Coeficientes de perda de carga em valvulas e acessorios no escoamento laminar de fluidos nao-Newtonianos

Friction loss coefficients for laminar flow of xantan gum solutions (concentrations in the range of 0.1-0.5% by weight) through valves and fittings were experimentally determined. The rheological behavior, studied by means of a concentric cylinder rheometer, was pseudoplastic, being well described by the Ostwald-De Waele model with non-linear correlation coefficients (r) between 0.998 and 0.999. In the pressure drop measurements the following fittings were employed: completely open and half way open ball valve, completely open and half way open angle valve, tee used like coupling, tee used like a 90° elbow, short radius 90° elbow and coupling. The results showed that the friction loss coefficients increased with decreasing generalized Reynolds number. The friction loss coefficients could be well adjusted by a potential model, suggested by Kittredge & Rowley (1957) for Newtonian fluids, K f = A(Re g) -B, with correlation coefficients between 0.837 and 0.999.

Friction losses in valves and fittings for liquid food products

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Experimental and analytical investigation of refrigerant and lubricant migration

The off-cycle refrigerant mass migration has a direct influence on the on-cycle performance since compressor energy is necessary to redistribute the refrigerant mass. No studies, as of today, are available in the open literature which experimentally measured the lubricant migration within a refrigeration system during cycling or stop/start transients. Therefore, experimental procedures measuring the refrigerant and lubricant migration through the major components of a refrigeration system during stop/start transients were developed and implemented. Results identifying the underlying physics are presented. The refrigerant and lubricant migration of an R134a automotive A/C system-utilizing a fixed orifice tube, minichannel condenser, plate and fin evaporator, U-tube type accumulator and fixed displacement compressor-was measured across five sections divided by ball valves. Using the Quick-Closing Valve Technique (QCVT) combined with the Remove and Weigh Technique (RWT) using liquid nitrogen as the condensing agent resulted in a measurement uncertainty of 0.4 percent regarding the total refrigerant mass in the system. The determination of the lubricant mass distribution was achieved by employing three different techniques-Remove and Weigh, Mix and Sample, and Flushing. To employ the Mix and Sample Technique a device-called the Mix and Sample Device-was built. A method to separate the refrigerant and lubricant was developed with an accuracy-after separation-of 0.04 grams of refrigerant left in the lubricant. When applying the three techniques, the total amount of lubricant mass in the system was determined to within two percent. The combination of measurement results-infrared photography and high speed and real time videography-provide unprecedented insight into the mechanisms of refrigerant and lubricant migration during stop-start operation. During the compressor stop period, the primary refrigerant mass migration is caused by, and follows, the diminishing pressure difference across the expansion device. The secondary refrigerant migration is caused by a pressure gradient as a result of thermal nonequilibrium within the system and causes only vapor phase refrigerant migration. Lubricant migration is proportional to the refrigerant mass during the primary refrigerant mass migration. During the secondary refrigerant mass migration lubricant is not migrating. The start-up refrigerant mass migration is caused by an imbalance of the refrigerant mass flow rates across the compressor and expansion device. The higher compressor refrigerant mass flow rate was a result of the entrainment of foam into the U-tube of the accumulator. The lubricant mass migration during the start-up was not proportional to the refrigerant mass migration. The presence of water condensate on the evaporator affected the refrigerant mass migration during the compressor stop period. Caused by an evaporative cooling effect the evaporator held 56 percent of the total refrigerant mass in the system after three minutes of compressor stop time-compared to 25 percent when no water condensate was present on the evaporator coil. Foam entrainment led to a faster lubricant and refrigerant mass migration out of the accumulator than liquid entrainment through the hole at the bottom of the U-tube. The latter was observed for when water condensate was present on the evaporator coil because-as a result of the higher amount of refrigerant mass in the evaporator before start-up-the entrainment of foam into the U-tube of the accumulator ceased before the steady state refrigerant mass distribution was reached.

