Parameter optimization of AC rectangular wave outputs for aluminum cold wire GTAW

The objective of this work was to optimize the parameter setup for GTAW of aluminum using an AC rectangular wave output and continuous feeding. A series of welds was carried-out in an industrial joint, with variation of the negative and positive current amplitude, the negative and positive duration time, the travel speed and the feeding speed. Another series was carried out to investigate the isolate effect of the negative duration time and travel speed. Bead geometry aspects were assessed, such as reinforcement, penetration, incomplete fusion and joint wall bridging. The results showed that currents at both polarities are remarkably more significant than the respective duration times. It was also shown that there is a straight relationship between welding speed and feeding speed and this relationship must be followed for obtaining sound beads. A very short positive duration time is enough for arc stability achievement and when the negative duration time is longer than 5 ms its effect on geometry appears. The possibility of optimizing the parameter selection, despite the high inter-correlation amongst them, was demonstrate through a computer program. An approach to reduce the number of variables in this process is also presented.

Morphology and stability of aggregates of an Oxisol according to tillage system and gypsum application

Morphological characterization and aggregate stability is an important factor in evaluating management systems. The aim of this paper is to evaluate the stability and morphology of the aggregates of a dystrophic Oxisol managed with no-tillage and conventional tillage with and without the residual action of gypsum. The experimental design was randomized blocks arranged in split-split plot, where the treatments were two soil management systems (plots) with 0 and 2000 kg ha-1 of gypsum (subplots) and five depths (0-0.05, 0.05-0.10, 0.10-0.15, 0.15-0.20 and 0.20-0.30 m) as the subsubplots, with four replications. The aggregate morphology was determined through images and later evaluated by the Quantporo software. Stability was determined by the wet method. The results showed that the no-tillage system, with or without gypsum residual effect, provided the aggregates with the largest geometric diameters. The combination of no-tillage system and the gypsum residual effect provided rougher aggregates.

Difficulties in access and estimates of public beds in intensive care units in the state of Rio de Janeiro

ABSTRACT OBJECTIVE To estimate the required number of public beds for adults in intensive care units in the state of Rio de Janeiro to meet the existing demand and compare results with recommendations by the Brazilian Ministry of Health. METHODS The study uses a hybrid model combining time series and queuing theory to predict the demand and estimate the number of required beds. Four patient flow scenarios were considered according to bed requests, percentage of abandonments and average length of stay in intensive care unit beds. The results were plotted against Ministry of Health parameters. Data were obtained from the State Regulation Center from 2010 to 2011. RESULTS There were 33,101 medical requests for 268 regulated intensive care unit beds in Rio de Janeiro. With an average length of stay in regulated ICUs of 11.3 days, there would be a need for 595 active beds to ensure system stability and 628 beds to ensure a maximum waiting time of six hours. Deducting current abandonment rates due to clinical improvement (25.8%), these figures fall to 441 and 417. With an average length of stay of 6.5 days, the number of required beds would be 342 and 366, respectively; deducting abandonment rates, 254 and 275. The Brazilian Ministry of Health establishes a parameter of 118 to 353 beds. Although the number of regulated beds is within the recommended range, an increase in beds of 122.0% is required to guarantee system stability and of 134.0% for a maximum waiting time of six hours. CONCLUSIONS Adequate bed estimation must consider reasons for limited timely access and patient flow management in a scenario that associates prioritization of requests with the lowest average length of stay.

