Structural control of photoluminescence of four poly(urethane-urea-co-1,3,5-triazine)s: Synthesis and characterization

A series of segmented poly(urethane-urea)s containing 1,3,5 triazine in the hard block and hexamethylene spacers in the soft block was prepared. The hard to soft segment ratio was varied systematically, to afford a series of polymers in which the chromophore concentration varied from 4.2% to 18.1%. Although triazine emission is located in the UV region, the films with higher content of the chromophore emitted a visible blue light (425 nm) when excited at the very red-edge of the absorption band. The photophysical properties of the materials were strongly dependent on the relative amount of triazine moieties along the main chain. Isolated moieties emit in copolymers with small amount of triazine groups, indicating that even though in solid state, these moieties tend to be apart. Two photophysical consequences were observed when the amount of triazine increases: there is some energy transfer process involving isolated moieties with consequent decrease of the lifetime and an additional red-edge emission attributed to aggregated lumophores. The mono-exponential decay observed for the isolated form is substituted by a bi-exponential decay of the aggregated species. The materials were not strong emitters, but since the N-containing triazine moieties are good electron transport groups, the polymers have potential application as electron transport enhancers in various applications. © 2006 Elsevier B.V. All rights reserved.

Caracterização de filmes formados por dispersões aquosas de poli(uretano-uréia)s para aplicação em membranas para permeação de gases

Entre os polímeros considerados promissores para a remoção seletiva de CO2, destacam-se aqueles que contêm os grupos glicol etilênico (EG). Nesta dissertação, foram obtidos filmes a partir de dispersões aquosas de poliuretano (PU), sintetizadas em trabalho anterior, à base de poli(glicol propilênico) (PPG), copolímero em bloco à base de poli(glicol etilênico) (PEG) e PPG (EG-b-PG), ácido dimetilolpropiônico (DMPA), diisocianato de isoforona (IPDI) e etilenodiamina (EDA). PPG, EG-b-PG e DMPA formaram as regiões flexíveis nas proporções de: PPG 100% e 0% EG-b-PG, PPG 75% e 25% EG-b-PG, PPG 50% e 50% EG-b-PG e PPG 25% e 75% EG-b-PG em termos de equivalentes-gramas. A influência da quantidade dos segmentos de PEG foi avaliada por ensaios de permeação com os gases CO2, CH4 e N2. Os filmes obtidos das dispersões foram caracterizados por espectrometria de infravermelho com transformadas de Fourier (FTIR), análise termogravimétrica (TGA), difração de raios x (DRX) e espalhamento de raios X a baixo ângulo (SAXS). Espectros de FTIR mostraram que os segmentos de EG influenciaram a frequência da banda de carbonila. Curvas de perda de massa (TG) mostraram perfis semelhantes de degradação, enquanto que as curvas derivadas apresentaram diferenças. DRX e SAXS mostraram que os segmentos de PEG promoveram uma maior ordenação na estrutura da membrana. Testes de permeação de gases mostraram que o aumento do teor de PEG aumentou o valor da permeabilidade para o CO2, indicando que os segmentos de PEG interagiram favoravelmente com este gás. Em relação ao CH4 e N2, houve uma diminuição na permeabilidade quando comparados com os valores encontrados para o CO2, sendo atribuído a perda de mobilidade segmental. Em termos de seletividade, para o par CO2/CH4 foi obtido um valor médio de 61,7 para a membrana contendo o maior teor de PEG, e o par CO2/N2 um valor médio de 121,5, sendo superior aos valores encontrados na literatura, tornando o material promissor

Estudo do efeito da adição de poli(glicol etilênico-b-glicol propilênico) na formação de dispersões aquosas poliuretânicas à base de poli(glicol propilênico)

Foram produzidas dispersões aquosas não-poluentes e inovadoras de poli(uretano-uréia) à base de poli(glicol propilênico) (PPG) e de copolímeros em bloco, poli(glicol etilênicob-glicol propilênico), (EG-b-PG) com teor de 7% de unidades de glicol etilênico. Os poli(uretano-uréia)s foram preparados, em duas etapas, pelo método do prepolímero. Na primeira etapa, foram obtidos anionômeros, sintetizados em massa, à base do copolímero EG-bPG, PPG, ácido dimetilol propiônico (DMPA) (gerador dos sítios aniônicos) e diisocianato de isoforona (IPDI). Ainda na primeira etapa, os grupos carboxílicos do DMPA foram submetidos à neutralização com trietilamina (TEA). Na segunda etapa, foi realizada a dispersão do prepolímero anionômero e, em seguida, foi conduzida a reação de extensão de cadeia com a hidrazina (HYD). Nas diferentes formulações, foram variadas a razão NCO/OH e as proporções de PPG e do copolímero em bloco EG-b-PG. Além disso, foram obtidas dispersões aquosas programadas para teores de sólidos de 40 e 50%. As dispersões foram avaliadas quanto ao teor de sólidos totais, tamanho médio de partícula e viscosidade. Os filmes, obtidos por vazamento das dispersões, foram avaliados quanto à absorção de água, termogravimetria (TG) e propriedades mecânicas (ensaio de tração). Os filmes vazados e os monômeros foram caracterizados por espectrometria na região de infravermelho (FTIR) As dispersões obtidas se mostraram adequadas para serem aplicadas como revestimento para madeira, metais e vidro

