Electrodeposition of copper on titanium wires: Taguchi experimental design approach

Electrodeposition of thin copper layer was carried out on titanium wires in acidic sulphate bath. The influence of titanium surface preparation, cathodic current density, copper sulphate and sulphuric acid concentrations, electrical charge density and stirring of the solution on the adhesion of the electrodeposits was studied using the Taguchi statistical method. A L(16) orthogonal array with the six factors of control at two levels each and three interactions was employed. The analysis of variance of the mean adhesion response and signal-to-noise ratio showed the great influence of cathodic current density on adhesion. on the contrary, the other factors as well as the three investigated interactions revealed low or no significant effect. From this study optimized electrolysis conditions were defined. The copper electrocoating improved the electrical conductivity of the titanium wire. This shows that copper electrocoated titanium wires could be employed for both electrical purpose and mechanical reinforcement in superconducting magnets. (C) 2008 Elsevier B.V. All rights reserved.

Assessment of the effectiveness of steel fibre reinforcement for the punching resistance of flat slabs by experimental research and design approach

The present paper deals with the experimental assessment of the effectiveness of steel fibre reinforcement in terms of punching resistance of centrically loaded flat slabs, and to the development of an analytical model capable of predicting the punching behaviour of this type of structures. For this purpose, eight slabs of 2550 x 2550 x 150 mm3 dimensions were tested up to failure, by investigating the influence of the content of steel fibres (0, 60, 75 and 90 kg/m3) and concrete strength class (50 and 70 MPa). Two reference slabs without fibre reinforcement, one for each concrete strength class, and one slab for each fibre content and each strength class compose the experimental program. All slabs were flexurally reinforced with a grid of ribbed steel bars in a percentage to assure punching failure mode for the reference slabs. Hooked ends steel fibres provided the unique shear reinforcement. The results have revealed that steel fibres are very effective in converting brittle punching failure into ductile flexural failure, by increasing both the ultimate load and deflection, as long as adequate fibre reinforcement is assured. An analytical model was developed based on the most recent concepts proposed by the fib Mode Code 2010 for predicting the punching resistance of flat slabs and for the characterization of the behaviour of fibre reinforced concrete. The most refined version of this model was capable of predicting the punching resistance of the tested slabs with excellent accuracy and coefficient of variation of about 5%.

A Learner-Centred Game-Design Approach: Impacts on teachers" creativity

This study presents an innovative pedagogical approach where teachers become game designers and engage in creative teaching practices. Within co-design training workshops, 21 Spanish primary and secondary school teachers have developed their own Game-Based Learning (GBL) scenarios, especially tailored to their teaching contexts and students profiles. In total, teachers developed 13 GBL scenarios and put them into practice in real teaching contexts. The present paper analyses the impacts of this learner-centred game design approach on teachers" creativity from three different points of view: the GBL design process, the GBL scenario, and the teaching processes at stake.

Transferring ownership of public housing to existing tenants: a mechanism design approach

This paper explores situations where tenants in public houses, in a specific neighborhood, are given the legislated right to buy the houses they live in or can choose to remain in their houses and pay the regulated rent. This type of legislation has been passed in many European countries in the last 30-35 years (the U.K. Housing Act 1980 is a leading example). The main objective with this type of legislation is to transfer the ownership of the houses from the public authority to the tenants. To achieve this goal, selling prices of the public houses are typically heavily subsidized. The legislating body then faces a trade-off between achieving the goals of the legislation and allocating the houses efficiently. This paper investigates this specific trade-off and identifies an allocation rule that is individually rational, equilibrium selecting, and group non-manipulable in a restricted preference domain that contains “almost all” preference profiles. In this restricted domain, the identified rule is the equilibrium selecting rule that transfers the maximum number of ownerships from the public authority to the tenants. This rule is preferred to the current U.K. system by both the existing tenants and the public authority. Finally, a dynamic process for finding the outcome of the identified rule, in a finite number of steps, is provided.

