Production of low methoxyl pectin using immobilized pectin methylesterase silica from acerola (Malpighia glabra L.)

The aim of this work was to develop an efficient reactor for the production of low methoxyl pectin, using pectinmethylesterase (PME, EC 3.1.1.11) from acerola immobilized on silica. The immobilized enzyme was used in up to 50 successive bioconversion runs at 50 degrees C with an efficiency loss of less than 20%. The fixed-bed reactor (6.0 x 1.5 cm) was prepared using PME immobilized in glutaraldehyde-activated silica operated at 50 degrees C with an optimum flow rate of 10 mL h(-1). The bioconversion yield was shown to strongly depend on the nature of the enzymatic preparation. An efficiency of 44% was achieved when concentrated PME was used, compared with only 30% with purified PME, both after an 8-h run. The process described could provide the basis for the development of a commercial-scale process. (c) 2006 Society of Chemical Industry.

Gelatin-immobilized pectinmethylesterase for production of low methoxyl pectin

The optimum conditions for the production of low methoxyl pectin using pectinmethylesterase (PME) from acerola (Malpighia glabra L.), immobilized in gelatin, have been established by factorial design and response surface methodology. In the case of the free enzymes the optimum conditions for activity, within ranges adequate for food processing, are low NaCl concentrations (0.10 M), relatively high temperatures (55 degreesC) and slightly basic pH values (pH = 9). The temperature and pH seem to have strong influence on the observed activity. In the immobilized enzyme, optimum NaCl concentration was 0.15 M, while the optimum pH remained at 9.0. (C) 2003 Elsevier Ltd. All fights reserved.

Alkali hydroxide-induced gelation of pectin

The mechanism of pectin gelation depends on the degree of methoxylation. High methoxyl pectin gels due to hydrophobic interactions and hydrogen bonding between pectin molecules. Low methoxyl pectin forms gels in the presence of di- and polyvalent cations which cross link and neutralise the negative charges of the pectin molecule. Monovalent cations normally do not lead to gel formation with high methoxyl pectin solutions free of divalent cations, especially Ca. The present study found that alkali (NaOH or KOH) added to high methoxyl pectin leads to gel formation in a concentration-depended manner. It was also found that monovalent cations (Na and K) induce gelation of low methoxyl pectin and the time required for gel formation (setting time) depends on the cation concentration. The results indicate that a combined char-e neutralisation and ionic strength effect is responsible for the monovalent cation-induced gelation of pectin. (C) 2003 Elsevier Ltd. All rights reserved.

Effects of polar group saturation on physical gelation of Amphiphilic polymer solutions

Monte Carlo simulation on the basis of the comblike coarse grained nonpolar/polar (NP) model has been carried out to study the polar group saturation effect on physical gelation of amphiphilic polymer solutions. The effects of polar group saturation due to hydrogen bonding or ion bridging on the sol-gel phase diagram, microstructure of aggregates, and chain conformation of amphiphilic polymer solutions under four different solvent conditions to either the nonpolar backbone or the polar side chain in amphiphilic polymer chains have been investigated. It is found that an increase of polar group saturation results in a monotonically decreased critical concentration of gelation point, which can be qualitatively supported by the dynamic theological measurements on pectin aqueous solutions. Furthermore, various solvent conditions to either the backbone or the side chain have significant impact on both chain conformation and microstructure of aggregates. When the solvent is repulsive to the nonpolar backbone but attractive to the polar side chain, the polymer chains are collapsed, and the gelation follows the mechanism of colloidal packing; at the other solvent conditions, the gelation follows the mechanism of random aggregation.

Microencapsulação por gelificação iônica e interação eletrostática do corante de buriti (Mauritia flexuosa L. f.)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Antimicrobial and physical-mechanical properties of pectin/papaya puree/cinnamaldehyde nanoemulsion edible composite films

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Properties of ectin isolated from Lawulu (Crysophylum roxbergi G Don) and development of jam and fruit leather using Lawulu and pineapple

Lawulu fruit (Crysophylum roxberghi GDon) possess nutritional, medicinal and functional properties. However, it is less consumed due to its  characteristic off flavour. The present study was carried out to investigate the potential of utilizing lawulu fruit for isolation of pectin and to develop jam and fruit leather. Products were evaluated based on physico-chemical and sensory properties.

Pectin isolated fromf irm ripe lawuluf ruit using 0.1 M hydrochloric acid  followed by 96% ethanol precipitation yielded 7. 3% pectin on wet weight basis and 26.1% on dry weight basis. The isolated pectin contained 0.74% ash, 0.02% acetyl content and 7.85% methoxyl content with equivalent weight 993.5. These values were comparable with commercial high methoxyl pectin. In addition, Iawulu pectin at 1.5% concentration formed a gel within 12-14 min in the presence of 68% sucrose and 0.5% citric acid.

