Liver function evaluation in leptospirosis with colloidal gold 1 9 8 Au

Eight patients with leptospirosis were studied with colloidal gold 1 9 8 Au. The radiocolloidal hepatic distribution was altered, presenting a non-homogeneous tiver concentration in seven cases, and a minute to moderate splenic visualization in five. Two patients presented doubtful splenic image, and one seemed to be normal. Liver scanning with colloidal gold 1 9 8 Au is demonstra ted to be a good liver function test.

Detailed crystallization study of co-precipitated Y1.47Gd1.53Fe5O12 and relevant magnetic properties

The crystallization process of co-precipitated Y1.5Gd1.5Fe5O12 powder heated up to 1000 ºC at rate of 5 °C min-1 was investigated. Above 810 ºC crystalline Y1.47Gd1.53Fe5O12 was obtained with a lattice parameter of 12.41 Å and a theoretical density of 5.84 g cm-3. Dry pressed rings were sintered at 1270 and 1320 ºC, increasing the grain-size from 3.1 to 6.5 µm, the theoretical density by 87.6 to 95.3% and decreasing Hc from 2.9725 to 1.4005 Oe. Additionally, Hc increased when the frequency of the hysteresis graph varied from 60 Hz to 10 kHz, the curie temperature was 282.4 ºC and Ms equalled 9.25 emu g-1 (0.17 kG) agreeing well with the Bs-value of the hysteresis graph and literature values.

Lipid peroxidation, antioxidant enzymes and glutathione levels in human erythrocytes exposed to colloidal iron hydroxide in vitro

The free form of the iron ion is one of the strongest oxidizing agents in the cellular environment. The effect of iron at different concentrations (0, 1, 5, 10, 50, and 100 µM Fe3+) on the normal human red blood cell (RBC) antioxidant system was evaluated in vitro by measuring total (GSH) and oxidized (GSSG) glutathione levels, and superoxide dismutase (SOD), catalase, glutathione peroxidase (GSH-Px) and reductase (GSH-Rd) activities. Membrane lipid peroxidation was assessed by measuring thiobarbituric acid reactive substance (TBARS). The RBC were incubated with colloidal iron hydroxide and phosphate-buffered saline, pH 7.45, at 37oC, for 60 min. For each assay, the results for the control group were: a) GSH = 3.52 ± 0.27 µM/g Hb; b) GSSG = 0.17 ± 0.03 µM/g Hb; c) GSH-Px = 19.60 ± 1.96 IU/g Hb; d) GSH-Rd = 3.13 ± 0.17 IU/g Hb; e) catalase = 394.9 ± 22.8 IU/g Hb; f) SOD = 5981 ± 375 IU/g Hb. The addition of 1 to 100 µM Fe3+ had no effect on the parameters analyzed. No change in TBARS levels was detected at any of the iron concentrations studied. Oxidative stress, measured by GSH kinetics over time, occurs when the RBC are incubated with colloidal iron hydroxide at concentrations higher than 10 µM of Fe3+. Overall, these results show that the intact human RBC is prone to oxidative stress when exposed to Fe3+ and that the RBC has a potent antioxidant system that can minimize the potential damage caused by acute exposure to a colloidal iron hydroxide in vitro.

