X-ray diffraction characterisation of expanded austenite and ferrite in plasma nitrided stainless steels

The S phase, known as expanded austenite, is formed on the surfaces of austenitic stainless steels that are nitrided under low temperature plasma. A similar phase was observed for nitrided ferritic stainless steels and was designed as expanded ferrite or ferritic S phase. The authors treated samples of austenitic AISI 304L and AISI 316L and ferritic AISI 409 stainless steels by plasma nitriding at different temperatures and then studied the structural, morphological, chemical and corrosion characteristics of the modified layers by X-ray diffraction, scanning electron microscopy/energy dispersive spectroscopy and electrochemical tests. For both austenitic AISI 304L and AISI 316L stainless steels, the results showed that a hard S phase layer was formed on the surfaces, promoting an anodic polarisation curve displacement to higher current density values that depend on the plasma nitriding temperature. A layer having a high amount of nitrogen was formed on the ferritic AISI 409 stainless steel. X-ray diffraction measurements indicated high strain states for the modified layers formed on the three stainless steels, being more pronounced for the ferritic S phase.

Adsorção de fenol e benzeno em montmorilonita modificada com brometo de hexadeciltrimetilamônio

Este estudo avalia a intercalação de esmectita dioctahédrica do Estado Acre com o sal quaternário de amônio brometo de hexadeciltrimetilamônio (HDTMA) em concentrações compreendidas entre 1 a 5 vezes ao valor de CTC da argila original e sua aplicabilidade na adsorção de fenol e benzeno em fase líquida. Os materiais foram caracterizados por microanálises de difração de raios X, microscopia eletrônica de varredura/espectroscopia com dispersão de energia e espectroscopia na região do infravermelho. Os processos de adsorção foram realizados em sistemas simples e as medidas das concentrações do fenol e benzeno foram efetuadas por espectrofotometria na região ultravioleta. Os resultados indicaram que a intercalação da esmectita com HDTMA propiciou cerca de 78,8% de expansão (variação de d₀₀₁: 1,47 nm para 1,91 nm) e decréscimo acentuado dos elementos das posições interlamelares, como Na, Ca, Mg e K, acompanhado pela delaminação/esfoliação da argila original. Nos processos de adsorção do fenol e benzeno em HDTMA-arg 5 foram obtidos os seguintes resultados: q_Max= 4,44 e 35,8 mg.g^-1; K_L= 0,076 e 0,115 L.g-1; ΔGº = -16,85 e -18,38 kJ.mol^-1, respectivamente. Estes dados indicaram que os processos de adsorção do benzeno e fenol em fase líquida na organoargila HDTMA-arg 5 foram favoráveis, espontâneos e com interações físicas.

Obtenção e caracterização de filmes finos de Bi3NbO7 pelo método dos precursores poliméricos

Pós-graduação em Engenharia Mecânica - FEG

Enhanced UV emission from ZnO nanoflowers synthesized by the hydrothermal process

ZnO nanoflowers were synthesized by the hydrothermal process at an optimized growth temperature of 200 ◦C and a growth/reaction time of 3 h. As-prepared ZnO nanoflowers were characterized by x-ray diffraction, scanning electron microscopy, UV–visible and Raman spectroscopy. X-ray diffraction and Raman studies reveal that the as-synthesized flower-like ZnO nanostructures are highly crystalline with a hexagonal wurtzite phase preferentially oriented along the (1 0 1 1) plane. The average length (234–347 nm) and diameter (77–106 nm) of the nanorods constituting the flower-like structure are estimated using scanning electron microscopy studies. The band gap of ZnO nanoflowers is estimated as 3.23 eV, the lowering of band gap is attributed to the flower-like surface morphology and microstructure of ZnO. Room temperature photoluminescence spectrum shows a strong UV emission peak at 392 nm, with a suppressed visible emission related to the defect states, indicating the defect free formation of ZnO nanoflowers that can be potentially used for UV light-emitting devices. The suppressed Raman bands at 541 and 583 cm−1 related to defect states in ZnO confirms that the ZnO nanoflowers here obtained have a reduced presence of defects

