Electric current of an electrified jet issuing from a long metallic tube.

This paper presents an analysis of the transport of electric current in a jet of an electrically conducting liquid discharging from a metallic tube into a gas or a vacuum, and subject to an electric field due to a high voltage applied between the tube and a far electrode. The flow, the surface charge and the electric field are computed in the current transfer region of the jet, where conduction current in the liquid becomes surface current due to the convection of electric charge accumulated at its surface. The electric current computed as a function of the flow rate of the liquid injected through the tube increases first as the square root of this flow rate, levels to a nearly constant value when the flow rate is increased and finally sets to a linear increase when the flow rate is further increased. The current increases linearly with the applied voltage at small and moderate values of this variable, and faster than linearly at high voltages. The characteristic length and structure of the current transfer region are determined. Order-of-magnitude estimates for jets which are only weakly stretched by the electric stresses are worked out that qualitatively account for some of the numerical results.

Comparison of metallic and ceramic tubes as atomization cells for tin determination by TS-FF-AAS

This work describes the development of an analytical procedure for on-line tin determination using thermospray flame furnace atomic absorption spectrometry (TS-FF-AAS). Two tubes were evaluated as atomization cells: a metallic tube (Ni-Cr, principal components composition: 73.95% Ni and 16.05% Cr) and a ceramic tube (99.8% Al2O3). The use of air as the carrier was made by employing a Rheodyne valve to inject the samples, allowing an analytical frequency of 90 h(-1) and avoiding sample dispersion. The carrier flow rate (air), sample volume injected, and acid concentration (HCl) were evaluated for the optimization of the TS-FF-AAS system. The sensitivity for 50 mL of analytical solution with TS-FF-AAS was 2 and 5 times higher (to metallic and ceramic tube, respectively) than using an acetylene-nitrous oxide flame with pneumatic aspiration (requiring a sample volume of approximately 20 times higher.

Investigations into the use of the finite element method and artificial neural networks in the non-destructive analysis of metallic tubes

This work presents an investigation into the use of the finite element method and artificial neural networks in the identification of defects in industrial plants metallic tubes, due to the aggressive actions of the fluids contained by them, and/or atmospheric agents. The methodology used in this study consists of simulating a very large number of defects in a metallic tube, using the finite element method. Both variations in width and height of the defects are considered. Then, the obtained results are used to generate a set of vectors for the training of a perceptron multilayer artificial neural network. Finally, the obtained neural network is used to classify a group of new defects, simulated by the finite element method, but that do not belong to the original dataset. The reached results demonstrate the efficiency of the proposed approach, and encourage future works on this subject.

Espectrofotometría de absorción atómica con tubo en la llama: aplicación en la determinación total de cadmio, plomo y zinc en aguas frescas, agua de mar y sedimentos marinos

Thermospray flame furnace Atomic Absorption Spectrometry (TS-FF-AAS) was used for the total determination of Cd, Pb and Zn in fresh water and seawater samples at µg L-1 levels, and in marine sediment samples at µg g-1 levels. Using a sample loop of 50 µL and a peristaltic pump the samples were transported into the metallic tube placed over an air/acetylene flame, through a ceramic capillary (o.d. = 3.2 mm) containing two parallel internal orifices (i.d = 0.5 mm). The detection limits determined for Cd, Pb and Zn using a synthetic water matrix (2.5% m/v NaCl, 0.5% m/v MgCl2 and 0.8% m/v CaCl2) were 0.32 µg L-1; 2.6 µg L-1 and 0.21 µg L-1 respectively. The methodology by TS-FF-AAS was validated by determination of Cd, Pb and Zn in certified reference materials of water and marine sediment, and the t-test for differences between means was applied. No statistically significant differences were established in fresh water and seawater (p>0.05), whereas differences became apparent in marine sediment (p<0.03).

