Curving simulation and stability of a creep-controlled wheelset for high speed rail-vehicles

Higher travel speeds of rail vehicles will be possible by developing sophisticated top performance bogies having creep-controlled wheelsets. In this case the torque transmission between the right and the left wheel is realized by an actively controlled creep coupling. To investigate hunting stability and curving capability the linear equations of motion are written in state space notation. Simulation results are obtained with realistic system parameters from industry and various controller gains. The advantage of the „creep-controlled wheelset" is discussed by comparison the simulation results with the dynamic behaviour of the special cases „solid-axle wheelset" and „loose wheelset" (independent rotation of the wheels). The stability is also investigated with a root-locus analysis.

Chaos and Unpredictability in the Vibration of an Elasto-Plastic Beam

This contribution discusses the nonlinear dynamics of a pin-ended elasto-plastic beam with both kinematic and isotropic hardening. An iterative numerical procedure based on the operator split technique is developed in order to deal with the nonlinearities in the equations of motion. Free and forced responses for harmonic sinusoidal and square wave excitations are investigated. Numerical simulations present many interesting behaviors such as jump phenomena, sensitivity to initial conditions, chaos and transient chaos. These results indicate that there are practical problems in predicting the response of the beam even when periodic steady state response is expected.

Performance, carcass traits and costs of Suffolk lambs finishing systems with early weaning and controlled suckling

The performance, carcass traits and finishing costs of Suffolk lambs were evaluated in three systems: (1) lambs weaned with 22 kg of body weight (BW) and supplemented with concentrate on pasture until slaughter; (2) lambs weaned with 22 kg BW and fed in feedlot until slaughter; (3) lambs maintained in controlled nursing after 22 kg BW and creep fed in feedlot until slaughter. Average daily gain (ADG) was 224 g/d for lambs weaned and supplemented with concentrate on pasture, 386 g/d for lambs weaned in feedlot and 481 g/d for lambs under controlled nursing. Empty body weight and visceral fat deposition were highest in lambs from feedlot systems. Carcass weights and carcass yields were highest for lambs in controlled nursing. Finishing total costs were highest in controlled nursing and lowest in the system with weaning in feedlot. High concentrate diet associated with controlled nursing in feedlot allowed lambs to reach the growth potential and carcasses with higher weights, higher yields and higher fat content. After weaning, lambs in feedlot fed with high concentrate diet had higher weight gain than lambs supplemented with concentrate on pasture. Carcasses produced under these two systems presented the same characteristics. The system with weaning in feedlot showed the lowest cost per kg carcass.

Alcoolemia em vítimas fatais de acidentes de trânsito no Distrito Federal, Brasil

O objetivo do estudo foi analisar a presença de alcoolemia em vítimas fatais de acidentes de trânsito, no Distrito Federal, em 2005. De 442 óbitos, 163 foram resultantes de atropelamentos, 84 de capotagem e 195 de colisão. A alcoolemia foi dosada em 238 casos (53,7%). A maioria das vítimas era jovem, entre 18 e 35 anos e do sexo masculino. Entre as vítimas de colisão, 44,2% tinham níveis de alcoolemia acima de 0,6 g/l; nas vítimas de capotagens, esse percentual foi de 57,7% e, entre os pedestres, 32,5%. A diferença entre as proporções de vítimas com alcoolemia positiva foi estatisticamente significativa para os que sofreram acidentes de capotagem em relação aos demais.

Análise dinâmico-mecânica: aplicações em filmes comestíveis

Edible films are thin materials based on biopolymers and food additives. The aim of this work is a review on the application of dynamic mechanical analysis in edible film technology. After a brief review of the linear visco-elasticity theory, a description of some practical aspects related to dynamic mechanical analysis, such as sample fixation and sample dehydration during analysis and types and modes of tests are presented. Thus, the use of temperature scanning analysis for glass transition and for plasticizer-biopolymer compatibility studies and frequency scanning tests, less common in edible film technology, are critically reviewed.

