-SSW). Les horizons gabbroiques et pyroxénitiques sont constitués d'unités de différenciation métriques qui suggèrent tine mise en place par injections périodiques de filons verticaux de magma formant un complexe filonien. Chaque filon vertical a subi une différenciation parallèle à un front de solidification sub-vertical parallèle aux bords du filon. Les pyroxénites résultent du fractionnement et de l'accumulation d'olivine ± clinopyroxene ± plagioclase à partir d'un magma basaltique faiblement alcalin et sont interprétées comme étant des imités de différenciation tronquées dont le liquide interstitiel a été extrait par compaction. L'orientation préférentielle des clinopyroxènes dans ces pyroxe- nites (obtenues par analyse EBSD et micro-tomographique) révèle une composante de cisaillement simple dans la genèse de ces roches, ce qui confirme cette interprétation. La compaction des pyroxénites est probablement causée par a mise en place de filons de magma suivants. Le liquide interstitiel expulsé est probablement par ces derniers. Les clinopyroxènes des gabbros, montrent une composante de cisaillement pure suggérant qu'ils sont affectés par une déformation syn-magmatique parallèle aux zones de cisaillement NNE-SSW observées autour de PX1 et liées au contexte tectonique Miocène d'extension régionale. Ceci suggère que les gabbros sont liés à des taux de mise en place faibles à la fin de cycles d'activité magmatique et sont peu ou pas affectés par la compaction. L'initiation et la géométrie de PX1 sont donc contrôlées par le contexte tectonique régional d'extension alors que les taux et les volumes de magma dépendent de facteurs liés à la source. Des taux d'injection élevés résultent probable¬ment en une croissance du pluton supérieure à la place crée par cette extension. Dans ce cas de figure, la propagation des nouveaux dykes et l'inaptitude du magma à circuler à travers les anciens dykes cristallisés pourrait causer une augmentation de la pression non-lithostatique sur ces derniers, exprimée par un cisaillement simple et l'expulsion du liquide interstitiel qu'ils contiennent (documenté par les zones de collecte anorthositiques). Les compositions en éléments majeurs et traces des gabbros et pyroxenites de PX1 sont globalement homogènes et dépendent de la nature cumulative des échantillons. Cependant, de petites variations des concentrations en éléments traces ainsi que les teneurs en éléments traces des bordures de clinopyroxenes suggèrent que ces derniers ont subi un processus de rééquilibrage et de cristallisation in situ. L'homogénéité des compositions chimiques des échantillons, ainsi que la présence de grains de clinopyroxene résorbés suggère que le complexe filonien PX1 s'est mis en place au dessus d'une chambre magmatique périodiquement rechargée dans laquelle la convection est efficace. Chaque filon est donc issu d'un même magma, mais a subi une différenciation par cristallisation in situ (jusqu'à 70% de fraction¬nement) indépendamment des autres. Dans ces filons cristallisés, les minéraux cumulatifs subissent un rééquilibrage partiel avec les liquide interstitiel avant que ce dernier ne soit expulsé lors de la compaction (mettant ainsi un terme à la différenciation). Ce modèle de mise en place signifie qu'un minimum de 150Km3 de magma est nécessaire à la genèse de PX1, une partie de ce volume ayant été émis par le 'Central Volcanic Complex' de Fuerteventura. Les rapports isotopiques radiogéniques mesurés révèlent la contribution de trois pôles mantelliques dans la genèse du magma formant PX1. Le mélange de ces pôles HIMU, DMM et EM1 refléterai l'interaction du point chaud Cana¬rien avec un manteau lithosphérique hétérogène métasomatisé. Les petites variations de ces rapports et des teneurs en éléments traces au sein des faciès pourrait refléter des taux de fusion partielle variable de la source, résultant en un échantillonnage variable du manteau lithosphérique métasomatisé lors de son interaction avec le point chaud. Des datations U/Pb de haute précision (TIMS) sur des cristaux de zircon et de baddeleyite extraits de gabbros de PX1 révèlent que l'initiation de la cristallisation du magma a eu lieu il y a 22.10±0.07 Ma et que l'activité magmatique a duré un minimum de 0.48 à 0.52 Ma. Des âges 40Ar/39Ar obtenus sur amphibole sont de 21.9 ± 0.6 à 21.8 ± 0.3 Ma, identiques aux âges U/Pb. La combinaison de ces méthodes de datations, suggère que le temps maximum nécessaire à PX1 pour se refroidir en dessous de la température de fermeture de l'amphibole est de 0.8Ma. Ceci signifie que la durée de vie de PX1 est de 520 000 à 800 000 ans. La coexistence de cristaux de baddeleyite et de zircon dans un gabbro est attribuée à son interaction avec un fluide riche en C02 relâché par les carbonatites encaissantes lors du métamorphisme de contact généré par la mise en place de PX1 environ 160 000 ans après le début de sa mise en place. Les durées de vie obtenue sont en accord avec le modèle de mise en place suggérant une durée de cristallisation poux chaque filon allant de 1 an à 5 ans. Abstract The Miocene PX1 gabbro-pyroxenite intrusion (Fuerteventura, Canary Islands), is interpreted as the shallow-level feeder-zone (0.15-0.2 GPa and 1100-1120°C), to an ocean island volcano. The particularity of PX1 is that it displays a NNE-SSW trending vertical magmatic banding expressed by alternating gabbro and pyroxeriite sequences. The gabbro and pyroxenite sequences consist of metre-thick differentiation units, which suggest emplacement by pe¬riodic injection of magma pulses as vertical dykes that amalgamated, similarly to a sub-volcanic sheeted dyke com¬plex. Individual dykes underwent internal differentiation following a solidification front (favoured by a significant lateral/horizontal thermal gradient) parallel to the dyke edges. Pyroxenitic layers result from the fractionation and accumulation of clinopyroxene ± olivine ± plagioclase crystals from a mildly alkaline basaltic liquid and are interpre¬ted as truncated differentiation sequences, from which residual melts were extracted by compaction. Clinopyroxene mineral orientation in pyroxenites (evidenced by EBSD and micro X-ray tomography analysis) display a marked pure shear component, supporting this interpretation. Compaction and squeezing of the crystal mush is ascribed to the incoming and inflating magma pulses. The resulting expelled interstitial liquid was likely collected and erupted along with the magma flowing through the newly injected dykes. Gabbro sequences represent crystallised coalesced magma batches, emplaced at lower rates at the end of eruptive cycles, and underwent minor melt extraction as evi¬denced by clinopyroxene orientations that record a simple shear component suggesting syn-magmatic deformation parallel to observed NNF.-SSW trending shear-zones induced by the regional tensional Miocene stress-field. The initiation and geometry of PX1 is controlled by the regional extensional tectonic regime whereas rates and vo¬lumes of magma depend on source-related factors. High injection rates are likely to induce intrusion growth rates larger than could be accommodated by the regional extension. In this case, dyke tip geometry and the inability of magma to circulate through previously emplaced and crystallised dykes could result in an increase of non-lithostatic pressure on previously emplaced mushy dyke walls; generating strong pure-shear compaction and interstitial melt expulsion within the feeder-zone as recorded by the cumulitic pyroxenite bands and anorthositic collection zones. The whole-rock major and trace-element chemistry of PX1 gabbros and pyroxenites is globally homogeneous and controlled by the cumulate nature of the samples (i.e. on the modal proportions of olivine, pyroxene, plagioclase and oxides). However, small variations of whole-rock trace-element contents as well as trace-element contents of clinopyroxene rims suggest that in-situ re-equilibration and crystallisation has occurred. Additionally, the global homogeneity and presence of complex zoning of rare resorbed clinopyroxene crystals suggest that the PX1 feeder- zone overlies a periodically replenished and efficiently mixed magma chamber. Each individual dyke of magma thus originated from a compositionally constant mildly alkaline magma and differentiated independently from the others reaching up to 70% fractionation. Following dyke arrest these are affected by interaction with the trapped interstitial liquid prior to its compaction-linked expulsion (thus stopping the differentiation process). This emplacement model implies that minimum amount of approximately 150 km3 of magma is needed to generate PX1, part of it having been erupted through the overlying Central Volcanic Complex of Fuerteventura. The radiogenic isotope ratios of PX1 samples reveal the contribution on three end-members during magma genesis. This mixing of the H1MU, EMI and DMM end-members could reflect the interaction of the deep-seated Canarian mantle plume with a heterogeneous metasomatic and sepentininsed lithospheric mantle. Additionally, the observed trace-element and isotopic variations within the same fades groups could reflect varying degrees of partial melting of the source region, thus tapping more or less large areas of the metasomatised lithospheric mantle during interac¬tion with the plume. High precision ID-TIMS U/Pb zircon and baddeleyite ages from the PX1 gabbro samples, indicate initiation of magma crystallisation at 22.10 ± 0.07 Ma. The magmatic activity lasted a minimum of 0.48 to 0.52 Ma. 40Ar/39Ar amphibole ages are of 21.9 ± 0.6 to 21.8 ± 0.3, identical within errors to the U/Pb ages. The combination of the 40Ar/39Ar and U/Pb datasets imply that the maximum amount of time PX1 took to cool below amphibole Tc is 0.8 Ma, suggesting PX1 lifetime of 520 000 to 800 000 years. On top of this, the coexistence of baddeleyite and zircon in a single sample is ascribed to the interaction of PX1 with C02-rich carbonatite-derived fluids released from the host-rock carbonatites during contact metamorphism 160 000 years after PX1 initiation. These ages are in agreement with the emplacement model, implying a crystallisation time of less than 1 to 5 years for individual dykes.

