Wettability, Shrinkage and Color Changes of Araucaria angustifolia After Heating Treatment

The effects of thermal treatment on the wettability and shrink resistance of Araucaria angustifolia (Parana pine) were studied from 20 to 200 °C. The contact angles of water droplets on untreated and heat-treated samples were measured by the sessile drop method in the grain of heartwood and sapwood cut in the radial, longitudinal, and tangential directions. A significant increase of the contact angles was verified for the samples from room temperature to 120 °C, in particular in the radial and tangential directions; at higher temperatures, the contact angles assumed almost constant values. From 120 to 200 °C, the sapwood of Araucaria angustifolia showed better dimensional stability and lower thermal resistance when compared to the heartwood. Variations of color were also studied by using the CIELab system, which showed to be capable of accurately distinguishing samples treated at different temperatures.

Densification of Mn-doped tin oxide films by conventional heating and microwave heating treatment

Mn(II) doped SnO2 thin films used for shielding fluoride glasses against corrosion were investigated by x-ray absorption spectroscopy (EXAFS and XANE)S at the Sn and Mn K-edges. The effect of firing treatment on the densification of the films was studied. It has been evidenced a partial change of Mn valence from 2.3 to 2.6 upon heating which is attributed to a change of ratios of two Mn sites: grafted divalent Mn ions at the surface of SnO 2 nanocrystallites and trivalent Mn ions embedded into a substitutional solid solution with Sn. © Physica Scripta 2005.

Interference of heating on the antimicrobial activity and chemical composition of Origanum vulgare L. (Lamiaceae) essential oil

Origanum vulgare L. (oregano), Lamiaceae, essential oil has a variety of biological properties and its antimicrobial activity has received a renewed interest for use in food conservation. The aim of this study was to evaluate the interference of heating on the antimicrobial activity and chemical composition of O. vulgare essential oil. The antimicrobial activity of the essential oil kept at room temperature and exposed to different heating temperatures (60, 80, 100 and 120 °C during 1 hour) was evaluated by observing antimicrobial effectiveness at absolute concentration and determining MIC values by the solid medium diffusion procedure. The essential oil chemical composition analysis was performed by GC-MS. O. vulgare essential oil showed interesting antimicrobial activity on all assayed microbial strains (Candida albicans, C.krusei, C. tropicalis, Bacillus cereus, Escherichia coli, Staphylococcus aureus, Yersinia enterocolitica, Salmonella enterica, Serratia marcencens), noted by large growth inhibition zones (30-42 mm). Heating treatment showed no significant interference (p < 0.05) on the essential oil antimicrobial activity, noted by the development of microbial growth inhibition zones with similar or close diameters when evaluating the essential oil kept at room temperature and after exposure to different thermal treatments. MIC values oscillated between 10and 40 µL.mL-1 (20µL.mL-1 for most strains). However, no significant difference (p < 0.05) was noted among the MIC values found for the essential oil aliquots exposed to different temperatures. Moreover, heating did not significantly (p < 0.05) affect the chemical composition of O. vulgare essential oil. Monoterpenes, terpenic compounds and sesquiterpenes were found in the essential oil, with carvacrol (68.06-70.27%) and p-cymene (12.85-15.81%) being the compounds found in the highest amounts. These results showed the thermal stability and intense antimicrobial properties of O. vulgare essential oil and support its possible concomitant use with heating temperatures in order to reach microbial safety in foods.

Heating effects on physicochemical characteristics and antioxidant activity of flaxseed hull oil (Linum usitatissimum L)

The aim of this study was to analyze the effects of heating on some quality characteristics and antioxidant activity of flaxseed hull oil. Polyunsaturated fatty acids (PUFA) and Cox value decreased during heating. Heating process led to considerable increase in saponification value (SV), peroxide value (PV), p-anisidine value (p-AnV), oxidative value (OV) and specific extinction at 232 and 270 nm. There was a significant decrease in oil stability during heating process (1.4-1.0 h). Fuel properties of flaxseed hull oil were also changed after heating treatment. Heating process caused loss of total phenolic acids, total flavanoids, carotenoids and chlorophyll pigments. Phospholipids (PL) content were less changed compared to other bioactive compounds. Antioxidant activity of flaxseed hull oil decreased during heating process.

