Polyacrylic acid polymers hydrogels intended to topical drug delivery: preparation and characterization

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Physicochemical characterization of bioactive polyacrylic acid organogels as potential antimicrobial implants for the buccal cavity

This study describes the formulation and physicochemical characterization of poly(acrylic acid) (PAA) organogels, designed as bioactive implants for improved treatment of infectious diseases of the oral cavity. Organogels were formulated containing a range of concentrations of PAA (3-10% w/w) and metronidazole (2 or 5% w/w, representing a model antimicrobial agent) in different nonaqueous solvents, namely, glycerol (Gly), polyethylene glycol (PEG 400), or propylene glycol (PG). Characterization of the organogels was performed using flow rheometry, compressional analysis, oscillatory rheometry, in vitro mucoadhesion, moisture uptake, and drug release, methods that provide information pertaining to the nonclinical and clinical use of these systems. Increasing the concentration of PAA significantly increased the consistency, compressibility, storage modulus, loss modulus, dynamic viscosity, mucoadhesion, and the rate of drug release. These observations may be accredited to enhanced molecular polymer entanglement. In addition, the choice of solvent directly affected the physicochemical parameters of the organogels, with noticeable differences observed between the three solvents examined. These differences were accredited to the nature of the interaction of PAA with each solvent and, importantly, the density of the resultant physical cross-links. Good correlation was observed between the viscoelastic properties and drug release, with the exception of glycerol-based formulations containing 5 and 10% w/w PAA. This disparity was due to excessive swelling during the dissolution analysis. Ideally, formulations should exhibit controlled drug release, high viscoelasticity, and mucoadhesion, but should flow under minimal stresses. Based on these criteria, PEG 400-based organogels composed of 5% or 10% w/w PAA exhibited suitable physicochemical properties and are suggested to be a potentially interesting strategy for use as bioactive implants designed for use in the oral cavity. © 2008 American Chemical Society.

Polyacrylic Acid Assisted Synthesis of Cu2ZnSnS4 by Hydrothermal Method

Pure phase Cu2ZnSnS4 (CZTS) nanoparticles were successfully synthesized via polyacrylic acid (PAA) assisted one-pot hydrothermal route. The morphology, crystal structure, composition and optical properties as well as the photoactivity of the as-synthesized CZTS nanoparticles were characterized by X-ray diffraction, Raman spectroscopy, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectrometer, UV-visible absorption spectroscopy and photoelectrochemical measurement. The influence of various synthetic conditions, such as the reaction temperature, reaction duration and the amount of PAA in the precursor solution on the formation of CZTS compound was systematically investigated. The results have shown that the crystal phase, morphology and particle size of CZTS can be tailored by controlling the reaction conditions. The formation mechanism of CZTS in the hydrothermal reaction has been proposed based on the investigation of time-dependent phase evolution of CZTS which showed that metal sulfides (e.g., Cu2S, SnS2 and ZnS) were formed firstly during the hydrothermal reaction before forming CZTS compound through nucleation. The band gap of the as-synthesized CZTS nanoparticles is 1.49 eV. The thin film electrode based on the synthesized CZTS nanoparticles in a three-electrode photoelectrochemical cell generated pronounced photocurrent under illumination provided by a red light-emitting diode (LED, 627 nm), indicating the photoactivity of the semiconductor material.

A method of synthesis of silicious inorganic ordered materials (MCM-41-SBA-1) employing polyacrylic acid-C(n)TAB-TEOS nanoassemblies