Jam was prepared by using Iawulu-pineapple ratio as 1:2, 1:1 and 2:1 respectively. The gel strength of jam (65⁰ Brix and pH 3.1) at 0.35% commercial high methoxyl pectin was comparable with commercial mixed fruit jam. Sensory evaluation indicated a significant preference (p<.05) for jam containing lawulu-pineapple ratio of 1:2 and 1.1 respectively overthe ratio of 2:1. With increased lawulu percentage both yellowness and lightness of jam increased significantly (p<0.05).

Fruit leather was prepared by changing lawulu-pineapple ratio as 1:2, 1:1 and 2:1 respectively with 20% sucrose, 0.3% citric acid, 0.05% pectin and 100 ppm potassium metabisulphite followed by drying at 65±1⁰C for 12-14 h. Sensory evaluation data revealed that changes in lawulu-pineapple ratio had no significant effect on taste, texture and overall quality of fruit leather.   However, significant preference (p<0.05) for colour was observed with increasing lawulu percentage. Both yellowness (b' value) and lightness (L'value) of fruit leather were sign[icantly increased (p<0.05) with increasing lawulu percentage.

Effect of extrusion on the emulsifying properties of soybean proteins and pectin mixtures modelled by response surface methodology

The objective of this study was to apply response surface methodology to estimate the emulsifying capacity and stability of mixtures containing isolated and textured soybean proteins combined with pectin and to evaluate if the extrusion process affects these interfacial properties. A simplex-centroid design was applied to the model emulsifying activity index (EAI), average droplet size (D-[4.3]) and creaming inhibition (Cl%) of the mixtures. All models were significant and able to explain more than 86% of the variation. The high predictive capacity of the models was also confirmed. The mean values for EAI, D-[4.3] and Cl% observed in all assays were 0.173 +/- 0.015 mn, 19.2 +/- 1.0 mu m and 53.3 +/- 2.6%, respectively. No synergism was observed between the three compounds. This result can be attributed to the low soybean protein solubility at pH 6.2 (<35%). Pectin was the most important variable for improving all responses. The emulsifying capacity of the mixture increased 41% after extrusion. Our results showed that pectin could substitute or improve the emulsifying properties of the soybean proteins and that the extrusion brings additional advantage to interfacial properties of this combination. (C) 2008 Elsevier Ltd. All rights reserved.

Effect of Controlled Atmospheres with Low Oxygen Levels on Extended Storage of Guava Fruit (Psidium guajava L. 'Pedro Sato')

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Multiparticulate systems of pectin-chitosan: Study of swelling and drug release

The aim of this study was to prepare multiparticulate systems of pectin:chitosan (PC:CS) and to evaluate their swelling ratio and the drug release in different environments. PC:CS particles containing triamcinolone were prepared by a complex coacervation/ionotropic gelation method in aqueous environment. The polymer ratio, the calcium concentration and the contact time of the capsules with chitosan dispersion for particles formation and the structures obtained were analyzed. The systems were characterized in relation to morphology, size, swelling, and drug release behavior. The methodology used allowed the production of spherical particles with narrow range of size distribution. The entrapment efficiency for triamcinolone was 84.31 ± 439. It was observed that the particles present a relatively low swelling ratio in acidic medium and a larger swelling ratio in enteric medium. The release profile was dependent on pH and can be related with the swelling ratio.

Natural Pectin Polysaccharides as Edible Coatings

The most fashionable trends in food packaging research are targeted towards improvements in food quality and safety by increasing the use of environmentally-friendly materials, ideally those able to be obtained from bio-based resources and presenting biodegradable characteristics. Edible films represent a key area of development in new multifunctional materials by their character and properties to effectively protect food with no waste production. The use of edible films should be considered as a clean and elegant solution to problems related with waste disposal in packaging materials. In particular, pectin has been reported as one of the main raw materials to obtain edible films by its natural abundance, low cost and renewable character. The latest innovations in food packaging by the use of pectin-based edible films are reviewed in this paper, with special focus on the use of pectin as base material for edible coatings. The structure, properties related to the intended use in food packaging and main applications of pectins are herein reported.

A new low temperature synthesis route of fraipontite (Zn,Al)3(Si,Al)2O5(OH)4

A low temperature synthesis method based on the decomposition of urea at 90°C in water has been developed to synthesise fraipontite. This material is characterised by a basal reflection 001 at 7.44 Å. The trioctahedral nature of the fraipontite is shown by the presence of a 06l band around 1.54 Å, while a minor band around 1.51 Å indicates some cation ordering between Zn and Al resulting in Al-rich areas with a more dioctahedral nature. TEM and IR indicate that no separate kaolinite phase is present. An increase in the Al content however, did result in the formation of some SiO2 in the form of quartz. Minor impurities of carbonate salts were observed during the synthesis caused by to the formation of CO32- during the decomposition of urea.