Role of Tamm-Horsfall protein and uromodulin in calcium oxalate crystallization

One of the defenses against nephrolithiasis is provided by macromolecules that modulate the nucleation, growth, aggregation and retention of crystals in the kidneys. The aim of the present study was to determine the behavior of two of these proteins, Tamm-Horsfall and uromodulin, in calcium oxalate crystallization in vitro. We studied a group of 10 male stone formers who had formed at least one kidney stone composed of calcium oxalate. They were classified as having idiopathic nephrolithiasis and had no well-known metabolic risk factors involved in kidney stone pathogenesis. Ten normal men were used as controls, as was a group consisting of five normal women and another consisting of five pregnant women. Crystallization was induced by a fixed supersaturation of calcium oxalate and measured with a Coulter Counter. All findings were confirmed by light and scanning electron microscopy. The number of particulate material deposited from patients with Tamm-Horsfall protein was higher than that of the controls (P<0.001). However, Tamm-Horsfall protein decreased the particle diameter of the stone formers when analyzed by the mode of the volume distribution curve (P<0.002) (5.64 ± 0.55 µm compared to 11.41 ± 0.48 µm of uromodulin; 15.94 ± 3.93 µm and 12.45 ± 0.97 µm of normal men Tamm-Horsfall protein and uromodulin, respectively; 8.17 ± 1.57 µm and 9.82 ± 0.95 µm of normal women Tamm-Horsfall protein and uromodulin, respectively; 12.17 ± 1.41 µm and 12.99 ± 0.51 µm of pregnant Tamm-Horsfall protein and uromodulin, respectively). Uromodulin produced fewer particles than Tamm-Horsfall protein in all groups. Nonetheless, the total volume of the crystals produced by uromodulin was higher than that produced by Tamm-Horsfall protein. Our results indicate a different effect of Tamm-Horsfall protein and uromodulin. This dual behavior suggests different functions. Tamm-Horsfall protein may act on nucleation and inhibit crystal aggregation, while uromodulin may promote aggregation of calcium oxalate crystals.

Production and characterization of monoclonal antibodies to the edta extract of Leptospira interrogans, serovar icterohaemorrhagiae

Monoclonal antibodies (MABs) ivere produced against an etbylenediaminetetraacetate (EDTA) extract of Leptospira interrogans serovar icterohaemorrhagiae being characterized by gel precipitation as IgM and IgG (IgGl and IgG2b). The EDTA extract was detected as several bands by silver staining in SDS-PAGE. In the Western blot the bands around 20 KDa reacted with a monoclonal antibody, 47B4D6, and was oxidized by periodate and was not digested by pronase, suggesting that the determinant is of carbohydrate nature, lmmunocytochemistry, using colloidal gold labeling, showed that an EDTA extract determinant recognized by monoclonal antibody 47B4D6, is localized under the outer envelope of serovar icterohaemorrhagiae. Hoe AIAB raised against the EDTA extract was not able to protect hamsters from lethal challenge with virulent homologous leptospires.

The ceramic artifacts in archaeological black earth (terra preta) from lower Amazon region, Brazil: mineralogy

Several archaeological black earth (ABE) sites occur in the Amazon region. They contain fragments of ceramic artifacts, which are very important for the archaeological purpose. In order to improve the archaeological study in the region we carried out a detailed mineralogical and chemical study of the fragments of ceramic artifacts found in the two ABE sites of Cachoeira-Porteira, in the Lower Amazon Region. Their ceramics comprise the following tempers: cauixi, cariapé, sand, sand +feldspars, crushed ceramic and so on and are composed of quartz, clay equivalent material (mainly burned kaolinite), feldspars, hematite, goethite, maghemite, phosphates, anatase, and minerals of Mn and Ba. Cauixi and cariapé, siliceous organic compounds, were found too. The mineralogical composition and the morphology of their grains indicate a saprolite (clayey material rich on quartz) derived from fine-grained felsic igneous rocks or sedimentary rocks as source material for ceramic artifacts, where silica-rich components such cauixi, cariapé and/or sand (feldspar and rock fragments) were intentionally added to them. The high content of (Al,Fe)-phosphates, amorphous to low crystalline, must be product of the contact between the clayey matrix of pottery wall and the hot aqueous solution formed during the daily cooking of animal foods (main source of phosphor). The phosphate crystallization took place during the discharge of the potteries put together with waste of organic material from animal and vegetal origin, and leaving to the formation of the ABE-soil profile.