In this work we describe the synthesis of a variety of MCM-41 type hexagonal and SBA-1 type cubic mesostructures and mesoporous silicious materials employing a novel synthesis concept based on polyacrylic acid (Pac)-C(n)TAB complexes as backbones of the developing structures. The ordered porosity of the solids was established by XRD and TEM techniques. The synthesis concept makes use of Pac-C(n)TAB nanoassemblies as a preformed scaffold, formed by the gradual increase of pH. On this starting matrix the inorganic precursor species SiO2 precipitate via hydrolysis of TEOS under the influence of increasing pH. The molecular weight (MW) of Pac, as well as the length of carbon chain in C,TAB, determine the physical and structural characteristics of the obtained materials. Longer chain surfactants (C(16)TAB) lead to the formation of hexagonal phase, while shorter chain surfactants (C(14)TAB, C(12)TAB) favor the SBA-1 phase. Lower MW of Pac (approximate to2000) leads to better-organized structures compared to higher MW ( 450,000), which leads to worm-like mesostructures. Cell parameters and pore size increase with increasing polyelectrolyte and/or surfactant chain, while at the same time SEM photography reveals that the particle size decreases. Conductivity experiments provide some insight into the proposed self-assembling pathway. (C) 2003 Elsevier Inc. All rights reserved.

Rheological, mechanical, and bioadhesive behavior of hydrogels to optimize skin delivery systems

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Preparation of polymer/silica nanoscale hybrids through sol-gel method involving emulsion polymers. II. Poly(ethyl acrylate)/SiO2

Poly(ethyl acrylate) (PEA)/SiO2 hybrids with different compositions were prepared under different casting temperatures and pH values. Their morphology as investigated by transmission electron microscopy (TEM) shows that samples with different compositions have different morphologies. When the SiO2 content is lower, PEA is the continuous phase and SiO2 is the dispersed phase. At higher SiO2 content, the change in phase morphology takes place, nd PEA gradually dispersing in the form of latex particles in SiO2 matrix. Change in phase morphology depends mainly on the time the sol-gel transition occurs. At suitable casting temperature and pH value, PEA/SiO2 in 95/5 and 50/50 hybrids with even dispersion was obtained.

Methylene Blue Doped Polymers: efficient Media for Optical Recording

Polymer materials find application in optical storage technology, namely in the development of high information density and fast access type memories. A new polymer blend of methylene blue sensitized polyvinyl alcohol (PVA) and polyacrylic acid (PAA) in methanol is prepared and characterized and its comparison with methylene blue sensitized PVA in methanol and complexed methylene blue sensitized polyvinyl chloride (CMBPVC) is presented. The optical absorption spectra of the thin films of these polymers showed a strong and broad absorption region at 670-650 nm, matching the wavelength of the laser used. A very slow recovery of the dye on irradiation was observed when a 7:3 blend of polyvinyl alcohol/polyacrylic acid at a pHof 3.8 and a sensitizer concentration of 4.67 10 5 g/ml were used. A diffraction efficiency of up to 20% was observed for the MBPVA/alcohol system and an energetic sensitivity of 2000 mJ/cm2 was obtained in the photosensitive films with a spatial frequency of 588 lines/mm.

Methylene Blue Doped Polymers:Efficient Media for Optical Recording

Polymer materials find application in optical storage technology, namely in the development of high information density and fast access type memories. A new polymer blend of methylene blue sensitized polyvinyl alcohol (PVA) and polyacrylic acid (PAA) in methanol is prepared and characterized and its comparison with methylene blue sensitized PVA in methanol and complexed methylene blue sensitized polyvinyl chloride (CMBPVC) is presented. The optical absorption spectra of the thin films of these polymers showed a strong and broad absorption region at 670-650 nm, matching the wavelength of the laser used. A very slow recovery of the dye on irradiation was observed when a 7:3 blend of polyvinyl alcohol/polyacrylic acid at a pHof 3.8 and a sensitizer concentration of 4.67 10 5 g/ml were used. A diffraction efficiency of up to 20% was observed for the MBPVA/alcohol system and an energetic sensitivity of 2000 mJ/cm2 was obtained in the photosensitive films with a spatial frequency of 588 lines/mm.

