Determination of PAH, PCB, and OCP in water from the Three Gorges Reservoir accumulated by semipermeable membrane devices (SPMD)

Bioavailable water concentrations of polycyclic aromatic hydrocarbons (PAH), polychlorinated biphenyls (PCB) and organochlorine pesticides (OCP) were measured in the water column from Three Gorges Reservoir (TGR) collected in May 2008 using semipermeable membrane devices (SPMDs). The sampling sites spanned the whole reservoir from the upstream Chongqing to the great dam covering more than 600 km long distance with water flow velocities ranging from <0.05 to 1.5 m s(-1). This is the first experience of SPMD application in the biggest reservoir in the world. The results of water sampling rates based on performance reference compounds (PRC) were tested to be significantly correlated with water flow velocities in the big river. Results of back-calculated aqueous concentrations based on PRC showed obvious regional variations of PAH, PCB and OCP levels in the reservoir. Total PAH ranged from 13.8 to 97.2 ng L-1, with the higher concentrations occurring in the region of upstream and near the dam. Phenanthrene, fluoranthene, pyrene and chrysene were the predominant PAH compounds in TGR water. Total PCB ranged from 0.08 to 0.51 ng L-1, with the highest one occurring in the region near the dam. PCB 28, 52, 101, 138, 153, 180, 118 were the most abundant PCB congeners in the water. The total OCP ranged from 2.33 to 3.60 ng L-1 and the levels showed homogenous distribution in the whole reservoir. HCH, DDT and HCB, PeCB were the major compounds of OCP fingerprints. Based on water quality criteria, the TGR water could be designated as being polluted by HCB and PAH. Data on PAH, PCB and OCP concentrations found in this survey can be used as reference levels for future POP monitoring programmes in TGR. (C) 2009 Elsevier Ltd. All rights reserved.

Estudo da influência dos íons K+, Mg2+, SO4 2- e CO3 2- na cristalização biomimética de fosfato de cálcio amorfo (ACP) e conversão a fosfato octacálcico (OCP)

The crystallization of hydroxyapatite (HA) in aqueous solution can be described by the mechanism ACP → OCP → HA. In this work, it was studied the influence of K+, Mg2+, SO4 2- AND CO3 2- ions in the formation of ACP and in its conversion to OCP, using biomimetic coatings on metallic substrates of commercially pure titanium (Ti c.p.). The results showed that Mg2+ and CO3 2- ions favored both the formation of ACP and its conversion to OCP. Differently, K+ and SO4 2- ions did not influence the formation of ACP and, consequently, interfered in the conversion to OCP.

In vitro and in vivo biological behavior of CDHA/OCP/β-TCP scaffold

The biological behavior of a new bioactive material composed of calcium-deficient hydroxyapatite, octacalcium phosphate, and beta-tricalcium phosphate was investigated by in vitro indirect and direct cytotoxicity, cell adhesion and proliferation tests, and by in vivo subcutaneous and bone implantation in rats. The results of the in vitro studies showed that the material is biocompatible and no cytotoxic. Slightly poorer initial cell adhesion and lower cell proliferation than in control was observed, which were attributed to the reactivity and roughness of the material surface, In vivo results showed that the material is biodegradable and bioactive in bone tissue, but only biocompatible and partially biodegradable in soft tissue.

Reactions to changes in work control: Implications for self-determined and non-self-determined individuals

We investigate the extent to which individuals’ global motivation (self-determined and non-self-determined types) influences adjustment (anxiety, positive reappraisal) and engagement (intrinsic motivation, task performance) in reaction to changes to the level of work control available during a work simulation. Participants (N = 156) completed 2 trials of an inbox activity under conditions of low or high work control—with the ordering of these levels varied to create an increase, decrease, or no change in work control. In support of the hypotheses, results revealed that for more self-determined individuals, high work control led to the increased use of positive reappraisal. Follow-up moderated mediation analyses revealed that the increases in positive reappraisal observed for self-determined individuals in the conditions in which work control was high by Trial 2 consequently increased their intrinsic motivation toward the task. For more non-self-determined individuals, high work control (as well as changes in work control) led to elevated anxiety. Follow-up moderated mediation analyses revealed that the increases in anxiety observed for non-self-determined individuals in the high-to-high work control condition consequently reduced their task performance. It is concluded that adjustment to a demanding work task depends on a fit between individuals’ global motivation and the work control available, which has consequences for engagement with demanding work.

