Hydrolysis of acetic anhydride: Non-adiabatic calorimetric determination of kinetics and heat exchange

A simple calorimetric method to estimate both kinetics and heat transfer coefficients using temperature-versus-time data under non-adiabatic conditions is described for the reaction of hydrolysis of acetic anhydride. The methodology is applied to three simple laboratory-scale reactors in a very simple experimental setup that can be easily implemented. The quality of the experimental results was verified by comparing them with literature values and with predicted values obtained by energy balance. The comparison shows that the experimental kinetic parameters do not agree exactly with those reported in the literature, but provide a good agreement between predicted and experimental data of temperature and conversion. The differences observed between the activation energy obtained and the values reported in the literature can be ascribed to differences in anhydride-to-water ratios (anhydride concentrations). (C) 2010 Elsevier Ltd. All rights reserved.

Formation of isopolyoxometallate(VI) anions in the reaction between M(CO)6 (M = W, Mo) and acetic acid: X-ray crystal structure of [W3(μ3-O)2(μ2η2-O2CCH3)6(H2O)3]2[W10O32·solvent

W(CO)6 reacts with a mixture of acetic acid/acetic anhydride to give [W3 (μ3-O)2(μ2η2-O2CCH3)6(H2O)3](CH3CO2)2 (1), which was converted by HClO4 to [W3 (μ3-O)2(μ2η2-O2CCH3)6(H2O)3](ClO4)2 (2). Addition of CH3CO2Na to the above reaction mixture, and prolonged exposure of the solution to air, results in the formation of the WIV/WVI complex salt [W3(μ3-O)2(μ2η2-O2CCH3)6(H2O)3]2[W10O32]·solvent (3). Complex 3 was also prepared by reacting 1 with Na2WO4·2H2O in acetic acid, and it has been characterized by X-ray crystallography. Addition of [CH3(CH2)3]4N(ClO4) to the reaction filtrate remaining after the preparation of [Mo2(μ-O2CCH3)4][from Mo(CO)6, CH3CO2H and (CH3CO)2O], followed by exposure to air, gives ([CH3(CH2)3]4N)2[Mo6O19] (4).

First report on the kinetics of the uncatalyzed esterification of cellulose under homogeneous reaction conditions: a rationale for the effect of carboxylic acid anhydride chain-length on the degree of biopolymer substitution

The kinetics of the homogeneous acylation of microcrystalline cellulose, MCC, with carboxylic acid anhydrides with different acyl chain-length (Nc; ethanoic to hexanoic) in LiCl/N,N-dimethylacetamide have been studied by conductivity measurements from 65 to 85 A degrees C. We have employed cyclohexylmethanol, CHM, and trans-1,2-cyclohexanediol, CHD, as model compounds for the hydroxyl groups of the anhydroglucose unit of cellulose. The ratios of rate constants of acylation of primary (CHM; Prim-OH) and secondary (CHD; Sec-OH) groups have been employed, after correction, in order to split the overall rate constants of the reaction of MCC into contributions from the discrete OH groups. For the model compounds, we have found that k((Prim-OH))/k((Sec-OH)) > 1, akin to reactions of cellulose under heterogeneous conditions; this ratio increases as a function of increasing Nc. The overall, and partial rate constants of the acylation of MCC decrease from ethanoic- to butanoic-anhydride and then increase for pentanoic- and hexanoic anhydride, due to subtle changes in- and compensations of the enthalpy and entropy of activation.

Agregação de cadeias de acetatos de celulose em LiCl/DMAc: avaliação via viscosimetria

Celulose de linter foi acetilada, visando obter acetatos de celulose com diferentes Graus de Substituição (GS) em meio homogêneo, usando cloreto de lítio/N,N-dimetilacetamida (LiCl/DMAc) como sistema de solvente, e anidrido acético como reagente acetilante. A agregação entre cadeias de celulose ou acetatos de celulose (GS 0,8, 1,5 e 2,0) em solução foi avaliada através de medidas viscosimétricas. Os resultados mostraram que a formação de agregados no sistema de solvente utilizado (LiCl/DMAc) é diferente para celulose e acetatos, e dependente da temperatura e do GS, no caso dos acetatos. Este trabalho corresponde à primeira etapa de um estudo em que se pretende preparar filmes de acetatos, assim como de acetatos reforçados com celulose, diretamente a partir de soluções destes em LiCl/DMAc. Os resultados apresentados permitem uma escolha melhor embasada do intervalo de concentração mais adequado para preparação de filmes, a partir de soluções de acetatos e celulose nesse sistema de solvente.

