Pressure-Frequency Sensing Subxiphoid Access System for Use in Percutaneous Cardiac Electrophysiology: Prototype Design and Pilot Study Results

We have designed, built, and tested an early prototype of a novel subxiphoid access system intended to facilitate epicardial electrophysiology, but with possible applications elsewhere in the body. The present version of the system consists of a commercially available insertion needle, a miniature pressure sensor and interconnect tubing, read-out electronics to monitor the pressures measured during the access procedure, and a host computer with user-interface software. The nominal resolution of the system is <0.1 mmHg, and it has deviations from linearity of <1%. During a pilot series of human clinical studies with this system, as well as in an auxiliary study done with an independent method, we observed that the pericardial space contained pressure-frequency components related to both the heart rate and respiratory rate, while the thorax contained components related only to the respiratory rate, a previously unobserved finding that could facilitate access to the pericardial space. We present and discuss the design principles, details of construction, and performance characteristics of this system.

A zero-relative-velocity belt skimmer, Stage II : Confirming tests and prototype design /

Final report, issued May 1977.

Design of an Embedded Computer Board for Networking Applications

Tämä diplomityö tehtiin Convergens Oy:lle. Convergens on elektroniikan suunnittelutoimisto, joka on erikoistunut sulautettuihin järjestelmiin sekä tietoliikennetekniikkaan. Diplomityön tavoitteena oli suunnitella tietokonekortti tietoliikennesovelluksia varten asiakkaalle, jolta vaatimusmäärittelyt tulivat. Työ on rajattu koskemaan laitteen prototyypin suunnittelua. Työssä suunnitellaan pääasiassa WLAN-tukiaseman tietokone. Tukiasema onasennettavissa toimistoihin, varastoihin, kauppoihin sekä myös liikkuvaan ajoneuvoon. Suunnittelussa on otettu nämä asiat huomioon, ja laitteen akun pystyy lataamaan muun muassa auton akulla. Langattomat tekniikat ovat voimakkaasti yleistymässä, ja tämän työn tukiasema tarjoaakin varteenotettavan vaihtoehdon lukuisilla ominaisuuksillaan. Mukana on mm. GPS, Bluetooth sekä Ethernet-valmius. Langattomien tekniikoiden lisäksi myös sulautetut järjestelmät ovat voimakkaasti yleistymässä, ja nykyään mikroprosessoreita löytääkin lähesmistä vain. Tässä projektissa käytetty prosessori on nopeutensa puolesta kilpailukykyinen, ja siitä löytyy useita eri rajapintoja. Jatkossa tietokonekortille on myös tulossa WiMAX-tuki, joka lisää tukiaseman tulevaisuuden arvoa asiakkaalle. Projektiin valittu Freescalen MPC8321E-prosessori on PowerPC-arkkitehtuuriin perustuva ja juuri markkinoille ilmestynyt. Tämä toi mukanaan lisähaasteen, sillä kyseisestä prosessorista ei ollut vielä kaikkea tietoa saatavilla. Mekaniikka toi omat haasteensa mukanaan, sillä se rajoitti piirilevyn koonniin, että ylimääräistä piirilevytilaa ei juurikaan jäänyt. Tämän takia esimerkiksi DDR-muistit olivat haastavia reitittää, sillä muistivetojen on oltava melko samanpituisia keskenään. Käyttöjärjestelmänä projektissa käytetään Linuxia. Suunnittelu alkoi keväällä 2007 ja toimiva prototyyppi oli valmis alkusyksystä. Prototyypin testaus osoitti, että tietokonekortti kykenee täyttämään kaikki asiakkaan vaatimukset. Prototyypin testauksessa löytyneet viat ja optimoinnit on tarkoitus korjata tuotantomalliin, joten se antaa hyvän pohjan jatkosuunnittelua varten.

