Onychomycosis by Scytalidium dimidiatum: report of two cases in Santa Catarina, Brazil

Onychomycoses constitute pathologies frequently seen in dermatological practice worldwide. Usually, they are caused by two groups of pathogenic fungi: dermatophytes and yeasts of the Candida genus. However, in a small fraction of the cases, the etiologic agents comprise nondermatophyte molds, belonging to several genera and species. The objective of this study was to present two cases of onychomycosis associated to the mold Scytalidium dimidiatum in patients residing in two cities of Santa Catarina State, Brazil. Aspects of fungal pathogenesis, as well as the epidemiological characteristics and laboratory diagnosis, are discussed.

Amphotericin B associated with triglyceride-rich nanoemulsion: stability studies and in vitro antifungal activity

Amphotericin B (AB) is the standard drug for invasive fungal infection therapy. It has a broad spectrum of activity and it is the best antifungal available against most yeasts and molds. Its therapeutic use, however, is limited by significant side effects, leading to a low therapeutic index when it is used as the traditional formulation (Fungizone®). Due to self-association, AB can form pores in cholesterol-containing membranes. We propose a triglyceride-rich nanoemulsion as a delivery system for AB in low levels of aggregation to reduce the toxicity against host cells.

Influence of duty factor on the die-sinking Electrical Discharge Machining of high-strength aluminum alloy under rough machining

The use of high-strength aluminium alloys as material for injection molding tools to produce small and medium batches of plastic products as well as prototyping molds is becoming of increasing demand by the tooling industry. These alloys are replacing the traditional use of steel in the cases above because they offer many advantages such as very high thermal conductivity associated with good corrosion and wear resistance presenting good machinability in milling and electrical discharge machining operations. Unfortunately there is little technological knowledge on the Electrical Discharge Machining (EDM) of high-strength aluminium alloys, especially about the AMP 8000 alloy. The duty factor, which means the ratio between pulse duration and pulse cycle time exerts an important role on the performance of EDM. This work has carried out an experimental study on the variation of the duty factor in order to analyze its influence on material removal rate and volumetric relative wear under roughing conditions of EDM process. The results showed that high values of duty factor are possible to be applied without bringing instability into the EDM process and with improvement of material removal rate and volumetric relative wear.

Identification of main contamination points by hygiene indicator microorganisms in beef processing plants

The microbiological quality of beef and meat products is strongly influenced by the conditions of hygiene prevailing during their production and handling. Without proper hygienic control, the environment in slaughterhouses and butcher shops can act as an important source of microbiological contamination. To identify the main points of microbiological contamination in the beef processing chain, 443 samples of equipment, installations and products were collected from 11 establishments (1 slaughterhouse and 10 butcher shops) located in the state of Paraná, Brazil. The microbiological quality of all the samples was evaluated using Petri dishes to obtain counts of mesophilic aerobes (AC), total coliforms, Escherichia coli (EC), yeasts and molds (YM). The main contamination points identified in butcher shops, in decreasing order, were stainless steel boxes, beef tenderizers, grinders, knives, mixers, sausage stuffers, plastic boxes, floors and drains. In the slaughterhouse, these points were sausage stuffers, platforms, floors and drains. The most severely contaminated products were fresh sausages and ground beef. This information about the main points of microbiological contamination in the beef processing chain is expected to aid professionals responsible for hygiene in similar establishments to set up proper hygienic procedures to prevent or reduce microbiological contamination of beef and meat products.

Microbiota of sausages obtained by spontaneous fermentation produced in the South of Brazil

The study of the ecology of fermented sausage is fundamental to understand the physical and chemical changes that happen during fermentation and maturation. The aim of the present study was to determine the microbiological characteristics of sausages produced by spontaneous fermentation. Fifty samples of sausages produced in the South of Brazil by different small manufacturers were analyzed for the following microbiota: aerobic mesophilic bacteria; Micrococcaceae; mold and yeast; lactic acid bacteria; total and fecal coliforms; coagulase-positive Staphylococcus, and Salmonella. In most samples (72%), the count of lactic bacteria was higher than 6 log10 cfu.g-1, and the samples with the highest counts were above 8 log10 cfu.g-1. The counts of Micrococcaceae in most samples were between 5 log10 and 7 log10 cfu.g-1. With respect to the presence of molds and yeasts, there was a significant variation among the samples with counts ranging from 2 log10 cfu.g-1 and 6 log10 cfu.g-1. From the data obtained, it was possible to conclude that 24% of the analyzed samples did not comply with the current law in Brazil since the levels of fecal coliforms or coagulase-positive Staphylococcus exceeded the maximum limit allowed.

Stability of porridge pre-mixture made with Brazil nut flour and green banana flour with and without milk powder

The mixture of Brazil nut flour and green banana flour can improve the nutritional value of school meals, allowing for the use of regional ingredients derived from family agriculture. This study aimed to assess the stability of porridge pre-mixtures made with Brazil nut flour and green banana flour during six months of storage. Two types of pre-mixture were evaluated: with and without milk powder. These mixtures were packed in polyethylene/metallized polyester film, vacuum-sealed, and stored at room temperature. The products were evaluated for physicochemical composition, and every 30 days for moisture content, water activity, titratable acidity, pH, peroxide value and acidity of the lipid phase, total and thermotolerant coliforms, yeasts and molds, and sensory acceptance. There was no difference between the mixtures for the parameters evaluated. Moisture content, water activity, acidity of the lipid phase, and the yeast and mold count increased with storage time. The growth of yeasts and molds was more pronounced after 90 days of storage, when water activity reached the limit of 0.60. Although both products had good sensory acceptance throughout the period of study, it is recommended that the shelf life does not exceed 90 days.