Beryllium-7 sorption to inorganic particles in Tahsis Inlet, Nootka Sound, B.C.

Senior thesis written for Oceanography 445

The volumetric fraction of inorganic particles and the flexural strength of composites for posterior teeth

Objective. To evaluate the content of inorganic particles and the flexural strength of new condensable composites for posterior teeth in comparison to hybrid conventional composites.Method. The determination of the content of inorganic particles was performed by mass weighing of a polymerized composite before and after the elimination of the organic phase. The volumetric particle content was determined by a practical method based on Archimedes' principle, which calculates the volume of the composite and their particles by differential mass measured in the air and in water. The flexural. strength of three points was evaluated according to the norm ISO 4049:1988.Results. The results showed the following filter content: Alert, 67.26%; Z-100, 65.27%; Filtek P 60, 62.34%; Ariston pHc, 64.07%; Tetric Ceram, 57.22%; Definite, 54.42%; Solitaire, 47.76%. In the flexural strength test, the materials presented the following decreasing order of resistance: Filtek P 60 (170.02 MPa) > Z-100 (151.34 MPa) > Tetric Ceram (126.14 MPa) = Alert (124.89 MPa) > Ariston pHc (102.00 MPa) = Definite (93.63 MPa) > Solitaire (56.71 MPa).Conclusion. New condensable composites for posterior teeth present a concentration of inorganic particles similar to those of hybrid composites but do not necessarily present higher flexural strength. (C) 2003 Elsevier B.V. Ltd. Alt rights reserved.

Assembly of side-functional monomers with inorganic nanometer particles

Monomers of methacrylate with various pi -conjugated pendants were designed and prepared in our laboratory, The monomer with suitable end-group was successfully assembled with nano-scale inorganic particles to form an orderly-aligned structure that showed special optical properties, both absorption and emission band were much red-shifted compared with the monomer, A new type of organic/inorganic hybrid materials was obtained by in situ polymerization of the assembly, The hybrid materials could also show special optical properties as the assembly, This might open a new route to tune the emission color.

Preparation and characterization of novel nanocomposites of inorganic/polysaccharide type

O uso de polímeros naturais no âmbito da preparação de nanocompósitos não tem sido tão amplamente estudado quando comparado com os polímeros sintéticos. Assim, esta tese tem como objectivo estudar metodologias para a preparação de novos materiais nanocompósitos sob a forma de dispersões e filmes utilizando polissacarídeos como matriz. A tese está dividida em cinco capítulos sendo o último capítulo dedicado às conclusões gerais e a sugestões para trabalhos futuros. Inicialmente é apresentada uma breve revisão bibliográfica sobre os principais temas colocando esta tese em contexto. Considerações sobre o uso de polímeros naturais e a sua combinação com a utilização de nanopartículas inorgânicas para a fabricação de novos bionanocomposites são descritas e os objectivos e outline da tese são também apresentados. No segundo capítulo, a preparação de partículas de sílica puras ou modificadas bem como a sua caracterização por FTIR, SEM, TEM, TGA, DLS (tamanho e potencial zeta) e medições de ângulo de contacto são discutidas. De modo a melhorar a compatibilidade da sílica com os polissacarídeos, as partículas SiO2 foram modificados com dois compostos do tipo organosilano: 3- metacril-oxipropil-trimetoxissilano (MPS) e 3-aminopropil-trimetoxissilano (APS). As partículas SiO2@MPS foram posteriormente encapsuladas com de poli(metacrilato de glicidilo) utilizando a técnica de polimerização em emulsão. A utilização dos nanocompósitos resultantes na preparação de dispersões de bionanocompósitos não foi bem sucedida e por esse motivo não os estudos não foram prosseguidos. O uso de SiO2@APS na preparação de dispersões bionanocomposite foi eficiente. No terceiro capítulo é apresentada uma revisão sobre dispersões bionanocompósitas e respectiva caracterização destacando aspectos fundamentais sobre reologia e microestrutura. Em seguida, é discutido o estudo sistemático realizado sobre o comportamento reológico de dispersões de SiO2 utilizando três polissacarídeos distintos no que concerne a carga e as características gelificantes: a goma de alfarroba (não iónica), o quitosano (catiónico) e a goma xantana (aniónica) cujas propriedades reológicas são amplamente conhecidas. Os estudos reológicos realizados sob diferentes condições demonstraram que a formação de géis frágeis e/ou bem estruturados depende do tamanho SiO2, da concentração, do pH e da força iónica. Estes estudos foram confirmados por análises microestruturais usando a microscopia electrónica a baixas temperaturas (Cryo-SEM). No quarto capítulo, são apresentados os estudos relativos à preparação e caracterização de filmes bionanocompósitos utilizando quitosano como matriz. Primeiramente é apresentada uma revisão sobre filmes de bionanocompósitos e os aspectos fundamentais das técnicas de caracterização utilizadas. A escolha do plasticizante e da sua concentração são discutidas com base nas propriedades de filmes de quitosano preparados. Em seguida, o efeito da concentração de sílica e dos métodos utilizados para a dispersar na matriz de polissacarídeo, bem como o efeito da modificação da superfície da sílica é avaliado. As características da superfície e as propriedades de barreira, mecânicas e térmicas são discutidas para cada conjunto de filmes preparados antes e após a sua neutralização. Os resultados obtidos mostraram que a dispersão das cargas no plasticizante e posterior adição à matriz polissacarídica resultaram apenas em pequenas melhorias já que o problema da agregação de sílica não foi ultrapassado. Por esse motivo foram preparados filmes com SiO2@APS os quais apresentaram propriedades melhores apesar da agregação das partículas não ter sido completamente impedida. Tal pode estar relacionado com o processo de secagem dos filmes. Finalmente, no capítulo 5, são apresentadas as principais conclusões obtidas e algumas sugestões para trabalho futuro.