Sisal cellulose acetates obtained from heterogeneous reactions

In the present work, cellulose obtained from sisal, which is a source of rapid growth, was used. Cellulose acetates were produced in heterogeneous medium, using acetic anhydride as esterifying agent and iodine as catalyst, to check if the procedure described in the literature for commercial cellulose also is adequate to sisal cellulose. The results indicated that iodine is an excellent catalyst to obtain sisal cellulose acetates, but the reaction is so fast as described in the literature when, instead of sisal, lower average molar weight cellulose (microcrystalline) is used. The crystallinity index (I(c)) of sisal cellulose acetates diminished compared to sisal cellulose, but there was no direct correlation between their degree of substitution (DS) and I(c). Probably acetyl groups were introduced more homogeneously along the short chains of microcrystalline cellulose, when compared to sisal cellulose, and then for microcrystalline cellulose acetates the Ic decreases as DS increases. Using the linear correlation that was found between degree of substitution (DS) and time reaction is possible to control the DS of sisal cellulose acetates, considering a large interval of degrees of substitution (0.3-2.8).

Síntese de derivados de adenina e guanina

Tese de Doutoramento em Ciências (Especialidade em Química)

Regeneroidun selluloosapinnan modifiointi kestämään mikro-organismien toimintaa

Työn tavoitteena oli kehittää mikro-organismeja kestävä suoli eli makkarankuori. Työ suoritettiin modifioimalla regeneroitua selluloosaa. Modifiointiliuoksena käytettiin etikkahapon ja etikkahappoanhydridin seosta, johon lisättiin rikkihappoa katalyytiksi. Työssä etsittiin parasta yhdistelmää, joka koostui modifiointiradannopeudesta, modifiointiliuoskoostumuksesta ja erilaisista modifiointimenetelmistä. Kirjallisuusosassa käsiteltiin yleisesti asetaattikalvoja, niiden valmistusta ja ominaisuuksia. Lisäksi perehdyttiin entsyymin ominaisuuksiin ja toimintaan yleisesti. Entsyymeistä yksi otettiin lähempään tarkasteluun. Kokeissa regeneroitua selluloosaa modifioitiin liuoksessa, jonka koostumusta muunneltiin. Kokeissa oli kolme erilaista modifiointimenetelmää, joissa käytettiin neljää modifiointiliuoskoostumusta ja kolmea modifiointinopeutta. Mittauksissa tutkittiin modifioinnin vaikutusta suoliin verrattuna normaaleihin suoliin. Suolille tehtiin sekä mekaanisia että kemiallisia testejä. Kemiallisista testeistä tärkein oli testi, jossa modifioitu suoli altistettiin mikro-organismille. Tulosten perusteella valittiin paras menetelmä. Työssä havaittiin yhden menetelmän olevan muita paljon parempi. Tällä menetelmällä suoritettiin toistokokeita, jotka varmistivat jo saatuja tuloksia. Liuoskoostumusten välillä ei ollut suuria eroja, mutta kuitenkin niistä yksi osoittautui parhaimmaksi. Nopeutta oli vaikeampi määrittää, mutta siitäkin saatiin määritettyä tietty haarukka, jossa reaktio oli tehokkain.

Ciclização do lapachol induzida por sais de tálio III

This work describes the cyclization of lapachol (1) induced by thallium triacetate (TTA) and thallium trinitrate (TTN) in several solvents using magnetic stirring and under microwave irradiation. alpha-Xyloidone (2) - dehydro-alpha-lapachone - was obtained as the main product in these reactions in 20 75% yield. However, rhinacanthin-A (4) was isolated as main product in a 40% yield, using TTA and acetic anhydride:water (1:1) as solvent, and dehydro-iso-alpha-lapachone (3) in 21% yield, using TTA and dichloromethane as solvent. The reaction time decreased drastically under microwave conditions, but the yields of these reactions were not the expected.