Stability of Schistosoma mansoni progeny to antischistosomal drugs

The susceptibility of the MAP Brazilian strain (F1 to F5 progenies) of S. mansoni to four antischistosomal drugs has been reported in a previous study. In the present investigation, progeny F14 of the same strain, was tested for stability to the same 4 drugs. A new medication, Oltipraz (35,972 RP), was added to the study. Five groups of 12 mice infected with cercariae by tail immersion were treated with hycanthone, oxamniquine, niridazole, praziquantel and Oltipraz. An untreated group was used as control. Schistosomal activity was assessed by the localization of worms in the portal vein system, by oogram changes, and percentage of parasite reduction. The stability of the susceptibility of progeny F14 did not change in relation to generations F1 to F5; the progeny was resistant to hycanthone and oxamniquine; but sensitive to niridazole, praziquantel and Oltipraz. We emphasize the importance of the phenomenon of resistance of the worm in view of the fact that oxamniquine has been widely used in Brazilian areas where mansonic schistosomiasis is endemic.

Evaluation of temporal, seasonal and geographic stability of the molluscicidal property of Euphorbia splendens latex

Laboratory tests with aqueous solutions of Euphorbia splendens var. hislopii latex have demonstrated seasonal stability of the molluscicidal principle, with LD90 values of 1.14 ppm (spring), 1.02 ppm (fall), 1.09 ppm (winter), and 1.07 ppm (summer) that have been determined against Biomphalaria tenagophila in the field. Assays on latex collected in Belo Horizonte and Recife yielded LD90 values similar to those obtained with the reference substance collected in Rio de Janeiro (Ilha do Governador), demonstrating geographic stability of the molluscicidal effect. The molluscicidal action of aqueous dilutions of the latex in natura, centrifuged (precipitate) and lyophilized, was stable for up to 124 days at room temperature (in natura) and for up to 736 days in a common refrigerator at 10 to 12ºC (lyophilized product). A 5.0 ppm solution is 100% lethal for snails up to 13 days after preparation, the effect being gradually lost to almost total inactivity by the 30th day. This observation indicated that the active principle is instable. These properties together with the wide distribution of the plant, its resistance and adaptation to the tropical climate, its easy cultivation and the easy obtention of latex and preparation of the molluscicidal solution, make this a promising material for large-scale use in the control of schistosomiasis

Blood culture as a parameter of treatment effectiveness in experimental histoplasmosis of the hamster

The aim of this study was to determine the value of blood culture as a parameter of treatment effectiveness in experimental histoplasmosis. A total of thirty five hamsters, weighing approximately 120g, were inoculated intracardiacly with 0.1 ml of a suspension containing 4 x 10(7) cells/ml of the yeast phase of H. capsulatum. Treatments were started one week after the infection and lasted for 3 weeks. The azoles, (itraconazole, saperconazole and fluconazole) were administered once a day by gavage, at a dose of 8 mg/kg; Amphotericin B was given intraperitonealy every other day at a dose of 6mg/kg. Blood samples (1 ml) were obtained by heart punction from the 4th day after infection and were seeded in Sabouraud honey-agar and BHI-agar. The hamsters that survived were killed one week after treatment completion and the following criteria were considered for treatment evaluation: 1) rate of spontaneous death, at the end of the experience; 2) microscopic examination of Giemsa smears from liver and spleen and 3) determination of CFU in spleen cultures. Amphotericin B was the most effective drug, with negative blood cultures at day 20, negative spleen cultures in all cases and all the animals survived until the end of the study. Fluconazole was the less effective drug, blood cultures were positive during the whole experience, spleen cultures showed a similar average of CFU when compared with the control animals and 42.8% of these animals died. Saperconazole and itraconazole showed a similar activity, with survival of all hamsters and negative blood cultures at 23 and 26 days respectively. Blood culture seems to be valuable parameter for treatments' evaluation in experimental histoplasmosis of the hamster.

Egg excretion in the initial phase of experimental murine schistosomiasis mansoni: stability and association with worm burden

Stability of faecal egg excretion and correlation with results related to worm burden at the initial phase of schistosomiasis mansoni were observed in two groups of mice infected with different Schistosoma mansoni cercarial burdens, by means of analysis of quantitative parasitological studies and schistosome counts after perfusion. Thus, it may be stated that few quantitative parasitological stool examinations could be sufficient to express the infection intensity at the initial phase, on the same grounds that it was already demonstrated at the chronic phase. Furthermore, it is confirmed that the use of the number of eggs passed in the faeces as a tool to estimate the worm burden at the initial phase of schistosome infection is adequate.

