Estudo do efeito do tratamento superficial por moagem sobre as propriedades das partículas de uma liga de hidreto metálico

This work reports results of studies on the electrochemical and structural properties of a Ti/Zr-based metal hydride alloy covered by Ni and LaNi4,7Sn0,3 powder additives by ball milling. The effect of this treatment is investigated for the activation time, hydrogen storage capacity and equilibrium pressure, cycling stability and the hydration/dehydration kinetics. Charge and discharge cycles show a significant decrease of the activation time due to an increase of the active area caused by the milling treatment, independent of the additive. However, other results have evidenced little effect of the milling surface treatment on the charge storage capacity, hydrogen equilibrium pressure, and hydration/dehydration kinetics, for both the Ni and LaNi4,7Sn0,3 covered materials.

Análise cristalográfica da solução sólida com estrutura tipo Tungstênio Bronze de niobato de potássio e estrôncio dopado com ferro

Solid solution of iron doped potassium strontium niobate with KSr2(FeNb4)O15-Δ stoichiometry was prepared by high efficiency ball milling method. Structural characterization was carried out by X-ray diffraction. Crystalline structure was analyzed by the Rietveld refinements using the FullProf software. The results showed a tetragonal system with the tetragonal tungsten bronze structure - TTB (a = 12.4631 (2) Å and c = 3.9322 (6) Å, V = 610.78 (2) ų). In this work, the sites occupancy by the K+, Sr2+ and Fe3+ cations on the TTB structure were determined. NbO6 polihedra distortion and its correlation with the theoretical polarization are discussed.

Efeito da ativação mecânica de uma formulação de talco/caulim/alumina sobre o mecanismo e a cinética de formação de cordierita

In this study, the influence of mechanical activation by intensive ball milling of a stoichiometric mixture of talc, kaolin, and alumina on the mechanism and kinetics of cordierite (2MgO·2Al2O3·5SiO2) formation was evaluated. The raw materials were characterized by chemical analysis, X-ray diffraction (XRD), laser diffraction, and helium pycnometry. The kinetics and mechanism of cordierite formation were studied by XRD, differential thermal analysis, and dilatometry in order to describe the phase formation as a function of temperature (1000-1400 ºC), time of thermochemical treatment (0-4 h), and grinding time of the mixture (0-45 min). Finally, the optimal conditions of the thermochemical treatment that ensured the formation of cordierite were determined: milling time of 45 min and thermal treatment at 1280 ºC for 1 h.

Fungus ball in HIV-infected patients

Aspergillus is a phagocyte opportunistic fungus that causes aspergillosis, an unusual disease in patients with AIDS. Six cases of fungal ball in patients with AIDS are reported here. In this group, all patients had hemoptysis and tuberculosis as the underlying lung disease. The diagnosis of pulmonary fungus ball was based on the clinical and radiographic feature, combined with serological and mycological evidence of Aspergillus fumigatus.

Aspergillus fumigatus fungus ball in hospitalized patients with chronic pulmonary disease: usefulness of double immunodiffusion test as a screening procedure

Double immunodiffusion (DID) was used as a screening test for the diagnosis of aspergillosis. Three hundred and fifty patients were tested, all of them referred from a specialized chest disease hospital and without a definitive etiological diagnosis. When DID was positive addtional information such as clinical history and radiographic findings were requested and also surgical specimens were obtained whenever possible. Specific precipitin hamds for Aspergillus fumigatus antigen were found in 29 (8.3%) of 350 patients sera. Nineteen (65.5%) of the 29 patients with positive serology were recognized as having a fungus ball by X-rays signs in 17 or by pathological examination in 2 or by both in 8 patients. This two-year prospective study has shown that pulmonary aspergillos is a considerable problem among patiens admitted to a Chest Diseases Hospital, especially in those with pulmonary cavities or bronchiectasis.

Portanus Ball: descrições de dez espécies novas (Hemiptera, Cicadellidae, Xestocephalinae)

The following new species are described and illustrated from Brazil: Portanus vittatus sp. nov. (Paraná), P. castaneus sp. nov. (Rondônia), P. variatus sp. nov. (Rondônia), P. ocellatus sp. nov. (Mato Grosso), P. cinctus sp. nov. (Mato Grosso), P. bimaculatus sp. nov. (Rondônia), P. eliasi sp. nov. (Rondônia), P. marginatus sp. nov. (Paraná), P. maculatus sp. nov. (Paraná) and P. bicornis sp. nov. (Mato Grosso).

Portanus Ball: descrição de uma espécie nova (Hemiptera, Cicadellidae, Xestocephalinae)

Portanus dubius sp. nov. é descrita e ilustrada a partir de espécimens que foram coletados com armadilha Malaise durante um levantamento entomológico no Estado do Paraná, Brasil (PROFAUPAR).

Uma nova espécie de Portanus Ball (Hemiptera, Cicadellidae) do Brasil

Uma nova espécie de Portanus Ball, 1932 é descrita a partir de material coletado nos Estados de Rondônia e Mato Grosso, Brasil. A genitália da fêmea também é descrita.