Acilação de Friedel-Crafts do 2-metoxinaftaleno usando o ácido dodecafosfotúngstico suportado em sílica (HPW/SiO2) como catalisador e acetonitrila como solvente

The synthesis of fine chemicals intermediates using Friedel-Crafts acylation is one of the most important methods in chemical technology. In this work, the acylation of 2-methoxynaphthalene with acetic anhydride using a silica-supported dodecatungstophosphoric acid catalyst (HPW/SiO2) and acetonitrila as solvent was studied, showing that this reaction is a feasible alternative to produce intermediaries to replace the current methods of production. The reactions using acetonitrile solvent showed yields greater than or equal to the reactions using traditional solvents such as nitrobenzene and dichloroethane. Finally, the modified Eley-Rideal mechanism was proposed to elucidate the experimental data obtained.

Síntese e hidrólise de azalactonas de Erlenmeyer-Plöchl mediadas por radiação micro-ondas em aparelhos doméstico e dedicado: experimentos de química orgânica para a graduação

This work describes a green chemistry experiment for the synthesis of Erlenmeyer-Plöchl azalactones mediated by microwave irradiation, employing both dedicated and domestic equipment. Hippuric acid was reacted with equimolar amounts of benzaldehyde, p-chloro-benzaldehyde or p-N,N-dimethyl-benzaldehyde in acetic anhydride as the solvent. Acid hydrolysis of obtained 4-benzylidene-2-phenyloxazol-5(4H)-one under microwave and convectional heating afforded Z-α-(benzoylamino)cinnamic acid at a 51-61.5% yield. The UV-Vis molecular spectra of 4-benzylidene-2-phenyloxazol-5(4H)-one and 4-(4'-N,N-dimethylbenzylidene)-2-phenyloxazol-5(4H)-one were obtained in ethanol, CH2Cl2 and DMSO and bathochromic shift was observed for the latter azalactone.

ESTUDO DA GLICOSILAÇÃO DO CICLO-HEXANOL COM DIFERENTES DERIVADOS DE D-GLICOSAMINA E PROMOTORES DE GLICOSILAÇÃO PELO MÉTODO DE KOENIGS-KNORR

We report herein a study on the glycosylation of cyclohexanol with four D-glucosamine-based peracetylated glycosyl chlorides bearing different substituents at C-2 and three glycosylation promoters, silver carbonate, silver triflate and mercury II chloride/mercury II oxide, by the Koenigs-Knorr method. Under the conditions studied, glycosylation was successful only when 3,4,6-tri-O -acetyl-2-deoxy-2-phthalimido-α-D-glucopyranosyl chloride was used as the glycosyl donor, with silver carbonate proving the best promoter. In order to investigate the influence of the nature of the halogen at C-1, we also carried out the glycosylation of cyclohexanol with 3,4,6-tri-O -acetyl-2-deoxy-2-phthalimido-α-D-glucopyranosyl bromide, a more reactive glycosyl donor. As expected, the yield with the bromide derivative was higher with the three promoters and, again, silver carbonate was the most efficient promoter. Finally, to illustrate the well-known efficient procedure for conversion of the phtalimido group at C-2 to the corresponding acetamido group, cyclohexyl 3,4,6-tri-O -acetyl-2-deoxy-2-phtalimido-β-D-glucopyranoside was converted into cyclohexyl 2-deoxy-2-acetamido-β-D-glucopyranoside in two steps, namely, hydrazinolysis of the phtalimido group followed by chemoselective acetylation of the free amino group by treatment with acetic anhydride in methanol, at 77% overall yield.