DFM(A)- aspects for a fixed electrical attenuator design

The goal of this paper is to describe a complete and extensive prototype design of a fixed electrical attenuator. The paper starts by describing the function and by giving some basic information about the attenuators. After a comprehensive description of the component, the facts of reverse engineering are discussed. The method itself is applied to ease manufacturing and design stages of this component. Information about materials and applied manufacturing technologies are also included in this report. By applying some specified DFMA-aspects the final design turned out to be a potential prototype device to be manufactured and for further analyse.

The systolic array genetic algorithm, an example of systolic arrays as a reconfigurable design methodology

We advocate the use of systolic design techniques to create custom hardware for Custom Computing Machines. We have developed a hardware genetic algorithm based on systolic arrays to illustrate the feasibility of the approach. The architecture is independent of the lengths of chromosomes used and can be scaled in size to accommodate different population sizes. An FPGA prototype design can process 16 million genes per second.

Design and evaluation of compound metformin/glipizide elementary osmotic pump tablets

A simple elementary osmotic pump (EOP) system that could deliver metformin hydrochloride (MT) and glipizide (GZ) simultaneously for extended periods of time was developed in order to reduce the problems associated with multidrug therapy of type 2 non-insulin-dependent diabetes mellitus. In general, both highly and poorly water-soluble drugs are not good candidates for elementary osmotic delivery. However, MT is a highly soluble drug with a high dose (500 mg) while GZ is a water-insoluble drug with a low dose (5 mg) so it is a great challenge to pharmacists to provide satisfactory extended release of MT and GZ. In this paper sodium carbonate was used to modulate the solubility of GZ within the core and MT was not only one of the active ingredients but also the osmotic agent. The optimal EOP was found to deliver both drugs at a rate of approximately zero order for up to 10 h in pH 6.8, independent of environment media. In-vivo evaluation was performed relative to the equivalent dose of conventional MT tablet and GZ tablet by a cross-study in six Beagle dogs. The EOP had a good sustained effect in comparison with the conventional product. The prototype design of the system could be applied to other combinations of drugs used for cardiovascular diseases, diabetes, etc.

Design of a Novel Auto-Rotating UAV Platform for Underground Mine Cavity Surveying

The purpose of this paper is to investigate the potential for use of UAVs in underground mines and present a prototype design for a novel autorotating UAV platform for underground 3D data collection.

Mechatronic system for ABO human blood typing

In medical emergency situations, when a patient needs a blood transfusion, the universal blood type O− is administered. This procedure may lead to the depletion of stock reserves of O− blood. Nowadays, there is no commercial equipment capable of determining the patient's blood type in situ, in a fast and reliable process. Human blood typing is usually performed through the manual test, which involves a macroscopic observation and interpretation of the results by an analyst. This test, despite of having a fast response time, may lead to human errors, which sometimes can be fatal to the patient. This paper presents the development of an automatic mechatronic prototype for determining human blood typing (ABO and Rh systems) through image processing techniques. The prototype design takes into account the characteristics of reliability of analysis, portability, and response time allowing the system to be used in emergency situations. The developed prototype performs blood and reagents mixture acquires the resultant image and processes the data (based on image processing techniques) to determine the sample blood type. It was tested in a laboratory, using cataloged samples of blood types, provided by the Portuguese Institute of Blood and Transplantation. Hereafter, it is expected to test and validate the prototype in clinical environments.

Pyörivän keskiökärjen rakenteen kehittäminen työstövärähtelyjen välttämiseksi sorvauksessa

