Influência da acrilamida e da poliacrilamida em sistema microemulsionado visando aplicação na recuperação avançada de petróleo

This work aims to study the influence of two additives, the monomer, acrylamide and its polymer, polyacrylamide, solubilized in microemulsion systems and applied on enhanced oil recovery. By the microemulsion system obtained, it was chosen points into the phase diagram, presenting these compositions: 25%, 30%, 35% C/T; 2% Fo (fixed for all points) e 73%, 68% e 63% Fa, respectively. However, the monomer and the polymer were solubilized in these microemulsion points with 0.1%; 0.5%; 1% e 2% of concentration, ordering to check the concentration influence at the physicochemical properties (surface tension and rheology) of the microemulsion. Through the salinity study, was possible to observe that the concentrations of 1% and 2% of polymer made the solution became blurred, accordingly, the study of surface tension and rheology only was made for the concentrations of 0.1% e 0.5% of monomer and polymer, respectively. By the surface tension study it was observed that how the concentration of active matter (C/T) was increasing the surface tension was amending for each system, with or without additives. In the rheology study, as it increases the concentration of active matter increases both the viscosity of the microemulsion system (SME) with no additive, as the SME with polymer (AD2). After the entire study, it was chosen the lower point of active matter (25% C/T; 2% Fo e 73% Fa), plus additives in concentrations of 0.1% and 0.5% to be used on enhanced oil recovery. Assays were made on sandstone from Botucatu Formation, where after the tests, it was concluded that among the studied points, the point who showed the best efficiency of advanced shift was the microemulsion system + 0.5% AD2, with a recovery of 28% of oil in place and a total of 96,49%, while the other solution with 0.5% of polymer presented the worst result, with 14.1% of oil in place and 67,39% of efficiency of total displacement

Hidrólise e caracterização de poliacrilamida hidrofobicamente modificada: avaliação da aplicabilidade na recuperação de petróleo

The hydrolysis reaction in alkaline conditions of the commercial polymer poly(acrylamide-co-metacrylate of 3,5,5-trimethyl-hexane) called HAPAM, containing 0.75 % of hydrophobic groups, was carried out in 0.1 M NaCl and 0.25M NaOH solutions, varying the temperature and reaction time. The polymers were characterized by 1H and 13C Nuclear Magnetic Resonance (NMR), Elemental Analysis and Size Exclusion Chromatography (SEC). The values of the hydrolysis degree were obtained by 13C NMR. The viscosity of HAPAM and HAPAM-10N-R solutions was evaluated as a function of shear rate, ionic strength and temperature. At high polymer concentration (Cp), the viscosity of HAPAM solutions increased with the ionic strength and decreased with the temperature. The viscosity of HAPAM-10N-R solutions increased significantly in distilled water, due to repulsions between the carboxylate groups. At high Cp, with the increase of ionic strength and temperature, occurred a decrease of viscosity, due to mainly the high hydrolysis degree and the low amount of hydrophobic groups. These results indicated that the studied polymers have properties more suitable for the application in Enhanced Oil Recovery (EOR) in low salinity and moderate temperature reservoirs

Caracterização de poliacrilamida parcialmente hidrolisada em regime concentrado

A partially hydrolyzed polyacrylamide (HPAM) is a copolymer composed of acrylamide and sodium acrylate. Due to its wide range of applications there are different methods for its quantification and characterization in solution systems. Evaluation of C* is important to describe the transition from dilute to semi-dilute, behavior, when the solution will have its characteristic viscosity at concentrations above C*. This dissertation describes the determination of the critical concentration of overlap C* by potentiometry of partially hydrolyzed polyacrylamide - HPAM under acidic conditions. Based on the law of mass action and the proper treatment of the constant of aggregate formation, polymer molecular weight, degree of polymerization and hydrolysis were calculated. The inflection point was determined by the intersection of the resulting equation and mathematical development, statistically satisfy the experimental points relating the number of moles of monomers (n), equilibrium constant of formation of the entanglements (K*), pH, C* and acidity constant of the polymer (Ka). The viscometric parameters of C* showed a percentage difference compared to potentiometers. The results for the determination of C*, and degree of copolymerization molar mass proved to be a simple alternative for the characterization of polymers with protonated monomers and water soluble