武汉东湖上覆水和沉积物中磷形态的垂直分布特征

武汉东湖是有代表性的城市浅水型湖泊。于春、夏两季对东湖庙湖湖区的上覆水和沉积物柱状样品进行了磷的形态分析,研究了各种磷形态在上覆水及沉积物垂直方向上的分布特征。结果表明,春夏两季东湖上覆水总磷(TP)含量分别为1.11和1.25mg·L-1,超过国家标准近6倍,富营养化程度严重。春季湖水中磷主要以颗粒态形式存在,夏季主要以溶解态形式存在。春季湖区沉积物中铁结合磷(Fe-P)比例最大,占沉积物TP的44.3%,夏季闭蓄磷(OcP)比例最大,占TP的36.3%,高比例的Fe-P从沉积物角度说明了庙湖湖区的污染

Model based control for closed loop testing of 1-D engine simulation models

1-D engine simulation models are widely used for the analysis and verification of air-path design concepts and prediction of the resulting engine transient response. The latter often requires closed loop control over the model to ensure operation within physical limits and tracking of reference signals. For this purpose, a particular implementation of Model Predictive Control (MPC) based on a corresponding Mean Value Engine Model (MVEM) is reported here. The MVEM is linearised on-line at each operating point to allow for the formulation of quadratic programming (QP) problems, which are solved as the part of the proposed MPC algorithm. The MPC output is used to control a 1-D engine model. The closed loop performance of such a system is benchmarked against the solution of a related optimal control problem (OCP). As an example this study is focused on the transient response of a light-duty car Diesel engine. For the cases examined the proposed controller implementation gives a more systematic procedure than other ad-hoc approaches that require considerable tuning effort. © 2012 IFAC.

PCBs and OCPs in human milk and selected foods from Luqiao and Pingqiao in Zhejiang, China

This study was conducted to measure the levels of 23 PCB congeners and 6 organochlorine pesticides (OCPs) in human milk and three food types collected from Luqiao and Pingqiao in Zhejiang Province, China. An effort was also made to explore the potential health risk for the mothers and breast-fed infants living in these two localities. Luqiao was selected as the sampling site because it is the largest place for the disassembly of obsolete transformers and electrical waste in China. Pingqiao, located 100 kin NW of Luqiao, is not known to be a place for any electronic or electrical waste and hence was chosen as the control site. Both localities are important agricultural places in the province. The organochlorines were measured in the samples using the GC-PECD technique. Micro-EROD bioassay method was also used as a complement of the chemical analysis to estimate the TEQ levels of dioxin-like PCBs in human milk. The data showed that the human milk, rice, hen egg, and fish samples from Luqiao were more heavily contaminated with PCBs than those from Pingqiao, suggesting that the mothers and their breast-fed infants in Luqiao tended to receive greater exposure to PCBs than those living in Pingqiao. The OCP levels in the two localities were found comparable, suggesting that the major source of contamination with these pesticides was from their agricultural uses. Significant correlation (R-2 = 0.87, P < 0.001) of PCB TEQs was found between the bioassay and chemical analysis method, suggesting that micro-EROD is an effective method for comprehensive determination of TEQ levels in human milk. Comparison with literature data showed that the PCB levels in milk samples from Luqiao were significantly higher than those from localities in other Chinese provinces and comparable to those in developed or industrialized countries. (c) 2007 Published by Elsevier B.V.

Monitoring of organochlorine pesticides using PFU csystems in Yunnan lakes and rivers, China

Polyurethane foam unit (PFU) systems were collected from 11 lakes and three rivers in the Yunnan Plateau, China and, the PFU extrusion liquids, were analyzed for organochlorine pesticides (OCPs) by gas chromatography with electron capture detection (GCECD). The concentrations of pp'-DDE, HCB and HCHs were undetectable to 1.86 mu g l(-1) (mean 0.27 mu g l(-1)), undetectable to 0.72 mu g l(-1) (mean 0.11 mu g l(-1)), and 0.24-21.95 mu g l(-1) (mean 7.39 mu g l(-1)) respectively in lakes; and those in rivers were undetectable to 0.23 mu g l(-1) (mean 0.08 mu g l(-1)), 0.68-2.93 mu g l(-1) (mean 1.70 mu g l(-1)), and 2.71-37.56 mu g l(-1) (mean 17.01 mu g l(-1)) respectively. Notably, some residue levels of OCPs exceeded the US National Recommended Water Quality Criteria, implying Yunnan has levels of OCPs potentially harmful to human health. Further, the contamination by OCPs showed an obvious spatial distribution pattern. Amongst the lakes, Dianchi, Xingyun, Lugu and Yangzonghai had the highest OCP levels dominated by beta-HCH, whereas among rivers, Nujiang and Lancang Rivers had the highest contents of OCPs dominated by alpha-HCH. This demonstrates that HCHs are the predominant contaminants and some point sources of HCHs may still exist in Yunnan. The pollution levels in Yunnan were compared with other studies, suggesting the PFU method is suitable for long-term on-line monitoring of trace OCPs in aquatic ecosystems. Therefore, continuous studies monitoring OCPs in lakes and rivers are needed to further understand the future trend of contamination. (c) 2006 Elsevier Ltd. All rights reserved.