Diretrizes para a construção de um moinho de bolas para a moagem de sólidos em laboratórios

In this paper, we show the construction of a low-cost, high-quality ball mill for obtaining finely divided powders, with the goal of presenting guidelines for achieving the best results for the milling process. This equipment allows for the adjustment of the size of the mill in order to process different quantities of material. The construction of mechanical and electrical components that provide increased efficiency, the choice of milling medium, and frequent problems experienced with homemade ball mills are discussed.

Physical-chemical characterization and wet milling yield of four maize hybrids

The influence of physical-chemical characteristics of maize grains and lactic acid concentrations on byproduct yields, generated by conventional wet milling, was studied during steeping, for four maize hybrids and two lactic acid concentrations (0.55 and 1.00%). For physical-chemical characterization, grain dimensions (length, thickness, and width) were determined, as well as mass of 100 grains, percentage of floating grains, volumetric mass, and centesimal composition. Statistical differences were found for percentage of floating grains (2.33 to 24.67%), volumetric mass (0.814 to 0.850 kg.L-1), mass of 100 grains (0.033 to 0.037 kg), water content (11.86 to 12.20%), proteins (8.21 to 9.06%), lipids (3.00 to 4.77%), and ashes (1.07 to 1.26%). There were no relationships of wet milling yields with maize appearance and physical-chemical characteristics. The addition of 1.00% lactic acid did not statistically improve byproduct yields; however, it favored separation of the grain components.

Influence of Cutting Conditions on Tool Life, Tool Wear and Surface Finish in the Face Milling Process

The main goal of this work is to study the influence of cutting conditions - cutting speed, feed velocity and feed per tooth - on tool life and surface finish of the workpiece in the face milling of flat surfaces. Aiming to achieve this goal, several milling experiments were carried out with different cutting speeds, feed velocities and feeds per tooth. In the first phase of the experiments, cutting speed was varied without varying feed velocity, which caused a variation in feed per tooth. In the second phase of the experiments, cutting speed and feed velocity were varied in such a way that feed per tooth was kept constant. Tool flank wear and surface roughness of the workpiece were measured as cutting time elapsed. The main conclusions of this work are that a) cutting speed has a strong influence on tool life, regardless of whether feed velocity or feed per tooth varies and b) an increase in surface roughness of the workpiece is not closely related to an increase in wear of the primary cutting edge.

Presence of central nervous system tissues as bovine spongiform encephalopathy specified risk material in Turkish raw meat ball (cig kofte)

Abstract Bovine Spongiform Encephalopathy (BSE) is a virulent disease which may infect by affecting the central nervous system (CNS) tissues in cattle and causes degeneration in nerves. Central nervous system tissues such as brain and spinal cord which are classified as specified risk materials (SRMs) are regarded to be main source of infection. The contamination of the meat with the specific risk materials (SRMs) can occur in phases of slaughter, fragmentation of carcass and processing. This study was conducted in order to investigate the existence of CNS tissues in raw meat ball (cig kofte) which is commonly consumed in the Southeastern Region of Turkey, particularly in Şanlıurfa. For this purpose, 145 samples of raw meat ball were tested. The enzyme-linked immunosorbent assay (ELISA) kits (Ridascreen risk material 10/5, R-biofarm GmbH) which determine glial fibrillary acidic protein (GFAP) as determinant were used. As a result of the analyses, positivity was detected in 21 of totally 145 samples of raw meat ball (14.48%). 6 (4.14%) of the samples gave low level of positivity (≥ 0.1 standard absorbance), 10 (6.90%) gave medium level of positivity (>0.2 standard absorbance) and 5 (3.45%) gave high level of positivity (≥0.5 standard absorbance). As a consequence, meats are contaminated in any phase of both slaughter and meat production even if accidentally. Regarding this matter, necessary measures should be taken and hygiene rules should be applied.

Conservadorismo contábil nas companhias abertas e fechadas brasileiras

Objetiva-se neste artigo identificar a existência de diferenças significativas entre companhias abertas e fechadas brasileiras no nível de conservadorismo de suas demonstrações contábeis. A pesquisa, do tipo exploratória e descritiva, baseia-se em amostra composta por 1.384 empresas-ano, sendo 770 observações referentes a companhias fechadas e 614 a companhias abertas, no período de 2000 a 2004. Utilizou-se o modelo de Ball e Shivakumar (2005) que permite analisar o nível de conservadorismo por meio da reversão dos resultados contábeis. Os resultados obtidos evidenciam que as companhias fechadas apresentam menor probabilidade de reconhecimento oportuno das perdas e, por isso, possuem menor nível de conservadorismo nas demonstrações contábeis em relação às companhias abertas.

Pulmonary cavities colonized by actinomycetes: report of six cases

Six cases of a cavitary pulmonary ball formed by Actinomycetes are reported. They were observed in the state of Bahia, Brazil. All patients complained of cough and hemoptysis and the pathological study showed bronchiectasis and small cavities in the lungs. The lesions contained micro-colonies of Actinomyces, identified by morphology, staining properties and culture in two cases (thioglycolate media). In the six patients the disease was limited to the lungs. In one patient grains were found, within micro-abscesses in the surrounding parenchyma. Probably the invasion occurred due to ulceration of bronchial mucosa that was covered by granulation tissue. The author suggests that as in nocardiosis actinomycosys may have an invasive form, a saprophytic one may and colonize pulmonary cavities.