Implante endoscópico no esôfago distal de polimetilmetacrilato para controle do refluxo gastrofágico : estudo experimental em modelo animal

XIXA doença do refluxo gastroesofágico (DRGE) comumente afeta o esôfago e provavelmente é a condição mais prevalente no segmento alto do trato gastrointestinal, acometendo entre 5 e 45% da população ocidental. A terapêutica atual para essa doença além de medidas gerais e dietéticas, inclui tratamento farmacológico e/ou cirurgia. Ambos podem ser eficazes, mas apresentam elevado custo financeiro. O tratamento com fármacos pode apresentar baixa aderência medicamentosa e a cirurgia tem baixa, mas não desprezível, morbidade e mortalidade. Idealmente o tratamento da DRGE deveria ser eficaz, com baixo risco e com baixo custo. Objetivos: 1. Desenvolver um modelo experimental em suínos para o estudo do Refluxo Gastroesofágico através da Pressão e do Volume de Vazão Gástricos; 2. Avaliar a eficácia do implante endoscópico de PMMA ao nível do Esfíncter Esofágico Inferior (EEI) para aumentar a Pressão de Vazão Gástrica, o Volume de Vazão Gástrico e a Pressão Basal do EEI; 3. Descrever as reações histológicas associadas ao implante de PMMA. Material e Métodos: Suínos da raça Large White, do sexo feminino com 8 semanas de vida foram estudados no experimento. Foi realizada manometria do esfíncter esofágico inferior com registro da pressão basal com cateter de perfusão com água e técnica de retirada lenta. Calculou-se, também, a extensão do EEI. Após, gastrostomia era realizada com colocação intragástrica da extremidade distal de uma sonda de Foley com três vias e um cateter de pHmetria esofágica introduzido via oral com o sensor distal posicionado 5 cm acima do bordo superior de esfíncter esofágico inferior. Iniciava-se, XXentão, a infusão contínua no estômago de uma solução de HCl a 0,02N com medida e registro simultâneos da Pressão e do Volume de Vazão Gástricos e do pH esofágico. Definiu-se a Pressão de Vazão Gástrica (PVG) e o Volume de Vazão Gástrico quando houve brusca e sustentada acidificação do esôfago distal (pH<3). Após, introduzia-se um tubo metálico (Tubo Introdutor ou TI) via oral e, em seguida, o endoscópio, seguindo ambos até o esôfago distal. Cateter de nylon com agulha calibre 16 era introduzido pelo tubo introdutor e o PMMA implantado na área correspondente ao EEI com uma pistola dosadora volumétrica que permitia a injeção de volumes prédeterminados em 3 ou 4 pontos da submucosa (total por ponto = 0,73 ml de PMMA). As medidas de PVG, VVG e pressão basal do EEI foram repetidas após 28 dias, sacrificando-se os animais e removendo-se esôfago médio e distal, junção esofagogástrica, fundo e corpo gástricos para estudo histológico. Previamente ao experimento, três projetos pilotos foram desenvolvidos. O primeiro designado como “Projeto Piloto: Refluxo Gastroesofágico por pHmetria de 24H” (RGE 24H) buscou a via de acesso transnasal para registro de pHmetria por 24 horas. No segundo, designado “Projeto Piloto: Esofagostomia”, para confirmação de refluxo gastroesofágico espontâneo em suínos da raça Large White, utilizou-se anestesia com associação de tiletamina 125 mg e zolazepam 125 mg em combinação com um sedativo, a xilazina a 2% . A pHmetria foi mantida por 24 horas. Os dados descritos por Kadirkamanathan et al. não foram reproduzidos no nosso laboratório. Optou-se então pela realização de um terceiro projeto, “Projeto Piloto: Gastrostomia” para induzir refluxo gastroesofágico através de um modelo experimental e testar a reprodutibilidade da Pressão de Vazão Gástrica. Obteve-se sucesso. Resultados: Trinta e sete animais foram estudados em 60 intervenções no Laboratório de motilidade experimental. O projeto piloto “RGE:24h” foi abandonado após perda de 5 animais pela anestesia com halotano e, solucionada esta questão, a sistemática infecção do tecido celular subcutâneo nasal, dificultando a manutenção do cateter de phmetria em outros 5 animais. No “Projeto Piloto: Esofagostomia”, em cinco animais estudados (cada animal em duas ocasiões diferentes) não se reproduziram os achados de refluxo espontâneo. No terceiro projeto “Projeto Piloto: Gastrostomia” quatro animais foram estudados em dois momentos diferentes obtendo-se sucesso e reprodutibilidade XXIdos dados. Criado o modelo experimental, quatorze suínos foram submetidos ao experimento com implante endoscópico de PMMA com os seguintes resultados: A média dos pesos com 8 semanas de idade foi 14,98 ± 2,43 e 28 dias após o implante, 20,26 ± 3,68. O ganho ponderal foi considerado normal para a espécie. A Pressão de Vazão Gástrica média no dia 1 foi 8,08 mmHg e no dia 28, 10,69mmHg (Teste t de Student: t = 2,72 gl = 13 p = 0,017). Os Volumes de Vazão Gástricos médios foram: 392,86 ml para o dia 1 e 996,71 ml no dia 28 (teste t de Student: t = 11,66 gl = 13 p< 0,001). A Pressão Basal do EEI e o comprimento do esfíncter, não apresentaram diferenças estatisticamente significativas. PMMA foi identificado como depósitos de grandes vacúolos no tecido intersticial ao exame histológico da junção esofagogástrica associado a histiócitos, plasmócitos e presença de células gigantes tipo Langhans indicando reação tecidual de corpo estranho em todos os animais. Fibrose e macrófagos com vacúolos intracelulares estiveram presentes em menor freqüência. Conclusões: 1. O modelo experimental, em suínos, desenvolvido viabilizou o estudo do Refluxo Gastroesofágico através da Pressão de Vazão Gástrica e Volume de Vazão Gástrico; 2. O implante de PMMA, no presente estudo, aumentou a Pressão de Vazão e o Volume de Vazão Gástricos, mas não a Pressão Basal do EEI, nem tampouco aumentou o seu comprimento; 3. Depósito de PMMA implantado e evidência de processo inflamatório crônico e reação tecidual de corpo estranho foi encontrada no local do implante de PMMA. Macrófagos com vacúolos intracelulares e fibrose foram encontrados com menos freqüência.