The autotelic experience : a design approach to user experience

Si les principes d’utilisabilité guident la conception de solutions de design interactif pour s’assurer que celles-ci soient « utilisables », quels principes guident la conception d’objets interactifs pour s’assurer que l’expérience subjective de l’usager (UX) soit adéquate et mémorable? Que manque-t-il au cadre de l‘UX pour expliquer, comprendre, et anticiper en tant que designer une expérience mémorable (‘an experience’; Dewey, 1934)? La question centrale est issue d’une double problématique : (1) le cadre théorique de l’UX est incomplet, et (2) les processus et capacités des designers ne sont pas considérés et utilisés à leur pleine capacité en conception UX. Pour répondre à cette question, nous proposons de compléter les modèles de l’UX avec la notion d’expérience autotélique qui appartient principalement à deux cadres théoriques ayant bien cerné l’expérience subjective, soit l’expérience optimale (ou Flow) de Csikszentmihalyi (1988) et l’expérience esthétique selon Schaeffer (2001). L’autotélie est une dimension interne du Flow alors qu’elle couvre toute l’expérience esthétique. L’autotélie est une expérience d’éveil au moment même de l’interaction. Cette prise de conscience est accompagnée d’une imperceptible tension de vouloir faire durer ce moment pour faire durer le plaisir qu’il génère. Trois études exploratoires ont été faites, s’appuyant sur une analyse faite à partir d’un cadre théorique en trois parties : le Flow, les signes d’activité non verbale (les gestes physiques) et verbale (le discours) ont été évalués pour voir comment ceux-ci s’associent. Nos résultats tendent à prouver que les processus spatiaux jouent un rôle de premier plan dans l’expérience autotélique et par conséquent dans une UX optimale. De plus, ils suggèrent que les expériences pragmatique et autotélique sont ancrées dans un seul et même contenu, et que leur différence tient au type d’attention que le participant porte sur l’interaction, l’attention ordinaire ou de type autotélique. Ces résultats nous ont menés à proposer un modèle pour la conception UX. L’élément nouveau, resté jusqu’alors inaperçu, consiste à s’assurer que l’interface (au sens large) appelle une attitude réceptive à l’inattendu, pour qu’une information puisse déclencher les processus spatiaux, offrant une opportunité de passer de l’attention ordinaire à l’attention autotélique. Le nouveau modèle ouvre la porte à une meilleure valorisation des habiletés et processus du designer au sein de l’équipe multidisciplinaire en conception UX.

On insurance markets with endogenous information acquisition: A robust mechanism design approach

Neste trabalho propomos a aplicação das noções de equilíbrio da recente literatura de desenho de mecanismo robusto com aquisição de informação endógena a um problema de divisão de risco entre dois agentes. Através deste exemplo somos capazes de motivar o uso desta noção de equilíbrio, assim como discutir os efeitos da introdu ção de uma restrição de participação que seja dependente da informação. A simplicidade do modelo nos permite caracterizar a possibilidade de implementar a alocação Pareto efiente em termos do custo de aquisição da informação. Além disso, mostramos que a precisão da informação pode ter um efeito negativo sobre a implementação da alocação efi ciente. Ao final, sao dados dois exemplos específicos de situações nas quais este modelo se aplica.

Electrodeposition of copper on titanium wires: Taguchi experimental design approach

Electrodeposition of thin copper layer was carried out on titanium wires in acidic sulphate bath. The influence of titanium surface preparation, cathodic current density, copper sulphate and sulphuric acid concentrations, electrical charge density and stirring of the solution on the adhesion of the electrodeposits was studied using the Taguchi statistical method. A L(16) orthogonal array with the six factors of control at two levels each and three interactions was employed. The analysis of variance of the mean adhesion response and signal-to-noise ratio showed the great influence of cathodic current density on adhesion. on the contrary, the other factors as well as the three investigated interactions revealed low or no significant effect. From this study optimized electrolysis conditions were defined. The copper electrocoating improved the electrical conductivity of the titanium wire. This shows that copper electrocoated titanium wires could be employed for both electrical purpose and mechanical reinforcement in superconducting magnets. (C) 2008 Elsevier B.V. All rights reserved.

