Characterization and use of swine deep bedding ashes in cementitious composites

The deep bedding is a swine alternative production, especially in the finishing phase, whose byproduct can be recycled, reducing the environmental impact. The objectives of this study were to characterize the ash coming from the controlled burning of the swine deep bedding (SDBA) based on rice husk, and to evaluate their performance in composites as a partial substitute for Portland cement (PC). To measure the differences between SDBA and rice husk ash (RHA) as a reference, we have characterized: particle size distribution, real specific density, x-ray diffraction, electrical conductivity, scanning electron microscopy, chemical analysis and loss on ignition. Samples were prepared for two experimental series: control, and another one with the partial replacement of 30% of SDBA in relation to the mass of the Portland cement. According to the results obtained for physical and mechanical characterization, the composites with SDBA can be used as a constructive element in the rural construction.

Formulation and characterization of poloxamer 407®: thermoreversible gel containing polymeric microparticles and hyaluronic acid

The influence of the composition and preparation method on the sol-gel transition temperature (Tsol-gel) and rheological response of poloxamer-based formulations was determined. Manual and more complex mechanical stirring were found to provide similar results. In addition, a linear dependence of Tsol-gel on the poloxamer content was observed in the range of concentrations analyzed, and a Poloxamer 407® concentration of 18% was selected. The addition of hyaluronic acid did not lead to significant changes in the Tsol-gel values. In contrast, the addition of microparticles caused a reduction in Tsol-gel without a significant reduction in gel strength, and pseudoplastic characteristics were observed, indicating that a thermoreversible gel was obtained with a rheology suitable for application in the treatment of burn wounds.

Detection and partial characterization of an isolate of Groundnut ringspot virus in Solanum sessiliflorum

The cubiu (Solanum sessiliflorum) fruit, originating in the Amazon basin, is commonly used in that region for food, medicine, and cosmetics. In an experimental culture of cubiu, in order to evaluate its adaptation to conditions in the Northern region of the state of Rio de Janeiro, it was observed plants with mosaic symptoms. A cubiu plant was collected and analyzed to identify the etiological agent. After mechanical passage through a local lesion host, a host range test was performed. The virus induced chlorotic local lesions in Chenopodium quinoa, necrotic local lesions in Gomphrena globosa, mosaic in S. sessiliflorum, leaf and stem necrosis in tomato (Lycopersicon esculentum) 'Rutgers', mosaic and leaf distortion in Datura stramonium and Physalis floridana, and necrotic local lesions followed by systemic necrosis and plant death in four Nicotiana species. Electron microscopic observations of ultra thin sections from infected cubiu leaves showed the presence of spheroidal, membrane-bound particles typical of tospovirus species. Analysis of the nucleocapsid protein from concentrated virus particles indicated the presence of a 28 kDa protein. RT-PCR was performed after total RNA extraction from infected IPA-6 tomato leaves. A fragment of approximately 0,8 kbp corresponding to the N gene was amplified, cloned and sequenced. The N protein from the cubiu isolate was 95% homologous to the Groundnut ringspot virus (GRSV) protein, and no more than 85% homologous to those from Zucchini lethal chlorosis virus (ZLCV) and Chrysanthemun stem necrosis virus (CSNV), Tomato spotted wilt virus (TSWV), and Tomato chlorotic spot virus (TCSV). This is the first report of the occurrence of GRSV (or any other plant virus) in cubiu.

Detection and partial characterization of a carlavirus causing stem necrosis of soybean in Brazil

Stunting and stem necrosis were noticed in soybeans (Glycine max) grown in 2000/2001 in West Central Brazil the same condition was also observed in the following year in plantations as far as 2,000 km from the initial area. Based on transmission (mechanical, graft, insect vector), purification and serology, electron microscopy and molecular studies the causal agent was determined to be a whitefly-borne carlavirus which is possibly related to Cowpea mild mottle virus (CpMMV).

Characterization and treatment of sisal fiber residues for cement-based composite application

Sisal fiber is an important agricultural product used in the manufacture of ropes, rugs and also as a reinforcement of polymeric or cement-based composites. However, during the fiber production process a large amount of residues is generated which currently have a low potential for commercial use. The aim of this study is to characterize the agricultural residues by the production and improvement of sisal fiber, called field bush and refugo and verify the potentiality of their use in the reinforcement of cement-based composites. The residues were treated with wet-dry cycles and evaluated using tensile testing of fibers, scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. Compatibility with the cement-based matrix was evaluated through the fiber pull-out test and flexural test in composites reinforced with 2 % of sisal residues. The results indicate that the use of treated residue allows the production of composites with good mechanical properties that are superior to the traditional composites reinforced with natural sisal fibers.