Application of the finite element method in cold forging processes

The demand for more efficient manufacturing processes has been increasing in the last few years. The cold forging process is presented as a possible solution, because it allows the production of parts with a good surface finish and with good mechanical properties. Nevertheless, the cold forming sequence design is very empirical and it is based on the designer experience. The computational modeling of each forming process stage by the finite element method can make the sequence design faster and more efficient, decreasing the use of conventional "trial and error" methods. In this study, the application of a commercial general finite element software - ANSYS - has been applied to model a forming operation. Models have been developed to simulate the ring compression test and to simulate a basic forming operation (upsetting) that is applied in most of the cold forging parts sequences. The simulated upsetting operation is one stage of the automotive starter parts manufacturing process. Experiments have been done to obtain the stress-strain material curve, the material flow during the simulated stage, and the required forming force. These experiments provided results used as numerical model input data and as validation of model results. The comparison between experiments and numerical results confirms the developed methodology potential on die filling prediction.

Local Web Buckling in Tapered Composite Beams: A Parametric Study

Composite flooring systems supported by tapered (varying web depth) beams are very attractive from an economic point of view. However, the tapered beam sections are fabricated from plate by welding, and are susceptible to imperfection effects. These may interact with the localised compressive stress field that is generated in the web at a slope change in the lower flange to cause local web buckling. A substantial parametric study using a non-linear elasto-plastic finite element program and covering practical ranges of the important parameters including the area of the tension flange, taper slope and web thickness is reported. Moment-rotation relations, peak moments and failure mechanisms have been predicted. The validity of the work is supported by the good correlation obtained between the results of the parametric study and experimental data.

Modeling of the Fluid-Structure Interaction in Inelastic Piping Systems

In many engineering applications, compliant piping systems conveying liquids are subjected to inelastic deformations due to severe pressure surges such as plastic tubes in modern water supply transmission lines and metallic pipings in nuclear power plants. In these cases the design of such systems may require an adequate modeling of the interactions between the fluid dynamics and the inelastic structural pipe motions. The reliability of the prediction of fluid-pipe behavior depends mainly on the adequacy of the constitutive equations employed in the analysis. In this paper it is proposed a systematic and general approach to consistently incorporate different kinds of inelastic behaviors of the pipe material in a fluid-structure interaction analysis. The main feature of the constitutive equations considered in this work is that a very simple numerical technique can be used for solving the coupled equations describing the dynamics of the fluid and pipe wall. Numerical examples concerning the analysis of polyethylene and stainless steel pipe networks are presented to illustrate the versatility of the proposed approach.

Características físicas de filmes biodegradáveis produzidos a partir de amidos modificados de mandioca

Amidos de mandioca podem ser matérias-primas para a obtenção de filmes biodegradáveis, sendo que para a formação destes é necessária a elaboração de suspensões filmogênicas. Alguns processos de modificação do amido podem torná-lo miscível em água fria, e outros processos de modificação podem alterar as propriedades dos filmes, tornando-os mais fortes e flexíveis. O objetivo deste trabalho foi verificar as características físicas de filmes biodegradáveis elaborados com amidos modificados de mandioca pelo processo de casting (desidratação de uma solução filmogênica sobre placas de Petri). Os amidos modificados utilizados foram: cross linked; carboximetilamido (CMA) de baixa viscosidade e alta viscosidade e esterificado. A viscosidade é fator importante para a elaboração da suspensão filmogênica e foi avaliada utilizando-se o equipamento Rapid Visco Analyser (RVA). Os filmes elaborados foram comparados a um filme de PVC comercial com espessura de 0,0208 a 0,0217 mm. Os amidos foram caracterizados por avaliação da composição físico-química, granulometria, microscopia eletrônica e viscosidade (Rapid Visco Analyser). A análise por microscopia eletrônica dos filmes ressaltou as diferenças entre os diferentes amidos utilizados. O RVA mostrou que, com exceção do cross linked, todos os amidos modificados apresentaram certa solubilidade a frio, o que facilita o preparo das soluções filmogênicas, entretanto, todos os amidos modificados apresentaram redução acentuada da tendência à retrogradação, propriedade geralmente associada à formação de filmes. As espessuras dos filmes de amido variaram de 0,0551 a 0,1279 mm, cujas espessuras mínimas foram a dos filmes de amido cross linked. Os filmes mostraram-se transparentes, manuseáveis e bem homogêneos. Não houve interferência da espessura na permeabilidade ao vapor d'água, e os filmes com 5% de matéria-seca, independente do tipo de amido modificado, foram mais permeáveis que o PVC. Porém, quando se compara o filme biodegradável de amidos modificados com o filme comercial de PVC, ainda há muito que se trabalhar na formulação para melhorar várias propriedades deste tipo de embalagem, que tem amplo uso atualmente.