Síntese e caracterização de filmes de nanopartículas de prata dispersas em poli(uretano-ureia) para separação de gases petroquímicos

A utilização de novos materiais aplicados aos processos de separação por membranas tem sido objeto de constante pesquisa acadêmica e tecnológica. Na permeação de gases petroquímicos, a modificação de estruturas poliméricas e o uso de membranas de transporte facilitado por adição de sais contendo metais ou nanopartículas destacam-se dentre as opções disponíveis. Os objetivos deste trabalho foram avaliar alterações químicas, estruturais e térmicas na matriz polimérica de poli(uretano-ureia) (PUU) provocadas pela adição de nanopartículas de prata (AgNps) e obter dados de pemeabilidade de gases petroquímicos (C2H4, C2H6, CO2 e N2) para avaliar a influência das AgNps no transporte desses gases através do filme polimérico. Alterações nos espectros de FTIR nas bandas de estiramento das ligações C-O-C e C=O (uretânica e ureica), e deslocamentos nos picos de difração, demonstram que houve interação entre as AgNps e o oxigênio éter do PUU. A interação com as AgNps diminuiu a estabilidade térmica dos domínios flexíveis do polímero, região onde são encontrados os grupos éteres. As imagens de TEM mostraram que houve baixa dispersão das Nps na matriz polimérica. A interação das AgNps com o grupo éter diminuiu a permeabilidade de todos os gases, porém a redução da permeabilidade do CO2 e do C2H4 foi muito mais significativa, mostrando a interferência das AgNps na sorção desses dois gases. O transporte facilitado de olefinas através dos filmes poliméricos não foi observado, em parte, causado pela baixa dispersão das AgNps na matriz polimérica. Apesar da interação, não foi possível responder se a superfície das Nps estava ativada para o transporte facilitado. Contudo, através dos resultados do trabalho foi possível propor um mecanismo de interação entre as AgNps e o PUU, e verificar como a presença das Nps pode alterar a interação da matriz polimérica com gases petroquímicos

Hydrogen bonded supramolecular elastomers : correlating hydrogen bonding strength with morphology and rheology

A series of six low molecular weight elastomers with hydrogen bonding end-groups have been designed, synthesised and studied. The poly(urethane) based elastomers all contained essentially the same hard block content (ca. 11%) and differ only in the nature of their end-groups. Solution state 1H NMR spectroscopic analysis of model compounds featuring the end-groups demonstrate that they all exhibit very low binding constants, in the range 1.4 to 45.0 M-1 in CDCl3, yet the corresponding elastomers each possess a markedly different nanoscale morphology and rheology in the bulk. We are able to correlate small variations of the binding constant of the end-groups with dramatic changes in the bulk properties of the elastomers. These results provide an important insight into the way in which weak non-covalent interactions can be utilized to afford a range of self-assembled polyurethane based materials that feature different morphologies.