Characterization of Lubricating Oil Using Ultrasound

This paper presents an ultrasonic method to measure small concentrations of water in lubricating oil. It uses an ultrasonic measurement cell composed by a piezoceramic emitter (5 and 10 MHz), and a large aperture PVDF receiver that eliminates diffraction effects. The propagation velocity, attenuation coefficient and density of several samples of water-in-oil emulsion were measured. The concentrations of water of the samples were in the range of 0 to 5% in volume, and the results showed that these low concentrations can be discriminated within a resolution of 0.2% in the studied range, using the measurement of the propagation velocity.

Methodology for Photovoltaic Modules Characterization and Shading Effects Analysis

This work describes the methodology, basic procedures and instrumental employed by the Solar Energy Laboratory at Universidade Federal do Rio Grande do Sul for the determination of current-voltage characteristic curves of photovoltaic modules. According to this methodology, I-V characteristic curves were acquired for several modules under diverse conditions. The main electrical parameters were determined and the temperature and irradiance influence on photovoltaic modules performance was quantified. It was observed that most of the tested modules presented output power values considerably lower than those specified by the manufacturers. The described hardware allows the testing of modules with open-circuit voltage up to 50 V and short-circuit current up to 8 A.

Characterization of capacitive sensors for measurements of the moisture in irrigated soils

The irrigation is a technique developed to supply the hydric needs of the plants. The use of the water should be optimized so that the culture just has enough for its growth, avoiding waste. The objective of this work was to characterize the behavior of capacitive sensors of humidity to monitor the moisture in the soils. In first instance, it was appraised sensors with dielectric built of synthetic pomes stone (Rd = 0,4 and Rd = 0,8) and of soil samples (Rd = 0,8 and Rd = 1,0), being the Rd parameter a geometric factor that relates the distance between the capacitor plates with radius of the plates. For the calibration, the sensors were installed in PVC recipient of cylindrical shape, filled with soil. The set (sensor and soil) was humidified by capillary effect and submitted by a natural drying very slowly. The parameter readings were taken daily, which allowed obtain the curves relating the humidity percentage, expressed in terms of dry weight, with the output voltage fort the sensor. The experiments were performed in sand soil and in dark red latossolo. The obtained results allowed to infer that the behavior of the sensor has a specific feature for each type of soil, being, therefore, necessary to develop a own calibration curve for the sensor, when used in soil with specific characteristic.

Development and characterization of edible films based on gluten from semi-hard and soft Brazilian wheat flours (development of films based on gluten from wheat flours)

Edible films based on gluten from four types of Brazilian wheat gluten (2 "semi-hard" and 2 "soft") were prepared and mechanical and barrier properties were compared with those of wheat gluten films with vital gluten. Water vapor, oxygen permeability, tensile strength and percent elongation at break, solubility in water and surface morphology were measured. The films from "semi-hard" wheat flours showed similar water vapor permeability and solubility in water to films from vital gluten and better tensile strength than the films from "soft" and vital gluten. The films from vital gluten had higher elongation at break and oxygen permeability and also lower solubility in water than the films from the Brazilian wheat "soft" flours. In spite of the vital gluten showed greater mechanical resistance, desirable for the bakery products, for the purpose of developing gluten films Brazilian "semi-hard" wheat flours can be used instead of vital gluten, since they showed similar barrier and mechanical properties.

Development and characterization of orally-disintegrating films for propolis delivery

This study aimed at evaluating the effect of different concentrations of hydrolyzed collagen (HC) on the properties of an orally disintegrating film containing propolis ethanol extract (PEE) as an active component. The films were evaluated in terms of total phenols, mechanical properties, solubility, contact angle, disintegration time, and microstructure. The films were prepared by casting with 2 g of protein mass (gelatin and HC), 30 g of sorbitol/100 g of protein mass, and 100 g of PEE/100 g of protein mass. HC was incorporated at concentrations of 0, 10, 20, and 30 g/100 g of protein mass. It was found that increased concentrations of HC reduced tensile strength and increased elongation; however, all films showed plastic behavior. An increase in solubility at 25 ºC, a reduction in the contact angle, and disintegration time were also observed. Thus, higher concentrations of collagen led to more hydrophilic and more soluble polymeric matrices that showed shorter dissolution time, favoring the use of these materials as carriers for active compounds to be delivered in the oral cavity.