Caracterização físico-química, reológica, morfológica e térmica dos amidos de milho normal, ceroso e com alto teor de amilose

O objetivo do presente estudo foi avaliar os amidos de milho normal, ceroso e com alto teor de amilose, fabricados pela National Starch, por meio da determinação das suas características físico-químicas, morfológicas, térmicas e reológicas. O amido de milho com alto teor de amilose (AM) apresentou teor de amilose igual a 71%, sendo que os valores obtidos para o amido de milho normal (M) e o amido de milho ceroso (AP) foram de 27,8 e 1,8%, respectivamente. Traços de proteína e lipídios foram encontrados nas amostras. O amido de milho ceroso apresentou maior viscosidade máxima e uma menor tendência à retrogradação, se comparado ao amido de milho normal. O amido AP apresentou menor entalpia de gelatinização, como pode ser observado nas análises de calorimetria exploratória diferencial (DSC), na qual a temperatura de gelatinização foi de 75 °C e o ΔH de 3,34 J.g-1, e também na análise de RVA (Rapid Visco Analyser), em que a temperatura de pasta foi de 71 °C. Apresentando, dessa forma, valores inferiores aos verificados para os outros amidos. O valor do ΔH de retrogradação do amido AP, mostrou-se 25,8% inferior ao ΔH do amido M. O amido AM apresentou o valor de 26,38 J.g-1, demonstrando o maior envolvimento da molécula de amilose no processo de retrogradação. Isso também foi evidenciado pela medida da força dos géis: o gel de AM apresentou força 99,18% superior, retrogradando mais que os outros amidos. As análises de difração de raio X mostraram que os amidos de milho normal e ceroso apresentaram um padrão de difração do tipo A e o amido de milho com alto teor de amilose apresentou padrão do tipo B.

Effect of sugar and water contents on non-expanded cassava flour extrudates

The effects of sucrose and water contents on cassava flour processed by extrusion at varied concentrations of sucrose (0-20% w/w) and water (28-42% w/w) were studied by applying response surface methodology. The extrusion of the mixtures was performed in a twin screw extruder fitted to a torque rheometer. The specific mechanical energy (SME) dissipated inside a conical twin-screw extruder was measured. Water absorption index (WAI), water solubility index (WSI) and paste viscosity readings (cold viscosity (CV), peak viscosity (PV), breakdown (BD) and set back (SB)) during a gelatinization-retrogradation cycle measured in a Rapid Visco Analyzer were determined on non-directly extruded products. The results indicated that SME and WSI decreased as a function of water and sucrose contents. WAI and pasting properties were influenced by water content. A non antiplasticizing effect of the sucrose content was observed on pasting properties, suggesting that sucrose did not reduce the availability of water available for gelatinizing cassava flour during the extrusion process. The nature of the optimum point was characterized as a saddle point for WAI, WSI, PV and BD, whereas SME showed a maximum and CV and SB a minimum. The results indicated to be valuable for the production of non-expanded cassava flour extrudates with desirable functional properties for specific end users.

Efeito da concentração de fibra e parâmetros operacionais de extrusão sobre as propriedades de pasta de misturas de fécula de mandioca e polpa cítrica

Para preencher as várias demandas para funcionalidades em produtos alimentícios, a fécula de mandioca misturada à polpa de laranja desidratada foi extrusada sob diferentes condições (0 a 20% de fibras na mistura); (14,6 a 21,4% de umidade) e (60,8 a 129 ºC) de temperatura de extrusão, objetivando o uso em produtos instantâneos ricos em fibras. A rotação da rosca foi mantida constante em 272 rpm, a abertura da matriz foi 3 mm, a taxa de compressão da rosca foi 3:1 e a taxa de alimentação foi de 150 g/minuto. Os produtos extrusados moídos foram analisados para as propriedades de pasta: viscosidade inicial, pico de viscosidade, quebra de viscosidade, viscosidade final e tendência à retrogradação no Rapid Visco Analyser (RVA), tendo em vista a importância destes parâmetros para este tipo de utilização. Os resultados obtidos mostraram que a porcentagem de fibras foi o parâmetro de maior influência nas propriedades de pasta, e que nas condições de baixo teor de fibras, elevada temperatura e baixa umidade pode ter ocorrido degradação acentuada do amido e solubilização das fibras, levando à redução dos parâmetros de viscosidade.