Arsenicais e inseticidas orgânicos sôbre o algodoeiro em terras roxa e arenosa

The authors carried out a series of pots and plots experiments applying arsenical and organic insecticides to cotton plants cultivated in "terra roxa" and in a sandy soil. The first results were presented in 1947, to the la. Reunião Brasileira de Ciência do Solo (First Brazilian Congress of Soil Science); they pointed out the danger resulting from the accumulation of arsenic in soils due to the constant applications of arsenicais to control cotton pests; in the course of the time, the amount of residual arsenic in the soil would determine a decrease in cotton yield caused by its toxic effect on the crop. The following conclusions were drawn from the last three experiments: 1) the field experiment conducted in a sandy soil to which lead arseniate was applied in increasing rates produced a reduction of 50 per cent in the yield (the three highest doses were responsible for this result); by this way, the pot experiment published in 1947 was confirmed); 2) in the pot experiment with "terra roxa" toxic effects appeared only in the plants receiving the last dosis of lead arsenate; this result is explained quite naturally by a considerable absorption of the AsO4 --- ion by "terra roxa" colloidal material; furthermore the CaO, P2O5 and Fe2O3 content and the pH value (higher) would decrease the arsenate solubilization in the soil considered; 3) the pot experiment with organic insecticides applied in the rates usually employed in the control of cotton pests, showed that 10% D.D.TD. and 2.5% Rotenone did not affect cotton plants cultivated in a sandy soil; however we agree with FOSTER (1951), in the point that both mineral and organic insecticides must be applied in the minimum amount as possible; we also think that experiments like those should be carried out with the known insecticides, in several soil conditions and with many crops in order to determine the maximum limits of tolerancy.

Avaliação da capacidade de fixação de fósforo pelo solo

Phosphate "fixation" is the convertion of soluble into insoluble phosphate in the soil. There are many factors conditioning phosphate fixation by soil such as reactions originating less soluble compounds (phosphates of iron, aluminum, calcium, magnesium, etc.), PO4-3 adsorption by the colloidal fraction of soils, PO4-3 absorption by the soil microflora, etc. Certain soils of the state of São Paulo (Brazil) are relatively rich in both iron and aluminum oxides. PO4-3 fixation, using P31 and P32 has been verified by researchers, specially with "Terra Roxa". The known methods for fixation evaluation are conventional as this depends on phosphate solution concentration, pH, time of contact between soil and solution, relation of sample weight to solution volume, shaking time, etc. In this experiment, the following conventional method was used: 4 g of soil were shaken for 15 minutes at 30-40 rpm, in 300 ml Erlenmeyer flask in a Wagner shaking machine, together with 100 ml of 0,03 normal phosphate solution (being 0,01 normal as PO4-3 contributed by H8PO4 and 0,02 normal as PO4-3 from KH2PO4). After shaking it was set aside for 24 hours and then filtered. Phosphate was determined in a suitable aliquot of both the original solution (blank) and the soil extract, by the vanadomolibidic-phosphoric acid method. From phosphate concentration in the blank minus phosphate concentration in the soil stract the rate of fixation by 100 g of soil was calculated. The data obtained show that "Terra Roxa" and "Terra Roxa Misturada" have a fairly high PO4-3 fixation capacity, varying from 10 to 24 milliequivalents of PO4-3 per 100 g of soil.

Litosol: suas características e provável gênese

Some of the characteristics peculiar to Litosois are discussed based on data published on Litosois occurring in the States of São Paulo and Paraná. Litosois are the first stages of development of a soil. Litosois probably originate through the exposure of the rockbed caused by an excessive relief. Rock weathering processes are intensive, prevailing those of chemical nature rather than those processes in which physical phenomena dominate. The A horizon has a high organic matter content (2% to 10%). Silt and clay amount to approximately 50% of the fine earth in the A horizon, with the exception of Litosois originated from sandstone and granite. The SiO2/Al2O3 relationship of the soil's colloidal complex and the clay's cation exchange capacity indicate that it is quite probable the presence of 2:1 type clay in Litosois derived from basic rocks.

Basic Surface Properties of Mononuclear Cells from Didelphis marsupialis

The electrostatic surface charge and surface tension of mononuclear cells/monocytes obtained from young and adult marsupials (Didelphis marsupialis) were investigated by using cationized ferritin and colloidal iron hydroxyde, whole cell electrophoresis, and measurements of contact angles. Anionic sites were found distributed throughout the entire investigated cell surfaces. The results revealed that the anionic character of the cells is given by electrostatic charges corresponding to -18.8 mV (cells from young animals) and -29.3 mV (cells from adult animals). The surface electrostatic charge decreased from 10 to 65.2% after treatment of the cells with each one of trypsin, neuraminidase and phospholipase C. The hydrophobic nature of the mononuclear cell surfaces studied by using the contact angle method revealed that both young and adult cells possess cell surfaces of high hidrofilicity since the angles formed with drops of saline water were 42.5°and 40.8°, respectively. Treatment of the cells with trypsin or neuraminidase rendered their surfaces more hydrophobic, suggesting that sialic acid-containing glycoproteins are responsible for most of the hydrophilicity observed in the mononuclear cell surfaces from D. marsupialis.