Economic viability of the third milking in systems of production using closed-circuit mechanical milking

This study aimed to analyze the economic viability of the third milking in production systems using mechanical milking in a closed circuit, aiming to provide technicians and farmers with information to assist them in decision-making. Specifically, it intended: (a) to estimate the cost of one milking; (b) to estimate the cost of the third milking; (c) to develop a mathematical equation to estimate the minimum amount of milk produced with two milkings, from which it would be economically feasible to do the third milking. Data were collected from three dairy farms, from November 2010 to March 2011, keeping a twice-a-day milking frequency, with three data collections in each farm, totalizing nine collections. Considering the average data, it would be feasible to do the third milking if the average milk yield per day of lactating cows in a twice-a-day milking frequency was greater than or equal to 24.43 kg of milk.

Morphological and phytochemical characterization of Piper hispidinervum DC. and Piper aduncum L. populations in the state of Acre

Because of the increasing demand of the industry for the production of essential oils, studies highlight the genetic variability of Piper hispidinervum and P. aduncum species according to their patterns of spatial distribution, showing the Amazon region as the source of superior genetic material in the production of safrole and dillapiole. Thus, the objective this study was to characterize the morphology and the phytochemistry of Piper hispidinervum and P. aduncum populations in the Active Germplasm Bank of Embrapa Acre to generate subsidies for the genetic improvement of these species. The results showed that the average values for leaf width and length were 141.67 and 48.04 mm, and petioles length and diameter measurements were 2.83 and 1.78 mm for P. hispidinervum and 189.22; 67.74; 6.03 and 2.22 mm for P. aduncum respectively. The average height and canopy volume measurements were 2.39 m and 6.30 m3 and 2.70 m and 7.78 m3 respectively for each species. For P. hispidinervum, the population with higher performance indried yield and content of safrole was population 02, with 3.9%, and the population 04 showed 94.3% safrole content, both with genetic material from the region of Acrelândia and Plácido de Castro. To P. aduncum, the populations with better performance were 207, 208 and 209, forming a homogeneous group with dried yield average of 3.8% and dillapiol content of 84-85%. Such populations are indicated for selection in breeding program of these species due to better performance.

Characterization of heat tolerance in wheat cultivars and effects on production components

Abstract: There is a need for heat tolerant wheat cultivars adapted to the expansion of cultivation areas in warmer regions due to the high demand of this cereal for human consumption. The objective of this study was to evaluate the effect of high temperatures on grain yield and yield components of wheat and characterize heat tolerant wheat genotypes at different development stages. The genotypes were evaluated in the field with and without heat stress. High temperatures reduced the number of spikelets per spike (21%), number of grains per spike (39%), number of grains per spikelet (23%), 1000-grain weight (27%) and grain yield (79%). Cultivars MGS 1 Aliança, Embrapa 42, IAC 24-Tucuruí and IAC 364-Tucuruí III are the most tolerant to heat stress between the stages double ridge and terminal spikelet; MGS 1 Aliança, BRS 264, IAC 24-Tucuruí, IAC 364-Tucuruí III and VI 98053, between meiosis and anthesis; and BRS 254, IAC-24-Tucuruí, IAC-364-Tucuruí III and VI 98053, between anthesis and physiological maturity. High temperatures reduce grain yield and yield components. The number of grains per spike is the most reduced component under heat stress. The genotypes differed in tolerance to heat stress in different developmental stages.

Characterization of verdete rock as a potential source of potassium

Potassium is a nutrient found at low levels in Brazilian soils, requiring large inputs of fertilizers to achieve satisfactory crop yields. Brazil has high external dependence and limited reserves of soluble K mineral, which is traditionally exploited for the production of fertilizers. On the other hand, it is common the occurrence in the country of potassium-rich silicate minerals which are not commercially exploited. This study aimed to characterize mineralogically and chemically samples of verdete rock separated into size fractions and evaluate its potential as potassium fertilizer. The mineral composition of verdete rock is based on glauconite, quartz and feldspar. The total K2O content in verdete rock ranged from 5.18 to 9.0 dag/kg. The K content extracted in water or 2% citric acid was 2.4% below the total of K, indicating low reactivity of verdete rock and limitations for direct use as K source. The processes of physical fractionation and sedimentation in water are inefficient to promote the concentration of K in the different verdete rock fractions. The total K content in some samples are considerable and may enable the use of this rock as raw material for production of more reactive potassium fertilizers.