Análise por difração de raios x de filmes de óxidos cerâmicos compostos por IrO2/TiO2/CeO2

Independent of the sample form (powder or film), XRD analysis of Ir0,3Ti(0,7-x)Ce xO2, (nominal) mixtures, for x=0, shows the formation of a solid solution phase between IrO2 and TiO2, as well as the rutile phases of IrO2 and TiO2. The presence of the anatase phase of TiO2 is also confirmed. The introduction of 30 mol% CeO2 in the mixture reveals the presence of the CeO2 and Ce2O3 phases, besides the already mentioned ones, in the powder. In the film form, however, an amorphous phase is identified. When all of the TiO2 is substituded by CeO2, for both sample forms, the only phases found are IrO2, CeO2 and Ce2O3. This result suggests cerium oxides are not capable of forming solid solutions with either IrO2 or (Ir,Ti)O2 acting solely as a dispersant matrix for these phases. These results are consistent with the much higher electrochemically active surface area when CeO2 is introduced in the binary Ti/Ir0,3Ti0,7O2 mixture. It was possible to establish a relationship between the electrochemical stability of the supported films and their crystalline structure. The unexpected presence of TiO2 and Ti2O3 in the Ti/Ir0,3Ce0,7O2 (film sample) is attributed to oxidation of the Ti support during the calcination step.

Desidrogenação do etilbenzeno sobre compostos de ferro e alumínio

Chromium and potassium-doped iron oxides are widely used as industrial catalysts in the dehydrogenation of ethylbenzene to produce styrene. They have several advantages but deactivate with time, because of the loss of potassium. Also, they are toxic due to chromium compounds. Therefore there is a need for developing alternative non toxic catalysts without potassium. Then, iron and aluminum compounds were prepared by different methods in this work. Different phases were produced depending on the preparation method. Aluminum-doped hematite was more active and selective to styrene than the aluminum ferrite. Aluminum acts both as textural and structural promoter in the catalysts.

Oxochloroalkoxide of the Cerium (IV) and Titanium (IV) as oxides precursor

The Cerium (IV) and Titanium (IV) oxides mixture (CeO2-3TiO2) was prepared by thermal treatment of the oxochloroisopropoxide of Cerium (IV) and Titanium (IV). The chemical route utilizing the Cerium (III) chloride alcoholic complex and Titanium (IV) isopropoxide is presented. The compound Ce5Ti15Cl16O30 (iOPr)4(OH-Et)15 was characterized by elemental analysis, FTIR and TG/DTG. The X-ray diffraction patterns of the oxides resulting from the thermal decomposition of the precursor at 1000 °C for 36 h indicated the formation of cubic cerianite (a = 5.417Å) and tetragonal rutile (a = 4.592Å) and (c = 2.962 Å), with apparent crystallite sizes around 38 and 55nm, respectively.

Immunogold labeling and cerium cytochemistry of the enzyme ecto-5'-nucleotidase in promastigote forms of Leishmania species

We have applied both enzyme cytochemistry and immunological labeling techniques to characterize the enzyme 5'-nucleotidase (5'-Nase), at the ultrastructural level, in promastigote forms of four Leishmania species: Leishmania amazonensis, Leishmania mexicana, Leishmania donovani and Leishmania chagasi. The cerium phosphate staining was localized at the surface of the cell body, the flagellum and the flagellar pocket membranes of all the parasites studied. The immunogold labelling technique confirmed these results. In this report we localized 5'-Nase in L. chagasi and L. amazonensis which have been implicated respectively in visceral and cutaneous forms of leishmaniasis. In addition, we confirmed the localization of this phosphomonoesterase in the other two species studied. The superior quality of the images, obtained with both methodologies, confirms that these parasites possess mechanisms capable of hydrolyzing nucleotide monophosphates, and that the expression of 5'-Nase is associated with the outer surface of the plasma membrane.