Synthesis of novel functional polyolefin containing carboxylic acid via Friedel-Crafts acylation reaction

The strong polar group, carboxylic acid, has triumphantly been introduced into ethylene and allylbenzene copolymers without obvious degradation or crosslinking via Friedel-Crafts (F-C) acylation reaction with glutaric anhydride (GA), succinic anhydride (SA) and phthalic anhydride (PA) in the presence of anhydrous aluminum chloride in carbon disulfide. Some important reaction parameters were examined in order to optimize the acylation process. In the optimum reaction conditions, almost all of the phenyls can be acylated with any anhydride. The microstructure of acylated copolymer was characterized by Fr-IR, H-1 NMR and H-1-H-1 COSY. All the peaks of acylated copolymers can be accurately attributed, which indicates that all the acylation reactions occur only at the para-positions of the substituent of the aromatic rings. The thermal behavior was studied by differential scanning calorimetry (DSC), showing that the melting temperatures (T(m)s) of acylated copolymers with GA firstly decrease slowly and then increase significantly with the increase of the amount of carboxyl acid groups.

An examination of the rheological and mucoadhesive properties of poly(Acrylic acid) organogels designed as platforms for local drug delivery to the oral cavity

This study examined the rheological/mucoadhesive properties of poly (acrylic acid) PAA organogels as platforms for drug delivery to the oral cavity. Organogels were prepared using PAA (3%, 5%, 10% w/w) dissolved in ethylene glycol (EG), propylene glycol (PG), 1,3-propylene glycol (1,3-PG), 1,5-propanediol (1,5-PD), polyethylene glycol 400 (PEG 400), or glycerol. All organogels exhibited pseudoplastic flow. The increase in storage (G') and loss (G '') moduli of organogels as a function of frequency was minimal, G '' was greater than G '' (at all frequencies), and the loss tangent <1, indicative of gel behavior. Organogels prepared using EG, PG, and 1,3-propanediol (1,3-PD) exhibited similar flow/viscoelastic properties. Enhanced rheological structuring was associated with organogels prepared using glycerol (in particular) and PEG 400 due to their interaction with adjacent carboxylic acid groups on each chain and on adjacent chains. All organogels (with the exception of 1,5-PD) exhibited greater network structure than aqueous PAA gels. Organogel mucoadhesion increased with polymer concentration. Greatest mucoadhesion was associated with glycerol-based formulations, whereas aqueous PAA gels exhibited the lowest mucoadhesion. The enhanced network structure and the excellent mucoadhesive properties of these organogels, both of which may be engineered through choice of polymer concentration/solvent type, may be clinically useful for the delivery of drugs to the oral cavity.

Fabrication and Characterization of Methylene-Blue-Doped Polyvinyl Alcohol–Polyacrylic Acid Blend for Holographic Recording

A methylene-blue-sensitized polymer blend of polyvinyl alcohol and polyacrylic acid is fabricated and tested for holographic recording. It was found to have good characteristics such as high sensitivity, storage stability, ease of fabrication, and environmental stability. Optimization of the ratio of polyvinyl alcohol polyacrylic acid, the sensitizer concentration, pH, energy, diffraction efficiency measurements, etc., have been done. pH is found to have a great influence on the recovery of the dye in this matrix. The results of experimental investigations into the properties of this new material are reported.

Surface Functionalization of Monodisperse Magnetic Nanoparticles

We present a systematic methodology to functionalize magnetic nanoparticles through surface-initiated atom-transfer radical polymerization (ATRP). The magnetite nanoparticles are prepared according to the method proposed by Sun et al. (2004), which leads to a monodisperse population of ~ 6 nm particles stabilized by oleic acid. The functionalization of the nanoparticles has been performed by transforming particles into macro-initiators for the ATRP, and to achieve this two different routes have been explored. The first one is the ligand-exchange method, which consists of replacing some oleic acid molecules adsorbed on the particle surface with molecules that act as an initiator for ATRP. The second method consists in using the addition reaction of bromine to the oleic acid double bond, which turns the oleic acid itself into an initiator for the ATRP. We have then grown polymer brushes of a variety of acrylic polymers on the particles, including polyisopropylacrylamide and polyacrylic acid. The nanoparticles so functionalized are water soluble and show responsive behavior: either temperature responsive behavior when polyisopropylacrylamide is grown from the surface or PH responsive in the case of polyacrylic acid. This methodology has potential applications in the control of clustering of magnetic nanoparticles.