Tässä diplomityössä käsitellään sorvauksen työstövärähtelyjen ja sorvin keskiökärjen rakenteen yhteyttä. Työ on osa Lappeenrannan teknillisen yliopiston VMAX-projektia, ja sen taustalla on pyrkimys uudenlaisen, sorvin kärkipylkän puristusvoiman ajonaikaiseen säätämiseen perustuvan työstövärähtelyjen välttämismenetelmän kehittämiseen. Tämän menetelmän toiminnan todentaminen oli työn ensimmäinen tavoite. Menetelmän toteuttaminen asettaa kuitenkin käytetyn keskiökärjen rakenteelle tiettyjä vaatimuksia. Työn toisena tavoitteena oli nämä vaatimukset täyttävän keskiökärjen prototyypin kehittäminen. Tutkimus eteni seuraavasti. Ensimmäiseksi ongelma määriteltiin tutustumalla työn teoreettiseen taustaan ja aiheeseen liittyvään tutkimukseen Lappeenrannan teknillisestä yliopistosta ja muualta. Myös keskiökärkiä valmistavien yritysten tuotekatalogeja tarkasteltiin. Seuraavaksi siirryttiin alustavaan suunnitteluvaiheeseen, jossa verifioitiin menetelmän toiminta ja luotiin konsepteja keskiökärjen rakenteen kehittämistä varten. Tämän alustavan vaiheen jälkeen suoritettiin suunnitteluprosessi keskiökärjen prototyypille. Lopuksi, suunnitellun prototyypin rakenteen käyttäytymistä arvioitiin tietokonemallinnuksen avulla. Lisätuloksena tutkimuksen aikana johdettiin yksinkertaistettu elementtimenetelmään perustuva laskentamalli järjestelmän ominaistaajuuksien selvittämiseksi. Laskentamallin tarkkuutta arvoitiin. Suunnitteluprosessin tuloksena saatiin kaikki menetelmän toiminnan sekä normaalin käytön asettamat vaatimukset täyttävä rakenne keskiökärjen prototyypille. Myös johdetun laskentamallin tulokset ovat varsin lähellä 3D-elementtimallinnuksen antamia tuloksia. Tutkimuksen tavoitteiden voidaan siis sanoa toteutuneen. Koska prototyyppiä ja laskentamallia ei kuitenkaan ole vielä kokeellisesti verifioitu, tämä ei ole täysin varmaa.

A sodar for profiling in a spatially inhomogeneous urban environment

The urban boundary layer, above the canopy, is still poorly understood. One of the challenges is obtaining data by sampling more than a few meters above the rooftops, given the spatial and temporal inhomogeneities in both horizontal and vertical. Sodars are generally useful tools for ground-based remote sensing of winds and turbulence, but rely on horizontal homogeneity (as do lidars) in building up 3-component wind vectors from sampling three or more spatially separated volumes. The time taken for sound to travel to a typical range of 200 m and back is also a limitation. A sodar of radically different design is investigated, aimed at addressing these problems. It has a single vertical transmitted sound pulse. Doppler shifted signals are received from a number of volumes around the periphery of the transmitted beam with microphones which each having tight angular sensitivity at zenith angles slightly off-vertical. The spatial spread of sampled volumes is therefore smaller. By having more receiver microphones than a conventional sodar, the effect of smaller zenith angle is offset. More rapid profiling is also possible with a single vertical transmitted beam, instead of the usual multiple beams.A prototype design is described, together with initial field measurements. It is found that the beam forming using a single dish antenna and the drift of the sound pulse downwind both give rise to reduced performance compared with expectations. It is concluded that, while the new sodar works in principle, the compromises arising in the design mean that the expected advantages have not been realized

Facilitating Locking Pin Alignment in Transtibial Amputees via Auto-Retracting Tethered Pin

