Medidas de resistividade elétrica DC em sólidos: como efetuálas corretamente

This paper deals with the most common methods for determining the dc electrical resistivity in solid materials. A brief overview of the fundamental concepts related to the electrical resistivity on materials is introduced. Undoubtedly, the most common and useful procedure to determine the electrical resistivity (rho) is the fourpoint probe method. Some crucial mistakes regarding the experimental procedure and the appropriated correction factors are found in the literature. Thus, the correction factor for the most common sample geometries were gathered and revised in order to provide an easy way to use and apply them.

Construção de uma fonte de corrente e de uma sonda para medida de condutividade pelo método da sonda de quatro pontas

This paper describes the construction of an eletrical current source and of a probe to be used in the measurement of eletrical conductivity through a four-point probe method. These pieces of equipments can be obtained at the low price of US$ 50.00 and are adequate for eletrical conductivity measurements in the semiconductor range, that is from 10-1 to 10-6 S cm-1.

Structural aspects and floristic similarity among tropical dry forest fragments with different management histories in northern Minas Gerais, Brazil

In order to produce useful knowledge to the initiatives of protection and management of forest fragments, more specifically for tropical dry forests which suffer with frequent anthropic activities, and due to the lack of specific studies, this article aimed describe the structure and the floristic similarity among three areas of dry forest with different management histories. The study was developed in Capitão Enéas municipality, Northern Minas Gerais, Brazil, where three fragments were evaluated, being one in regeneration for 30 years, another submitted to occasional fire and the third with selective cut in small scale. The sampling was developed through the point quarter method considering all the alive phanerophyte individuals with circumference at breast height (CBH) > 15 cm. In the three fragments, 512 individuals, distributed in 60 species, 47 genera, and 23 families were sampled. The most representative families were Fabaceae (26), Anacardiaceae (4), Bignoniaceae (3) and Combretaceae (3). However, fourteen families were represented by only one species. Only eight species were common to all fragments - Myracrodruon urundeuva standed out with 26.9% of all sampled individuals - while a great number of species were exclusive of each fragment. The floristic and structural differences between the fragments are possibly related to the history and intensity of management in each area besides the topography variations and the presence or absence of limestone outcrops. These results show the importance of each fragment, indicating that the loss of anyone would cause negative impacts on the regional flora and consequently to the associated biodiversity.

Lognormal abundance distribution of woody species in a cerrado fragment (São Carlos, southeastern Brazil)

The lognormal distribution model is frequently found in communities, especially those which are rich in species and influenced by many environmental factors, as those of the cerrado. We tested the hypothesis that the abundance distribution of woody plant species in a cerrado fragment fits the lognormal model. We placed 20 lines in a cerrado fragment and sampled, with the point-quarter method, 800 individuals with stem perimeter equal or larger than 3 cm. We plotted the abundance-class histogram of the species, verified its normality with the Kolmogorov-Smirnov test, and estimated the expected number of woody species for this community. Of the 63 obtained species, Anadenanthera falcata (with 185 species), Eriotheca gracilipes (43), Stryphnodendron obovatum (37), and Miconia albicans (36) were the most abundant ones. Twelve species were represented by only one individual. We did not reject the null hypotheses that the distribution of woody component species was normal and, thus, their abundances fitted the lognormal model. Therefore, with our work, we can predict that cerrado plant communities fit the lognormal model. If this pattern is maintained in other cerrado communities, there would be implications for the conservation of this vegetation type, because rare species are susceptible of extinction, and implications to their structure, because the dominant species may act as keystone species.