Iron oxides in plinthic soils on sedimentary deposits in northeastern Brazil

This study was conducted to examine the distribution and nature of Fe oxides in plinthic soils on the sediments of Barreiras Group (in the state of Piauí) and Itapecuru Formation (in the state of Maranhão) in Northeastern Brazil. Four pedons were selected: a "plinthic, dystrophic, epieutrophic Gray Podzolic with low activity clay" and a "dystrophic Plinthosol with low activity clay" (both Plinthic Kandiustalfs) on the Barreiras sediments, as well as an "eutrophic Plinthosol with low activity clay" and an "allic Plinthosol with low activity clay" (both Plinthustalfs) on the Itapecuru sediments. Soil samples were fractionated into > 2 mm (pisoliths), water-stable aggregates (plinthite) and matrices; the aggregates and matrices were further fractionated into sand, silt and clay sizes. Dithionite extractable iron (Fe d) and aluminum (Al d), as well as oxalate extractable iron (Fe o), were determined for all fractions, and X-ray diffraction analyses were performed on the pisoliths. It was observed that the Plinthustalfs contain more iron oxides, exhibit more extensive plinthite development and have a greater potential for further plinthite development than the Kandiustalfs. The distribution of values for the Fe d indicates that plinthite formation and induration in all soils were accompanied by an enrichment of Fe oxides in all particle size fractions. This Fe segregation was accompanied by aggregation of particles leading to a greater degree of crystallinity, as indicated by analysis of the ratios of Al d:Fe d. Larger ratios of goethite to hematite, and relatively smaller amounts of silicates in the more mature pisoliths were revealed by X-ray diffraction analysis. Ratios of Al d:Fe d were larger in the Kandiustalfs than in the Plinthustalfs, and also larger than expected for Al-substituted Fe oxides. According to ratios of Al d:Fe d, Fe mobilization in all soils has likely occurred under reducing conditions, facilitated by organic matter on the soil surface.

Iron oxides and quality of organic matter in sugarcane harvesting systems

Improvements in working conditions, sustainable production, and competitiveness have led to substantial changes in sugarcane harvesting systems. Such changes have altered a number of soil properties, including iron oxides and organic matter, as well as some chemical properties, such as the maximum P adsorption capacity of the soil. The aim of this study was to characterize the relationship between iron oxides and the quality of organic matter in sugarcane harvesting systems. For that purpose, two 1 ha plots in mechanically and manually harvested fields were used to obtain soil samples from the 0.00-0.25 m soil layer at 126 different points. The mineralogical, chemical, and physical results were subjected to descriptive statistical analyses, such as the mean comparison test, as well as to multivariate statistical and principal component analyses. Multivariate tests allowed soil properties to be classified in two different groups according to the harvesting method: manual harvest with the burning of residual cane, and mechanical harvest without burning. The mechanical harvesting system was found to enhance pedoenvironmental conditions, leading to changes in the crystallinity of iron oxides, an increase in the humification of organic matter, and a relative decrease in phosphorus adsorption in this area compared to the manual harvesting system.

Ação promotora do berílio em catalisadores da síntese do estireno

The catalytic dehydrogenation of ethylbenzene in presence of steam is the main commercial route to produce styrene. The industrial catalysts are potassium- and chromia-doped hematite which show low surface areas leading to bad performance and short life. In order to develop catalysts with high areas, the effect of beryllium on the textural properties and on the catalytic performance of this iron oxide was studied. The influence of the amount of the dopant, the starting material and the calcination temperature were also studied. In sample preparations, iron and beryllium salts (nitrate or sulfate) were hydrolyzed with ammonia and then calcinated. The experiments followed a factorial design with two variables in two levels (Fe/Be= 3 and 7; calcination temperature= 500 and 700ºC). Solids without any dopant were also prepared. Samples were characterized by elemental analysis, infrared spectroscopy, surface area and porosity measurements, X-ray diffraction, DSC and TG. The catalysts were tested in a microreactor at 524ºC and 1 atm, by using a mole ratio of steam/ ethylbenzene=10. The selectivity was measured by monitoring styrene, benzene and toluene formation. It was found that the effect of beryllium on the characteristics of hematite and on its catalytic performance depends on the starting material and on the amount of dopant. Surface areas increased due to the dopant as well as the nature of the precursor; samples produced by beryllium sulfate showed higher areas. Beryllium-doped solids showed a higher catalytic activity when compared to pure hematite, but no significant influence of the anion of starting material was noted. It can be concluded that beryllium acts as both textural and structural promoter. Samples with Fe/Be= 3, heated at 500ºC, lead to the highest conversion and were the most selective. However, catalysts prepared from beryllium sulfate are the most promising to ethylbenzene dehydrogenation due to their high surface area which could lead to a longer life.

Sistema com atmosfera controlada para a caracterização de sensores a gases

This paper describes a sample holder for the electrical measurement of oxides or conducting polymers in the form of pellets or films which are used as gas sensors. The system makes it possible to control the sample temperature, the gas pressure and composition. The temperature in the sample can be changed from 25ºC to 450ºC, and the gas pressure in the chamber is controlled between 5 ¥ 10-4 and 1000 mbar. The performance of the system in resistance measurements of doped tin oxide pellets and polyaniline films deposited on platinum electrodes for methane is analyzed.

