Citric acid as multifunctional agent in blowing films of starch/PBAT

Citric acid was used as a compatibilizer in the production of starch and PBAT films plasticized with glycerol and processed by blow extrusion. Films produced were characterized by WVP, mechanical properties, FT-IR-ATR and SEM. WPV ranged from 3.71 to 12.73×10-11 g m-1 s-1 Pa-1, while tensile strength and elongation at break ranged from 1.81 to 7.15 MPa and from 8.61 to 23.63%, respectively. Increasing the citric acid concentration improved WVP and slightly decreased film resistance and elongation. The films micrographs revealed a more homogeneous material with the addition of citric acid. However, the infrared spectra revealed little about cross-linking esterification reaction

Gray mold severity and vase life of rose buds after pulsing with citric acid, salicylic acid, calcium sulfate, sucrose and silver thiosulfate

Gray mold of roses (Rosa hibrida) caused by Botrytis cinerea requires many management strategies for its control. The effect of pulsing rose cv. Kiss with solutions of citric acid, salicylic acid, sucrose, calcium sulfate, and silver thiosulfate (STS) on disease severity and vase life of the flowers was evaluated. The solutions were applied to cut stems at different stages of harvest, the variation in the opening stage of harvest did not affect the results. Pulsing with STS reduced the values of area under the disease progress curve (AUDPC) and of severity of disease by 15% and 55%, respectively, and increased the vase life of the flowers by 20%. Calcium sulfate consistently reduced AUDPC by 66% and maximum severity by 88%, and increased vase life of the flowers by 37%. Therefore, pulsing rose buds with solutions of STS and calcium sulfate is potentially useful in reducing losses due to gray mold after harvest and in extending the vase life.

Influence of passion fruit albedo, citric acid, and the pulp/sugar ratio on the quality of banana preserves

The objective of this research was to evaluate the effect of the citric acid concentration, pulp/sugar ratio, and albedo concentration of the passion fruit peel on physical, physiochemical, and sensorial characteristics of the 'Silver' banana preserves. A 2³ factorial design and 3 repetitions in the central point were used. The albedo concentration between 0 and 3% had significant influence on the reduction of the reducing sugars and on the decrease in titratable acidity. The increase in the pulp/sugar ratio exerted a negative effect on the pH and positive on the titratable acidity; the acid addition reduced the non-reducing sugar level. The sensorial evaluation and purchase intention indicated that the incorporation of a maximum of 1.5% albedo in formulations containing 50% pulp and 0.5% citric acid resulted in products with good acceptability in comparison with the formulation in which 60% pulp and an absence of acid or albedo is utilized.

Organic acid adsorption and mineralization in oxisols with different textures

Organic acids play an important role in the nutritional conditions of plants. Their relevance is related to their formation dynamics, mineralization rate and adsorption by soil colloids. This study was carried out to evaluate the dynamics of mineralization and adsorption of organic acid (acetic acid - AA, citric acid - CA and humic acid - HA) applied to the soil. Samples of two Oxisols were used: Rhodic Haplustox (LV) and Typic Haplustox (LVA). The mineralization experiment was arranged in a 2 x 3 x 5 factorial design, based on the factors: two soils (LV and LVA) x three organic acid (OA) types (AA, CA and HA) x five OA rates (0, 1, 2, 4, and 8 mmol dm-3). Organic carbon mineralization in samples was measured by the C-CO2 efflux, produced by the microbial activity, in a 30-day (measurements after 4, 8, 12, 21, and 30 days) and in a 4-day experiment (measured after 24, 48, 72 and 96 h). Organic acid adsorption was tested in a 2 x 2 x 5 x 4 factorial design, with the factors and levels: two Oxisols; two organic acids (AA and CA); five OA rates (0, 1, 2, 4, and 8 mmol dm-3) and four adsorption periods (6, 24, 48, and 72 h). The C-CO2 production of soil treated with CA was highest. In the adsorption experiment, the affinity of CA to soil adsorption sites was greatest. The adsorption of organic acids to soils may be an important mechanism by which bioavailability and thus mineralization capacity by microbial activity are reduced.

Characterization of Ornamental Rock Residue and Potassium Liberation Via Organic Acid Application

ABSTRACT Organic acids present in organic matter and, or, exudates by microorganisms and plants can increase the liberation of potassium present in minerals. The objective of this study was to characterize the residue from ornamental rocks and evaluate the release of K from these residues after the application of organic acids. The experiment was conducted under laboratory conditions and followed a 2 × 3 × 5 factorial design with three replicates. The studied factors were: two organic acids (citric acid and malic acid), three ornamental rock residues (R1, R2 and R3) and five organic acid rates (0, 5, 10, 20 and 40 mmol L-1). After agitation, K concentrations were determined in the equilibrium solution. Successive extractions were performed (1, 5, 10, 15, 30 and 60 days after the start of the experiment). The organic acids used (citric and malic) promoted the release of up to 4.86 and 4.34 % of the total K contained in the residue, respectively, reinforcing the role of organic acids in the weathering of minerals and in providing K to the soil. The K quantities were, on average, 6.1 % higher when extracted with citric acid compared to malic acid.