Sistema TS-FF-AAS com chama acetileno-ar como alternativa em relação à chama acetileno-óxido nitroso em FAAS na determinação de estanho

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A steady-state model for heat pipes of circular or rectangular cross-sections

The objective of this paper is to present a generalized analytical-numerical model of the internal flow in heat pipes. The model formulation is based on two-dimensional formulation of the energy and momentum equations in the vapour and liquid regions and also in the metallic tube. The numerical solution of the model is obtained by using the descretization scheme LOAD and the SIMPLE numerical code. The flow fields, as well as the pressure fields, for different geometries were obtained and discussed. Copyright © 1996 Elsevier Science Ltd.

Identificação de defeitos em tubulações metálicas utilizando redes neurais artificiais e o método dos elementos finitos

Pós-graduação em Engenharia Mecânica - FEB

The influence of handrim design on the contact forces on hands'surface: a preliminary study

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

On the derivation of the terminal velocity for the falling magnet from dimensional analysis

Dimensional analysis was employed to develop a predictive formula for the terminal velocity for a magnet dropped down a metallic tube. In this particular application, the technique succeeded in generating the same formula theoretically derived and that has been published by others. The analysis thus presented suggests other applications that can be developed for motivating in the use of the technique.

Emission and holographic interferometry measurements in a superorbital expansion tube

Free-piston-driven expansion tubes are capable of generating flaw conditions over a wide range of enthalpies ranging from orbital up to superorbital velocities. Initial optical measurements aimed at investigating the flow in such a facility are presented. Emission studies were used to identify impurities in the how and to investigate spectral regions that are accessible by optical techniques. At moderate enthalpies, it was found that significant radiation resulted from metallic contaminants. At high enthalpies, the spectrum consisted of a number of atomic lines together with a broadband background component indicative of the presence of electrons. The presence of this radiation may limit the applicability of optical techniques that require spectral regions free from the influence of atomic transitions or background radiation. Emission spectroscopy (through Stark broadened hydrogen lines) and two-wavelength holographic interferometry were used to measure the electron number density behind a bow shock on a blunt body at conditions where significant ionization was observed. They yielded average concentrations of (3 +/- 1) x 10(17) cm(-3) from the emission measurements and (3.8 +/- 0.6) x 10(17) cm(-3) from the interferometry.

