Technology for sugarcane agroindustry waste reuse as granulated organomineral fertilizer

Aiming to evaluate the use of sugarcane industry waste such as byproducts from vinasse concentration process, it was assessed the organomineral fertilizer BIOFOM (concentrated vinasse, filter cake, boiler ash, soot from chimneys and supplemented with mineral fertilizers). The study included characterization and agronomic potential analysis of a test plant (corn), by noting the differences between mineral fertilizers and BIOFOM fertilization until 45 days after sowing. The technology traditionally used to produce BIOFOM was based on vinasse evaporation with high heat transfer coefficients. It was observed that the technology, which can be formulated according to the needs of any crop, could be used in many cases as mineral fertilizer. Therefore, the use of this organomineral fertilizer reduces waste generation of sugarcane industry.

Rheological and thermophysical properties of blackberry juice

Rheological and thermophysical properties were determined for blackberry juice, which was produced from blackberry fruit at 9.1 ± 0.5 °Brix and density of 1.0334 ± 0.0043 g cm-3. The concentration process was performed using a roto evaporator, under vacuum, to obtain concentrated juice at about 60 °Brix. In order to obtain different concentrations, concentrated juice was diluted with distilled water. Rheological measurements were carried out using a Rheotest 2.1 Searle type rheometer. In the tested ranges, the samples behaved as pseudoplastic fluids, and the Power-Law model was satisfactorily fitted to the experimental data. The friction factor was measured for blackberry juice in laminar flow conditions of pseudoplastic behavior. Thermal conductivity, thermal diffusivity and density of blackberry juice at 9.4 to 58.4 °Brix were determined, in triplicate, at 0.5 to 80.8 °C. Polynomial regression was performed to fit experimental data obtaining a good fit. Both temperature and concentration showed a strong influence on thermophysical properties of blackberry juice. Calculated apparent specific heat values varied from 2.416 to 4.300 kJ.kg-1 °C in the studied interval.

Effect of pectinolitic enzymes on the physical properties of caja-manga (Spondias cytherea Sonn.) pulp

Cajá-manga, also known as golden apple and hog-plum, is an exotic fruit native from Îles de la Société (French Polynesia), which was first introduced in Brazil in 1985. The pulp of ripe fruit was treated with the commercial enzymatic pool and its effect was evaluated in terms of yield, as well as the physical properties viscosity, turbidity and color (L* values). Response surface methodology was used and three levels were adopted for the independent variables temperature (30, 40, and 50 ºC), incubation time (30, 60 and 90 minutes) and enzyme concentration (0.01, 0.05, 0.09 v/v%). A central composite statistical design was used to guide the experimental work. The enzyme treatment highly increased both juice yield (up to 56%) and color (up to 8.6%) and strongly decreased viscosity (up to 57.4%), clarity (up to 77%) and turbidity (up to 85.5%). Incubation time was the most interacting facto, whereas temperature was the least one. Optimization analysis was carried out to reduce enzyme concentration to a minimum by superposing the contour plots of the tested properties, and the recommended ranges of the variables enzyme concentration, process temperature and incubation time were, respectively, 0.042-0.068%, 47.0-49.0 ºC and 82-90 minutes.

The effect of irradiation and thermal process on beef heme iron concentration and color properties

The aim of this study was to evaluate the influence of irradiation and thermal process on the heme iron (heme-Fe) concentration and color properties of Brazilian cattle beef. Beef samples (patties and steaks) were irradiated at 0-10 kGy and cooked in a combination oven at 250 ºC for 9 minutes with 70% humidity. Total iron and heme iron (heme-Fe) concentrations were determined. The data were compared by multiple comparisons and fixed- effects ANOVA. Irradiation at doses higher than 5 kGy significantly altered the heme-Fe concentration. However, the sample preparation conditions interfered more in the heme-Fe content than did the irradiation. Depending on the animal species, meat heme iron levels between 35 and 52% of the total iron are used for dietetic calculations. In this study the percentage of heme-iron was, on average, 70% of the total iron showing that humidity is an important factor for its preservation. The samples were analyzed instrumentally for CIE L*, a*, and b* values.