Influência da densidade de carga e da massa molar da poliacrilamida na reologia de sistemas microemulsionados

The knowledge of the rheological behavior of microemulsionated systems (SME) is of fundamental importance due to the diversity of industrial applications of these systems. This dissertation presents the rheological behavior of the microemulsionated system formed by RNX 95/alcohol isopropyl/p-toulen sodium sulfonate/kerosene/distilled water with the addition of polyacrylamide polymer. It was chosen three polymers of the polyacrylamide type, which differ in molar weight and charge density. It was studied the addition of these polymers in relatively small concentration 0,1% in mass and maximum concentration of 2,0%. It was made analysis of flow to determine the appearing viscosities of the SME and rheological parameters applying Bingham, Ostwald de Waale and Herschell-Buckley models. The behavior into saline environment of this system was studied for a solution of KCl 2,0%, replacing the distilled water. It was determined the behavior of microemulsions in relation with the temperature through curves of flow in temperatures of 25 to 60ºC in variations of 5ºC. After the analysis of the results the microemulsion without the addition of polymer presented a slight increase in its viscosity, but it does not mischaracterize it as a Newtonian fluid. However the additive systems when analyzed with low concentration of polymer adjusted well to the applied models, with a very close behavior of microemulsion. The higher concentration of the polymer gave the systems a behavior of plastic fluid. The results of the temperature variation point to an increase of viscosity in the systems that can be related to structural changes in the micelles formed in the own microemulsion without the addition of polymer

Extração e análise eletroforética em gel de poliacrilamida (SDS-PAGE) de proteínas totais de folhas e raízes de Piper tuberculatum

O Estado do Pará é o principal produtor brasileiro de pimenta-do-reino (Piper nigrum Link), entretanto a sua produção tem sido bastante afetada pela doença conhecida como fusariose. O Fusarium solani f. sp. piperis é o agente causador desta doença que afeta o sistema radicular da planta, causando o apodrecimento das raízes e a queda das folhas levando à morte da planta. Algumas piperáceas nativas da região amazônica, entre elas a espécie Piper tuberculatum Jacq., têm se mostrado resistentes à infecção pelo F. solani f. sp. piperis, e desta forma têm sido utilizadas em estudos de interação planta-patógeno. Neste trabalho foram avaliadas cinco condições de extração de proteínas com o objetivo de selecionar tampões adequados para a extração de proteínas totais de folhas e raízes de P. tuberculatum. Os tampões utilizados para a extração de proteínas de raízes e folhas foram: tampão salino, tampão sacarose, tampão glicerol, tampão uréia e tampão fosfato de sódio. As análises quantitativas mostraram que os tampões sacarose, glicerol e uréia foram mais eficientes na extração de proteínas de folhas e raízes. Análises de SDS-PAGE mostraram padrões diferenciados de bandas em extratos protéicos de folhas e raízes obtidos com os diferentes tampões. Os resultados obtidos neste trabalho contribuem para a identificação de tampões de extração adequados para a obtenção de amostras de proteínas totais em estudos de interação P. tuberculatum - F. solani f. sp. piperis.

The Economics of CO2-EOR Cluster Developments in the UK Central North Sea/ Outer Moray Firth