Desenvolvimento de misturas instantâneas de mandioca e caseína: efeito do teor de proteína e parâmetros de extrusão sobre a viscosidade

O interesse da indústria de alimentos por produtos desenvolvidos a partir de farinhas acrescidas de proteína não se deve somente às suas características nutricionais, senão também às suas propriedades funcionais e reológicas, as quais definem as suas aplicações comerciais. Este trabalho teve por objetivo avaliar o efeito de parâmetros operacionais do processo de extrusão sobre as propriedades de pasta de misturas de farinha de mandioca e caseína. O processo de extrusão seguiu o delineamento 'central composto rotacional' para três fatores: teor de proteína (2,5 a 9,5%), umidade (14,5 a 19,5%) e temperatura de extrusão (65 a 135 ºC). As misturas antes e após a extrusão foram analisadas no Rapid Visco Analyser (RVA) quanto a: viscosidade inicial, pico de viscosidade, quebra de viscosidade, viscosidade final e tendência à retrogradação. Os resultados obtidos nas misturas antes da extrusão mostraram aumento dos valores de viscosidade com o aumento da concentração de proteína até o ponto central (6%) e, nos teores mais elevados de proteína, ocorreu redução destes. Após a extrusão, observou-se que o teor de proteína foi a variável de maior efeito sobre as propriedades de pasta, seguida pela umidade das misturas.

Cooking quality of upland and lowland rice characterized by different methods

Rice cooking quality is usually evaluated by texture and stickiness characteristics using many different methods. Gelatinization temperature, amylose content, viscosity (Brookfield viscometer and Rapid Visco Analyzer), and sensory analysis were performed to characterize culinary quality of rice grains produced under two cropping systems and submitted to different technologies. All samples from the upland cropping system and two from the irrigated cropping system presented intermediate amylose content. Regarding stickiness, BRS Primavera, BRS Sertaneja, and BRS Tropical showed loose cooked grains. Irrigated cultivars presented less viscosity and were softer than upland cultivars. Upland grain samples had similar profile on the viscoamylografic curve, but the highest viscosity peaks were observed for BRS Alvorada, IRGA 417, and SCS BRS Piracema among the irrigated cropping system samples. In general, distinct grain characteristics were observed between upland and irrigated samples by cluster analysis. The majority of the upland cultivars showed soft and loose grains with adequate cooking quality confirmed by sensory tests. Most of the irrigated cultivars, however, presented soft and sticky grains. Different methodologies allowed to improve the construction of the culinary profile of the varieties studied.

Characterization of Brazilian wheat cultivars for specific technological applications

Functional and technological properties of wheat depend on its chemical composition, which together with structural and microscopic characteristics, define flour quality. The aim of the present study was to characterize four Brazilian wheat cultivars (BRS Louro, BRS Timbauva, BRS Guamirim and BRS Pardela) and their respective flours in order to indicate specific technological applications. Kernels were analyzed for test weight, thousand kernel weight, hardness, moisture, and water activity. Flours were analyzed for water activity, color, centesimal composition, total dietary fiber, amylose content and identification of high molecular weight glutenins. The rheological properties of the flours were estimated by farinography, extensography, falling number, rapid visco amylography, and glutomatic and glutork equipment. Baking tests and scanning electron microscopy were also performed. The data were subjected to analysis of variance and principal component analysis. BRS Timbauva and BRS Guamirim presented results that did not allow for specific technological application. On the other hand, BRS Louro presented suitable characteristics for the elaboration of products with low dough strength such as cakes, pies and biscuits, while BRS Pardela seemed suitable for bread and pasta products.