Cooking process evaluation on mercury content in fish

This study evaluated different cooking processes (roasted, cooked and fried) on total mercury (Hg) content in fish species most consumed by Manaus residents and surrounding communities, Amazon region. The results obtained for total Hg in natura and after the three types of preparation (roasted, cooked and fried) for 12 fish species showed a significant Hg concentration variation. In the present study the cooked and frying processes resulted in higher Hg losses for Pacu, Pescada, Jaraqui, Curimatã, Surubin and Aruanã fish species, most of them presenting detritivorous and carnivorous feeding habits. The higher Hg losses in the roasting process occurred for Sardinha, Aracu, Tucunaré, Pirapitinga, Branquinha and Tambaqui fish species, most of them being omnivorous and herbivorous fish species. Some micronutrients (Ca, Fe, K, Na, Se and Zn) in fish species in natura were also determined in order to perform a nutritional evaluation regarding these micronutrients.

The efficiency of concentration methods used to detect enteric viruses in anaerobically digested sludge

The presence of enteric viruses in biosolids can be underestimated due to the inefficient methods (mainly molecular methods) used to recover the viruses from these matrices. Therefore, the goal of this study was to evaluate the different methods used to recover adenoviruses (AdV), rotavirus species A (RVA), norovirus genogroup II (NoV GII) and the hepatitis A virus (HAV) from biosolid samples at a large urban wastewater treatment plant in Brazil after they had been treated by mesophilic anaerobic digestion. Quantitative polymerase chain reaction (PCR) was used for spiking experiments to compare the detection limits of feasible methods, such as beef extract elution and ultracentrifugation. Tests were performed to detect the inhibition levels and the bacteriophage PP7 was used as an internal control. The results showed that the inhibitors affected the efficiency of the PCR reaction and that beef extract elution is a suitable method for detecting enteric viruses, mainly AdV from biosolid samples. All of the viral groups were detected in the biosolid samples: AdV (90%), RVA, NoV GII (45%) and HAV (18%), indicating the viruses' resistance to the anaerobic treatment process. This is the first study in Brazil to detect the presence of RVA, AdV, NoV GII and HAV in anaerobically digested sludge, highlighting the importance of adequate waste management.

An ethanol-based process to simultaneously extract and fractionate carotenoids from Mauritia flexuosa L. Pulp

Mauritia vinifera (buriti) is a palm tree that grows wild in different areas of Brazil, particularly in the Amazonian region. The buriti oil is rich in carotenoids, especially in β-carotene. The growing interest in other natural sources of β-carotene has stimulated the industrial use of buriti as a raw material for pulp oil extraction. Most processes are based on the conventional technologies, involving drying and pressing the pulp for oil recovery and further separation of carotenoids in a liquid phase using organics solvents. In the present work, the ethanol-based process was evaluated for simultaneous carotenoids recovering and fractionating from buriti pulp. The raw material and ethanol, 1:4 ratio, were placed in an erlenmeyer flask and maintained at 30rpm for 1 hour in a temperature-controlled bath at 65ºC. The mixture was filtered under vacuum and cooling at 10ºC to allow for the separation of the solvent in two phases. Carotenoids composition, determined by HPLC, has indicated a β-carotene concentration about 12 times greater in the lower phase than in the upper phase. The profile of the carotenoids in the denser phase is quite similar to that of raw buriti oil, and the concentration of total carotenoids is 40% higher than that of the original raw oil, making the ethanol-based process particularly attractive for industrial applications.

Determination of sulfate in the wet-process of phosphoric acid by reverse flow injection

An improved method based on reverse flow injection is proposed for determining sulfate concentration in the wet-process of phosphoric acid (WPA). The effect of reagent composition, flow rate, temperature, acid concentration, length of the reaction coil, and linear response range on the flow system is discussed in detail. Optimal conditions are established for determining sulfate in the WPA samples. Baseline drift is avoided by a periodic washing step with EDTA in an alkaline medium. A linear response is observed within a range of 20 - 360 mg L-1, given by the equation A = 0.0020C (mg L-1) + 0.0300, R² = 0.9991. The detection limit of the proposed method for sulfate analysis is 3 mg L-1, and the relative standard deviation (n = 12) of sulfate absorbance peak is less than 1.60%. This method has a rate of up to 29 samples per hour, and the results compare well with those obtained with gravimetric method.