Hypotrophy of conduit artery walls of the offspring of nitric oxide-defective rats

The objective of the present study was to investigate the structure of the arterial walls of the offspring stemming from nitric oxide (NO)-defective hypertensive parents. The parents were treated with N G-nitro-L-arginine methyl ester (40 mg kg-1 day-1) for 5 weeks. Blood pressure was measured noninvasively in six 30-day-old rats and nine age-matched controls. The cardiovascular system was perfused with glutaraldehyde at 120 mmHg. The thoracic aorta and carotid artery were processed for electron microscopy, and geometry was determined by light microscopy. Endothelial cells, smooth muscle cells (SMC) and extracellular matrix (ECM) were determined by the point counting method in electron micrographs of the carotid artery. The blood pressure of experimental offspring was 150.0 ± 2.3 vs 104.6 ± 2.1 mmHg (P < 0.01) for the controls and their heart/body weight ratio of 3.9 ± 0.1 vs 4.4 ± 0.2 (P < 0.05) for the controls indicated cardiac hypotrophy. The wall thickness (tunica intima and media) of the thoracic aorta and carotid artery of experimental offspring was decreased to 78.9% (P < 0.01) and 83.8% (P < 0.01), respectively, compared to controls, as confirmed by a respective cross-sectional area of 85.3% (P < 0.01) and 84.1% (P < 0.01). The wall thickness/inner diameter ratio was reduced to 75% (P < 0.01) in the thoracic artery and to 81.5% (P < 0.01) in the carotid artery. No change in endothelial cell volume density or ECM was observed in the tunica intima of the carotid artery, and SMC volume density was lower in the tunica media (37.6 ± 0.9 vs 44.7 ± 1.1% for controls, P < 0.01), indicating compromised SMC development. Interference with arginine metabolism, a decrease in NO, and other factors are possible mechanisms underlying the structural alterations of the cardiovascular system of offspring from NO-defective hypertensive rats.

A reliable method of quantification of trace copper in beverages with and without alcohol by spectrophotometry after cloud point extraction

A new cloud point extraction (CPE) method was developed for the separation and preconcentration of copper (II) prior to spectrophotometric analysis. For this purpose, 1-(2,4-dimethylphenyl) azonapthalen-2-ol (Sudan II) was used as a chelating agent and the solution pH was adjusted to 10.0 with borate buffer. Polyethylene glycol tert-octylphenyl ether (Triton X-114) was used as an extracting agent in the presence of sodium dodecylsulphate (SDS). After phase separation, based on the cloud point of the mixture, the surfactant-rich phase was diluted with acetone, and the enriched analyte was spectrophotometrically determined at 537 nm. The variables affecting CPE efficiency were optimized. The calibration curve was linear within the range 0.285-20 µg L-1 with a detection limit of 0.085 µg L-1. The method was successfully applied to the quantification of copper in different beverage samples.

PREDICTING THE BOILING POINT OF PCDD/Fs BY THE QSPR METHOD BASED ON THE MOLECULAR DISTANCE-EDGE VECTOR INDEX

The quantitative structure property relationship (QSPR) for the boiling point (Tb) of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) was investigated. The molecular distance-edge vector (MDEV) index was used as the structural descriptor. The quantitative relationship between the MDEV index and Tb was modeled by using multivariate linear regression (MLR) and artificial neural network (ANN), respectively. Leave-one-out cross validation and external validation were carried out to assess the prediction performance of the models developed. For the MLR method, the prediction root mean square relative error (RMSRE) of leave-one-out cross validation and external validation was 1.77 and 1.23, respectively. For the ANN method, the prediction RMSRE of leave-one-out cross validation and external validation was 1.65 and 1.16, respectively. A quantitative relationship between the MDEV index and Tb of PCDD/Fs was demonstrated. Both MLR and ANN are practicable for modeling this relationship. The MLR model and ANN model developed can be used to predict the Tb of PCDD/Fs. Thus, the Tb of each PCDD/F was predicted by the developed models.

Accuracy and efficiency evaluation of point-centered quarter method variations for vegetation sampling in an araucaria forest

In order to verify Point-Centered Quarter Method (PCQM) accuracy and efficiency, using different numbers of individuals by per sampled area, in 28 quarter points in an Araucaria forest, southern Paraná, Brazil. Three variations of the PCQM were used for comparison associated to the number of sampled individual trees: standard PCQM (SD-PCQM), with four sampled individuals by point (one in each quarter), second measured (VAR1-PCQM), with eight sampled individuals by point (two in each quarter), and third measuring (VAR2-PCQM), with 16 sampled individuals by points (four in each quarter). Thirty-one species of trees were recorded by the SD-PCQM method, 48 by VAR1-PCQM and 60 by VAR2-PCQM. The level of exhaustiveness of the vegetation census and diversity index showed an increasing number of individuals considered by quadrant, indicating that VAR2-PCQM was the most accurate and efficient method when compared with VAR1-PCQM and SD-PCQM.