Vidros recobertos com camadas delgadas transparentes de SnO2

SnO2 thin layers, prepared from aqueous colloidal suspensions by the sol-gel process, have been dip-coated on commercial borosilicate glasses. The effect of the conditions of deposition on the optical and structural characteristics of the thin layers was analysed by UV-Vis spectroscopy, x-ray reflectometry and electron scanning microscopy. Layers prepared with withdrawal speed in between 0.1 and 10cm/min show thickness smaller than 90nm, roughness of the order of 2nm and transmittance higher than 80%, resulting in good optical quality samples. The roughness increases from 2 to 11nm as the withdrawal speed increases from 10 to 80cm/min, what seems to be associated to the enlargement of the layers thickness (> 90nm). The measurements of mass loss, done after etching with fluoridric acid show that the coated samples are more corrosion resistant than the uncoated borosilicate glass.

Rotas de síntese e a homogeneidade dos precursores de mulita e cordierita

Multicomponent ceramics are mainly synthesized by conventional solid-state reaction route and sol-gel routes. In the sol-gel route, colloidal or polymeric gel are envolved. In this work, some principles of the chemistry of theses routes are discused and it is ilustrated a variety of strategies for obtaining a homogeneous multicomponent precursors.

Utilização de eletrodos potenciométricos de amálgama em estudos de complexação de substâncias húmicas

Potentiometric amalgam electrodes of lead, cadmium, and zinc are proposed to study the complexation properties of commercial and river sediment humic acids. The copper complexation properties of both humic acids were studied in parallel using the solid membrane copper ion-selective electrode (Cu-ISE). The complexing capacity and the averaged conditional stability constants were determined at pH 6.00 ± 0.05 in medium of 2x10-2 mol L-1 sodium nitrate, using the Scatchard method. The lead and cadmium amalgam electrodes presented a Nernstian behavior from 1x10-5 to 1x10-3 moles L-1 of total metal concentration, permitting to perform the complexation studies using humic acid concentrations around of 20 to 30 mg L-1, that avoids colloidal aggregation. The zinc amalgam electrode showed a subnernstian linear response in the same range of metal concentrations. The Scatchard graphs for both humic acids suggested two classes of binding sites for lead and copper and one class of binding site for zinc and cadmium.

Metodologia para o crescimento de esferas monocristalinas de metais nobres

This paper describes in detail a technique employed to grow quasi-spherical single crystals of noble metals for electrochemical applications, using platinum as an example. The metal beads were formed by melting the extremity of a wire in an oxygen / butane flame. X-ray techniques were used to check the crystallization and to determine the orientation of the crystals. Treatment with a pure hydrogen flame followed by a cooling procedure in a hydrogen / argon atmosphere were used for conditioning the well-defined platinum single crystal surfaces. Finally, electrochemical characterization of the Pt(111), Pt(110) and Pt(100) surfaces was done in diluted sulfuric acid solution in the hydrogen adsorption / desorption potential region.

Nano vitrocerâmica de escória de aciaria

The manufacture of glass-ceramics is an alternative route for the commercial use of metallurgical slags. Such types of glass-ceramics may find commercial applications owing to their low cost, good mechanical properties and superior visual aspect. Besides, due to the elimination of that industrial residue from the environment and also due to the possibility of replacement of natural stones such as marbles and granites, the use of slags is an activity with strong ecological appeal. While the use of blast-furnace slags for the production of glass-ceramics is well known, the utilization of steel making slags constitutes a challenge, because these materials possess low concentration of SiO2. In this work a novel composition for producing glasses and glass-ceramics from a steelmaking slag is presented. The crystal nucleation kinetics, the characterization of the resulting microstructures for two different thermal treatments and mechanical properties of the glass-ceramics are discussed. A glass-ceramic having a marble aspect, fine volumetric crystallization, high degree of crystallization and improved mechanical strength was obtained.