Characterization of Lubricating Oil Using Ultrasound

This paper presents an ultrasonic method to measure small concentrations of water in lubricating oil. It uses an ultrasonic measurement cell composed by a piezoceramic emitter (5 and 10 MHz), and a large aperture PVDF receiver that eliminates diffraction effects. The propagation velocity, attenuation coefficient and density of several samples of water-in-oil emulsion were measured. The concentrations of water of the samples were in the range of 0 to 5% in volume, and the results showed that these low concentrations can be discriminated within a resolution of 0.2% in the studied range, using the measurement of the propagation velocity.

Influence of leaf retention on cutting propagation of Lavandula dentata L.

Vegetative propagation of lavender offers several advantages over sexual propagation, among them crop homogeneity and yield of higher quality essential oil. However, Lavandula species have been propagated mostly by seeds and are said to be recalcitrant to rooting when propagated by cuttings. During cutting propagation, one of the important variables that influence the rooting capacity of cuttings is the leaf retention. The objective of this work was to evaluate the influence of leaf retention on rooting of L. dentata cuttings. Apical cuttings of L. dentata of 10 cm in length, keeping approximately 1/3, 1/2 or 2/3 of their leaves were planted in commercial substrate Plantmax HT® under intermittent mist. After two months, averages of root number, length of the longest root, root fresh and dry weights, and the survival percentage were evaluated. Root length and fresh weight were statistically greater with 2/3 of leaf retention and when fewer leaves were kept on the cuttings, lower means of root dry weight was observed. Under the conditions applied in this study, greater leaf retention was better for rooting of L. dentata cuttings.

Chemical sterilization in in vitro propagation of Arundina bambusifolia Lindl. and Epidendrum ibaguense Kunth

There is a great demand for simpler and less costly laboratory techniques and for more accessible procedures for orchid breeders who do not have the necessary theoretical basis to use the traditional seed and clone production methods of orchids in vitro. The aim of this study was to assess the use of sodium hypochlorite (NaClO) as a decontaminant in the process of inoculating adult orchid explants of Arundina bambusifolia and Epidendrum ibaguenses. Solutions of NaClO (1.200, 2.400, 3.600, 4.800 and 6.000 mg L-1 - equivalent to 50, 100, 150, 200 and 250 mL L-1 of commercial bleach - CB) were sprayed on the explants (1.0 mL) and the culture medium (GB5), in the presence or absence of activated charcoal (2 g L-1). The explants used were nodal segments of field-grown adult plants. The procedures for inoculating the explants were conducted outside the laminar flow chamber (LFC), except for the control treatment (autoclaved medium and explant inoculation inside the LFC). The best results for fresh weight yield, height and number of shoots were obtained using NaClO in solution at 1.200 mg L-1 (equivalent to 50 mL L-1 commercial bleach) with activated charcoal in the culture medium. Fresh weight figures were 1.10 g/jar for Arundina bambusifolia and 0.16 g/jar for Epidendrum ibaguenses. Spraying the NaClO solutions controls the contamination of the culture medium already inoculated with the explants.

Rooting of hardwood cuttings of Roxo de Valinhos fig (Ficus carica L.) with different propagation strategies

The objective of this study was to evaluate the substrate, cuttings collection time, the position and the cutting depth, and the propagation environment on rooting of 'Purple Valinhos' fig tree cuttings in Southwestern Paraná, Brazil. Two experiments were carried out at UTFPR, Câmpus Dois Vizinhos, with hardwoods cuttings from Roxo de Valinhos fig tree. The first experiment used a randomized block design, in 3 x 3 x 2 factorial (substrate x environment x collection time), with four replications of 10 cuttings per plot. The cuttings were collected in the first fifteen days of July and August. The substrates were sand, soil and the mixture of these [1:1 (v / v)]. The environments used were open sky, tunnel with plastic cover and tunnel with half-shade black net cover. The second experiment used a randomized block design, 2 x 2 x 3 factorial (shoot cutting position x soil cover x shoot cutting depth), with four replications of 12 cuttings per plot. In the factor position, the vertically (0 º inclination) and inclined (45 º inclination) shoot cuttings were evaluated. Soil cover was tested with mulching plastic cover or not. The tested depths were 1/3, 1/2 and 2/3 in relation to the total length of the shoot cutting. In both experiments, the following were analyzed: rooting and mortality indices, number of leaves and primary shoots, length of the three largest roots per cutting. It was conclude that, the protected environment with plastic cover on sand as substrate must recommended for the rooting of fig estaca, collecting them in the first half of July. The inclination position and cutting depth of the estaca and the substrate coverage with plastic mulching did not influence the results.