Some aspects of the chemistry of 1, 3, 4 - Thiadiazolium salts and related compounds

The work described in this thesis has been divided into seven sections. The first section involves the preparation of N'-acyl-N'-arylN- benzothiohydrazides by the acylation of N'-aryl-N-benzothiohydrazides and is followed by a brief discussion of their possible conformation in solution. The second section deals with the preparation of 1,3,4-thiadiazolium salts by the action of perchloric acid/acetic anhydride on N'-acylN'- aryl-N-benzothiohydrazides and also by the reaction of N'-arylN- benzothiohydrazides with nitriles in an acidic medium. The preparation of 2-methylthio-I,3,4-thiadiazolium methosulfate by methylating the corresponding thione is also described. The third section deals with the reaction of 2-phenyl- and 2-methyl-I,3,4-thiadiazolium salts with alcohols in the presence of base. The stability and spectra of these compounds are discussed. Treatment of the 2-methyl-I,3,4-thiadiazolium salt with base was found to give rise to a dimeric anhydrobase and evidence supporting its structure is given. The anhydrobase could be trapped by a variety of acylating and thioacylating agents before dimerization occurred. In the fourth section, the reaction of N'-acyl-N'-aryl-N-benzothiohydrazides with a variety of acid anhydrides is described. These compounds were found to be identical with those obtained by acylating the anhydrobase. The mass spectral fragmentation of these compounds is described and the anomolous product obtained upon thiobenzoylation of 3-methyl-l-phenyl-pyrazal-5-one is also discussed. The fifth section deals with thioacyl derivatives of the anhydrobase which were prepared by the action of phosphorus pentasulfide upon the oxygen analogues and also obtained as the major product of the reaction of thioacetic acid with compounds related to N'-aryl-N-benzothiohydrazides. The mass spectra and p.m.r. spectra of these compounds are discussed. In the sixth section, the reaction of the 2-methylthio-l,3,4- thiadiazolium salt with active methylene compounds to give acyl and diacyl derivatives of the anhydrobase is described. Some aspects of these compounds are discussed. The seventh section describes the synthesis of ncyanine~' type dyes incorporating the l,3,4-thiadiazole ring and their spectra are briefly discussed.

Synthesis and properties of some 4H-1, 3, 4 benzothiadiazines /|nby Darko J. Vukov. -- 260 St. Catharines, Ont. : [s. n.],

The work herein has been divided into five sections. In the first section, a new method of converting N-aroyl- hydrazines to hydrazidic halides is described. The second section deals with the products of reaction of hydrazidic halides with thioacetate ion in acetonitrile at room temperature. A number of new acetylthiohydrazides has been isolated together with corresponding hyclrazidic sulphides. Examination of x-ray data for bis-[~ -(2,6- dibromophenylhydrazono) - benZYl] sulphide revealpd the symmetrical structure as the most probable. In the third section, which consists of the three subsections, the synthesis of the 4H-l,3,4 benzothiadiazine ring system has been extended to 4H-l,3,4 benzothiadiazines with substituents in the 5 and 6-positions. Extension of synthesis also involves 4H-l,3,4 benzothiadiazines with mora than one substituent. Nuclear magnetic resonance spectra of 5 and 6 substituted 4H-l,3,4 benzothiadiazines have been ,. recorded. The section ends with a discussion of the mass spectra of some 4H-l.3,4 benzothiadiazines. In the fourth section, which is divided into two sub- -sections, preparation of 7-nitro substituted 4H-l,3,4 benzothiadiazine from N-thiobenzoyl hydrazine and2,4-dinitro -fluorobenzene is found to be satisfactory. Thiohydrazides react with acetic anhydride, in some cases, to give products identical with acetylthiohydrazides obtained from the hydrazidic halides with thioacetate ion at room temperature. In most of the cases thiohydrazides are found to give anomalous products on reaction with acetic anhydride and mechanisms for their formation are discussed. In the fifth section, which forms three subsections, the 4H-l,3,4 benzothiadiazine ring system with a halogen substituent in the 7-position undergoes electrophilic attack preferentially in 5-posi tion. \fuen the 5-posi tion is occupied by a halogen atom, electrophilic substitution occurs at the 7-position of 4H-l,3,4 benzothiadiazine ring system. Substitution at the 4-nitrogen atom in 4H w l,3,4 benzo- -thiadiazine is extremely slow, probably due to delocalisa- -tion of the nitrogen lone pair in the system. Oxidation of 4H-l,3,4 benzothiadiazines occurs at the sulphur atom under relatively mild conditions. t The Appendix deals with the reaction of N-benzoyl-N - -(2,5-dibromophenyl)hydrazine with p-nitrothiophenol~ The proposed p-nitrothiophenoxy - intermediate may undergo benzothiadiazine formation in a proton exchange system.