Photo-Fenton process for treating biological laboratory wastewater containing formaldehyde

Laboratories consume great amounts of hazardous chemicals substances and consequently generate wastewater containing them, for example formaldehyde. This substance is widely utilized to preserve biological samples generating many liters of this residue every year. The present work proposes the use of the photo-Fenton process to treat formaldehyde wastewater using sunlight irradiation. Some aspects were investigated such as the iron source, sample and hydrogen peroxide concentration and also the use of stirred systems. The use of ferrioxalate (0.5 mmol L-1) improved the efficiency of the process in relation to the use of iron nitrate, while at least 1.0 mol L-1 H2O2 is necessary to treat the sample of the 500 mg C L-1. Under these conditions, every formaldehyde detectable was degradeted and 89% of the dissolved organic carbon was removed in two hours of exposure to sunlight. These results are satisfaction considerate for São Paulo State Environmental Agency.

Structural basis for the pathophysiology of lipoprotein(a) in the athero-thrombotic process

Lipoprotein Lp(a) is a major and independent genetic risk factor for atherosclerosis and cardiovascular disease. The essential difference between Lp(a) and low density lipoproteins (LDL) is apolipoprotein apo(a), a glycoprotein structurally similar to plasminogen, the precursor of plasmin, the fibrinolytic enzyme. This structural homology endows Lp(a) with the capacity to bind to fibrin and to membrane proteins of endothelial cells and monocytes, and thereby to inhibit plasminogen binding and plasmin generation. The inhibition of plasmin generation and the accumulation of Lp(a) on the surface of fibrin and cell membranes favor fibrin and cholesterol deposition at sites of vascular injury. Moreover, insufficient activation of TGF-ß due to low plasmin activity may result in migration and proliferation of smooth muscle cells into the vascular intima. These mechanisms may constitute the basis of the athero-thrombogenic mode of action of Lp(a). It is currently accepted that this effect of Lp(a) is linked to its concentration in plasma. An inverse relationship between Lp(a) concentration and apo(a) isoform size, which is under genetic control, has been documented. Recently, it has been shown that inhibition of plasminogen binding to fibrin by apo(a) is also inversely associated with isoform size. Specific point mutations may also affect the lysine-binding function of apo(a). These results support the existence of functional heterogeneity in apolipoprotein(a) isoforms and suggest that the predictive value of Lp(a) as a risk factor for vascular occlusive disease would depend on the relative concentration of the isoform with the highest affinity for fibrin

The effect of thyroid hormones on the white adipose tissue gene expression of PAI-1 and its serum concentration

Metabolic syndrome is associated with an increased risk of developing cardiovascular diseases and Plasminogen activator inhibitor 1 (PAI-1) overexpression may play a significant role in this process. A positive correlation between adipose tissue gene expression of PAI-1 and its serum concentration has been reported. Furthermore, high serum levels of thyroid hormones (T3 and T4) and PAI-1 have been observed in obese children. The present study evaluates the impact of thyroid hormone treatment on white adipose tissue PAI-1 gene expression and its serum concentration. Male Wistar rats (60 days old) were treated for three weeks with T4 (50 µg/day, Hyper) or with saline (control). Additionally, 3T3-L1 adipocytes were treated for 24 h with T4 (100 nM) or T3 (100 nM). PAI-1 gene expression was determined by real-time PCR, while the serum concentration of PAI-1 was measured by ELISA using a commercial kit (Innovative Research, USA). Both the serum concentration of PAI-1 and mRNA levels were similar between groups in retroperitoneal and epididymal white adipose tissue. Using 3T3-L1 adipocytes, in vitro treatment with T4 and T3 increased the gene expression of PAI-1, suggesting non-genomic and genomic effects, respectively. These results demonstrate that thyroid hormones have different effects in vitro and in vivo on PAI-1 gene expression in adipocytes.

