Comparative evaluation of adverse effects in the use of powder trivalent antivenom and liquid antivenoms in Bothrops snake bites

INTRODUCTION: Snake bite, a problem in public health, generally occurs where there is no electric power. METHODS: A comparative clinical study was conducted with 102 victims of Bothrops snake bite, from the state of Amazonas, Brazil; 58 victims were treated with liofilizated trivalent antivenom serum (SATL) and 44 victims treated with liquid bivalent and monovalent antivenom serum (SAMBL). RESULTS: 17% (10/58) of patients presented adverse effects with the SATL and 25% (11/44) with the SAMBL. CONCLUSIONS: There was no statistic difference in number of adverse effects between the two types of snake bite antivenom.

High prevalence and low E6 genetic variability of human papillomavirus 58 in women with cervical cancer and precursor lesions in Southeast Mexico

Infection with some genotypes of human papillomavirus (HPV) is the most important risk factor associated with cervical cancer (CC). Throughout the world, HPV type 58 prevalence varies from one region to another; it is higher in women from certain countries in Asia and Latin America, such as China and Mexico. Although intratypic variants have been reported on a few occasions, our knowledge about HPV 58 genetic variation remains limited. Therefore, this work aims to (i) determine the prevalence of HPV type 58 amongst Mexican women with invasive CC or precursor lesions and (ii) identify HPV 58 sequence variants. One hundred and forty five colposcopy clinic patients were studied. Genotyping of HPV 16, 18 and 58 was determined by specific nested PCR and HPV 58 variants were detected by direct sequencing. The general prevalence of HPV was 51.7% (75/145). HPV 16 was found in 30.6% (23/75) and HPV 58 in 24% (18/75) of the patients. HPV 18 was not identified in patients with cervical intraepithelial neoplasia (CIN) grade I; it was only found in those with CIN II, with a prevalence of 6.8% (3/44). In patients with CC, the prevalence of HPV 16 and 58 was 78.9%. Regarding HPV 58 variants, 94.4% of the HPV 58 sequences were identical to the prototype strain, whereas one sample showed changes at a single nucleotide. This study demonstrates a high prevalence of HPV 58 and a low genetic variability of E6 sequences amongst Mexican colposcopy patients.

Combination of diatomaceous earth and powder deltamethrin for insect control in stored corn

The use of diatomaceous earth (DE) is a very efficient insect control measure in stored grain IPM due to its low cost, easy application, reduction of active ingredient residues, lower environmental contamination and operator safety. The objective of this research was to evaluate the efficacy of different dosages of DE mixed with powder deltamethrin for controlling Sitophilus zeamais in stored corn. Samples of 100 g of clean and dry corn, in three replicates, were submitted to the following treatments: DE (Keepdry®), at the dosages of 500, 750 and 1000 g/t; powder deltamethrin (K-Obiol®) at 0,5 g a.i. /t and 1,0 g a.i. /t; and combinations of the lowest and highest DE dosages with the two dosages of deltamethrin. Thirty adults of S. zeamais were placed in each vial with the treated grains and kept in environment chambers at 25ºC. Mortality was evaluated from the 1st to the 28th day. In the treatments mixing DE with deltamethrin or deltamethrin alone, the mortalyti was registered since the first day. In the treatments using only DE, the first dead insects were recorded after the 3rd day, especially in the highest dosages. After the 7th day, however, there was no statistical difference among all treatments, except for the lowest dosage of DE which reached a satisfactory control level only by the 14th day. It was concluded that treatments using DE combined with low dosages of powder deltamethrin represent an efficient control measure against S. zeamais in stored corn because insect mortality is faster than in treatments using DE alone and residues of active ingredients are much lower than using the insecticide in high dosages.

Effect of rock powder and vinasse on two types of soils

Can vinasse accelerate the change of minerals in rock dust to obtain fertilizers, using residues from alcohol agro-industries and mining? Answering this question was the main objective of this study. Therefore, an experiment was set up in the laboratory in a completely randomized design using Polyvinyl Chloride (PVC) columns, in which the 0-50 cm layers of a clayey soil (eutroferric Red Oxisol) and sandy soil (Typic Quartzipsamment) were reproduced. We applied three different rates of basalt powder (0.0; 2.0, and 4.0 t ha-1) and one rate of vinasse (200 m³ ha-1) to the soils. The control was made by treatments with water (200 m³ ha-1) with the same rates of rock powder. Samples were first collected on the surface of each column (1, 15, 30, 45, 60, and 90 days after the application of vinasse and rock powder), and, at the end of the experiment, at the various depths and in leached water, to determine pH and the concentration of soluble Ca2+, Mg2+, and K+. There was a significant effect of the solvent and the soil on the surface layer, with higher concentrations found in the treatments with vinasse and in clayey soil, confirming the potential of vinasse to alter minerals in basalt powder. The resulting levels from the beginning to the end of the experiment suggest that sorption phenomena with neoformed mineral phases or organic acids may have occurred. It may be concluded that the use of rock powder and vinasse mixtures is a promising alternative for soil fertilization and recycling of waste from the sugarcane and mining industries.

