Performance of spray nozzles in land applications with high speed

The aim of this study was to evaluate different spray nozzles for land applications in high speed on the coverage and deposit in soybean plants pulverization. It was evaluated the AXI 110 04 plane jet nozzles operated at speed of 4.17m.s-1 (control), the grey APE and the AXI 110 08 plane jets, and the TD HiSpeed 110 06 and AXI TWIN 120 06 twin jets, at speed of 9.72m.s-1. The application volume was fixed in 120L ha-1. The application efficiency was evaluated by two different methods: analysis of the coverage area using fluorescent pigment and UV light and analysis of deposits through the recovery and quantification of FD&C N°1 brilliant blue marker by spectrophotometry. Both analyses were done in samples collected from top, middle and bottom parts of the plants. The spray nozzles showed differences in coverage and deposit pattern, so in the top part, the coverage was increased with smaller drops and the deposits were increased with medium drops. In the other parts of the plants, there were no statistical differences between the treatments for both coverage and deposits. The displacement speed did not influence the application efficiency for nozzles with the same drop pattern, and the obtained spray coverage and deposits at the medium and bottom parts of the plants were less than 50% of that found at the top of the soybean plants.

A comparison of the performance and biological efficiency of new knapsack sprayers and a controlled droplet application (CDA) sprayer for the control of the diamondback moth, Plutella xylostella L. (Lepidoptera : Plutellidae)

Field trials and laboratory bioassays were undertaken to compare the performance and efficacy (mortality of diamondback moth larvae) of insecticides applied to cabbages with three high volume hydraulic knapsack sprayers (NS-16, PB-20 and Selecta 12V) and a controlled droplet application (CDA) sprayer. In field experiments, the high volume knapsack sprayers (application rate 500-600 L ha(-1)) provided better spray coverage on the upper and lower surfaces of inner leaves, the upper surfaces of middle and outer leaves, and greater biological efficacy than the CDA sprayer (application rate 20similar to40 L ha(-1)). The PB-20 provided better spray coverage on the upper surface of middle leaves and both surfaces of outer leaves when compared with the Selecta 12V. However, its biological efficacy in the field was not significantly different from that of the other high volume sprayers. Increasing the application rate from 20 to 40 L ha(-1) for the CDA sprayer significantly increased droplet density but had no impact on test insect mortality. Laboratory evaluations of biological efficacy yielded higher estimates than field evaluations and there was no significant difference between the performance of the PB-20 and the CDA sprayer. Significant positive relationships were detected between insect mortality and droplet density deposited for both the PB-20 and the CDA sprayers.

Adjuvantes e assistência de ar em pulverizador de barras sobre a deposição da calda e controle de Phakopsora pachyrhizi (Sydow & Sydow)

Com o intuito de melhorar a cobertura da pulverização e diminuir as perdas na produtividade da cultura da soja, o estudo objetivou avaliar o efeito da adição de adjuvantes à calda combinado ou não ao uso da assistência de ar sobre a deposição da pulverização, controle de Phakopsora pachyrhizi H. Sydow & P. Sydow, perdas de produção (peso de 1000 grãos) e produtividade da cultura (kg ha-1). Dois experimentos a campo foram conduzidos na cultura da soja, variedade Conquista, safra agrícola 2008/09. Um deles no delineamento em blocos ao acaso com três doses de adjuvantes associados a um marcador cúprico combinadas a dois níveis de ar na barra de pulverização (0 e 29 km h-1), totalizando 6 tratamentos e 4 repetições. Outro experimento foi instalado no mesmo local do anterior. O delineamento experimental utilizado foi o de blocos ao acaso com 7 tratamentos: fungicida e dois adjuvantes associados ao fungicida, combinados a dois níveis de ar na barra de pulverização (0 e 29 km h-1), mais testemunha, e 4 repetições. Após a pulverização do fungicida piraclostrobina + epoxiconazole com diferentes tecnologias, procedeu-se a avaliação da severidade da doença através da estimativa da área abaixo da curva de progresso da doença (AACPD) e da produtividade da cultura da soja. A assistência de ar na velocidade máxima gerada pelo ventilador (29 km h-1), combinada ao fungicida piraclostrobina + epoxiconazole mais o adjuvante organosiliconado Silwet L-77 contribuiu para melhor controle da ferrugem asiática, proporcionando incremento na produtividade e no peso de 1000 grãos.