Sistema limpo em linha para extração em fase sólida de contaminantes emergentes em águas naturais

A solid-phase in-line extraction system for water samples containing low levels of emerging contaminants is described. The system was specially developed for large volume samples (up to 4 L) using commercial solid-phase extraction (SPE) cartridges. Four sets containing PTFE-made connectors, brass adapters and ball valves were used to fit SPE cartridges and sample bottles to a 4-port manifold attached to a 20 L carboy. A lab-made vacuum device was connected to the manifold cap. The apparatus is robust and less expensive than the typical available system. Its also provides less experimental handling, avoiding cross contamination and sample losses.

Upgrade of an experimental volumetric unit for gas adsorption equilibrium studies

In this work, a volumetric unit previously assembled by the research group was upgraded. This unit revamping was necessary due to the malfunction of the solenoid valves employed in the original experimental setup, which were not sealing the gas properly leading to erroneous adsorption equilibrium measurements. Therefore, the solenoid valves were substituted by manual ball valves. After the volumetric unit improvement its operation was validated. For this purpose, the adsorption equilibrium of carbon dioxide (CO2) at 323K and 0 - 20 bar was measured on two different activated carbon samples, in the of extrudates (ANG6) and of a honeycomb monolith (ACHM). The adsorption equilibrium results were compared with data previously measured by the research group, using a high-pressure microbalance from Rubotherm GmbH (Germany) – gravimetric. The results obtained using both apparatuses are coincident thus validating the good operation of the volumetric unit upgraded in this work. Furthermore, the adsorption equilibrium of CO2 at 303K and 0 - 10 bar on Metal-Organic Frameworks (MOFs) Cu-BTC and Fe-BTC was also studied. The CO2 adsorption equilibrium results for both MOFs were compared with the literature results showing good agreement, which confirms the good quality of the experimental results obtained in the new volumetric unit. Cu-BTC sample showed significantly higher CO2 adsorption capacity when compared with the Fe-BTC sample. The revamping of the volumetric unit included a new valve configuration in order to allow testing an alternative method for the measurement of adsorption equilibrium. This new method was employed to measure the adsorption equilibrium of CO2 on ANG6 and ACHM at 303, 323 and 353K within 0-10 bar. The good quality of the obtained experimental data was testified by comparison with data previously obtained by the research group in a gravimetric apparatus.

