How to run a community recycling center : a resource guide to low-technology recycling in Illinois /

Location of title page varies with copies.

Melhoria da eficiência energética em edifícios dos anos 70: implementação de soluções sustentáveis low-tech e low-cost

Dissertação de mestrado em Construção e Reabilitação Sustentáveis

Teaching project: a low-cost swine model for chest tube insertion training

Objective: to describe and evaluate the acceptance of a low-cost chest tube insertion porcine model in a medical education project in the southwest of Paraná, Brazil. Methods: we developed a low-cost and low technology porcine model for teaching chest tube insertion and used it in a teaching project. Medical trainees - students and residents - received theoretical instructions about the procedure and performed thoracic drainage in this porcine model. After performing the procedure, the participants filled a feedback questionnaire about the proposed experimental model. This study presents the model and analyzes the questionnaire responses. Results: seventy-nine medical trainees used and evaluated the model. The anatomical correlation between the porcine model and human anatomy was considered high and averaged 8.1±1.0 among trainees. All study participants approved the low-cost porcine model for chest tube insertion. Conclusion: the presented low-cost porcine model for chest tube insertion training was feasible and had good acceptability among trainees. This model has potential use as a teaching tool in medical education.

Seed size and genotype effects on maize (Zea mays L.) yield under different technology levels

Final plant population in maize crop was used as a basis to identify the technology level of a given farmer. Final population of 50,000 plants/hectare was considered as an indication of a high technology level farmer; 35,000 of a medium, and 20,000 of a low technology level farmer. These populations were artificially obtained for the hybrids HT-2X, BR-201, and BR-205 from small, medium and large seeds. The results showed the triple cross hybrid HT-2X to be the most indicated for low technology level regions, due to its lesser sensitivity to variations in seed size and also to its significant outyielding of the other two hybrids. The double cross hybrids BR-201 and BR-205 exhibited much higher sensitivity to variations in seed size so that if they have to be used in a low technology region, the most recommended procedure would be to make use of the largest possible seeds. In conclusion, genotype and seed size seem to be factors capable of compensating for plant population reductions in maize crops. The more prolific hybrids and the largess seeds are more indicated for low technology level regions.

Intermediation for technology diffusion and user innovation in a developing rural economy:a social learning perspective

Technology intermediaries are seen as potent vehicles for addressing perennial problems in transferring technology from university to industry in developed and developing countries. This paper examines what constitutes effective user-end intermediation in a low-technology, developing economy context, which is an under-researched topic. The social learning in technological innovation framework is extended using situated learning theory in a longitudinal instrumental case study of an exemplar technology intermediation programme. The paper documents the role that academic-related research and advisory centres can play as intermediaries in brokering, facilitating and configuring technology, against the backdrop of a group of small-scale pisciculture businesses in a rural area of Colombia. In doing so, it demonstrates how technology intermediation activities can be optimized in the domestication and innofusion of technology amongst end-users. The design components featured in this instrumental case of intermediation can inform policy making and practice relating to technology transfer from university to rural industry. Future research on this subject should consider the intermediation components put forward, as well as the impact of such interventions, in different countries and industrial sectors. Such research would allow for theoretical replication and help improve technology domestication and innofusion in different contexts, especially in less-developed countries.

Tecnologias de apoio e multideficiência: recursos mediadores da aprendizagem e da inclusão

Dissertação apresentada à Escola Superior de Educação de Lisboa para obtenção do grau de Mestre em Ensino Especial – ramo de Problemas de Cognição e Multideficiência

Comércio bilateral Portugal - Brasil

Dissertação apresentada ao Instituto Superior de Contabilidade e Administração do Porto para obtenção do Grau de Mestre em Empreendedorismo e Internacionalização Orientadora: Professora Doutora Celsa Maria de Carvalho Machado

Innovation sources and productivity in Catalonian firms: a quantile regression analysis