Influence of carbon source and the fermentation process on levan production by Zymomonas mobilis analyzed by the surface response method

The aim of this study is to assess sugar cane juice and sucrose as substrates, the batch and fed batch processes and their interaction in the levan production using a complete factorial design. Zymomonas mobilis was cultivated in different sugar cane juice and sucrose concentrations in two fermentation processes at 25 °C for 20 h. A complete factorial design (2³) was used to analyze the effects of the type and concentration of the substrate, as well as the batch and fed batch processes. A complete second factorial design (2²) was used to observe the importance of sugar cane juice. The results indicated that the batch process improved the levan production reaching 40.14 g/L. The addition of sugar cane juice was not statistically significant for levan formation, however sugar cane juice stimulated biomass, sorbitol and ethanol production. The best medium for levan production was 150 g/L sucrose in batch.

Process variables in the osmotic dehydration of sliced peaches

This paper evaluated the influence of temperature and concentration of the sucrose syrup on the pre-osmotic dehydration of peaches. Physical (colour and texture) and chemical variables (soluble solid content; total sugar, reducing and non-reducing sugar contents; and titratable acidity) were investigated, as well as the osmotic dehydration parameters (loss of weight and water; solids incorporation). An experimental central composite design was employed varying the temperature (from 30 to 50 ºC) and concentration (from 45 to 65 ºBrix) and maintaining the syrup to fruit ratio (4:1), process time (4 hours), and format (slices). The degree of acceptance was used in the sensory analysis evaluating the following characteristics: appearance, taste, texture, colour, and overall quality using a hedonic scale. The results were modelled using the Statistica program (v. 6.0) and the Response Surface Methodology. The mathematical models of the following dimensionless variations yielded significant (p < 0.05) and predictive results: soluble solids content, total and non-reducing sugar contents, titratable acidity, colour parameter L*, and water loss. The models of the attributes colour and appearance yielded significant (p < 0.10) but not predictive results. Temperature was the prevalent effect in the models. The process conditions in the range from 50 to 54.1 ºC and from 45 to 65 ºBrix led to greater water losses and better sensory performances.

Microparticles obtained by complex coacervation: influence of the type of reticulation and the drying process on the release of the core material

Microparticles obtained by complex coacervation were crosslinked with glutaraldehyde or with transglutaminase and dried using freeze drying or spray drying. Moist samples presented Encapsulation Efficiency (%EE) higher than 96%. The mean diameters ranged from 43.7 ± 3.4 to 96.4 ± 10.3 µm for moist samples, from 38.1 ± 5.36 to 65.2 ± 16.1 µm for dried samples, and from 62.5 ± 7.5 to 106.9 ± 26.1 µm for rehydrated microparticles. The integrity of the particles without crosslinking was maintained when freeze drying was used. After spray drying, only crosslinked samples were able to maintain the wall integrity. Microparticles had a round shape and in the case of dried samples rugged walls apparently without cracks were observed. Core distribution inside the particles was multinuclear and homogeneous and core release was evaluated using anhydrous ethanol. Moist particles crosslinked with glutaraldehyde at the concentration of 1.0 mM.g-1 protein (ptn), were more efficient with respect to the core retention compared to 0.1 mM.g-1 ptn or those crosslinked with transglutaminase (10 U.g-1 ptn). The drying processes had a strong influence on the core release profile reducing the amount released to all dry samples

Acid and salt uptake during the marinatig process of Engraulis anchoita fillets influence of the solution: fish ratio and agitation

The aims of this research were to determine the effect of different conditions of the marination stage on the salt and acid uptake, immersion time, and sensorial characteristics during the marinating process of anchovy (Engraulis anchoita). Different solution:fish ratios and the agitation effect during this stage were analyzed. The ratios used were: 0.77:1, 3:1 and 10:1 (with and without agitation). An increase of marinating solution:fish ratio causes a higher speed of acid and salt penetration The product obtained with the 10:1 ratio had a dry and fibrous texture and a slightly salty taste. Salt concentration was statistically significantly lower (p < 0.01) in the samples with agitation. Agitation did not influence the acid uptake, and the salt penetration speed decreased, but rancidity was detected in this product. The ratio 3:1 decreases the marinating time without damaging sensory attributes and can be used in the fish marinating process.