Características da pulverização em citros em função do volume de calda aplicado com turbopulverizador

Este trabalho teve como objetivo avaliar o efeito do volume de calda aplicado por um turbopulverizador sobre a deposição e a cobertura em folhas, ramos e frutos de citros. A pulverização foi realizada com um pulverizador tratorizado Arbus 2000/Valência em pomar de laranja 'Natal', com porte médio de 4,0 m, sendo avaliados seis volumes de calda (50; 70; 85; 100; 150 e 200% do volume-padrão utilizado pelo produtor, de 28 L planta-1). Após a pulverização de plantas uniformes com calda contendo cobre e o traçador fluorescente Poliglow 830 YLSS, amostras foram coletadas em nove setores da planta, sendo a avaliação da deposição feita usando-se análise do íon cobre por espectrofotômetro de absorção atômica, e a da cobertura, por meio de imagens digitalizadas analisadas pelo programa para computador IDRISI. A análise estatística mostrou que, na avaliação da cobertura e deposição em citros, a utilização de frutos como estrutura de amostragem tendeu a evidenciar melhor o efeito dos tratamentos. Tanto a deposição quanto a cobertura tenderam a ser maiores nos setores frontal e saia da planta. Tanto a deposição quanto a cobertura não foram prejudicadas pela utilização do volume de 70% (19,6 L planta-1), indicando que tal volume pode substituir o volume de 100% (28 L planta-1) sem prejuízos ao controle de pragas.

Dispersion and evaporation of droplets amended with adjuvants on soybeans

Quantification of the effects of adjuvants on droplet behaviour on plant surfaces is needed to improve pesticide spray application efficiency for soybeans. Dispersion and evaporation of single 300-μm diameter droplets amended with each of four spray adjuvants at five concentrations were investigated for four soybean plant surfaces (abaxial and adaxial leaflet surfaces, petiole, basal stem). The four adjuvants were a crop oil concentrate (COC), a modified seed oil (MSO), a non-ionic surfactant (NIS) and an oil surfactant blend (OSB). A single-droplet generator was used to produce and deposit 300-μm diameter droplets on target surfaces under controlled environmental conditions. Adjuvants significantly increased the dispersion (or wetted area) of droplets on plant surfaces. Droplet-wetted areas increased with increased adjuvant concentrations but not in direct proportion. The average increases of wetted areas across the four soybean plant surfaces were 443, 462, 416, or 343% when the spray mixture was amended with COC, MSO, NIS or OSB at the manufacturer-recommended concentrations, respectively. Among the four surfaces, the largest wetted area was on the abaxial surface, followed by the adaxial surface, the petiole and then the basal stem. Droplet evaporation times were inversely proportional to the wetted areas. The evaporation time of 300-μm diameter droplets ranged from 36 to 142. s on the four surfaces when the spray mixture was amended with an adjuvant, whereas the water-only droplets ranged from 161 to 190. s. The results demonstrated that use of adjuvants offers great potential to improve the homogeneity of sprayed pesticides, to increase spray coverage and to reduce pesticide application rates on soybean plants. These effects could benefit farmers economically and reduce environmental contamination by pesticides. © 2012.