Red, green, and blue lanthanum phosphate phosphors obtained via surfactant-control led hydrothermal synthesis

A new solution route for the obtainment of highly pure luminescent rare-earth orthophosphates in hydrothermal conditions was developed. By starting from soluble precursors (lanthanide tripolyphosphato complexes. i.e. with P(3)O(10)(5) as a complexing agent and as in orthophosphate source) and by applying surfactants in a water/toluene medium, the precipitations are confined to reverse micelle structures, thus yielding nanosized and homogeneous orthophosphates The method was employed to obtain lanthanide-activated lanthanum phosphates, which can be applied as red (LaPO(4):Eu(3+)), green (LaPO(4):Ce(3+), Tb(3+)) and blue (LaPO(4):Tm(3+)) phosphors The produced materials were analyzed by powder X-ray diffractometry, scanning electron microscopy, infrared spectroscopy and luminescence spectroscopy (emission, excitation, lifetimes and chromaticity coordinates) (C) 2009 Elsevier B V All rights reserved

UTILIZAÇÃO DO COMPÓSITO NANOESTRUTURADO SIO2/TIO2NA FOTODEGRADAÇÃO DE CORANTES TÊXTEIS COM LUZ SOLAR NATURAL

SiO2/TiO2 nanostructured composites with three different ratios of Si:Ti were prepared using the sol-gel method. These materials were characterized using energy dispersive X-ray fluorescence, Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, photoluminescence, Raman with Fourier transform infrared spectroscopy, and the specific surface area. The band gaps of materials were determined by diffuse reflectance spectra, and the values of 3.20 ± 0.01, 2.92 ± 0.02, and 2.85 ± 0.01 eV were obtained as a result of the proportional increases in the amount of Ti within the composite. The materials exhibit only the anatase (TiO2) crystalline phase and have crystalline domains ranging from 4 to 5 nm. The photodegradation process of methylene blue, royal blue GRL, and golden yellow GL dyes were studied with respect to their contact times, pH variations within the solution, and the variations in the dye concentration of the solution in response to only sunlight. The maximum amount of time for the mineralization of dyes was 90 min. The kinetics of the process follows an apparently first order model, in which the obtained rate constant values were 5.72 × 10-2 min-1 for methylene blue, 6.44 × 10-2min-1 for royal blue GRL, and 1.07 × 10-1min-1 for golden yellow.

Miscibility studies of the blends of chitosan with some cellulose ethers

The polymeric films have been prepared based on blends of chitosan with two cellulose ethers-hydroxypropylmethylcellulose and methylcellulose by casting from acetic acid solutions. The films were transparent and brittle in a dry state but an immersion of the samples in deionized water for over 24 h leads to their disintegration or partial dissolution. The miscibility of the polymers in the blends has been assessed by infrared spectroscopy, wide-angle X-ray diffraction, scanning electron microscopy and thermal gravimetric analysis. It was shown that although weak hydrogen bonding exists between the polymer functional groups the blends are not fully miscible in a dry state. (c) 2005 Elsevier Ltd. All rights reserved.

Luminescence and defect centres in MgSrAl(10)O(17):Sm(3+) phosphor

An efficient reddish orange emission MgSrAl(10)O(17):Sm(3+) phosphor was prepared by the combustion method. The phosphor has been characterized by X-ray diffraction, scanning electron microscopy, thermogravimetric analysis measurements. Photoluminescence spectrum revealed that samarium ions are present in trivalent oxidation states. The phosphor exhibits two thermally stimulated luminescence (TSL) peaks at 210 degrees C and 450 degrees C. Electron spin resonance studies were carried out to identify the defect centres responsible for the TSL process in MgSrAl(10)O(17):Sm(3+) phosphor. Three defect centres have been identified in irradiated phosphor and these centres are tentatively assigned to an O(-) ion and F(+) centres. O(-) ion (hole centre) correlates with the 210 degrees C TSL peak while one of the F+ centres (electron centre) appears to relate to the 450 degrees C TSL peak. (C) 2010 Elsevier B.V. All rights reserved.