This paper explores the effects of two main sources of innovation -intramural and external R&D- on the productivity level in a sample of 3,267 Catalonian firms. The data set used is based on the official innovation survey of Catalonia which was a part of the Spanish sample of CIS4, covering the years 2002-2004. We compare empirical results by applying usual OLS and quantile regression techniques both in manufacturing and services industries. In quantile regression, results suggest different patterns at both innovation sources as we move across conditional quantiles. The elasticity of intramural R&D activities on productivity decreased when we move up the high productivity levels both in manufacturing and services sectors, while the effects of external R&D rise in high-technology industries but are more ambiguous in low-technology and knowledge-intensive services. JEL codes: O300, C100, O140. Keywords: Innovation sources, R&D, Productivity, Quantile regression

Innovation sources and productivity: a quantile regression analysis

This paper explores the effects of two main sources of innovation —intramural and external R&D— on the productivity level in a sample of 3,267 Catalan firms. The data set used is based on the official innovation survey of Catalonia which was a part of the Spanish sample of CIS4, covering the years 2002-2004. We compare empirical results by applying usual OLS and quantile regression techniques both in manufacturing and services industries. In quantile regression, results suggest different patterns at both innovation sources as we move across conditional quantiles. The elasticity of intramural R&D activities on productivity decreased when we move up the high productivity levels both in manufacturing and services sectors, while the effects of external R&D rise in high-technology industries but are more ambiguous in low-technology and services industries.

Innovation sources and productivity in Catalonian firms: a quantile regression analysis

This paper explores the effects of two main sources of innovation - intramural and external R&D— on the productivity level in a sample of 3,267 Catalonian firms. The data set used is based on the official innovation survey of Catalonia which was a part of the Spanish sample of CIS4, covering the years 2002-2004. We compare empirical results by applying usual OLS and quantile regression techniques both in manufacturing and services industries. In quantile regression, results suggest different patterns at both innovation sources as we move across conditional quantiles. The elasticity of intramural R&D activities on productivity decreased when we move up the high productivity levels both in manufacturing and services sectors, while the effects of external R&D rise in high-technology industries but are more ambiguous in low-technology and knowledge-intensive services. JEL codes: O300, C100, O140 Keywords: Innovation sources, R&D, Productivity, Quantile Regression

Key competences in the new ventures: a model for evaluating

This research studies from an internal view based on the Competency-Based Perspective (CBP), key organizational competencies developed for small new business. CBP is chosen in an attempt to explain the differences characterizing the closed companies from the consolidated ones. The main contribution of this paper is the definition of a set of key organizational competencies for new ventures from services and low technology based sectors. Using the classification proposed by [1] and a review of the entrepreneurship literature, the main competencies were defined and classified as: managerial, input-based, transformation-based, and output-based competencies. The proposed model for evaluating new ventures organizational competence is tested by means of Structural Equation