Oxochloroalkoxide of the Cerium (IV) and Titanium (IV) as oxides precursor

The Cerium (IV) and Titanium (IV) oxides mixture (CeO2-3TiO2) was prepared by thermal treatment of the oxochloroisopropoxide of Cerium (IV) and Titanium (IV). The chemical route utilizing the Cerium (III) chloride alcoholic complex and Titanium (IV) isopropoxide is presented. The compound Ce5Ti15Cl16O30 (iOPr)4(OH-Et)15 was characterized by elemental analysis, FTIR and TG/DTG. The X-ray diffraction patterns of the oxides resulting from the thermal decomposition of the precursor at 1000 °C for 36 h indicated the formation of cubic cerianite (a = 5.417Å) and tetragonal rutile (a = 4.592Å) and (c = 2.962 Å), with apparent crystallite sizes around 38 and 55nm, respectively.

Enantioselective synthesis of aziridines using asymmetric transfer hydrogenation as a precursor for chiral derivatives used as bonding agent for rocket solid propellants

A rapid, expedient and enantioselective method for the synthesis of beta-hydroxy amines and monosubstituted aziridines in up to 99% e.e., via asymmetric transfer hydrogenation of a-amino ketones and cyclisation through treatment with tosyl chloride and base, is described. (1R,2R)-N-(para-toluenesulfonyl)-1,2-ethylenediamine with formic acid has been utilised as a ligand for the Ruthenium (II) catalysed enantioselective transfer hydrogenation of the ketones.The chiral 2-methyl aziridine, which is a potentially more efficient bonding agent for Rocket Solid Propellant has been successfully achieved.

A new experimental procedure to obtain titania powders as anatase phase by a sol-gel process

Titania powders were synthesized by a sol-gel process using titanium tetrabutoxide as precursor. The syntheses were performed in water or in solutions of dimethylformamide (dmf) or dimethylsulfoxide (dmso). It is demonstrated, by X-ray diffraction patterns of the synthesized powders, that the samples obtained in dmf or dmso solutions are crystalline (anatase phase) with some minor amount of brookite phase, whereas the sample synthesized in water is amorphous. The anatase phase can be obtained independently of any previous or further treatment of the synthesized powder, such as hydrothermal or heat treatment, providing a new, simple, quick and inexpensive route to synthesize anatase powders. From the peak broadening of the anatase (101) diffraction, the crystallite sizes were calculated as 6 nm.

Preparación y caracterización de la zeolita MCM-22 y de su precursor laminar

The layered precursor of MCM-22 was prepared with different Si/Al ratios: 15, 25, 50, 100 and ¥. Upon heat treatment these precursors form MCM-22 zeolite. Both layered precursor and MCM-22 zeolite were characterized by several techniques: Chemical Analysis by Atomic Absorption Spectroscopy (AAS), X-Ray Diffraction (XRD), Thermo-gravimetric Analysis (TGA), Pore Analysis by N2 and Ar adsorption, Scanning Electron Microscopy (SEM), Infrared Spectroscopy (IR) and Temperature Programmed Desorption of ammonium (TPD).

Efecto de la naturaleza del precursor sobre las caracteristicas de las nanoparticulas de SnO2 sintetizadas

Tin oxide (SnO2) is widely used in industry as raw material for electronic devices, plating of different types of materials, for dyes and pigments, for electroplating, heterogeneous catalysis, etc. In this work SnO2 was obtained by a controlled precipitation method with special attention to the effects the tin precursor has on the microstructure of the final product. The most appropriate pH for obtaining SnO2 with the rutile structure as the main phase is 6.25 for SnCl2 and 6.40 for SnSO4. After heat treatment at 600 °C, particles of nanometric order (~10 - 30 nm approx) were obtained. The characterization of the solid phase was made by X-ray diffraction (XRD), thermal analysis (DTA/TG), transmission electron microscopy (TEM) and Fourier transformed infrared spectroscopy (FTIR).

Eletrodos positivos tubulares para baterias chumbo ácidas produzidas com material ativo nanométrico

Conventional stationary lead acid batteries positive tubular plates have a specific capacity of about 120 Ah/kg. This value represents an active material utilization coefficient of 50%. The production of these plates includes some initial processes to generate the active PbO2 from a precursor material. In the present work it will be presented a proper and novel methodology to assemble tubular plates directely with nanometric powder of PbO2 particles. The utilization coefficient of these plates was about 80%, and they were able to endure more than 130 severe duty cycles. This high utilization coefficient is a higly desirable feature for electric vehicles batteries.

