Thermal stability of the martensitic transformation of Cu-Al-Ni-Mn-Ti

The development of new shape memory alloys with high martensitic transformation temperature increases the potential for applications. The development and use of these new alloys depends on the stability of the structure during cycling at high temperatures. If it is possible to guarantee that on alloys keeps the structure during cycling, then the alloy can be used because of the shape memory properties. The aim of this work is to obtain a kinetic model of the forward and backward martensitic transformation of two Cu-Al-Ni-Mn-Ti alloys. Differential scanning calorimetry has been performed in order to establish the kinetic stability of the martensite and the beta transformation. (c) 2006 Elsevier B.V. All rights reserved.

Electrochemical Behavior of Cu-9% Al-5% Ni-2% Mn Alloy in Chloride Media

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Third order elastic constants of bcc Cu-Al-Ni

We have measured the changes in the ultrasonic wave velocity, induced by the application of uniaxial stresses in a Cu-Al-Ni single crystal. From these measurements, the complete set of third-order elastic constants has been obtained. The comparison of results for Cu-Al-Ni with available data for other Cu-based alloys has shown that all these alloys exhibit similar anharmonic behavior. By using the measured elastic constants in a Landau expansion for elastic phase transitions, we have been able to give an estimation of the value of a fourth-order elastic constants combination. The experiments have also shown that the application of a stress in the [001] direction, reduces the material resistance to a (110)[110] shear and thus favors the martensitic transition.

Estudo das reações no sistema 'CU'-'AL'-'AG'-'MN'

Pós-graduação em Química - IQ

Electrochemical corrosion behavior of cast Mg-Al-RE-Mn Alloys in NaCl solution

The electrochemical corrosion behavior of Mg-6Al-0.4Mn and Mg-6Al-4RE-0.4Mn (RE = Mischmetal) alloys is investigated in 3.5% NaCl solution. The results of corrosion process, polarization behavior, and electrochemical impedance spectroscopy of the alloys reveal that Mg-6Al-4RE-0.4Mn exhibits enhanced corrosion resistance. The addition of RE stabilizes the solid solution and modifies the passive film through a finer microstructure.

Variáveis térmicas de solidificação, espaçamento dentríticos secundários e resistência à corrosão de ligas hipoeutéticas Al-Ni

No presente trabalho, é realizada uma seqüência de experimentos com ligas hipoeutéticas Al-Ni para analisar a solidificação unidirecional vertical ascendente em condições transitórias de fluxo de calor. Abordagens experimentais são desenvolvidas para a determinação quantitativa de variáveis térmicas de solidificação, tais como: tempos locais de solidificação; velocidades de deslocamento das isotermas liquidus; taxas de resfriamento à frente da isoterma liquidus e gradientes térmicos à frente da interface sólido / líquido. O trabalho analisa também a dependência dos espaçamentos dendríticos secundários em relação às variáveis térmicas de solidificação e ao teor de soluto das ligas, além de relacionar estes parâmetros com a resistência à corrosão destas ligas. Esses parâmetros dendríticos experimentais, referentes à solidificação das ligas Al - 1, 1,4 e 1,8 % Ni, não puderam ser comparados com os principais modelos teóricos de crescimento dendrítico da literatura, pois, para as ligas em estudo há uma escassez de propriedades termofísicas, impossibilitando assim esta comparação. O comportamento corrosivo é analisado pela técnica de polarização potenciodinâmica e técnica de polarização potenciodinâmica cíclica conduzidas em solução de 3,5% NaCl em temperatura ambiente, estruturas dendríticas mais grosseiras tendem a aumentar as taxas de corrosão das ligas hipoeutéticas do sistema Al-Ni. Os resultados experimentais obtidos através de ensaios de corrosão são correlacionados com a microestrutura dendrítica. Dessa forma, são determinadas tendências experimentais de crescimento dendrítico e resistência à corrosão para a solidificação unidirecional vertical ascendente.

On the stability of the bcc phase in Cu-Al-Mn shape memory alloys

Measurements of the entropy change at the martensitic transition of two composition-related sets of Cu-Al-Mn shape-memory alloys are reported. It is found that most of the entropy change has a vibrational origin, and depends only on the particular close-packed structure of the low-temperature phase. Using data from the literature for other Cu-based alloys, this result is shown to be general. In addition, it is shown that the martensitic structure changes from 18R to 2H when the ratio of conduction electrons per atom reaches the same value as the eutectoid point in the equilibrium phase diagram. This finding indicates that the structure of the metastable low-temperature phase is reminiscent of the equilibrium structure.

Disorder-induced critical phenomena in magnetically glassy Cu-Al-Mn alloys

Measurements of magnetic hysteresis loops in Cu-Al-Mn alloys of different Mn content at low temperatures are presented. The loops are smooth and continuous above a certain temperature, but exhibit a magnetization discontinuity below that temperature. Scaling analysis suggest that this system displays a disorder-induced phase transition line. Measurements allow one to determine the critical exponents ß=0.03±0.01 and ß¿=0.4±0.1, which coincide with those reported recently in a different system, thus supporting the existence of universality for disorder-induced critical points.

Martensite decomposition in Cu-Al-Mn-Ag alloys

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Processing maps for hot working of Cu-Ni-Zn alloys. Part I - Alpha-nickel silver

The constitutive behaviour of agr — nickel silver in the temperature range 700–950 °C and strain rate range 0.001–100 s–1 was characterized with the help of a processing map generated on the basis of the principles of the ldquodynamic materials modelrdquo of Prasadet al Using the flow stress data, processing maps showing the variation of the efficiency of power dissipation (given by 2m/(m+1) wherem is the strain-rate sensitivity) with temperature and strain rate were obtained, agr-nickel silver exhibits a single domain at temperatures greater than 750 °C and at strain rates lower than 1s–1, with a maximum efficiency of 38% occurring at about 950 °C and at a strain rate of 0.1 s–1. In the domain the material undergoes dynamic recrystallization (DRX). On the basis of a model, it is shown that the DRX is controlled by the rate of interface formation (nucleation) which depends on the diffusion-controlled process of thermal recovery by climb. At high strain rates (10 and 100s–1) the material undergoes microstructural instabilities, the manifestations of which are in the form of adiabatic shear bands and strain markings.