Pontas e velocidade de deslocamento na deposição de gotas da pulverização na cultura do algodão

Pós-graduação em Agronomia (Proteção de Plantas) - FCA

Sistemas de comutação de pontas na barra de pulverização para ajuste do tamanho de gotas às condiçoes climáticas e aplicação em taxas variáveis

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Caracterização da cobertura de pulverização necessária para controle do ácaro Brevipalpus phoenicis (G., 1939) em citrus

Pós-graduação em Agronomia (Produção Vegetal) - FCAV

Qualidade da pulverização em volume reduzido para o controle do bicho-mineiro Leucoptera coffeella (Guérin-Mèneville & Perrottet, 1842) (Lepidoptera: Lyonetiidae)

Pós-graduação em Agronomia (Entomologia Agrícola) - FCAV

Arranjo de semeadura da soja sobre o rendimento da cultura e da tecnologia de aplicação de produtos fitossanitários

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Dimensionless spray flux in wet granulation: Monte-Carlo simulations and experimental validation

Dimensionless spray flux Ψa is a dimensionless group that characterises the three most important variables in liquid dispersion: flowrate, drop size and powder flux through the spray zone. In this paper, the Poisson distribution was used to generate analytical solutions for the proportion of nuclei formed from single drops (fsingle) and the fraction of the powder surface covered by drops (fcovered) as a function of Ψa. Monte-Carlo simulations were performed to simulate the spray zone and investigate how Ψa, fsingle and fcovered are related. The Monte-Carlo data was an excellent match with analytical solutions of fcovered and fsingle as a function of Ψa. At low Ψa, the proportion of the surface covered by drops (fcovered) was equal to Ψa. As Ψa increases, drop overlap becomes more dominant and the powder surface coverage levels off. The proportion of nuclei formed from single drops (fsingle) falls exponentially with increasing Ψa. In the ranges covered, these results were independent of drop size, number of drops, drop size distribution (mono-sized, bimodal and trimodal distributions), and the uniformity of the spray. Experimental data of nuclei size distributions as a function of spray flux were fitted to the analytical solution for fsingle by defining a cutsize for single drop nuclei. The fitted cutsizes followed the spray drop sizes suggesting that the method is robust and that the cutsize does indicate the transition size between single drop and agglomerate nuclei. This demonstrates that the nuclei distribution is determined by the dimensionless spray flux and the fraction of drop controlled nuclei can be calculated analytically in advance.

Liquid distribution in wet granulation: dimensionless spray flux

This study investigates binder distribution in wet granulation and focuses on the nucleation zone, which is the area where the liquid binder and powder surface come into contact and form the initial nuclei. An equipment independent parameter, dimensionless spray flux Psi (a), is defined to characterise the most important process parameters in the nucleation process: solution flowrate, powder flux, and binder drop size. Ex-granulator experiments are used to study the relationship between dimensionless spray flux, process variables and the coverage of binder fluid on the powder surface. Lactose monohydrate powder on a variable speed riffler passed under a flat spray once only. Water and 7% HPC solution at two spray pressures were used as binders. Experiments with red dye and image analysis demonstrate that changes in dimensionless spray flux correlate with a measurable difference in powder surface coverage. Nucleation experiments show that spray flux controls the size and shape of the nuclei size distribution. At low Psi (a), the system operates in the drop controlled regime, where one drop forms one nucleus and the nuclei size distribution is narrow. At higher Psi (a), the powder surface cakes creating a broader size distribution. For controlled nucleation with the narrowest possible size distribution, it is recommended that the dimensionless spray flux be less than 0.1 to be in the drop-controlled regime. (C) 2001 Elsevier Science S.A. All rights reserved.