Conversão térmica e termocatalítica à baixa temperatura do óleo de girassol para obtenção de bio-óleo

The use of biofuels remotes to the eighteenth century, when Rudolf Diesel made the first trials using peanut oil as fuel in a compression ignition engine. Based on these trials, there was the need for some chemical change to vegetable oil. Among these chemical transformations, we can mention the cracking and transesterification. This work aims at conducting a study using the thermocatalytic and thermal cracking of sunflower oil, using the Al-MCM-41 catalyst. The material type mesoporous Al-MCM-41 was synthesized and characterized by Hydrothermical methods of X-ray diffraction, scanning electron microscopy, nitrogen adsorption, absorption spectroscopy in the infrared and thermal gravimetric analysis (TG / DTG).The study was conducted on the thermogravimetric behavior of sunflower oil on the mesoporous catalyst cited. Activation energy, conversion, and oil degradation as a function of temperature were estimated based on the integral curves of thermogravimetric analysis and the kinetic method of Vyazovkin. The mesoporous material Al-MCM-41 showed one-dimensional hexagonal formation. The study of the kinetic behavior of sunflower oil with the catalyst showed a lower activation energy against the activation energy of pure sunflower oil. Two liquid fractions of sunflower oil were obtained, both in thermal and thermocatalytic pyrolisis. The first fraction obtained was called bio-oil and the second fraction obtained was called acid fraction. The acid fraction collected, in thermal and thermocatalytic pyrolisis, showed very high level of acidity, which is why it was called acid fraction. The first fraction was collected bio-called because it presented results in the range similar to petroleum diesel

Preparation and structural characterization of vulcanized natural rubber nanocomposites containing nickel-zinc ferrite nanopowders

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Photoelectrochemical properties of FTO/m-BiVO4 electrode in different electrolytes solutions under visible light irradiation

Photoelectrochemical properties of FTO/BiVO4 electrode were investigated in different electrolytic solutions, potassium chloride (KCl) and sodium sulphate (Na2SO4), and under visible light irradiation condition. In order to accomplish that, an FTO/BiVO4 electrode was built by combining the solution combustion synthesis technique with the dip-coating deposition process. The morphology and structure of the BiVO4 electrode were investigated through X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy. Photoelectrochemical properties were analyzed through chronoamperometry measurements. Results have shown that the FTO/BiVO4 electrode presents higher electroactivity in the electrolyte Na2SO4, leading to better current stabilization, response time, and photoinduced current density, when compared to KCl electrolyte. Besides, this electrode shows excellent performance for methylene blue degradation under visible light irradiation condition. In Na2SO4, the electrode has shown higher degradation rate, 51 %, in contrast to 44 % in KCl, plus higher rate constant, 174 × 10-4 min-1 compared to 150 × 10-4 min-1 in KCl. Results presented in this communication leads to the indication of BiVO4 thin films as alternate materials to use in heterogeneous photoelectrocatalysis, more specifically in decontamination of surface water. © 2013 Springer-Verlag Berlin Heidelberg.