Influence of the yielding criterion on total forming force in metallic junctions using elastomers

The production of metallic junctions employing elastomers is an unconventional technique that has been in development in the last 20 years. The forming process gets successfull just if a simultaneous compression between the elastomers and the tube takes place. Exact solutions for problems involving forming with elastomers are quite difficult to determine. However, the upper-bound theory can be used in order to predict the necessary load for junctions forming. Thus, it is necessary to develop a model capable to provide an estimate of the total forming force, which is useful to set-up tools and equipments required for the process. In this work, Von Mises, Hill's 1948 and Hill's 1979 associated yielding theories, and the Hosford's theory (1979) as well, were used in order to study the anisotropic behaviour on total forming force of junctions using elastomers, insuring the functionality of the proposed model. (c) 2006 Elsevier B.V. All rights reserved.

Effectiveness Of The Endotracheal Tube Cuff On The Trachea: Physical And Mechanical Aspects.

The inflation pressure of the endotracheal tube cuff can cause ischemia of the tracheal mucosa at high pressures; thus, it can cause important tracheal morbidity and tracheal microaspiration of the oropharyngeal secretion, or it can even cause pneumonia associated with mechanical ventilation if the pressure of the cuff is insufficient. In order to investigate the effectiveness of the RUSCH® 7.5 mm endotracheal tube cuff, this study was designed to investigate the physical and mechanical aspects of the cuff in contact with the trachea. For this end, we developed an in vitro experimental model to assess the flow of dye (methylene blue) by the inflated cuff on the wall of the artificial material. We also designed an in vivo study with 12 Large White pigs under endotracheal intubation. We instilled the same dye in the oral cavity of the animals, and we analyzed the presence or not of leakage in the trachea after the region of the cuff after their deaths (animal sacrifice). All cuffs were inflated at the pressure of 30 cmH2O. We observed the passage of fluids through the cuff in all in vitro and in vivo experimental models. We conclude that, as well as several other cuff models in the literature, the RUSCH® 7.5 mm tube cuffs are also not able to completely seal the trachea and thus prevent aspiration of oropharyngeal secretions. Other prevention measures should be taken.

Influence of dental metallic artifact from multislice CT in the assessment of simulated mandibular lesions

OBJECTIVE: This study evaluated the influence of metallic dental artifacts on the accuracy of simulated mandibular lesion detection by using multislice technology. MATERIAL AND METHODS: Fifteen macerated mandibles were used. Perforations were done simulating bone lesions and the mandibles were subjected to axial 16 rows multislice CT images using 0.5 mm of slice thickness with 0.3 mm interval of reconstruction. Metallic dental restorations were done and the mandibles were subjected again to CT in the same protocol. The images were analyzed to detect simulated lesions in the mandibles, verifying the loci number and if there was any cortical perforation exposing medullar bone. The analysis was performed by two independent examiners using e-film software. RESULTS: The samples without artifacts presented better results compared to the gold standard (dried mandible with perforations). In the samples without artifacts, all cortical perforation were identified and 46 loci were detected (of 51) in loci number analysis. Among the samples with artifacts, 12 lesions out of 14 were recognized regarding medullar invasion, and 40 out of 51 concerning loci number. The sensitivity in samples without artifacts was 90% and 100% regarding loci number and medullar invasion, respectively. In samples with artifacts, these values dropped to 78% and 86%, respectively. The presence of metallic restorations affected the sensitivity values of the method, but the difference was not significant (p>0.05). CONCLUSIONS: Although there were differences in the results of samples with and without artifacts, the presence of metallic restoration did not lead to misinterpretation of the final diagnosis. However, the validity of multislice CT imaging in this study was established for detection of simulated mandibular bone lesions.

Unconventional metallic behavior and superconductivity in the K-Mo-O system

Transport properties and magnetization measurements of the K(x)MoO(2-delta) (0 <= x <= 0.25) compound are reported. The compound crystallizes in the oxygen deficient MoO(2) monoclinic structure with potassium atoms occupying interstitial positions. An unconventional metallic behavior with power-law temperature dependence is related to a magnetic ordering. Superconducting transition with small volume fraction is also observed near 7 K for a sample with low potassium composition.