异氰酸醋官能化乙丙共聚物的制备及其与尼龙6共混体系的研究

本工作合成了一种含异氰酸酷功能基团的不饱和单体，（3-异氰酸酯基-4-甲基）苯氨基甲酸-2-丙烯配（TAI）。以过氧化二异丙苯（OCP）为引发剂，该单体被用于乙烯丙烯共聚物（EPM）的自由基溶液接枝官能化。纯化后的接枝产物（EPM-g-TAI）的傅立叶变换红外光谱中存在2273cm-l异氰酸酷基团（-NCO），表明异氰酸醋单体已经接枝到乙丙共聚物上。接枝率采用化学滴定和红外光谱的方法确定。与EPM相比，EPM-g-TAl的分子量分布（MMO）变窄。采用旋转流变仪测定了EPM-g-TAl的流变行为。EPM-g-TAl的表观粘度高于EPM且随接枝率的增加而增加。采用接触角测定的表面分析表明，对于给定的的极性测定液体接枝产物的接触角随接枝率的增加而增大；我们同时得到接枝产物的表面自由能（75）以及表面自由能的色散分量（γs）和表面自由能的极性分量（γsρ），这些参数随接枝率提高而增大的趋势使我们可以定量估计接枝反应对改善极性的贡献。本工作研究了（3一异氰酸酯基-4-甲基）苯氨基甲酸-2-丙烯醋（TAl）官能化乙烯丙烯共聚物（EPM-g-TAI）与尼龙6（PA6）的反应共混。傅立叶变换红外光谱表明，由于EPM-g-TAl中的异氰酸醋基（-NCO）与尼龙6中的端胺基（-NH2）之间的化学反应：EPM-g-TAI／PA6谱图中3299cm-1处的阵日伸缩振动峰变窄变高，1640cm-1处阵日变形振动峰和1547cm-1处阵日弯曲振动峰变强。同时研究了共混体系的热性能、流变性能、机械性能和形态特征。OSC结果表明，在相同的共混组成下，EPM-g-TAI／PA6共混体系中尼龙6的结晶烩（△Hc）到氏于EPM／PA6共混体系中的尼龙6，这种差别随着共混物中乙烯丙烯共聚物含量的增加而增大，说明反应共混体系中尼龙6的结晶受到一定的限制；EPM-g-TAI／PA6共混体系的复数粘度和贮能模量高于相应的EPM／PA6共混体系；与相同组成的EPM／PA6相比，EPM-g-TAI／PA6中分散相的粒子尺寸更小，粒子分布更均匀，界面粘合更强；反应共混后的机械性能如拉伸强度、杨氏模量，弯曲强度和模量、缺口及非缺口冲击强度均随着接枝率的提高而增加。

多类型混合运算的面向对象设计与实现

针对多种数据类型的混合运算问题进行了研究。讨论了面向过程的解决方案和两种可能的面向对象解决方案及不足。依据敏捷设计原则,提出了一种双层函数指针数组(虚表)的面向对象新方案。分析表明,该设计具备开放封闭性,解决了灵活性、可重用性、可维护性和效率问题。

Effect of Process Conditions on Microstructure and Corrosion Resistance of Cold-Sprayed Ti Coatings

Ti and Ti alloys can be applied to steels as a protective coating in view of its excellent resistance to corrosive environment. Cold spraying, as a new coating technique, has potential advantages in fabrication of Ti coating in comparison with conventional thermal spraying techniques. In this study, Ti coatings were prepared on carbon steel substrates by cold spraying via controlling the process conditions. The microstructure of coatings was observed by SEM. The porosity of coatings was estimated by image analysis and the bond strength was tested for comparison of the process conditions. Potentiodynamic polarization and open-circuit potential (OCP) measurements were performed to understand the corrosion behavior of the coatings. The SEM examination shows that the coatings become more compact with the increases of pressure and temperature of driving gas. The potentiodynamic polarization curves indicate that the coating which has lower porosity has lower corrosion current. The polarization and OCP measurement reveal that cold-sprayed Ti coating can provide favorable protection to carbon steel substrate. The polishing treatment of coating surface polishes the rough outer layer including the small pores as well as decreases the actual surface area of the coating, leading to the considerable improvement of corrosion resistance.