Monitoimipystysorvin NC- ohjelmoinnin kehittäminen CAM käyttöönotolla

Diplomityön tavoitteena oli tehostaa venttiilipesien koneistuksessa käytettävän monitoimipystysorvin NC - ohjelmointia CAM - ohjelman käyttöönotolla. Tutkimus on osa laajempaa kokonaisuutta liittyen koneistusalihankinnan kehittämiseen ja yrityksen kilpailukyvyn ylläpitoon ja parantamiseen liiketoiminta-alueella, jolla on tällä hetkellä hyvät kasvunäkymät. Tavoite rajattiin yritykseen jo aiemmin hankitun WinCAM - ohjelman päivittämiseen ja hyödyntämiseen monitoimipystysorvin NC - ohjelmoinnissa. Tutkimuksen käytännön tavoitteena oli selvittää CAM - ohjelmoinnin käyttömahdollisuudet, sekä luoda CAM - ohjelmistoon pohjautuva, räätälöity NC - ohjelmointikonsepti pilottikohteeseen. Tutkimuksen kokeellisen osuuden muodostivat tällöin nykyisen tuotannon ongelmakohtien löytäminen, koneen ohjelmointitarpeiden kartoitus,sekä menetelmäkehitys. Tutkimuksen päämääränä oli tuotannon tasolla käytettävä järjestelmä, jolla koneen ohjelmointi olisi mahdollista myös vähemmällä konekohtaisella kokemuksella. Nykyisen toimintatavan ongelmina olivat yhtenäisen NC - ohjelmointikäytännön puute, niin valmiiden ohjelmien käytössä kuin uusienkin ohjelmien tekemisessä. Tähän olivat syynä NC - ohjauksen heikko käytettävyys erityisesti sorvauksen osalta. Nämä tekijät yhdistettynä monitoimityöstökoneessa tarvittavaan koordinaatiston hallintaan vaikeuttivat ohjelmointia. Työntekijäkohtaiset erot NC - ohjelmien käytössä, sekä laadultaan vaihtelevat valuaihiot aiheuttivat tuotannon läpäisyaikaan merkittävää vaihtelua. Siten myös koneen kuormituksen säätely oli vaikeaa. Uuden ohjelmointikonseptin toteutuksessa pidettiin etusijalla hyvää käytettävyyttä, sekä uuden menetelmän aukotonta liittymistä olemassa oleviin tuotantojärjestelmiin. Ohjelmointikonseptin toteutuksessa, osaperheestä haettiin selkeästi parametroitaviksi soveltuvat työvaiheet, jotka voitiin hallita yleiskäyttöisillä aliohjelmilla. Tuotteiden muidengeometrioiden hallintaan laadittiin geometriakirjasto, jota voitiin käyttää tavanomaisen graafisen ohjelmoinnin pohjana. Vanhaa toimintatapaa ja diplomityön aikana kehitettyä CAM - ohjelmointijärjestelmää vertailtiin perustuen NC - ohjelmien tehokkuuteen, jota tarkasteltiin saman työvaiheen työstöaikaan perustuen. Tämän lisäksi tärkeän tuloksen muodostavat myös kvalitatiivisetseikat, jotka liittyvät ohjelmointiympäristön käytettävyyteen. CAM - ohjelmoinnin kehittäminen ja käyttöönotto pilottikohteessa sujui pääosin hyvin ja laaditunsuunnitelman mukaisesti. Aiemmin hankalasti ohjelmoitavat työvaiheet, kuten erilaisten laippatasopintojen ja reikäpiirien ohjelmointi muutettiin makrokäyttöön soveltuviksi. Sorvauksessa ongelmia aiheuttaneen tiivistelilan koneistukseen sovellettiin graafista ohjelmointia. Koko tuotannon mittakaavassa NC - ohjelmoinninosuus oli kuitenkin vähäinen, mistä johtuen koneen tuottavuuteen ei tutkimuksenajanjaksolla voitu vaikuttaa. Sen sijaan tuotannon sujuvuuteen oleellisesti vaikuttavaa työtekijöiden 'hiljaisen tiedon' määrää voitiin vähentää vakioimalla ohjelmointia ja siirtämällä tehokkaiksi havaitut menetelmät ohjelmointijärjestelmään.

Sistema limpo em linha para extração em fase sólida de contaminantes emergentes em águas naturais

A solid-phase in-line extraction system for water samples containing low levels of emerging contaminants is described. The system was specially developed for large volume samples (up to 4 L) using commercial solid-phase extraction (SPE) cartridges. Four sets containing PTFE-made connectors, brass adapters and ball valves were used to fit SPE cartridges and sample bottles to a 4-port manifold attached to a 20 L carboy. A lab-made vacuum device was connected to the manifold cap. The apparatus is robust and less expensive than the typical available system. Its also provides less experimental handling, avoiding cross contamination and sample losses.

John Fischer, UM Men's Golf, on UM Golf Course, 1935 teamed with Chuck Kocsis in arranged match with professionals, Olin Dutra, National Open champion and famed long-ball hitter Jimmy Thompson.

[Ensian caption: "Professional star admiring on the country's leading amateurs. Fischer whisks one down the fairway while [Olin] Dutra, Chuck Kocsis and Thompson follow the bounding ball."]

Living-engineered valves for transcatheter venous valve repair.

Background: Chronic venous insufficiency (CVI) represents a major global health problem with increasing prevalence and morbidity. CVI is due to an incompetence of the venous valves, which causes venous reflux and distal venous hypertension. Several studies have focused on the replacement of diseased venous valves using xeno- and allogenic transplants, so far with moderate success due to immunologic and thromboembolic complications. Autologous cell-derived tissue-engineered venous valves (TEVVs) based on fully biodegradable scaffolds could overcome these limitations by providing non-immunogenic, non-thrombogenic constructs with remodeling and growth potential. Methods: Tri- and bicuspid venous valves (n=27) based on polyglycolic acid-poly-4-hydroxybutyrate composite scaffolds, integrated into self-expandable nitinol stents, were engineered from autologous ovine bone-marrow-derived mesenchymal stem cells (BM-MSCs) and endothelialized. After in vitro conditioning in a (flow) pulse duplicator system, the TEVVs were crimped (n=18) and experimentally delivered (n=7). The effects of crimping on the tissue-engineered constructs were investigated using histology, immunohistochemistry, scanning electron microscopy, grating interferometry (GI), and planar fluorescence reflectance imaging. Results: The generated TEVVs showed layered tissue formation with increasing collagen and glycosaminoglycan levels dependent on the duration of in vitro conditioning. After crimping no effects were found on the MSC level in scanning electron microscopy analysis, GI, histology, and extracellular matrix analysis. However, substantial endothelial cell loss was detected after the crimping procedure, which could be reduced by increasing the static conditioning phase. Conclusions: Autologous living small-diameter TEVVs can be successfully fabricated from ovine BM-MSCs using a (flow) pulse duplicator conditioning approach. These constructs hold the potential to overcome the limitations of currently used non-autologous replacement materials and may open new therapeutic concepts for the treatment of CVI in the future.