Spray coating technique asa surface treatment for woodcontaining paper grades

The objective of this work was to introduce the emerging non-contacting spray coating process and compare it to the existing coating techniques. Particular emphasis was given to the details of the spraying process of paper coating colour and the base paper requirements set by the new coating method. Spraying technology itself is nothing new, but the atomisation process of paper coating colour is quite unknown to the paper industry. The differences between the rheology of painting and coating colours make it very difficult to utilise the existing information from spray painting research. Based on the trials, some basic conclusion can be made:The results of this study suggest that the Brookfield viscosity of spray coating colour should be as low as possible, presently a 50 mPas level is regarded as an optimum. For the paper quality and coater runnability, the solids level should be as high as possible. However, the graininess of coated paper surface and the nozzle wear limits the maximum solids level to 60 % at the moment. Most likelydue to the low solids and low viscosity of the coating colour the low shear Brookfield viscosity correlates very well with the paper and spray fan qualities. High shear viscosity is also important, but yet less significant than the low shear viscosity. Droplet size should be minimized and besides keeping the brrokfield viscosity low that can be helped by using a surfactant or dispersing agent in the coating colour formula. Increasing the spraying pressure in the nozzle can also reduce the droplet size. The small droplet size also improves the coating coverage, since there is hardly any levelling taking place after the impact with the base paper. Because of the lack of shear forces after the application, the pigment particles do not orientate along the paper surface. Therefore the study indicates that based on the present know-how, no quality improvements can be obtained by the use of platy type of pigments. The other disadvantage of them is the rapid deterioration of the nozzle lifetime. Further research in both coating colour rheology and nozzle design may change this in the future, but so far only round shape pigments, like typically calcium carbonate is, can be used with spray coating. The low water retention characteristics of spray coating, enhanced by the low solids and low viscosity, challenge the base paper absorption properties.Filler level has to be low not to increase the number of small pores, which have a great influence on the absorption properties of the base paper. Hydrophobic sizing reduces this absorption and prevents binder migration efficiently. High surface roughness and especially poor formation of the base paper deteriorate thespray coated paper properties. However, pre-calendering of the base paper does not contribute anything to the finished paper quality, at least at the coating colour solids level below 60 %. When targeting a standard offset LWC grade, spraycoating produces similar quality to film coating, but yet blade coating being on a slightly better level. However, because of the savings in both investment and production costs, spray coating may have an excellent future ahead. The porousnature of the spray coated surface offers an optimum substrate for the coldset printing industry to utilise the potential of high quality papers in their business.

Evaluation of WC-17Co and WC-10Co-4Cr thermal spray coatings by HVOF on the fatigue and corrosion strength of AISI 4340 steel

It is known that chromium electroplating is related to the reduction in the fatigue strength of base metal. However, chromium results in protection against wear and corrosion combined with chemical resistance and good lubricity. Environmental requirements are an important point to be considered in the search for possible alternatives to hard chrome plating. Aircraft landing gear manufactures are considering WC thermal spray coating applied by the high-velocity oxygen-fuel (HVOF) process an alternative candidate, which shows performance at least comparable to results, obtained for hard chrome plating. The aim of this study is to compare the influence of WC-17Co and WC-10Co-4Cr coatings applied by HVOF process and hard chromium electroplating on the fatigue strength of AISI 4340 steel, with and without shot peening. S-N curves were obtained in axial fatigue test for base material, chromium plated and tungsten carbide coated specimens. Tungsten carbide thermal spray coating results in higher fatigue strength when compared to hard chromium electroplated. Shot peening prior to thermal spraying showed to be an excellent alternative to increase fatigue strength of AISI 4340 steel. Experimental data showed higher axial fatigue and corrosion resistance in salt fog exposure for samples WC-10Co-4Cr HVOF coated when compared with WC-17Co. Fracture surface analysis by scanning electron microscopy (SEM) indicated the existence of a uniform coverage of nearly all substrates. (C) 2004 Elsevier B.V. All rights reserved.

On The Distinct Molecular Architectures Of Dipping- And Spray-lbl Films Containing Lipid Vesicles.

The introduction of spraying procedures to fabricate layer-by-layer (LbL) films has brought new possibilities for the control of molecular architectures and for making the LbL technique compliant with industrial processes. In this study we show that significantly distinct architectures are produced for dipping and spray-LbL films of the same components, which included DODAB/DPPG vesicles. The films differed notably in their thickness and stratified nature. The electrical response of the two types of films to aqueous solutions containing erythrosin was also different. With multidimensional projections we showed that the impedance for the DODAB/DPPG spray-LbL film is more sensitive to changes in concentration, being therefore more promising as sensing units. Furthermore, with surface-enhanced Raman scattering (SERS) we could ascribe the high sensitivity of the LbL films to adsorption of erythrosin.