Sinterabilidade de pós de precursor vitrocerâmico do sistema LZSA tratados por troca iônica

Ion exchange method was employed by means of surface modification of the glass powders of LZSA (Li2O-ZrO2-SiO2-Al2O3) system submitted to a 70wt% NaNO3/30wt% NaSO4 bath salt followed by a heat treatment. Chemical analysis by X-ray fluorescence was used to evaluate the efficiency of ion exchange, while optical dilatometry was employed to evaluate sintering of compacts. Evaluation of the structure of sintered bodies was made by scanning electron microscopy. Substitution of Li+ ions by Na+ ions on the surface of powders during heat treatments of 450 and 600 ºC for 2-10 h promoted an increase in densification of the sintered bodies.

Combined experimental powder X-ray diffraction and DFT data to obtain the lowest energy molecular conformation of friedelin

Friedelin molecular conformers were obtained by Density Functional Theory (DFT) and by ab initio structure determination from powder X-ray diffraction. Their conformers with the five rings in chair-chair-chair-boat-boat, and with all rings in chair, are energy degenerated in gas-phase according to DFT results. The powder diffraction data reveals that rings A, B and C of friedelin are in chair, and rings D and E in boat-boat, conformation. The high correlation values among powder diffraction data, DFT and reported single-crystal data indicate that the use of conventional X-ray diffractometer can be applied in routine laboratory analysis in the absence of a single-crystal diffractometer.

SYNGAS PRODUCTION FROM CO2-REFORMING OF CH4 OVER SOL-GEL SYNTHESIZED Ni-Co/Al2O3-MgO-ZrO2 NANOCATALYST: EFFECT OF ZrO2 PRECURSOR ON CATALYST PROPERTIES AND PERFORMANCE

Ni-Co/Al2O3-MgO-ZrO2 nanocatalyst with utilization of two different zirconia precursors, namely, zirconyl nitrate hydrate (ZNH) and zirconyl nitrate solution (ZNS), was synthesized via the sol-gel method. The physiochemical properties of nanocatalysts were characterized by XRD, FESEM, EDX, BET and FTIR analyses and employed for syngas production from CO2-reforming of CH4. XRD patterns, exhibiting proper crystalline structure and homogeneous dispersion of active phase for the nanocatalyst ZNS precursor employed (NCAMZ-ZNS). FESEM and BET results of NCAMZ-ZNS presented more uniform morphology and smaller particle size and consequently higher surface areas. In addition, average particle size of NCAMZ-ZNS was 15.7 nm, which is close to the critical size for Ni-Co catalysts to avoid carbon formation. Moreover, FESEM analysis indicated both prepared samples were nanoscale. EDX analysis confirmed the existence of various elements used and also supported the statements made in the XRD and FESEM analyses regarding dispersion. Based on the excellent physiochemical properties, NCAMZ-ZNS exhibited the best reactant conversion across all of the evaluated temperatures, e.g. CH4 and CO2 conversions were 97.2 and 99% at 850 ºC, respectively. Furthermore, NCAMZ-ZNS demonstrated a stable yield with H2/CO close to unit value during the 1440 min stability test.

Estudo da decomposição térmica de oxalato de estrôncio dopado com cério(III) como precursor de materiais luminescentes

Este trabalho trata da obtenção de SrC2O4, Ce2(C2O4)3, e SrC2O4 dopado com diferentes porcentagens de Ce3+ como precursores do luminóforo azul Sr2CeO4. Os precursores preparados foram estudados por TG e DTA. Uma mistura contendo SrC2O4 e Ce2(C2O4)3 na relação 4:1 respectivamente e SrC2O4 dopado com diferentes porcentagens de Ce3+, foram tratadas termicamente à 1100ºC, 12 horas. Os produtos foram analisados por XRD e espectroscopia de luminescência e apresentam mistura das fases SrCeO3, Sr2CeO4 e SrCO3. Os produtos contendo a fase Sr2CeO4 apresentam luminescência azul de banda larga, com exceção daquele obtido a partir de SrC2O4 dopado com 50% de Ce3+. Neste caso a fase predominante é SrCeO3. Pela curva DTA observa-se um pico endotérmico em torno de 1000ºC para todas as amostras, com exceção da amostra dopada em 50%, evidenciando a temperatura de formação da fase Sr2CeO4. A fase luminescente Sr2CeO4 é preferencialmente obtida partindo-se de SrC2O4:Ce3+ 25% e de misturas mecânicas na proporção de 4:1 de oxalatos de estrôncio e de oxalato de cério.