Nicht-wässrige Emulsionen zur Erzeugung neuer Nanopartikel

In der eingereichten Arbeit wurde die Nutzung von nicht-wässrigen Emulsionen, bestehend aus zwei organischen, aprotischen Lösungsmitteln, zur Erzeugung verschiedener polymerer Nanopartikel beschrieben. Diese Zweiphasenmischungen und die Verwendung maßgeschneiderter Emulgatoren bestehend aus Poly(isopren-block-methylmethacrylat) ermöglichten den Zugang zu einer Vielzahl an Reaktionen und Prozessen, welche in wässrigen Emulsionen bisher nicht oder nur schwer möglich waren. Die Generierung von Partikeln auf Basis katalytischer Polymerisationen erfolgte unter Verwendung der Ringöffnenden Metathese-Polymerisation (ROMP), der Acyclischen Dien-Metathese-Polymerisation (ADMET), der Cyclopolymerisation von α,ω-Diinen und der Ni-katalysierten Polymerisation von Isocyaniden. Mittels ROMP konnten stabile Dispersionen erzeugt werden, welche Partikel mit verschiedensten Molekulargewichten, Größen und Morphologien enthielten. Diese Eigenschaften konnten durch die Wahl des Monomers, die Katalysatorkonzentration oder den Emulgatortyp beeinflusst werden. Des Weiteren wurden Partikel mit komplexen Morphologien wie Kern-Schale-Strukturen synthetisiert. Dazu erfolgte die Generierung von Partikeln aus Poly(urethan) oder Poly(norbornenderivaten), welche in situ und ohne intermediäre Aufarbeitung mit einer Schale aus Poly(methacrylat) versehen wurden. Der Nachweis dieser Strukturen gelang mittels verschiedener Schwermetall-Markierungsverfahren in der Transmissionselektronenmikroskopie. Schlussendlich erfolgte die Herstellung von hochvernetzten und molekular geprägten Poly(acrylsäure)-Partikeln. Hierbei wurden unterschiedliche pharmakologische Wirkstoffe und Farbstoffe in die Partikel eingebracht, um deren Migrationsverhalten und Wiederanbindung an die Partikel zu untersuchen. Weiterhin wurden die Partikel erfolgreich in Zellaufnahmeexperimenten eingesetzt.

Corrosion protection of PVD and paint coatings for selective solar absorber surfaces

The selective solar absorber surface is a fundamental part of a solar thermal collector, as it is responsible for the solar radiation absorption and for reduction of radiation heat losses. The surface’s optical properties, the solar absorption (á) and the emittance (å), have great impact on the solar thermal collector efficiency. In this work, two coatings types were studied: coatings obtained by physical vapor deposition (PVDs) and coatings obtained by projection with different paints (PCs) on aluminum substrates. The most common industrial high performing solar selective absorbers are nowadays produced by vacuum deposition methods, showing some disadvantages, such as lower durability, lower resistance to corrosion, adhesion and scratch, higher cost and complex production techniques. Currently, spectrally selective paints are a potential alternative for absorbing surfaces in low temperature applications, with attractive features such as ease of processing, durability and commercial availability with low cost. Solar absorber surfaces were submitted to accelerated ageing tests, specified in ISO 22975-3. This standard is applicable to the evaluation of the long term behavior and service life of selective solar absorbers for solar collectors working under typical domestic hot water system conditions. The studied coatings have, in the case of PVDs solar absorptions between 0.93 and 0.96 and emittance between 0.07 and 0.10, and in the case of PCs, solar absorptions between 0.91 and 0.93 and emittance between 0.40 and 0.60. In addition to evaluating long term behavior based on artificial ageing tests, it is also important to know the degradation mechanism of different coatings that are currently in the market. Electrochemical impedance spectroscopy (EIS) allows for the assessment of mechanistic information concerning the degradation processes, providing quantitative data as output, which can easily relate to the kinetic parameters of the system. EIS measures were carried out on Gamry FAS2 Femostat coupled with a PCL4 Controller. Two electrolytes were used, 0.5 M NaCl and 0.5 M Na2SO4, and the surfaces were tested at different immersion times up to 4 weeks. The following types of specimens have been tested: Aluminium with/without surface treatment, 3 selective paint coatings (one with a poly(urethane) binder and two with silicone binders) and 2 PVD coatings. Based on the behaviour of the specimens throughout the 4 weeks of immersion, it is possible to conclude that the coating showing the best protective properties corresponds to the selective paint coating with a polyurethane resin followed by the other paint coatings, whereas both the PVD coatings do not confer any protection to the substrate, having a deleterious effect as compared to the untreated aluminium reference.

Controlled release of urea encapsulated by starch-g-poly(L-lactide)

This paper presented a new approach for preparing a new type of slow-release membrane-encapsulated urea fertilizer with starch-g-PLLA as biodegradable carrier materials. By solution-casting and washing rapidly with water the urea was individually encapsulated within the starch matrix modified by L-lactide through in situ graft-copolymerization.