NORTH SEA STUDY OCCASIONAL PAPER No. 123

Síntese de hidrogéis e cinética de liberação de amônio e potássio

Hidrogéis produzidos a partir de poliacrilamida (PAAm) foram sintetizados e suas eficiências para liberação controlada de NH4+ e K+ contidos em fertilizantes foram avaliadas. Os hidrogéis foram sintetizados em solução aquosa a partir da polimerização do monômero acrilamida (AAm) em duas concentrações (3,6 e 21,7 %), em presença do agente de reticulação N', N-metileno-bis-acrilamida (MBAAm) e catalisador N, N, N', N'-tetrametil etilenodiamina (TEMED). A fixação de nutrientes ocorreu submetendo-se os hidrogéis à solução aquosa com concentrações de 86 e 82 mg L-1 de K+ e NH4+. As propriedades hidrofílicas, espectroscópicas e morfológicas foram investigadas por meio de medidas de grau de intumescimento (Q), por espectroscopia no infravermelho com transformada de Fourier (FTIR) e por meio de imagens obtidas por microscopia eletrônica de varredura (MEV). Os teores de NH4+ e K+ liberados em meio aquoso foram monitorados em intervalos de tempo de 1, 2, 4, 18, 26 e 50 h por espectrofotometria com análise por injeção em fluxo e por fotometria de chama. Os resultados de grau de intumescimento mostraram que hidrogéis com nutrientes fixados são mais hidrofóbicos. Observações em MEV revelaram decréscimo no tamanho médio dos poros para os hidrogéis com maior quantidade de acrilamida. A cinética de liberação controlada de NH4+ e K+ permitiu inferir que o hidrogel sintetizado com 21,7 % de AAm apresentou maior potencial na liberação controlada dos nutrientes, principalmente NH4+.

Estructura cristalina del N-isopropil-2-ciano-3(5'-nitrofuril)acrilamida

C11H11N3O4 , Mr = 249.23, triclinic, , a = 5.453(1), b = 22.873(5), c = 4.893(1) Å, a = 94.47(3), b = 96.36(3), g = 86.27(3)º, V = 603.7(8)ų,Z = 2, Dx = 1.371 Mg/m-3,l(Cu Ka1) = 1.54178Å, m = 0.86mm-1, room temperature. The crystal structure of N-isopropyl-2-cyano-3(5'-nitrofuryl) - acrylamide has been determined by Direct Methods and refined to R = 0.086 for 797 observed reflections. The molecules in the crystal are packed at normal van der Waals forces and by an hydrogen bond between N1-H1...02i (N1...02i: 2.910(1)Å), with i=x,y,z+1).

Estudo de liberação e permeação in vitro do diclofenaco de dietilamônio em microemulsão gel-like

The goal of this study was to produce and characterize a new microemulsion gel-like carrier system (MEG) by using the pseudo-ternary phase-diagram concept. The diclofenac diethylamine (DDA) was incorporated in the MEG and its in vitro release and permeation profiles were performed using Franz-type diffusion cells. The results revealed that the commercial DDA emulgel provided significantly higher Kp of DDA (2.2-fold) as compared to the MEG. Similar data were obtained in the permeation studies in which DDA Kp 4.7-fold higher. Therefore, MEG presents higher potential as a topical delivery system for DDA when compared to the commercial DDA emulgel.

Correlação entre parâmetros da cinética de intumescimento com características estruturais e hidrofílicas de hidrogéis de poliacrilamida e metilcelulose

In this paper, the effects of acrylamide (AAm), methylcellulose (MC) contents, pH and ionic strength on kinetic, network and hydrophilic properties of polyacrylamide and methylcellulose hydrogels were investigated. The hydrogels were characterized by evaluating of network [average molecular weight between crosslinks (M C), crosslink density (q) and the number of elastically effective chains (Ve)], and kinetic parameters [diffusional exponent (n), diffusion constant (k) and diffusion coefficient (D)]. Such properties were controlled by adjusting of the AAm, MC contents, pH and ionic strength factors. Due to high hydrophilicity and fast water-uptake, the PAAm-MC hydrogels can be considered as materials for potential applications in agricultural fields, mainly in controlled release of water or pesticides.

Influência da quantidade de amônio na síntese de nanopartículas de óxido de ferro por microemulsão

Iron oxide nanoparticles were synthesized in microemulsion systems composed by Triton X-100/hexyl alcohol/cyclohexane/aqueous solution. The nanoparticles were synthesized in microemulsions containing different amounts of ammonium, in order to evaluate the influence of this parameter on the size of the nanoparticles and on the phase transformation after heat treatment. Powder materials were obtained after centrifugation, washing and drying, and they were analyzed as synthesized and after heating at 350, 500 and 1000 °C. It was observed that the higher amount of ammonium induced smaller particles and minor phase transformation, possibly due to a preferential nucleation process.