Thesis (Master's)--University of Washington, 2016-06

C-MEMS Based Micro Enzymatic Biofuel Cells

Miniaturized, self-sufficient bioelectronics powered by unconventional micropower may lead to a new generation of implantable, wireless, minimally invasive medical devices, such as pacemakers, defibrillators, drug-delivering pumps, sensor transmitters, and neurostimulators. Studies have shown that micro-enzymatic biofuel cells (EBFCs) are among the most intuitive candidates for in vivo micropower. In the fisrt part of this thesis, the prototype design of an EBFC chip, having 3D intedigitated microelectrode arrays was proposed to obtain an optimum design of 3D microelectrode arrays for carbon microelectromechanical systems (C-MEMS) based EBFCs. A detailed modeling solving partial differential equations (PDEs) by finite element techniques has been developed on the effect of 1) dimensions of microelectrodes, 2) spatial arrangement of 3D microelectrode arrays, 3) geometry of microelectrode on the EBFC performance based on COMSOL Multiphysics. In the second part of this thesis, in order to investigate the performance of an EBFC, behavior of an EBFC chip performance inside an artery has been studied. COMSOL Multiphysics software has also been applied to analyze mass transport for different orientations of an EBFC chip inside a blood artery. Two orientations: horizontal position (HP) and vertical position (VP) have been analyzed. The third part of this thesis has been focused on experimental work towards high performance EBFC. This work has integrated graphene/enzyme onto three-dimensional (3D) micropillar arrays in order to obtain efficient enzyme immobilization, enhanced enzyme loading and facilitate direct electron transfer. The developed 3D graphene/enzyme network based EBFC generated a maximum power density of 136.3 μWcm-2 at 0.59 V, which is almost 7 times of the maximum power density of the bare 3D carbon micropillar arrays based EBFC. To further improve the EBFC performance, reduced graphene oxide (rGO)/carbon nanotubes (CNTs) has been integrated onto 3D mciropillar arrays to further increase EBFC performance in the fourth part of this thesisThe developed rGO/CNTs based EBFC generated twice the maximum power density of rGO based EBFC. Through a comparison of experimental and theoretical results, the cell performance efficiency is noted to be 67%.

User-centered design of the interface prototype of a business intelligence mobile application

Dissertação para obtenção do Grau de Mestre em Engenharia e Gestão Industrial

A design and a prototype for a mobile information service for tourists

Tourism is one of the biggest industry branches with billions of tourists traveling every year around the world. Therefore, solutions providing tourist information have to be up to date with both changes in the industry and the world’s technological progress. The aim of this thesis is to present a design and a prototype of a tourist mobile service which is individual-oriented, cost-free for the end user, and secure. On the information providers’ side, the solution is implemented as a Webbased database. The end users access the information through a Bluetooth application on their mobile devices. The Bluetooth-based solution allows to avoid any costs for the end users, that is tourists. The study shows that, even with small data transfers, the tourists could save significantly when compared to possible roaming charges for data transfer. Also, the proposed mobile service is not intrusive, as it is provided through an application installed by tourists voluntarily on their mobile devices. Through design and implementation this work shows that it is possible to build a system which can be used to provide information services to tourists through mobile phones. The work achieved a successful ongoing synchronization between the client and the server databases. Implementation and usage were limited to smart phones only, as they provide better technological support for the solution having features like maps, GPS, Wi-Fi, Bluetooth and Databases. Moreover, the design of this system shows how Bluetooth technology can be used effectively as a means of communication while minimizing its shortcomings and risks, such as security, by bypassing Bluetooth server service discovery protocol (SDP) and connecting directly to the device. Apart from showing the design and implementation of the end-user costfree mobile information service, the results of this work also highlight the possible business opportunities to the provider of the service.

Design and Development of a Performance Evaluation Prototype for IT Organizations in the Context of Outsourcing

The present study shows design and development of a performance evaluation prototype for IT organizations in the context of outsourcing. The main objective of this research is to help an IT organization in the context of outsourcing to realize its current standing, so it can take corrective steps where ever necessary and strive for continuous improvement. Service level management (SLM) process plays a crucial role in controlling the quality provision for IT service. Out sourcing is the process of entrusting the responsibility of providing certain goods and services to an external party. We have tried to identify as many as twenty complexities and categorized in to four headings. Complexities associated with contracts and SLAs,SLM process,SLM organization and complexities due to intrinsic characteristics. In this study it is possible to measure the quality of the performance of an IT organization in an outsourcing environment effectively