A new proposal to guide velocity and inclination in the ramp protocol for the treadmill ergometer

OBJECTIVE: To suggest criteria to guide protocol prescription in ramp treadmill testing, according to sex and age, based on velocity, inclination, and max VO2 reached by the population studied. METHODS: Prospective study describing heart rate (HR), time, velocity, inclination, and VO2 estimated at maximum effort of 1840 individuals from 4 to 79 years old, who performed a treadmill test (TT) according to the ramp protocol. A paired Student t test was used to assess the difference between predicted and reached max VO2, calculated according to the formulas of the "American College of Sports Medicine". RESULTS: Submaximal HR was surpassed in 90.1% of the examinations, with a mean time of 10.0±2.0 minute. Initial and peak inclination velocity of the exercise and max VO2 were inversely proportional to age and were greater in male patients. Predicted Max VO2 was significantly lower than that reached in all patients, except for female children and adolescents (age < 20 years old). CONCLUSION: Use of velocity, inclination, and maximum VO2 actually reached, as a criterion in prescribing the ramp protocol may help in the performance of exercise in treadmill testing. The ramp protocol was well accepted in all age groups and sexes with exercise time within the programmed 8 to 12 minutes.

III - Contribuição para o estudo biológico e ecológico das Podostemaceae do salto do Piracicaba

1 - The Author, in this 3 thd. contribution, concludes the study of the biology and ecology of the species Tristicha trifaria (Willd.) Spreng. and Mourera aspera (Bong.) Tul., both of the Piracicaba Fall. 2 - According to the results of Dr. Peter van Royen (State Herbarium of Leiden, Holland), who made a complete revision of Podostemaceae of the Piracicaba Fall, the species Tristicha hypnoides (St. Hil.) Spreng. var. Hilarii Tul. and Mnioppsis Glazioviana Warm, correspond, respectively, to theTristicha trifaria (Willd.) Spreng. and Mniopsis weddelliana Tul. Apinagia Accorsii Toledo was transferred by Royen to the genus Wettsteiniola. So, its new name is Wettsteiniola accorsii (Toledo) v. Royen. 3 - Propagation by seeds may occur in the following places: a) placenta of partially open fruits; b) external and internal walls of the open capsules; c) pedicels of the fruits; d) remains of rhizomes, branches, etc. e) organic residues accumulated in water holes in the fall; f) clean rocks, in which the little groups of seedlings seems to be a colony of algae. Seeds adhere to the substrata above by means, of a mucilage produced by the transformation of the external integuments in contact with water. 4 - In the growth of the four species below it was found in Piracicaba Fall conspicuous zoning so scattered: a) Wettsteiniola accorsii (Toledo) v. Royen, in rocks situated just within the water fall, where velocity of the current and aeration of the water are very high. b) Tristicha trifaria (Willd.) Spreng. and Mniopsis weddelliana Tul., in rocks at some distance (100 m more or less) upstream until near the bridge across the river. c) Mourera aspera (Bong.) Tul., 300 m upwards the bridge. 5- During 1949, the ecological conditions of the Piracicaba Fall were changed due to the following factors: a) dry season very long, begining from last period of June until 30 november; b) stopping, during four months, of water from the Atibaia river (one of the components of Piracicaba river) near to the city of Americana, in the place where a new station of the Companhia Paulista de Força e Luz was build. In consequence, most of the Podostemaceae died. On the dry rocks there were only fruits and dried plants. 6 - Tristicha trifaria has the same biological and ecological behavior as the Mniopsis weddelliana,. 7 - The vegetative propagation of Tristicha trifaria is made by increasing of its branches, production of stolons with vegetatives buds and regeneration of old parts in especial conditions of water and aeration. 8 - Mourera aspera has the same vegetative propagation as the Wettsteiniola accorsii; it produces stolons (in very little percentage) with vegetative buds, branches of the rhizomes and regeneration of active old parts. 9 - Frequently, there is, on the plants an accumulation of sand, silt, loam, organic substances, and so on. The quantity of material stored depends of the purity of the water, of the morphology of the plants and of the situation on the fall. 10 - In extrem conditions of dry heat, the surviving of the species in its habitat depends exclusively from germination of seeds in the mentioned substrata. Exceptionally, some plants survive in a few water pockets full with the weak remaining current.