Wet oxidation of recalcitrant lignin waters: Experimental and kinetic studies

The dissertation is based on four articles dealing with recalcitrant lignin water purification. Lignin, a complicated substance and recalcitrant to most treatment technologies, inhibits seriously pulp and paper industry waste management. Therefore, lignin is studied, using WO as a process method for its degradation. A special attention is paid to the improvement in biodegradability and the reduction of lignin content, since they have special importance for any following biological treatment. In most cases wet oxidation is not used as a complete ' mineralization method but as a pre treatment in order to eliminate toxic components and to reduce the high level of organics produced. The combination of wet oxidation with a biological treatment can be a good option due to its effectiveness and its relatively low technology cost. The literature part gives an overview of Advanced Oxidation Processes (AOPs). A hot oxidation process, wet oxidation (WO), is investigated in detail and is the AOP process used in the research. The background and main principles of wet oxidation, its industrial applications, the combination of wet oxidation with other water treatment technologies, principal reactions in WO, and key aspects of modelling and reaction kinetics are presented. There is also given a wood composition and lignin characterization (chemical composition, structure and origin), lignin containing waters, lignin degradation and reuse possibilities, and purification practices for lignin containing waters. The aim of the research was to investigate the effect of the operating conditions of WO, such as temperature, partial pressure of oxygen, pH and initial concentration of wastewater, on the efficiency, and to enhance the process and estimate optimal conditions for WO of recalcitrant lignin waters. Two different waters are studied (a lignin water model solution and debarking water from paper industry) to give as appropriate conditions as possible. Due to the great importance of re using and minimizing the residues of industries, further research is carried out using residual ash of an Estonian power plant as a catalyst in wet oxidation of lignin-containing water. Developing a kinetic model that includes in the prediction such parameters as TOC gives the opportunity to estimate the amount of emerging inorganic substances (degradation rate of waste) and not only the decrease of COD and BOD. The degradation target compound, lignin is included into the model through its COD value (CODligning). Such a kinetic model can be valuable in developing WO treatment processes for lignin containing waters, or other wastewaters containing one or more target compounds. In the first article, wet oxidation of "pure" lignin water was investigated as a model case with the aim of degrading lignin and enhancing water biodegradability. The experiments were performed at various temperatures (110 -190°C), partial oxygen pressures (0.5 -1.5 MPa) and pH (5, 9 and 12). The experiments showed that increasing the temperature notably improved the processes efficiency. 75% lignin reduction was detected at the lowest temperature tested and lignin removal improved to 100% at 190°C. The effect of temperature on the COD removal rate was lower, but clearly detectable. 53% of organics were oxidized at 190°C. The effect of pH occurred mostly on lignin removal. Increasing the pH enhanced the lignin removal efficiency from 60% to nearly 100%. A good biodegradability ratio (over 0.5) was generally achieved. The aim of the second article was to develop a mathematical model for "pure" lignin wet oxidation using lumped characteristics of water (COD, BOD, TOC) and lignin concentration. The model agreed well with the experimental data (R2 = 0.93 at pH 5 and 12) and concentration changes during wet oxidation followed adequately the experimental results. The model also showed correctly the trend of biodegradability (BOD/COD) changes. In the third article, the purpose of the research was to estimate optimal conditions for wet oxidation (WO) of debarking water from the paper industry. The WO experiments were' performed at various temperatures, partial oxygen pressures and pH. The experiments showed that lignin degradation and organics removal are affected remarkably by temperature and pH. 78-97% lignin reduction was detected at different WO conditions. Initial pH 12 caused faster removal of tannins/lignin content; but initial pH 5 was more effective for removal of total organics, represented by COD and TOC. Most of the decrease in organic substances concentrations occurred in the first 60 minutes. The aim of the fourth article was to compare the behaviour of two reaction kinetic models, based on experiments of wet oxidation of industrial debarking water under different conditions. The simpler model took into account only the changes in COD, BOD and TOC; the advanced model was similar to the model used in the second article. Comparing the results of the models, the second model was found to be more suitable for describing the kinetics of wet oxidation of debarking water. The significance of the reactions involved was compared on the basis of the model: for instance, lignin degraded first to other chemically oxidizable compounds rather than directly to biodegradable products. Catalytic wet oxidation of lignin containing waters is briefly presented at the end of the dissertation. Two completely different catalysts were used: a commercial Pt catalyst and waste power plant ash. CWO showed good performance using 1 g/L of residual ash gave lignin removal of 86% and COD removal of 39% at 150°C (a lower temperature and pressure than with WO). It was noted that the ash catalyst caused a remarkable removal rate for lignin degradation already during the pre heating for `zero' time, 58% of lignin was degraded. In general, wet oxidation is not recommended for use as a complete mineralization method, but as a pre treatment phase to eliminate toxic or difficultly biodegradable components and to reduce the high level of organics. Biological treatment is an appropriate post treatment method since easily biodegradable organic matter remains after the WO process. The combination of wet oxidation with subsequent biological treatment can be an effective option for the treatment of lignin containing waters.