Susceptibility to environmentally induced cracking of laser-welded NiTi wires in Hanks’ solution at open-circuit potential

In the present study the tensile and super-elastic behaviours of laser-welded NiTi wires in Hanks’ solution at open-circuit potential (OCP) were investigated using tensile and cyclic slow-strain-rate tests (SSRT). In comparison with NiTi weldment tested in oil (non-corrosive environment), the weldment in Hanks’ solution suffered from obvious degradation in the tensile properties as evidenced by lower tensile strength, reduced maximum elongation, and a brittle fracture mode. Moreover, a larger residual strain was observed in the weldment after stress–strain cycles in Hanks’ solution. In addition to the microstructural defects resulting from the welding process, the inferior tensile and super-elastic behaviours of the NiTi weldment in Hanks’ solution could be attributed to the trapping of a large amount of hydrogen in the weld zone and heat-affected zone.

Reduction of environmentally induced cracking of laser-welded shape memory NiTi wires via post-weld heat-treatment

In this study, the environmentally induced cracking behaviour of the NiTi weldment with and without post-weld heat-treatment (PWHT) in Hanks’ solution at 37.5 °C at OCP were studied by tensile and cyclic slow-strain-rate tests (SSRT), and compared with those tested in oil (an inert environment). Our previous results in the tensile and cyclic SSRT showed that the weldment without PWHT showed high susceptibility to the hydrogen cracking, as evidenced by the degradation of tensile and super-elastic properties when testing in Hanks' solution. The weldment after PWHT was much less susceptible to hydrogen attack in Hanks' solution as no obvious degradation in the tensile and super-elastic properties was observed, and only a very small amount of micro-cracks were found in the fracture surface. The susceptibility to hydrogen cracking of the NiTi weldment could be alleviated by applying PWHT at the optimized temperature of 350 °C after laser welding.

Prescription contraception use: a cross-sectional population study of psychosocial determinants

Objective: Many forms of contraception are available on prescription only for example, the oral contraceptive pill (OCP) and long-acting reversible contraceptives (LARCs). In this analysis we aim to identify key determinants of prescription contraceptive use.

Design: Cross-sectional population survey. Data on sociodemographic indices, concerns about the OCP and perceived barriers to access were collected.

Setting: Data set constructed from a representative population-based telephone survey of community dwelling adults in the Republic of Ireland (RoI)

Participants: 1515 women aged between 18 and 45 years

Main outcome measure: Self-reported user of the OCP or LARCs (intrauterine contraception, contraceptive injections or subdermal contraceptive implants) in the previous 12 months.

Results: For at least some of the previous year, 35% had used the OCP and 14% had used LARCs, while 3% had used two or more of these methods. OCP users were significantly younger, more likely to be unmarried and had higher income than non-users. Overall, 68% agreed with the statement ‘that taking a break from long-term use of the contraceptive pill is a good idea’ and 37% agreed with the statement that ‘the OCP has dangerous side effects’ and this was the strongest predictor variable of non-use of the OCP. Intrauterine contraception users were significantly older, more likely to be married and had lower income than non-users. Injections or subdermal contraceptive implant users were significantly younger, less likely to be married, had lower income and were less likely to agree that taking a break from long-term use of the pill is a good idea than non-users.

Conclusions: Prescription contraceptive use is sociodemographically patterned, with LARCs in particular being associated with lower incomes in the RoI. Concerns about the safety of the OCP remain prevalent and are important and modifiable determinants of contraceptive-related behaviour.

Analysing organochlorine pesticides in strawberry jams using GC-ECD, GC-MS/MS and QuEChERS sample preparation

This paper describes a comparison of adaptations of the QuEChERS (quick, easy, cheap, effective, rugged and safe) approach for the determination of 14 organochlorine pesticide (OCP) residues in strawberry jam by concurrent use of gas chromatography (GC) coupled to electron capture detector (ECD) and GC tandem mass spectrometry (GC-MS/MS). Three versions were tested based on the original QuEChERS method. The results were good (overall average of 89% recoveries with 15% RSD) using the ultrasonic bath at five spiked levels. Performance characteristics, such as accuracy, precision, linear range, limits of detection (LOD) and quantification (LOQ), were determined for each pesticide. LOD ranged from 0.8 to 8.9 microg kg-1 ; LOQ was in the range of 2.5–29.8 microg kg- 1; and calibration curves were linear (r2>0.9970) in the whole range of the explored concentrations (5–100 microg kg- 1). The LODs of these pesticides were much lower than the maximum residue levels (MRLs) allowed in Europe for strawberries. The method was successfully applied to the quantification of OCP in commercially available jams. The OCPs were detected lower than the LOD.