Local distribution of blackfly (Diptera, Simuliidae) larvae in two adjacent streams: the role of water current velocity in the diversity of blackfly larvae

This study aimed to evaluate the influence of water velocity speed on the local distribution and taxocenosis structure of blackfly larvae. The larvae were collected from two adjacent streams located in the municipality of Angra dos Reis (RJ): Caputera River and one of its tributaries. Riffle litter patches were sampled randomly using a 30 x 30 cm quadrat. Four blackfly species were found: Simulium incrustatum s. l. Lutz, 1910; Simulium (Inaequalium) sp. ; Simulium pertinax s. l. Kollar, 1832 and Simulium subpallidum s. l. Lutz, 1909. Among these species, Simulium pertinax s. l. was clearly associated with higher water current speeds, while Simulium subpallidum s. l. showed association with lower water velocities, and Simulium (Inaequalium) sp. had a relatively constant distribution along the water current gradient.

Short-term storage in vitro and large-scale propagation of grapevine genotypes

The objective of this work was to evaluate the large-scale propagation of grapevine genotypes after short-term storage in vitro. Microshoots from ten grapevine genotypes were used. The following storage temperatures were evaluated: 10, 20, and 25°C. After short-term storage, the shoots were propagated in up to five successive subcultures, to assess the large-scale propagation of the germplasm maintained under conditions of minimal growth. The propagated shoots were rooted in different concentrations of indolbutiric acid (IBA) and acclimatized in greenhouse. The best temperature for short-term storage in vitro and survival of the genotypes was 20°C. In the propagation phase, the highest number of shoots per explant was found in the subcultures 4 and 5, with averages of 4.9 and 4.8 shoots per explant, respectively. In the rooting phase, the best results for number of roots were obtained using a culture medium supplemented with 0.4 µmol L-1 of IBA, with an average of three roots per shoot. During the acclimation phase, a survival rate higher than 95% was achieved after 30 days in the greenhouse. Grapevine genotypes maintained for six months in vitro, at 20ºC, can be micropropagated in large scale.

THE LYCHEE TREE PROPAGATION BY LAYERING

The aim of the study was to assess the influence of season and different substrates on rooting of air layers of lychee (Litchi chinensisSonn.) for the production of seedlings to ensure the formation of uniform and productive orchards. Air layers were done in plants of the Bengal cultivar using leafy and healthy woody branches, with about 0.010 to 0.015 m in diameter, in which were performed complete girdling with 0.020 m wide at a distance of 0.30 to 0.40 m below the apex. Then the branches were wrapped in moistened substrate. The layering was made at six times of theyear (January, March, May, July, September and November) and two substrates were used (coconut fiber and sphagnum) in a 6 x 2 factorial design in a randomized block with ten replicates. After 90 days, layers were separated from the matrix plant and evaluated for rooting and callus formation, root number, considering only the primary roots, length, area and volume of the roots, beyond the dry weight of roots and calluses. The months of January, March, September and November showed the best results for all analyzed variables related to rooting. With respect to the substrates, the only difference was in January and March to the root number and dry weight of roots, where the sphagnum showed the best results. The month of July was more conducive to the formation of calluses. The period between September and March was more suitable to the propagation of lychee, when there were rooting percentages above 90%, in addition to the formation of large amount of roots.

Propagation through cutting technique of species ocurring in the Lower São Francisco River in Sergipe State with different concentrations of indolbutiric acid

The objective of this work was to evaluate the feasibility of vegetative propagation through cutting technique of seven tree species with strong occurrence in the riparian forest of the Lower São Francisco River in Sergipe State, under different concentrations of indolbutiric acid at 0, 2500, and 5000 mg.L-1, for potentialization of its use in soil bioengineering technique. It was used a complete random block design with three replicates, and a total of twenty-one treatments. The evaluation period was 120 days for each species, and the data collection was made in intervals of fifteen days, in a total of eight evaluations for each species. The evaluated parameters were: Survival Rate, callus formation, and Root Dry matter Weight. Among the studied species, Schinus terebinthifolius Raddi presented the best results related to cutting technique mainly under the indolbutiric acid concentration of 2500 mg.L-1.