Detection and quantification of staphylococcus aureus enterotoxin B in food product using isotopic dilution techniques and mass spectrometry

L’entérotoxine B staphylococcique (SEB) est une toxine entérique hautement résistante à la chaleur et est responsable de plus de 50 % des cas d’intoxication d’origine alimentaire par une entérotoxine. L’objectif principal de ce projet de maîtrise est de développer et valider une méthode basée sur des nouvelles stratégies analytiques permettant la détection et la quantification de SEB dans les matrices alimentaires. Une carte de peptides tryptiques a été produite et 3 peptides tryptiques spécifiques ont été sélectionnés pour servir de peptides témoins à partir des 9 fragments protéolytiques identifiés (couverture de 35 % de la séquence). L’anhydride acétique et la forme deutérée furent utilisés afin de synthétiser des peptides standards marqués avec un isotope léger et lourd. La combinaison de mélanges des deux isotopes à des concentrations molaires différentes fut utilisée afin d’établir la linéarité et les résultats ont démontré que les mesures faites par dilution isotopique combinée au CL-SM/SM respectaient les critères généralement reconnus d’épreuves biologiques avec des valeurs de pente près de 1, des valeurs de R2 supérieure à 0,98 et des coefficients de variation (CV%) inférieurs à 8 %. La précision et l’exactitude de la méthode ont été évaluées à l’aide d’échantillons d’homogénat de viande de poulet dans lesquels SEB a été introduite. SEB a été enrichie à 0,2, 1 et 2 pmol/g. Les résultats analytiques révèlent que la méthode procure une plage d’exactitude de 84,9 à 91,1 %. Dans l’ensemble, les résultats présentés dans ce mémoire démontrent que les méthodes protéomiques peuvent être utilisées efficacement pour détecter et quantifier SEB dans les matrices alimentaires. Mots clés : spectrométrie de masse; marquage isotopique; protéomique quantitative; entérotoxines

Effect of acyl chain length on transfection efficiency and toxicity of polyethylenimine

Polyethylenimine (PEI) is an efficient nonviral gene delivery vector because of its high buffering capacity and DNA condensation ability. In our study, the amino groups on the polymeric backbone were acylated using acetic or propionic anhydride to alter the protonation behaviour and the hydrophilic/hydrophobic balance of the polymer. The concentration of acylated primary amines was determined using trinitrobenzene sulphonic acid assay. Results showed that our modified polymers had lower buffering capacities in solutions compared to PEI. The polymers were complexed with plasmid encoding enhanced green fluorescent protein at three different ratios (1:1, 1:2 and 1:10 w/w DNA to polymer) to form polyplexes and their toxicities and transfection efficiencies were evaluated in HEK 293 cells. Acylation reduced the number of primary amines on the polymer and the surface charge, improving haemocompatibility and reducing cytotoxicity. The reduction in the concentration of amino groups helped to optimise DNA compaction and facilitated polyplex dissociation in the cell, which increased transfection efficiency of the modified polymers compared to the parent polymer. Polymers with buffering capacities greater than 50% and less than 80% relative to PEI, showed higher transfection efficiencies than PEI. The propionic anhydride modified polymers had appropriate interactions with DNA which provided both DNA compaction and polyplex dissociation. These systems interacted better with the cell membrane because of their slightly higher lipophilicity and formed polyplexes which were less cytotoxic than polyplexes of acetic anhydride modified polymers. Among the vectors tested, 1:0.3 mol/mol PEI:propionic anhydride in a 1:2 w/w DNA:polymer composition provided the best transfection system with improved transfection efficiency and reduced cytotoxicity.