Integrating strategic and sustainable design approach for innovation process: a cement case study

Global society and technology have changed the relationships of the market. Quality and cost are not the main aspects of any industrial product. On the other hand, design, innovation and sustainability became significant requirements to company’s competitiveness. In this context, the design approach has shown evolutions, integrating social and environmental aspects beside traditional aspects such as technical and economic. Still, design has been becoming a strategic opportunity for companies, improving their competitiveness and increasing their market share. Thus, this research has analyzed the integration of both the Sustainable Design and Strategic Design Coaching (SDC) method in the making decision activities of companies. A cement company (BQMIL) was assigned as case study, in which the previous results have pointed out the significant hole of those concepts to generate Eco-innovation and Eco-Brand to increase its market share, corroborating the expectative of the design team

A User Centered Design Approach for Patient Interfaces to a Diabetes IT Platform

Improving patient self-management can have a greater impact than improving any clinical treatment (WHO). We propose here a systematic and comprehensive user centered design approach for delivering a technological platform for diabetes disease management. The system was developed under the METABO research project framework, involving patients from 3 different clinical centers in Parma, Modena and Madrid.

A landscape architectural design approach:the restoration of the Angel Tower and the Cloister of the Cathedral of Cuenca.

Este artículo trata de analizar la reciente evolución de los conceptos sobre intervención en el Patrimonio Cultural. Para ello utiliza como modelo el proyecto metodológico aplicado sobre las dos últimas actuaciones efectuadas en la Catedral de Cuenca. La Carta de Atenas, 1931, que estableció las bases de la modernidad sobre las dos trayectorias de espacio y tiempo, concuerdan hoy después de casi un siglo, recuperando su punto de encuentro. El artículo básicamente valora el potencial que los proyectos contemporáneos de intervención en el patrimonio pueden ofrecer cuando estudias su trayectoria en el paisaje. En orden a certificar sus transformaciones desde la actualidad, el singular monumento de la Catedral de Cuenca, utilizado como modelo, nos aporta a través de sus materiales y morfología la memoria secular que nos informa de sus técnicas constructivas y valores sociales. Este modelo abre un diálogo entre teoría y práctica reflejado a través de los trabajos de restauración aplicados. Después de treinta años de experiencia restauradora llevada a cabo por los autores, las dos últimas intervenciones que son minuciosamente expuestas, revelan algunas nuevas estrategias de aplicación en el proyecto de intervención.

An alternative design approach for detached breakwater projects /

Cover title.

Using modeling as a co-design approach in the planning process of new care environments

Current research shows a relationship between healthcare architecture and patient-related Outcomes. The planning and designing of new healthcare environments is a complex process; the needs of the various end-users of the environment must be considered, including the patients, the patients’ significant others, and the staff. The aim of this study was to explore the experiences of healthcare professionals participating in group modelling utilizing system dynamics in the pre-design phase of new healthcare environments. We engaged healthcare professionals in a series of workshops using system dynamics to discuss the planning of healthcare environments in the beginning of a construction, and then interviewed them about their experience. An explorative and qualitative design was used to describe participants’ experiences of participating in the group modelling projects. Participants (n=20) were recruited from a larger intervention study using group modeling and system dynamics in planning and designing projects. The interviews were analysed by qualitative content analysis. Two themes were formed, representing the experiences in the group modeling process: ‘Partaking in the G-M created knowledge and empowerment’and ‘Partaking in the G-M was different from what was expected and required time and skills’. The method can support participants in design teams to focus more on their healthcare organization, their care activities and their aims rather than focusing on detailed layout solutions. This clarification is important when decisions about the design are discussed and prepared and will most likely lead to greater readiness for future building process.