Investigation of the effect of organics on the water uptake of marine aerosols

Water uptake refers to the ability of atmospheric particles to take up water vapour from the surrounding atmosphere. This is an important property that affects particle size and phase and therefore influences many characteristics of aerosols relevant to air quality and climate. However, the water uptake properties of many important atmospheric aerosol systems, including those related to the oceans, are still not fully understood. Therefore, the primary aim of this PhD research program was to investigate the water uptake properties of marine aerosols. In particular, the effect of organics on marine aerosol water uptake was investigated. Field campaigns were conducted at remote coastal sites on the east coast of Australia (Agnes Water; March-April 2007) and west coast of Ireland (Mace Head; June 2007), and laboratory measurements were performed on bubble-generated sea spray aerosols. A combined Volatility-Hygroscopicity-Tandem Differential Mobility Analyser (VH-TDMA) was employed in all experiments. This system probes the changes in the hygroscopic properties of nanoparticles as volatile organic components are progressively evaporated. It also allows particle composition to be inferred from combined volatility-hygroscopicity measurements. Frequent new particle formation and growth events were observed during the Agnes Water campaign. The VH-TDMA was used to investigate freshly nucleated particles (17-22.5 nm) and it was found that the condensation of sulphate and/or organic vapours was responsible for driving particle growth during the events. Aitken mode particles (~40 nm) were also measured with the VH-TDMA. In 3 out of 18 VH-TDMA scans evaporation of a volatile, organic component caused a very large increase in hygroscopicity that could only be explained by an increase in the absolute water uptake of the particle residuals, and not merely an increase in their relative hygroscopicity. This indicated the presence of organic components that were suppressing the hygroscopic growth of mixed particles on the timescale of humidification in the VH-TDMA (6.5 secs). It was suggested that the suppression of water uptake was caused by either a reduced rate of hygroscopic growth due to the presence of organic films, or organic-inorganic interactions in solution droplets that had a negative effect on hygroscopicity. Mixed organic-inorganic particles were rarely observed by the VH-TDMA during the summer campaign conducted at Mace Head. The majority of particles below 100 nm in clean, marine air appeared to be sulphates neutralised to varying degrees by ammonia. On one unique day, 26 June 2007, particularly large concentrations of sulphate aerosol were observed and identified as volcanic emissions from Iceland. The degree of neutralisation of the sulphate aerosol by ammonia was calculated by the VH-TDMA and found to compare well with the same quantity measured by an aerosol mass spectrometer. This was an important verification of the VH-TMDA‘s ability to identify ammoniated sulphate aerosols based on the simultaneous measurement of aerosol volatility and hygroscopicity. A series of measurements were also conducted on sea spray aerosols generated from Moreton Bay seawater samples in a laboratory-based bubble chamber. Accumulation mode sea spray particles (38-173 nm) were found to contain only a minor organic fraction (< 10%) that had little effect on particle hygroscopicity. These results are important because previous studies have observed that accumulation mode sea spray particles are predominantly organic (~80% organic mass fraction). The work presented here suggests that this is not always the case, and that there may be currently unknown factors that are controlling the transfer of organics to the aerosol phase during the bubble bursting process. Taken together, the results of this research program have significantly improved our understanding of organic-containing marine aerosols and the way they interact with water vapour in the atmosphere.

Stimulation of osteogenic and angiogenic ability of cells on polymers by pulsed laser deposition of uniform akermanite-glass nanolayer