How can micelle systems be rebuilt by a heating process?

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Design of bio-based supramolecular structures through self-assembly of α-lactalbumin and lysozyme

Bovine α-lactalbumin (α-La) and lysozyme (Lys), two globular proteins with highly homologous tertiary structures and opposite isoelectric points, were used to produce bio-based supramolecular structures under various pH values (3, 7 and 11), temperatures (25, 50 and 75 °C) and times (15, 25 and 35 min) of heating. Isothermal titration calorimetry experiments showed protein interactions and demonstrated that structures were obtained from the mixture of α-La/Lys in molar ratio of 0.546. Structures were characterized in terms of morphology by transmission electron microscopy (TEM) and dynamic light scattering (DLS), conformational structure by circular dichroism and intrinsic fluorescence spectroscopy and stability by DLS. Results have shown that protein conformational structure and intermolecular interactions are controlled by the physicochemical conditions applied. The increase of heating temperature led to a significant decrease in size and polydispersity (PDI) of α-La–Lys supramolecular structures, while the increase of heating time, particularly at temperatures above 50 °C, promoted a significant increase in size and PDI. At pH 7 supramolecular structures were obtained at microscale – confirmed by optical microscopy – displaying also a high PDI (i.e. > 0.4). The minimum size and PDI (61 ± 2.3 nm and 0.14 ± 0.03, respectively) were produced at pH 11 for a heating treatment of 75 °C for 15 min, thus suggesting that these conditions could be considered as critical for supramolecular structure formation. Its size and morphology were confirmed by TEM showing a well-defined spherical form. Structures at these conditions showed to be stable at least for 30 or 90 days, when stored at 25 or 4 °C, respectively. Hence, α-La–Lys supramolecular structures showed properties that indicate that they are a promising delivery system for food and pharmaceutical applications.

Esterificação de ácidos graxos utilizando zircônia sulfatada e compósitos carvão ativado/zircônia sulfatada como catalisadores

In this work sulfated zirconia (SZr) and activated carbon/SZr composites produced by impregnation method with or without heating treatment step (CABC/SZr-I and CABC/SZr-I SC) and by the method of synthesis of SZr on the carbon (CABC/SZr-S) was used as catalysts in the esterification reactions of fatty acids. The SZr presented very active, conversions higher than 90% were obtained after 2 h of reaction. The activity of the composite CABC/SZr-I20%SC was up to 92%, however, this was directly related to time and temperature reactions. CABC/SZr-I and CABC/SZr-S were less active in esterification reactions, what could be attributed to its low acidity

Análise in vitro da atividade antifúngica e de toxicidade da anfotericina B pré-aquecida

The aim of this work was to evaluate how an aqueous micellar system containing Amphotericin B (AmB) and sodium deoxycholate (DOC) can be rebuilt after heating treatment. Also a review of the literature about the new physicochemical and biological properties of this new system was carried out. Afterwards, heated (AmB-DOC-H) and unheated (AmB-DOC) micelles were subsequently diluted at four different concentrations (50mg.L-1, 5mg.L-1, 0.5mg.L-1 and 0.05mg.L-1) to perform the physicochemical study and, then, the pharmacotoxicity assay, in which two cell models were used for the in vitro experiments, Red Blood Cells (RBC) from human donors and Candida parapisilosis (Cp). While potassium (K+) and hemoglobin leakage from RBC were the used parameters to evaluate the acute and chronic toxicity, respectively, the efficacy of AmB-DOC and AmB-DOC-H were assessed by K+ leakage and cell survival rate from Cp. The spectral study revealed a slight change on the aggregate peak from 327nm to 323nm for AmB-DOC-H compared to AmB-DOC. Concerning the toxicity, although AmB-DOC and AmB-DOC-H presented different behavior for hemoglobin leakage, AmB-DOC produced higher leakage than AmB-DOC-H at high concentrations (from 5mg.L-1) with values tending to zero. However, concerning K+ leakage, both AmB-DOC and AmB-DOC-H, showed similar profile for both cell models, RBC and Cp (p<0,05). AmB-DOC-H and AmB-DOC also revealed similar profile of activity against Cp with equivalent survival rate. In short, the AmB-DOC-H showed much less toxicity than AmB-DOC, but remained as active as the late one against fungal cell. Therefore, the results highlight the importance of this new procedure as a simple, inexpensive and safe alternative to produce a new kind of micelle system for treatment of systemic fungal infections