Isoenzyme profile as parameter to differentiate pathogenic strains of Entamoeba histolytica in Brazil

The isoenzyme profiles (IP) of 33 strains of Entamoeba histolytica isolated from patients and carriers of two regions in Brazil (Amazonia and Southeast) were determined. The enzymes phosphoglucomutase, glucose-phosphate isomerase, hexokinase and malic enzyme were considered. IP of the strains was correlated with culture conditions, time of maintenance in laboratory and clinical history of patients. The strains were maintained under polyxenic, monoxenic and axenic culture conditions: 27 polyxenic, 1 polyxenic and monoxenic, 1 polyxenic, monoxenic and axenic and 4 axenic only. The patients were symptomatic and asymptomatic. The symptomatic patients presented either non dysenteric (NDC) or dysenteric colitis (DC), associated or not with hepatic abscess (HA). One patient presented anal amoeboma (AM). The analysis of IP for isolates maintained in polyxenic culture showed non pathogenic IP (I) for strains from carriers and patients with NDC, while the strains isolated from patients presenting DC, HA and AM resulted in isolates II or XIX pathogenic IP. This parameter was not able to differentiate strains from carriers from symptomatic patients when these strains were found in axenic or monoxenic culture. All these strains displayed pathogenic IP (II), demonstrating the inability of this parameter to classifying for virulence since it showed identical IP for strains isolated from carriers or symptomatic patients.

Adductor policis muscle: a new anthropometric parameter

PURPOSE: To measure the thickness of adductor pollicis muscle in healthy adults. This measurement will be used as a nutritional anthropometric parameter in further studies. SUBJECTS AND METHOD: Four hundred and twenty-one healthy adults were studied, 209 men and 212 women, with ages ranging from 18 to 87 years, living in Rio de Janeiro. The adductor pollicis muscle was also studied in the human anatomy lab as well as in normal healthy volunteers using CAT scans and nuclear magnetic resonance imaging to ensure that only the adductor pollicis was included in measurement of muscle thickness with a Lange caliper. To standardize the measurement, the methodology was detailed, with subjects sitting with the dominant hand dangling over the homolateral thigh and the elbow bent at approximately a 90° angle. The Lange caliper was applied at a pressure of 10 g/mm², pinching the adductor pollicis muscle at the vertex of an imaginary angle between the thumb and the index finger. The average of 3 consecutive measurements was considered to be the muscle thickness. RESULTS: This study provides the first estimates of adductor pollicis thickness in normal healthy subjects as an anthropometric parameter. The normal values in the dominant hand for men were 12.5 ± 2.8 mm (mean ± SD), median 12 mm, and for women were 10.5 ± 2.3 mm, median 10 mm.

Diversity and stability of fishes (Teleostei) in a temporary river of the Brazilian semiarid region

The effects of hydrological disturbances by flooding and drought on the diversity and stability in a temporary river fish community in the Brazilian semiarid region were analyzed over the 1996 hydrological cycle. Twelve collections of fishes were made during the wet and dry phases, and 789 individuals of 16 species were collected. Diversity was measured using Simpson's Index (S) and community stability was analyzed by the variation in abundance using Kendall's W concordance test. Fish diversity in the Taperoá river was subjected to hydrological disturbances by flooding and drought. During the wet phase the diversity was higher (S = 0.855) than during the dry phase (S = 0.771). The community was considered stable during the whole annual hydrological cycle (W = 0.418 p < 0.001), but a higher stability in the community was found during the dry phase. During the dry phase the number of dominant species was smaller than during the wet phase.