Propriedades texturais e catalíticas de óxidos de ferro contendo cromo e cobre

Chromium and copper-doped hematites were prepared with the aim of studying the synergistic effect of these dopants on the textural and on the catalytic properties of the iron oxides towards the high temperature shift reaction. It was found that the most active catalysts were those with the highest amount of copper. They had the Fe(II)/Fe(III) ratio near the stoichiometric value of magnetite, the highest surface areas under the reactional atmosphere and the greatest tendency to produce the active form; they also were poorly crystalline solids. The best performance was shown by the catalyst with Fe/Cu=10, heated at 300ºC. It can thus be concluded that copper acts both as textural and structural promoter in these catalysts.

Effect of adsorbed polyaniline on the thermal stability of iron and arsenic oxides

Iron and arsenic oxide grains are coated with the conducting organic polymer polyaniline. The obtained samples were characterized by infrared spectroscopy, SEM, conducting measurements and thermogravimetry. The thermal stability of both oxides are increased. For As2O3 the sublimation temperature is increased from 165ºC in the pure oxide to 206ºC in the polymer modified sample. The pure Fe3O4 sample exhibits sublimation at 780ºC whereas the polyaniline coated oxide is stable until at least 1000ºC.

Efeito da temperatura no desempenho catalítico de óxidos de ferro contendo cobre e alumínio

Aluminum and copper doped hematite was evaluated in the high temperature shift (HTS) reaction at several temperatures in order to find catalysts that can work in different operational conditions. It was found that the catalysts work in kinetic regime in the range of 300-400 ºC. Both copper and aluminum increases the activity and selectivity. Aluminum acts as textural promoter whereas copper acts as structural one. The most promising catalyst is that with both copper and aluminum which showed higher activity and selectivity than a commercial sample. This catalyst has the advantages of being non toxic and can work at low temperatures.

Redução catalítica seletiva de óxidos de nitrogênio sobre hematita contendo cobre

The activity of copper-doped hematite in the SCR with propane, in the presence of oxygen, was evaluated in this work. It was found that copper sulfate led to the production of solids with different specific surface areas depending on the amount of copper. The sulfur and copper species were mainly located on the surface. The copper-containing catalysts were more active in the reduction of nitrogen oxides and less active in the propane oxidation as compared to pure hematite. This behavior was assigned to an association of both sulfur and copper species to produce new sites active for NO reduction.

Elimination of dyes from aqueous solutions using iron oxides and chitosan as adsorbents: a comparative study

This work investigates the adsorption of Alizarin, Eriochrome Blue Black R and Fluorescein using chitosan, goethite and magnetite as adsorbents. For Alizarin, the best adsorbent is chitosan with a Langmuir parameter of 15.8 mmol dye/g adsorbent. For Eriochrome Blue Black R only 1.94 mmol dye/g chitosan is adsorbed. Langmuir parameters for the Alizarin adsorption on both iron oxides display one or two orders of magnitude lower than for chitosan and two orders of magnitude lower in the case of Eriochrome Blue Black R. Fluorescein does not adsorb in appreciable amounts on chitosan and it presents the lower affinity on the iron oxides.

Influence of basic properties of Mg,Al-mixed oxides on their catalytic activity in knoevenagel condensation between benzaldehyde and phenylsulfonylacetonitrile

The catalytic performance of Mg,Al-mixed oxides (MO20, MO25 and MO33) derived from hydrotalcites was evaluated in the Knoevenagel reaction between benzaldehyde and phenylsulfonylacetonitrile at 373 and 383 K. The best results were obtained for the sample MO20 that presented the highest basic sites density and external area and the smallest crystallite sizes. The relative amount of basic sites with weak to intermediate strength also played an important role on catalytic performance. By increasing the catalyst content from 1 to 5 wt.% at 383 K, a complete conversion of the reactants is attained, producing α-phenylsulfonylcinnamonitrile with a selectivity of 100%.

O efeito da desativação térmica nas propriedades oxirredutoras e na atividade catalítica de catalisadores CZ e Pd-CZ

Automotive catalyst, using in Brazil since 1992, is a essential technology for vehicular emissions control. Noble metals are the active phase of these catalysts, and cerium zirconium mixed oxides (CZ), responsibles for the oxygen storage capacity (OSC), one of the most important aspect for the operational performance of the catalyst. In this context, the oxireduction properties analysis of CZ and Pd/CZ (palladium supported in CZ) system are the objective of this study, as well as, the impact of the thermal aging in the OSC. Aging consisted of treatments at 900 or 1200 °C, for 12 or 36 h, in oxidizing condition.