Probing the receptor interactions ofan H5 avian influenza virus using a baculovirus expression system and functionalised poly(acrylic acid) ligands

Influenza viruses attach to host cells by binding to terminal sialic acid (Neu5Ac) on glycoproteins or glycolipids. Both the linkage of Neu5Ac and the identity of other carbohydrates within the oligosaccharide are thought to play roles in restricting the host range of the virus. In this study, the receptor specificity of an H5 avian influenza virus haemagglutinin protein that has recently infected man (influenza strain A/Vietnam/1194/04) has been probed using carbohydrate functionalised poly(acrylic acid) polymers. A baculovirus expression system that allows facile and safe analysis of the Neu5Ac binding specificity of mutants of H5 HA engineered at sites that are predicted to effect a switch in host range has also been developed. (C) 2007 Elsevier Ltd. All rights reserved.

Probing the receptor interactions of an H5 avian influenza virus using a baculovirus expression system and functionalised poly(acrylic acid) ligands

Influenza viruses attach to host cells by binding to terminal sialic acid (Neu5Ac) on glycoproteins or glycolipids. Both the linkage of Neu5Ac and the identity of other carbohydrates within the oligosaccharide are thought to play roles in restricting the host range of the virus. In this study, the receptor specificity of an H5 avian influenza virus haemagglutinin protein that has recently infected man (influenza strain A/Vietnam/1194/04) has been probed using carbohydrate functionalised poly(acrylic acid) polymers. A baculovirus expression system that allows facile and safe analysis of the Neu5Ac binding specificity of mutants of H5 HA engineered at sites that are predicted to effect a switch in host range has also been developed. (C) 2007 Elsevier Ltd. All rights reserved.

Polymerisierbare und polymere Langmuir-Blodgett-Monoschichten zur gezielten Kalziumcarbonatkristallisation an der Luft-Wasser-Grenzfläche

In der vorliegenden Arbeit konnte mit Hilfe von neu synthetisierten Monomeren und Polymeren Kristallisationstemplate für die Kalziumkarbonatkristallisation dargestellt werden. Hierzu wurde zunächst die Phasenseparation des Monomeren und Polymeren mit der nukleationsfördernden Stearinsäure detailliert untersucht und gezeigt, dass die Monomer und Polymer-Mischsysteme auf Ca(HCO3)2-Lsg. perfekt phasenseparieren. Weiter konnte diese entmischte Struktur mit Hilfe von UV-Bestrahlung in der Monoschicht polymerisiert und damit fixiert werden. Des weiteren konnte gezeigt werden, dass die Kristallisation unter den monomeren und polymeren Bereichen vollständig inhibiert wird und ausschließlich unter den Stearinsäuredomänen von statten geht. Das Problem der Kristallisation in die dritte Dimension, also ins Volumen, konnte durch die Zugabe von Polyacrylsäure zur Subphase kontrolliert werden, so dass nun eine Abbildung der strukturierten Monoschicht durch Kalkkristallisation möglich ist. Im zweiten Teil der Arbeit konnte ein amphiphiles Itaconat synthetisiert werden, welches auf Grund seiner Carbonsäurefunktion ebenfalls nukleationsfördernd wirkt. Auch hier war es möglich die Monoschicht zu polymerisieren. Weiter konnte erneut gezeigt werden, dass es möglich ist mit Hilfe von Polyacrylsäurezusatz die interne Struktur der Membran als Templat für die Kristallisation zu nutzen, so dass auch dieses System zur gezielten Kalkkristallisation genutzt werden kann.