Remplacement valvulaire percutané au moyen de stent-valves : une nouvelle approche thérapeutique [Stents valves for percutaneous valve replacement]

Stents have a long history in traditional valve surgery as both, porcine biological valves as well as pericardial valves are mounted on stents prior to implantation. Recently stent-mounted biological devices have been compressed up to the point, where they can be passed through a catheter. Various routes can be distinguished for implantation: open access, the trans-vascular route in antegrade or retrograde fashion, as well as direct trans-apical or trans-atrial access. Direct access has the potentialforvideo-endoscopic valve replacement. In theory, as well as in the experimental setting, valved stents have been implanted in tricuspid and caval position respectively, as well as in pulmonary, mitral and aortic locations. The largest clinical experience has been achieved in pulmonary position whereas current efforts target the aortic position.

Improving Dynamic Characteristics of Open-loop Controlled Log Crane

The improvement of the dynamics of flexible manipulators like log cranes often requires advanced control methods. This thesis discusses the vibration problems in the cranes used in commercial forestry machines. Two control methods, adaptive filtering and semi-active damping, are presented. The adaptive filter uses a part of the lowest natural frequency of the crane as a filtering frequency. The payload estimation algorithm, filtering of control signal and algorithm for calculation of the lowest natural frequency of the crane are presented. The semi-active damping method is basedon pressure feedback. The pressure vibration, scaled with suitable gain, is added to the control signal of the valve of the lift cylinder to suppress vibrations. The adaptive filter cuts off high frequency impulses coming from the operatorand semi-active damping suppresses the crane?s oscillation, which is often caused by some external disturbance. In field tests performed on the crane, a correctly tuned (25 % tuning) adaptive filter reduced pressure vibration by 14-17 % and semi-active damping correspondingly by 21-43%. Applying of these methods require auxiliary transducers, installed in specific points in the crane, and electronically controlled directional control valves.

Fungus ball in the urinary tract: A rare entity.

A fungal mass in the urinary tract (fungus ball), mainly occurring in compromised patients, is a rare and dangerous complication of candiduria. We report 2 cases of fungus ball associated with hydronephrosis and sepsis. As reported in the literature, we treated the first patient by prompt relief of obstruction by nephrostomy and local and systemic antifungal agent. The second patient failed to respond to this treatment due to a distal ureteral stenosis and required open surgery with fungus ball removal and ureteral reimplantation. Despite a large success in urinary tract drainage with antifungal treatments, some cases need a modified approach due to anatomical modification.

Friction losses in valves and fittings for power-law fluids

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Friction losses in valves and fittings for viscoplastic fluids

Data on pressure drop were obtained in stainless steel, sanitary fittings and valves during laminar and turbulent flow of aqueous suspensions of sucrose and bentonite. The rheological properties of these suspensions were determined and the Bingham model provided the best fitting with the experimental data. Friction losses were measured in fully- and partially-open butterfly and plug valves, bends and union. Values of loss coefficients (k(f)) were calculated and correlated as functions of the classical Reynolds number and the Reynolds number proposed by Govier and Aziz (1972) for viscoplastic fluids. The two-k method and a new proposed model presented the best adjustments for the Govier and Aziz Reynolds number, and Hedstrom and classical Reynolds numbers, respectively.