Síntese e caracterização de hidrogéis compósitos a partir de copolímeros acrilamida-acrilato e caulim: efeito da constituição de diferentes caulins do nordeste brasileiro

Superabsorbent hydrogels based on poly (acrylamide-co-acrylate) and different kaolins, were prepared by free-radical aqueous copolymerization. FTIR and WAXS techniques were employed for characterization of a series of hydrogels, obtained by varying the percentage of clay, crosslinking and constitution of kaolin. The water absorbency at equilibrium (Weq) decreased with increasing clay content and the amount of crosslinking agent. Superabsorbent hydrogel (Weq > 1084 g H2O/g gel) was obtained as 10 wt% of white kaolin and 0.05 mol% of crosslinking agent were used. The hydrogel proved sensitive to pH variation and the presence of salts.

Avaliação do potencial anticorrosivo de tiossemicarbazonas solubilizadas em microemulsão

In this paper, thiosemicarbazones 4-N-cinnamoyl-thiosemicarbazone (CTSC), 4-N-(2'-methoxycinnamoyl)-thiosemicarbazone (MCTSC), and 4-N-(4'-hydroxy-3'-methoxybenzoyl)- thiosemicarbazone (HMBTSC) were solubilized in an oil-in-water (O/W) microemulsion system (ME_OCS), forming systems CTSC_ME_OCS, MCTSC_ME_OCS and HMBTSC_ME_OCS. The effectiveness of these systems in the process of inhibiting AISI 1020 carbon steel corrosion was evaluated in a saline solution (NaCl 0.5%), using a galvanostatic method. The tested thiosemicarbazones showed higher inhibitory effects (85.7% for CTSC_ME_OCS, 84.0% for MCTSC_ME_OCS, and 83.3% for HMBTSC_ME_OCS). The surfactant OCS (dissolved in H2O) and the ME_OCS system showed lower efficacies, with 71.0% for OCS and 74.0% for ME_OCS system.

Hidrogeles microestructurados de acrilamida y determinación de su capacidad de absorber agua y etanol

This paper reports the synthesis of nanostructured hydrogels of acrylamide by a two-step polymerisation process. The first step is performed by inverse microemulsion polymerization (water-in-oil) of N-isopropylacrylamide (NIPA), with these particles then added to aqueous solutions of acrylamide (AM), adding a crosslinking agent. The polymerization reaction is then initiated, thereby producing nanostructured hydrogels. We determined the capacity to absorb water, water and / or ethanol when nanostructured hydrogels were immersed in aqueous solutions with different concentrations of ethanol. It was found that the hydrogels were selective in absorbing water in all cases increasing with the ethanol concentration of the solutions.

Obtenção da fase peroviskita via microemulsão

Pequenas partículas de fase peroviskita de BaMnO3 foram preparadas por dois métodos: a rota da coprecipitação convencional (RCC) e o método convencional de microemulsão (MCM). As técnicas instrumentais utilizadas para caracterizar as amostras foram: microscopia eletrônica de varredura (SEM), difratometria de raios X (XRD), termogravimetria (TG) e análise térmica diferencial (DTA). A síntese de materiais em sistemas coloidais auto-organizados tem por objetivo aumentar a homogeneidade de tamanho e forma das partículas. Nos últimos anos aumentou a busca por materiais mais uniformes visando o aperfeiçoamento da microestrutura. A rota de microemulsão é um método alternativo para a síntese de materiais porque permite o controle da relação entre as concentrações de água e do tensoativo, (w), o qual controla o tamanho das gotículas de microemulsão denominadas microreatores. Peroviskita pura obtida de microemulsão forma-se em temperatura menor do que a fase precipitada, e resulta.em partículas com distribuição de tamanho mais adequada, de aproximadamente 0,1 mm de diâmetro comparado com a média de 0,5 mm das partículas coprecipitadas.