New method for evaluation of cutaneous sensibility in diabetic feet: preliminary report

Diabetic neuropathy is an important complication of the disease, responsible for ulceration and amputation of the foot. Prevention of these problems is difficult mainly because there is no method to correctly access sensibility on the skin of the foot. The introduction of the Pressure-Specified Sensory Device (PSSD TM) in the last decade made possible the measurement of pressure thresholds sensed by the patient, such as touch, both static and in movement, on a continuous scale. This paper is the first in Brazil to report the use of this device to measure cutaneous sensibility in 3 areas of the foot: the hallux pulp, the calcaneus, and the dorsum, which are territories of the tibial and fibular nerves. METHOD: Non-diabetic patients were measured as controls, and 2 groups of diabetic patients - with and without ulcers - were compared. The PSSD TM was used to test the 3 areas described above. The following were evaluated: 1 PS (1-point static), 1 PD (1-point dynamic), 2 PS (2-points static), 2 PD (2-points dynamic). RESULTS: The diabetic group had poorer sensibility compared to controls and diabetics with ulcers had poorer sensibility when compared to diabetics without ulcers. The differences were statistically significant (P <.001). CONCLUSION: Due to the small number of patients compared, the results should be taken as a preliminary report.

Three-dimensional interpolation of soil data: fertility and pedomorphological features in southern Brazil

The graphical representation of spatial soil properties in a digital environment is complex because it requires a conversion of data collected in a discrete form onto a continuous surface. The objective of this study was to apply three-dimension techniques of interpolation and visualization on soil texture and fertility properties and establish relationships with pedogenetic factors and processes in a slope area. The GRASS Geographic Information System was used to generate three-dimensional models and ParaView software to visualize soil volumes. Samples of the A, AB, BA, and B horizons were collected in a regular 122-point grid in an area of 13 ha, in Pinhais, PR, in southern Brazil. Geoprocessing and graphic computing techniques were effective in identifying and delimiting soil volumes of distinct ranges of fertility properties confined within the soil matrix. Both three-dimensional interpolation and the visualization tool facilitated interpretation in a continuous space (volumes) of the cause-effect relationships between soil texture and fertility properties and pedological factors and processes, such as higher clay contents following the drainage lines of the area. The flattest part with more weathered soils (Oxisols) had the highest pH values and lower Al3+ concentrations. These techniques of data interpolation and visualization have great potential for use in diverse areas of soil science, such as identification of soil volumes occurring side-by-side but that exhibit different physical, chemical, and mineralogical conditions for plant root growth, and monitoring of plumes of organic and inorganic pollutants in soils and sediments, among other applications. The methodological details for interpolation and a three-dimensional view of soil data are presented here.

Application of cloud point preconcentration and flame atomic absorption spectrometry for the determination of cadmium and zinc ions in urine, blood serum and water samples

A simple, sensitive and selective cloud point extraction procedure is described for the preconcentration and atomic absorption spectrometric determination of Zn2+ and Cd2+ ions in water and biological samples, after complexation with 3,3',3",3'"-tetraindolyl (terephthaloyl) dimethane (TTDM) in basic medium, using Triton X-114 as nonionic surfactant. Detection limits of 3.0 and 2.0 µg L-1 and quantification limits 10.0 and 7.0 µg L-1were obtained for Zn2+ and Cd2+ ions, respectively. Relative standard deviation was 2.9 and 3.3, and enrichment factors 23.9 and 25.6, for Zn2+ and Cd2+ ions, respectively. The method enabled determination of low levels of Zn2+ and Cd2+ ions in urine, blood serum and water samples.