Vegetative propagation of bauhinia x blakeana, an ornamental sterile tree

Bauhinia x blakeana (B. purpurea x B. variegata) is a natural hybrid that has been cultivated in gardens, streets and parks. Due to its sterility, it must be vegetatively propagated. The objective of this work was to evaluate the viability of cuttings and grafting on its propagation. Semi-woody cuttings were collected during four seasons and treated with 0; 1,000; 2,000; and 3,000 mg L-1 of IBA. The experimental design was entirely randomized and the treatments were arranged in a 4x4 factorial scheme (four collecting times x four IBA concentrations) and five replications with 10 cuttings each, per collecting time and per IBA concentration. Characteristics of roots and shoots were evaluated after 90 days. The data means were compared by the Tukey test and submitted to the polynomial regression analysis. For the grafting experiment, B. variegata and B. variegata var. candida plants of six and 12 months were used as rootstocks and the splice graft and T-budding methods were tested. The experimental design was entirely randomized and the treatments were arranged in a 2x2x2 factorial scheme (two rootstock species x two grafting methods x two rootstock ages) and four replications with five plants each, per rootstock species, per grafting method and per rootstock age. Characteristics of shoots were evaluated after 90 days and the data means were compared by the Tukey test. B. x blakeana can be propagated by semi-woody cuttings collected in spring, without IBA application, or in summer, with the application of 3,000 mg L-1 of IBA. The tested grafting methods were not effective.

VEGETATIVE RESCUE AND CUTTINGS PROPAGATION OF Araucaria angustifolia (Bertol.) Kuntze

Brazilian pine or araucaria (Araucaria angustifolia) is a coniferous tree with great economic, social and environmental importance in southern Brazil, being exploited for both wood production and for its edible pine nuts. However, no efficient cloning techniques are available and, therefore, the purpose of this study was to evaluate the effectiveness of vegetative rescue methods for cuttings propagation of the species. Shoots/cuttings were generated in two ways: 26 years old trees underwent coppicing and 20 years old trees had the primary branches on the upper third of crown pruned at 2, 20 and 50 cm from the main trunk. Orthotropic shoots were rooted after application of indole-3-butyric acid (IBA) at 0, 2, 4 and 6 g.L-1. Coppicing produced 47 cuttings per plant with 90% orthotropic shoots, while pruning resulted in 182 cuttings per plant with 44% orthotropic shoots. Rooting success indexes were low with no influence of IBA, although they are slightly superior to the ones available in the literature for the species, ranging from 12 to 30% for the coppice shoots and from 0 to 28% for the branches shoots. We conclude that both vegetative rescue techniques are viable and have potentially important applications. Coppicing is recommended for the propagation aiming the production of wood, while shoots derived from the side branches of the crown are more appropriate for seeds orchards formation.

CLONAL PROPAGATION OF NEEM (Azadirachta indica A. Juss.) VIA DIRECT AND INDIRECT IN VITRO REGENERATION

ABSTRACTThe study was conducted with shoot tip explants of neem (Azadirachta indica A. Juss) to identify a viable regenerative process. Shoot tips were obtained from neem embryos cultured alternatingly in DKW medium supplemented with BAP and medium without hormones. Initial shoot development was influenced by cotyledon presence. Basal callus, excised from in vitro stem base, also presented organogenic potential. In some cases, plant lines, obtained from each seed, presented different characteristics. The most common characteristic observed in vitro was callus formation at the stem base. However, the rarest characteristics were stem callus formation and leaf senescence. The regenerated shoot tips were further subculture and rooted on a medium supplemented with IBA so that complete plants could be obtained. The rooted plants were transplanted to a greenhouse and successfully acclimatized. No significant differences in in vivo development were observed between neem plants from callus and from shoot tip propagation.

Thermalhydraulic behavior of electrically heated rod during a critical heat flux transient

In nuclear reactors, the occurrence of critical heat flux leads to fuel rod overheating with clad fusion and radioactive products leakage. To predict the effects of such phenomenon, experiments are performed using electrically heated rods to simulate operational and accidental conditions of nuclear fuel rods. In the present work, it is performed a theoretical analysis of the drying and rewetting front propagation during a critical heat flux experiment, starting with the application of an electrical power step from steady state condition. After the occurrence of critical heat flux, the drying front propagation is predicted. After a few seconds, a power cut is considered and the rewetting front behavior is analytically observed. Studies performed with various values of coolant mass flow rate show that this variable has more influence on the drying front velocity than on the rewetting one.