Aging and growth parameter from the Piaractus mesopotamicus (pacu) from the Cuiabá river, Mato Grosso, Brazil

This study has aims to determine the age and to estimate the growth parameters using scales of the species. Individuals of Piaractus mesopotamicus (Holmberg, 1887) used in this study were captured in the commercial fishery conducted in the region, along the year 2006. The model selected to express the growth of the species was the von Bertalanffy Sl= Sl∞*[1-exp-k(t-to)]. To determine if scales are suitable for studying the growth of pacu, we analyzed the relation between standard length (Sl) and the radius of the scales through linear regression. The period of annuli formation was determined analyzing the variations in the marginal increment and evaluating the consistency of the readings through the analysis of the coefficient of variations (CVs) for the average standard lengths of each age (number of rings) observed in the scales. The relationship between Ls of the fish and the radius of the scales showed that scales can be used to study the age and growth of P. mesopotamicus (R= 0.79). CVs were always below 20%, demonstrating the consistency of the readings. Annuli formation occurred in February, probably related to trophic migration that occurs in this month in the region. Equations that represents the growth in length obtained for P. mesopotamicus are Sl=50.00*[1-exp-0.18(t-(-3.00)] for males and Sl=59.23*[1-exp-0.14(t-(-3.36)] for females. The growth parameters obtained in this study were lower compared to other studies previously conducted for the same species and can related to overexploitation that species is submitted by fishing in the region. These values show also that females of pacu attain greater asymptotic length than males that growth faster.

The thermal stability of yellow fever vaccines

The assessment of yellow fever vaccine thermostability both in lyophilized form and after reconstitution were analyzed. Two commercial yellow fever vaccines were assayed for their thermal stability. Vaccines were exposed to test temperatures in the range of 8 (graus) C to 45 (graus) C. Residual infectivity was measured by a plaque assay using Vero cells. The titre values were used in an accelerated degradation test that follows the Arrhenius equation and the minimum immunizing dose was assumed to be 10 (ao cubo) particles forming unit (pfu)/dose. Some of the most relevant results include that (i) regular culture medium show the same degradation pattern of a reconstituted 17D-204 vaccine; (ii) reconstituted YF-17D-204 showed a predictable half life of more than six days if kept at 0 (graus) C; (iii) there are differences in thermostability between different products that are probably due to both presence of stabilizers in the preparation and the modernization in the vaccine production; (iv) it is important to establish a proper correlation between the mouse infectivity test and the plaque assay since the last appears to be more simple, economical, and practical for small laboratories to assess the potency of the vaccine, and (v) the accelerated degradation test appears to be the best procedure to quantify the thermostability of biological products.

Stability of isoenzyme and kinetoplast DNA (k-DNA) patterns in successively cloned Trypanosoma cruzi populations

Four Trypanosoma cruzi strains from zymodermes A, B, C and D were successively clonedon BHI-LIT-agar-blood BLAB). Twenty clones from the first generation (F1), 10 from The second (F2) and 4 from the third (F3) from the strains A138, B147 and C23 were isolated. The D150 strain provied 29 F1 and F2 clones. The strains and clones had their isoenzyme and K-DNA patterns determined. The clones from A138, Bl47 and C231 strains presented isoemzyme and K-DNA patterns identical between thewmselves and their respective parental strains. Therefore showing the homogenety and stability of isoenzyme and K-DNA patterns after successive cloning. The Dl50 strain from zymodeme D (ZD) showed heterogeneity. Twenty-eight out of 29 clones of the first generation were of zymodeme A and only one was of zymodeme C, confirming previous reports that ZD strains consisted of ZA and ZC parasite populations. The only D150 strain clone of zymodeme C showed a K-DNA pattern identical to its parental strain. The remining clones although similar among themselves were different from the parental strain. Thus the T. cruzi strains had either homonogeneus or heterogeneous populations. The clones produced by successive cloning provided genetically homonogeous populations. Their experimental use will make future results more reliable and reproducible.