Determination of triamterene in human plasma and urine after its cloud point extraction

A new analytical approach was developed involving cloud point extraction (CPE) and spectrofluorimetric determination of triamterene (TM) in biological fluids. A urine or plasma sample was prepared and adjusted to pH 7, then TM was quickly extracted using CPE, using 0.05% (w/v) of Triton X-114 as the extractant. The main factors that affected the extraction efficiency (the pH of the sample, the Triton X-114 concentration, the addition of salt, the extraction time and temperature, and the centrifugation time and speed) were studied and optimized. The method gave calibration curves for TM with good linearities and correlation coefficients (r) higher than 0.99. The method showed good precision and accuracy, with intra- and inter-assay precisions of less than 8.50% at all concentrations. Standard addition recovery tests were carried out, and the recoveries ranged from 94.7% to 114%. The limits of detection and quantification were 3.90 and 11.7 µg L-1, respectively, for urine and 5.80 and 18.0 µg L-1, respectively, for plasma. The newly developed, environmentally friendly method was successfully used to extract and determine TM in human urine samples.

Ligandless cloud point extraction of trace amounts of palladium and rhodium in road dust samples using Span 80 prior to their determination by flame atomic absorption spectrometry

In this study, a procedure is developed for cloud point extraction of Pd(II) and Rh(III) ions in aqueous solution using Span 80 (non-ionic surfactant) prior to their determination by flame atomic absorption spectroscopy. This method is based on the extraction of Pd(II) and Rh(III) ions at a pH of 10 using Span 80 with no chelating agent. We investigated the effect of various parameters on the recovery of the analyte ions, including pH, equilibration temperature and time, concentration of Span 80, and ionic strength. Under the best experimental conditions, the limits of detection based on 3Sb for Pd(II) and Rh(III) ions were 1.3 and 1.2 ng mL-1, respectively. Seven replicate determinations of a mixture of 0.5 µg mL-1 palladium and rhodium ions gave a mean absorbance of 0.058 and 0.053 with relative standard deviations of 1.8 and 1.6%, respectively. The developed method was successfully applied to the extraction and determination of the palladium and rhodium ions in road dust and standard samples and satisfactory results were obtained.

Algorithm to determine the intersection curves between bezier surfaces by the solution of multivariable polynomial system and the differential marching method

The determination of the intersection curve between Bézier Surfaces may be seen as the composition of two separated problems: determining initial points and tracing the intersection curve from these points. The Bézier Surface is represented by a parametric function (polynomial with two variables) that maps a point in the tridimensional space from the bidimensional parametric space. In this article, it is proposed an algorithm to determine the initial points of the intersection curve of Bézier Surfaces, based on the solution of polynomial systems with the Projected Polyhedral Method, followed by a method for tracing the intersection curves (Marching Method with differential equations). In order to allow the use of the Projected Polyhedral Method, the equations of the system must be represented in terms of the Bernstein basis, and towards this goal it is proposed a robust and reliable algorithm to exactly transform a multivariable polynomial in terms of power basis to a polynomial written in terms of Bernstein basis .

Substitution-Newton-Raphson method applied to the modeling of a vapour compression refrigeration system using different representations of the thermodynamic properties of R-134a

This paper gives a detailed presentation of the Substitution-Newton-Raphson method, suitable for large sparse non-linear systems. It combines the Successive Substitution method and the Newton-Raphson method in such way as to take the best advantages of both, keeping the convergence features of the Newton-Raphson with the low requirements of memory and time of the Successive Substitution schemes. The large system is solved employing few effective variables, using the greatest possible part of the model equations in substitution fashion to fix the remaining variables, but maintaining the convergence characteristics of the Newton-Raphson. The methodology is exemplified through a simple algebraic system, and applied to a simple thermodynamic, mechanical and heat transfer modeling of a single-stage vapor compression refrigeration system. Three distinct approaches for reproducing the thermodynamic properties of the refrigerant R-134a are compared: the linear interpolation from tabulated data, the use of polynomial fitted curves and the use of functions derived from the Helmholtz free energy.