Crise du secteur manufacturier au Québec : ampleur et nature des restructurations impliquant des licenciements collectifs entre 2003 et 2008

Des données de Statistique Canada montrent que le Québec a perdu 86 700 emplois manufacturiers nets entre 2004 et 2008, ce qui représente un recul de 13,8% (Bernard, 2009). Un dollar canadien fort, la concurrence internationale, les délocalisations de la production et les consolidations globales d'opérations sont souvent mentionnés comme étant les causes des difficultés du secteur manufacturier canadien - principalement concentré au Québec et en Ontario. La crise financière amorcée à l’été 2007, a contribué à aggraver la crise propre au secteur manufacturier dont les origines remontent au début des années 2000 (Weir, 2007; AgirE, 2008; Pilat et al., 2006). Cette recherche examine le processus de restructuration du secteur manufacturier québécois de manière détaillée au niveau des établissements afin d’en évaluer l’ampleur et la nature entre 2003 et 2008. Les données colligées permettent de poser un regard unique et original sur les restructurations ayant impliqué des licenciements collectifs au Québec. Ces données sont issues de deux sources. D'abord, nous avons utilisé une liste d‘entreprises qui ont envoyé un avis de licenciement collectif au Ministère de l’Emploi et de la Solidarité sociale du Québec entre 2003 et 2008. En second lieu, nous avons eu recours aux archives en ligne des médias pour trouver d’autres évènements de restructuration non rapportés par le ministère ainsi que pour obtenir des informations complémentaires sur les évènements déjà compilés dans la liste du ministère. Notre méthodologie de recherche et notre typologie analytique des types de restructuration sont basées sur celles développées par l’European Monitoring Center on Change (EMCC) et reprises dans certaines études comme celles de Bronfenbrenner et Luce (2004) et Hickey et Schenk (soumis). Les résultats, présentés en termes d’événements de restructuration et d’emplois perdus, sont ventilés en fonction de quelques variables (année d’occurrence, taille de l’établissement, sous-secteur d’activité, intensité technologique, région administrative, types de restructuration). Les raisons données par l’entreprise afin de justifier la restructuration ont aussi été colligées. Au cours de la période étudiée, nous avons identifié au total 1 631 évènements de restructurations dans le secteur manufacturier à travers toutes les régions du Québec, qui ont entraîné la perte de 129 383 emplois. Ainsi, 78 246 emplois ont été perdus suite à la réduction des activités de l‘établissement et 51 137 emplois l’ont été suite à la fermeture de leur établissement. La forme la plus fréquente de restructuration est la restructuration interne, suivi par la faillite/fermeture. Les types de restructuration qui ont engendré le plus de pertes d’emplois en moyenne par évènement sont dans l’ordre, la délocalisation, la sous-traitance, la consolidation d’activités ainsi que la fusion-acquisition. L’année 2008 fut celle où il y a eu le plus grand nombre de restructurations. Montréal et la Montérégie sont les régions qui ont le plus été touchées par la restructuration, les pertes d’emplois et les fermetures d’établissements. Les industries à faible intensité technologique ont davantage été frappées par la crise manufacturière. C’est le sous-secteur du papier et du bois qui connu le plus grand nombre d’événements de restructurations. Ce sous-secteur a aussi subi les pertes d’emplois les plus importantes, suivi par le sous-secteur du textile et du vêtement. Ces deux industries se partagent plus de la moitié des fermetures d’établissements. L’insuffisance de la demande (22,1%), la concurrence internationale (14,3%), la hausse de la valeur du dollar canadien (11,2%), la réorganisation interne de l’entreprise (11,1%), la rationalisation des coûts visant une augmentation de la profitabilité (10,1%) ainsi que les difficultés financières (9,9%) sont les motifs principaux donnés par les employeurs. Nos résultats montrent qu’il y a eu deux temps dans l’évolution de la restructuration du secteur manufacturier au Québec. Un premier temps au début de la période où des changements structurels profonds ont été observés dans certaines industries (p.ex. le bois-papier et le textile-vêtement) et un second temps, en fin de période caractérisé par des changements davantage liés à la conjoncture en raison de la crise économique dont les effets commençaient à se faire sentir à ce moment (Institut de la statistique du Québec, 2009a).