Spectroscopic Study on Water Diffusion in Poly(ester urethane) Block Copolymer Matrix

The diffusion of water in a phase-separated biodegradable poly(ester urethane) shape-memory polymer with poly(E-caprolactone) (PCL) as the soft segment was investigated using time-resolved FTIR-ATR. On the basis of the band fitting and water ordering in drawn films, the broad water band in the 3800-2800 cm(-1) region was decomposed into four bands located at 3620, 3510, 3400, and 3260 cm(-1), and the first two components at 3620 and 35 10 cm(-1) were assigned to the vibrations of antisymmetric and symmetric stretching of water hydrogen bonded with the C=O group of the soft segment. The other two were associated with water bonded to the urethane hard segments in the forms of N-H:O-H:O=C bridge hydrogen bond and double hydrogen bonds with two C=O groups, respectively. Furthermore, band fitting and two-dimensional correlation analyses revealed that in the diffusion process, water first diffuses into the continuous soft-rich PCL phase and then into the hard-rich urethane domains, forming double hydrogen bonds with two C=O groups prior to the bridge hydrogen bond in the form of N-H:O-H:O=C.

Hydrogen Bonding and Crystallization in Biodegradable Multiblock Poly(ester urethane) Copolymer

The hydrogen bonding and crystallization of a biodegradable poly(ester urethane) copolymer based on poly(L-lactide) (PLLA) as the soft segment were investigated by FTIR. On slow cooling from melt, the onset and the progress of the crystallization of the urethane hard segments were correlated to the position, width, and relative intensity of the hydrogen-bonded N-H stretching band. The interconversion between the "free" and hydrogen-bonded N-H and C=O groups in the urethane units in the process was also revealed by 2D correlation analysis of the FTIR data. The crystallization of the PLLA soft segments was monitored by the ester C=O stretching and the skeletal vibrations. It was revealed that the PLLA crystallization was restricted by the phase separation and the urethane crystallization, and at cooling rates of 10 degrees C/min or higher, the crystallization of the PLLA soft segments was prohibited.

Synthesis and physical properties of lipid-based poly(ester-urethane)s, I: Effect of varying polyester segment length

Four aliphatic thermoplastic poly(ester-urethane)s (PEUs) with similar molecular weights but varying polyesters molecular weight (534-1488 g/mol) were prepared from polyester diols, obtained by melt condensation of Azelaic acid and 1,9-Nonanediol, and 1,7-heptamethylene di-isocyanate (HPMDI) all sourced from vegetable oil feedstock. The thermal, and mechanical properties, and crystal structure of PEUs were investigated using DSC, TGA, DMA, tensile analysis and WAXD. For sufficiently long polyester chain, WAXD data indicated no hydrogen bonds polyethylene (PE)-like crystalline packing and for short polyester chains, small crystal domains with significant H-bonded polyamide (PA)-like packing. Crystallinity decreased with decreasing polyester molecular weights. The polymorphism of PEUs and consequently their melting characteristics were found to be largely controlled by polyester segment length. TGA of the PEUs indicated improved thermal stability with decreasing polyester chain length, suggesting a stabilization effect by urethane groups. Mechanical properties investigated by DMA and tensile analysis were found to scale predictably with the overall crystallinity of PEUs. (C) 2012 Elsevier Ltd. All rights reserved.

Fabrication, structural characterization, and applications of Langmuir and Langmuir-Blodgett films of a poly(azo)urethane

The synthesis of a poly(azo)urethane by fixing CO2 in bis-epoxide followed by a polymerization reaction with an azodiamine is presented. Since isocyanate is not used in the process, it is termed clean method and the polymers obtained are named NIPUs (non-isocyanate polyurethanes). Langmuir films were formed at the air-water interface and were characterized by surface pressure vs mean molecular area per met unit (Pi-A) isotherms. The Langmuir monolayers were further studied by running stability tests and cycles of compression/expansion (possible hysteresis) and by varying the compression speed of the monolayer formation, the subphase temperature, and the solvents used to prepare the spreading polymer solutions. The Langmuir-Blodgett (LB) technique was used to fabricate ultrathin films of a particular polymer (PAzoU). It is possible to grow homogeneous LB films of up to 15 layers as monitored using UV-vis absorption spectroscopy. Higher number of layers can be deposited when PAzoU is mixed with stearic acid, producing mixed LB films. Fourier transform infrared (FTIR) absorption spectroscopy and Raman scattering showed that the materials do not interact chemically in the mixed LB films. The atomic force microscopy (AFM) and micro-Raman technique (optical microscopy coupled to Raman spectrograph) revealed that mixed LB films present a phase separation distinguishable at micrometer or nanometer scale. Finally, mixed and neat LB films were successfully characterized using impedance spectroscopy at different temperatures, a property that may lead to future application as temperature sensors. Principal component analysis (PCA) was used to correlate the data.

Molecular architecture of thin films fabricated via physical vapor deposition and containing a poly(azo)urethane

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)