Polymer biomaterials have been widely used for bone replacement/regeneration because of their unique mechanical properties and workability. Their inherent low bioactivity makes them lack osseointegration with host bone tissue. For this reason, bioactive inorganic particles have been always incorporated into the matrix of polymers to improve their bioactivity. However, mixing inorganic particles with polymers always results in inhomogeneity of particle distribution in polymer matrix with limited bioactivity. This study sets out to apply the pulsed laser deposition (PLD) technique to prepare uniform akermanite (Ca2MgSi2O7, AKT) glass nanocoatings on the surface of two polymers (non-degradable polysulfone (PSU) and degradable polylactic acid (PDLLA)) in order to improve their surface osteogenic and angiogenic activity. The results show that a uniform nanolayer composed of amorphous AKT particles (∼30nm) of thickness 130nm forms on the surface of both PSU and PDLLA films with the PLD technique. The prepared AKT-PSU and AKT-PDLLA films significantly improved the surface roughness, hydrophilicity, hardness and apatite mineralization, compared with pure PSU and PDLLA, respectively. The prepared AKT nanocoatings distinctively enhance the alkaline phosphate (ALP) activity and bone-related gene expression (ALP, OCN, OPN and Col I) of bone-forming cells on both PSU and PDLLA films. Furthermore, AKT nanocoatings on two polymers improve the attachment, proliferation, VEGF secretion and expression of proangiogenic factors and their receptors of human umbilical vein endothelial cells (HUVEC). The results suggest that PLD-prepared bioceramic nanocoatings are very useful for enhancing the physicochemical, osteogenic and angiogenic properties of both degradable and non-degradable polymers for application in bone replacement/regeneration.

骨固定用聚乳酸/无机纳米粒子复合材料

本论文针对目前用于骨固定和骨修复的聚乳酸／无机纳米粒子复合材料的界面强度低、粒子分散不均匀以及所采用生物活性无机填料粒径较大等缺点，对轻基磷灰石及生物活性玻璃无机纳米粒子的制备、界面改性、粒子的分散、以及复合材料的制备进行了较详细的论述。另外，对材料的力学性能、结晶性能和生物相容性进行了较细统的测试和研究。（1）以磷酸和氢氧化钙为原料在40-80℃的反应条件下制备出了米粒状和棒状的HAP粒子，然后在-50℃的冷冻干燥机中干燥48h，得到白色的HAP粉末。用TEM、SEM、WAXD、FTIR等对所得产物进行了表征。研究结果表明，提高反应温度有利于生成高结晶度的长棒状HAP颗粒。此外，锻烧温度对粒子的形貌和结晶度也有很大的影响，锻烧温度越高，粒子的结晶度就越高，并且，当锻烧温度提高到900℃以上时，HAP粒子的形貌会由长棒形逐渐变成球形。（2）在高纯氢气气氛中，以辛酸亚锡为催化剂的反应条件下使左旋丙交酷开环聚合，直接接枝到HAP的表面，使HAP的粒子表面覆盖一层聚乳酸分子，使HAP的亲油性能得到提高。对表面接枝的轻基磷灰石（g-HAP）用31PMAS-NMR、FTIR、TGA、TEM、SEM和GPC进行了表征。结果表明，用此方法可在HAP表面接枝6％的PLLA。（3）用溶剂法制备了PLLA/g-HAP复合材料，并对其机械性能、结晶性能和生物相容性进行了表征。试验结果表明：与纯HAP相比，g-HAP粒子更容易均匀分散到PLLA基体中，当填料含量达到4％时，PLLAg-HAP复合材料的力学性能达到最好。由Dsc和PoM的实验结果表明，g-HAP粒子在聚合物基体中可以起到异相成核剂的作用。细胞实验结果表明，PLL刀g-HAP复合材料的细胞相容性明显优于纯的PLLA和PLLA/HAP复合材料。（4）以正硅酸乙酷（TEOS）、硝酸钙（Ca(NO3）2）和磷酸氢二按（（NH4）ZHPO4）为原料，利用在酸性溶液中水解，碱性溶液中缩聚沉淀，然后将反应液离心分离，冷冻干燥，最后在马弗炉中锻烧的方法，得到白色的5102-coo-PZos三元生物活性玻璃粉末。SEM和TEM分析结果表明，所得到生物活性玻璃是粒径在40nln左右的球形颗粒，且粒径分布非常均匀。（5）以正硅酸乙酷（TEoS）和硝酸钙（Ca（NO3）2）为原料，利用在酸性溶液中水解，碱性溶液中缩聚沉淀，然后将反应液离心分离，冷冻干燥，最后在马弗炉中锻烧的方法，得到粒径为200nm左右的球形SiO2-CaO二元生物活性玻璃粉末。

Characterization of Y2O3 : Eu coated with polystyrene

The core-shell Y2O3:Eu3+/polystyrene particles was prepared by surface modification with citric acid and emulsion polymerization method of styrene. The DTA curve of coated particles exhibits a small and wide exothermic peak of organic compound around 387 degreesC. The carbonyl stretching vibration band was shifted to low wavenumber in FTIR spectrum and the binding energy of Y3d5/2 was shifted to high-energy band in XPS spectrum. The results of FTIR and XPS show that citric acid was coupled to the particles surface. The hydrophilic surface became amphiphilic by modification of citric acid. So styrene could adsorb on particles surface to form emulsion structure which inorganic core was inside. EDS spectra show that Y2O3:Eu3+ particles were coated uniformly with polystyrene.

Avaliação das propriedades mecânicas e microestrutura de um ionómero de vidro experimental reforçado com nano partículas

Projeto de Pós-Graduação/Dissertação apresentado à Universidade Fernando Pessoa como parte dos requisitos para obtenção do grau de Mestre em Medicina Dentária