Caracterização de cerâmicas porosas de alumina reforçada com zircônia produzidas pelo método da réplica

Porous ceramics have many applications: thermal insulation, catalytic support, materials to fire protection, filters, and others. There are many techniques to production of ceramic filters. One technique to obtain ceramic filters is the replication method. This method consists in the impregnation of polymeric foam with ceramic slurry followed by a heating treatment that will burn out the organic elements and sintering of the material, resulting of a replication of the original foam. To perform their functions ceramic filters must satisfy mechanical requirements and permeability parameters (darcian k1 and no-darcian k2). The permeability and the strength of the ceramic material are dependent of the pore size and pore distribution. To the use at high temperatures the evaluation of mechanical properties in these temperatures is necessary. In this work the mechanical behavior of two commercial porous ceramics (10 and 40 poros per inch) was studied these materials were submitted to compression and four-point flexure test (room temperature, at 1000 °C, after thermal shock). Density and porosity measurements, permeability tests and microstructural analysis by scanning electronic microscopy (SEM) were realized. The Results showed that the decrease of mechanical strength of these materials, when submitted to thermal shock, occur for propagation of new cracks from cracks pre-existing and the permeability depends of the pore size

Nanopore size growth and ultrafiltration performance of SnO2 ceramic membranes prepared by sol-gel route

Supported ceramic membranes have been produced by the sol-casting procedure from aqueous colloidal suspensions prepared by the sol-gel route. Coatings on a tubular alumina support have been successfully performed leading to crack free layers. Samples have been sintered at 400, 500 and 600 degreesC, and the effect of heating treatment on the nanostructure and on the ultrafiltration properties are analyzed. The characterization has been done by high resolution scanning electron microscopy, nitrogen adsorption-desorption isotherms, water permeation and cut-off determination using polyethylene glycol standard solutions. The micrographs have revealed that grains and pore size increase with the temperature, whereas their shape remains invariant. This results is in agreements with N-2 adsorption-desorption analyses, which have revealed that the mean pore size diameter increases from 4 to 10 nm as the sintering temperature increases from 400 to 600 degreesC, while the total porosity remains constant. Furthermore, the tortuosity, calculated from water permeability, is essentially invariant with the sintering temperatures. The membranes cut-off, determined with a retention rate equal to 95%, are 3500, 6500 and 9000 g . mol(-1) for 400, 500 and 600 degreesC, respectively, showing that the permeation properties of SnO2 ultrafiltration membranes can easily be controlled by sintering condition.

Modifications induced by acetylacetone in properties of sol-gel derived Y3Al5O12:Tb3+ - I: Structural and morphological organizations

Acetylacetone has been used as a chemical modifier for the synthesis of undoped and Tb3+-doped Y3Al5O12 powders. A systematic investigation concerning its influence on the structural and morphological properties of amorphous and crystallized samples has been carried out. These properties have been comparatively studied by means of X-ray diffraction, infrared spectroscopy, SEM, XAS and SAXS. 27Al NMR and EPR experiments have been performed to complete the study. The combined results have evidenced that acetylacetone promotes organic groups departure during calcination, entailing a better structural organization at lower temperatures compared with unmodified powders. Structuration has been proven to occur at short-scale range until a 600°C heating treatment before being extended by coalescence at higher temperatures. Finally, the presence of acac ligands on the alkoxides leads to a monomer-cluster aggregation process, and thus to a more open network. © 2010 The Royal Society of Chemistry.

Efeito da radiação de microondas sobre Lactobacillus fermentum; linhagens: CCT4143; CCT4144; CCT4145; CCT4146 e FT038B

Pós-graduação em Ciências Biológicas (Microbiologia Aplicada) - IBRC

Síntese e caracterização de compostos HoMn1-x(Ni,Co)xO3

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effectiveness inactivation of trypsin inhibitor fron brazilian cultivarof beans (Phaseolus vulgaris L.)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Caracterização de juntas soldadas em PAW e GTAW de chapas finas em aço maraging 300 submetidas a vários reparos

Pós-graduação em Engenharia Mecânica - FEG