Anisotropic model for granulated sea ice dynamics

A continuum model describing sea ice as a layer of granulated thick ice, consisting of many rigid, brittle floes, intersected by long and narrow regions of thinner ice, known as leads, is developed. We consider the evolution of mesoscale leads, formed under extension, whose lengths span many floes, so that the surrounding ice is treated as a granular plastic. The leads are sufficiently small with respect to basin scales of sea ice deformation that they may be modelled using a continuum approach. The model includes evolution equations for the orientational distribution of leads, their thickness and width expressed through second-rank tensors and terms requiring closures. The closing assumptions are constructed for the case of negligibly small lead ice thickness and the canonical deformation types of pure and simple shear, pure divergence and pure convergence. We present a new continuum-scale sea ice rheology that depends upon the isotropic, material rheology of sea ice, the orientational distribution of lead properties and the thick ice thickness. A new model of lead and thick ice interaction is presented that successfully describes a number of effects: (i) because of its brittle nature, thick ice does not thin under extension and (ii) the consideration of the thick sea ice as a granular material determines finite lead opening under pure shear, when granular dilation is unimportant.

Emplacement setting of the granite sheeted pluton of Esperanca (Brasiliano orogen, Northeastern Brazil)

Anisotropy of magnetic susceptibility (AMS) and isotopic (U-Pb, Sm-Nd) data were combined to study the emplacement setting of the granite sheets that constitute the Esperanca pluton in the Borborema Province (Northeastern Brazil). The sheets dip moderately to the SE along the contact zone between the Paleoproterozoic basement rocks and Early Neoproterozoic orthogneisses and metasediments. Granite fabrics were determined mainly using AMS in 136 sites distributed within the central and western part of the pluton. The sheets normally have susceptibility lower than 0.35 mSI but, locally, where a Ti-poor magnetite appears with titanite, the susceptibility increases up to 5 mSI. Comparison between the silicate fabric and AMS showed inconsistencies between the shape of mineral and magnetic ellipsoids despite of their orientations that fit fairly well to each other. AMS indicated the deformation was partitioned between the lower (tonalite, syenogranite) and upper (leucogranite and coarse porphyritic granite) sheets. In the lower sheets the curvilinear lineation trajectory is attributed to a dominant heterogeneous pure shear event that flattened laterally the still molten tonalite and syenogranite into the regional foliation. ne associated microstructures are typically magmatic. Zircon U/Pb data of the syenogranite yielded a crystallization age of 592 +/- 5 Ma. In the upper sheets the fabric recorded a component of simple shear deformation that displaced the coarse porphyritic granite and the top gneissic host rocks to the southwest. Microstructures are mostly of post-full crystallization type. T(DM) model ages and epsilon(Nd) (t = 0) values indicate that the magma contaminated by partial melting of the regional host rocks. Sheet propagation at the emplacement level would have exploited the contact zone between crustal blocks of different rheologies when the melt pressures would be able to tensionally fail the anisotropy of the host rocks. (C) 2004 Elsevier B.V. All rights reserved.

Aspectos microestruturais e texturais dos metassedimentos da formacao eleuterio

This work describes the primary and tectonic-metamorphic structures of the Eleuterio Formation, cropping 1 km NW of the village of Eleuterio, State of Sao Paulo. The structural feature have been studied chiefly in low grade metamorphic siltites, arkoses and conglomerates. The textural evolution is marked by fragmentation, clay minerals reaction, pression solution with silica recrystallization, mechanical rotation in minerals, fluid circulation and dissolution, mica beards, the possibily crystallization of biotite and epidote, and so on. The tectonic metamorphic foliation now described is supposed to be formed by simple shear with a possible pure shear component. -English summary