Produção de carvão ativado a partir da biomassa residual da castanha do Brasil (Bertholletia excelsa L.) para adsorção de cobre (II)

Produziu-se carvão ativado a partir da casca da castanha-do-Brasil (Bertholletia excelsa L.) para ser utilizado na remoção de cobre (II), no processo de adsorção em sistema de batelada. A casca é resíduo do beneficiamento da castanha, que foi coletada, selecionada, lavada em água corrente e depois secada em estufa a 150ºC por 24 h. Os carvões foram carbonizados a 400 ºC por 3 h e ativados termicamente a 800ºC em tempos de 1, 2 e 3 h, quando receberam as respectivas codificaçõesCA1, CA2 e CA3. Depois foram caracterizadas quanto: à área superficial específica, ao volume e tamanho de poros, à difração de raios-X, à microscopia eletrônica de varredura (MEV) acoplada ao EDS(sistema de energia dispersiva por raios-X) e à espectroscopia de infravermelho com transformada de Fourier (FTIR). Ensaios preliminares foram realizados para avaliar a eficiência dos carvões quanto à remoção de cobre (II) em solução sintética de concentração inicial 50 mg L^-1. Como os resultados foram satisfatórios para CA1, CA2 e CA3 (93,43, 97,23 e 96, 92 % para os respectivos carvões), decidiu-se pelo que apresentou maior percentual de remoção. O CA2 foi produzido e caracterizado quanto: às densidades reais e aparentes, à porosidade em leito fixo, ao pH, à umidade (em base úmida), às cinzas, ao carbono fixo e aos grupos funcionais pelo método de Boehm. Realizaram-se ensaios para determinar a eficiência de remoção de cobre (II) quanto à influência do diâmetro da partícula do carvão, ao pH da solução, à influência do tempo de contato e à variação da concentração inicial. Os resultados de maior percentual de remoção foram para o diâmetro 0,595≤D≤1,19mm, pH 5,09, tempo de 5 min e concentrações de 50, 100 e 150mg L^-1.O modelo cinético de adsorção que melhor se ajustou aos dados foi o de pseudo2^a ordem. Os dados experimentais apresentaram bom ajuste aos modelos matemáticos de isotermas de Langmuir e Frendlich. Sendo assim, obteve-se carvão ativado de baixo custo a partir da casca da castanha-do-Brasil a qual apresentou boa eficiência na remoção de cobre (II) (acima de 90 % para maioria das análises) possibilitando também a utilização no tratamento de efluentes.

Síntese e caracterização de óxido hidróxido de manganês do tipo manganita (γ -MnOOH)

Óxido hidróxido de manganês (γ - MnOOH) do tipo da manganita foi sintetizado por uma rota simples, em que a chave precursora K-birnessita foi preparada pelo método sol-gel. O tratamento hidrotermal da estrutura lamelar do tipo da birnessita favorece a obtenção de estruturas em túnel, sendo que o tamanho destes túneis depende das condições empregadas na síntese (pH, temperatura e tempo). A comprovação da formação de manganita sob as condições de síntese empregadas foi verificada pelas técnicas de difração de raios X, microscopia eletrônica de varredura, análises termogravimétrica e térmica diferencial e espectroscopia de infravermelho.

Síntese e caracterização de argila esmectita Zn-estevensita

Argila do grupo das esmectitas foi obtida com êxito em baixa temperatura de processamento por via hidrotérmica utilizando como precursores metassilicato de sódio, nitrato de zinco e uréia. Durante a etapa de síntese a composição molar da mistura reacional e a temperatura permaneceram constantes, variando-se o tempo de reação. As amostras sintetizadas foram caracterizadas por difração de raios X, microscopia eletrônica de varredura, espectroscopia de refletância difusa no infravermelho com transformada de Fourier, análise térmica diferencial e gravimétrica, análise de adsorção gasosa de nitrogênio pelo método BET e capacidade de troca de cátions. Os resultados evidenciam que com a metodologia empregada obtêm-se Zn-estevensita apresentando uma área superficial total na faixa de 171,6 a 203,4 m²/g e boa cristalinidade; sendo esta a única fase presente no produto sintetizado após reação estática a 90 ºC por um período de 44 a 138 h, indicando ser o aumento no tempo de síntese um parâmetro importante para o processo de cristalização da argila.

Degradação de poluentes orgânicos utilizando filmes de TiO2 modificados com íons prata

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)