Initial performance of pineapple and utilization of rock phosphate applied in combination with organic compounds to leaf axils

Rock phosphates have low solubility in water, but good solubility in acid. The use of organic compounds together with these phosphorus sources applied to the basal leaf axils of pineapple can increase the solubility of this phosfate source and increase the P availability to the crop. A greenhouse experiment was conducted using Araxá rock phosphate (10 g) in combination or not with solutions containing increasing concentrations of humic acids (0 to 40 mmol L-1 of carbon), with or without citric acid (0.005 mmol L-1), applied to basal leaf axils of pineapple cv. Pérola. Growth and nutritional characteristics of aerial plant parts were assessed. Growth rates of aerial parts and N, P, K, Ca and Mg contents increased curvilinearly with increasing concentration of carbon in the form of humic acids. Maximum values were found for the concentration of 9.3 mmol L-1 of carbon combined with 0.005 mmol L-1 of citric acid and natural phosphate.

Postharvest quality of cocona (Solanum sessiliflorum Dunal) stored under ambient condition

Cocona (Solanum sessiliflorum Dunal) is an important genetic resource that has been traditionally used for a variety of purposes, including food, medical and cosmetics applications. The objective of this study was evaluated the quality and the period of postharvest shelf life of cocona 'Mosquet", through the physical, chemical and physiological characterization of fruits stored under the ambient conditions. Physiologically mature fruits were harvested from an orchard, washed with tap water and soaked in a solution of the fungicide Prochloraz (49.5 g/100 L of water) for 5 minutes. After air drying, the fruits were packed in plastic containers and stored at 24 ± 2 ºC and relative humidity 60 ± 5% for 15 days. The fruits developed a respiratory climacteric respiratory patern and remained fit for consumption up to day 6 of storage, that is, without visual symptoms of loss of water and firmness. At this stage, the fruits showed firmness of 117,42 kPa, soluble solids of 6.62º Brix and citric acid of 1.22 %.

Influence of the use of acids and films in post-harvest lychee conservation

Lychee (Litchi chinensis Sonn.) has a high commercial value; however, it has a short shelf-life because of its rapid pericarp browning. The objective of this study was to evaluate the shelf-life of 'Bengal' lychee fruits stored after treatment with hydrochloric acid and citric acid, associated with cassava starch and plastic packaging. Uniformly red pericarp fruits were submitted to treatments: 1-(immersion in citric acid 100 mM for 5 minutes + cassava starch 30 g L-1 for 5 minutes), 2-(immersion in hydrochloric acid 1 M for 2 minutes + starch cassava 30 g L-1 for 5 minutes), 3-(immersion in citric acid 100 mM for 5 minutes + polyvinyl chloride film (PVC, 14 µm thick)) and 4-(immersion in hydrochloric acid 1 M for 2 minutes + PVC film). During 20 days, the fruits were evaluated for mass loss, pericarp color, pH, soluble solids and titratable acidity, vitamin C of the pulp and pericarp and activities of polyphenol oxidase and peroxidase of the pericarp. The treatment with hydrochloric acid associated with PVC was the most effective in maintaining the red color of the pericarp for a period of 20 days and best preservation of the fruit. The cassava starch associated with citric acid, and hydrochloric acid did not reduce the mass loss and did not prevent the browning of lychee fruit pericarp.

Characterization of verdete rock as a potential source of potassium

Potassium is a nutrient found at low levels in Brazilian soils, requiring large inputs of fertilizers to achieve satisfactory crop yields. Brazil has high external dependence and limited reserves of soluble K mineral, which is traditionally exploited for the production of fertilizers. On the other hand, it is common the occurrence in the country of potassium-rich silicate minerals which are not commercially exploited. This study aimed to characterize mineralogically and chemically samples of verdete rock separated into size fractions and evaluate its potential as potassium fertilizer. The mineral composition of verdete rock is based on glauconite, quartz and feldspar. The total K2O content in verdete rock ranged from 5.18 to 9.0 dag/kg. The K content extracted in water or 2% citric acid was 2.4% below the total of K, indicating low reactivity of verdete rock and limitations for direct use as K source. The processes of physical fractionation and sedimentation in water are inefficient to promote the concentration of K in the different verdete rock fractions. The total K content in some samples are considerable and may enable the use of this rock as raw material for production of more reactive potassium fertilizers.

On line pre-concentration for simultaneous determination of low molecular weight organic acids and inorganic anions in Amazonian river water samples employing ion chromatography with conductivity detection

An ion chromatography procedure, employing an IonPac AC15 concentrator column was used to investigate on line preconcentration for the simultaneous determination of inorganic anions and organic acids in river water. Twelve organic acids and nine inorganic anions were separated without any interference from other compounds and carry-over problems between samples. The injection loop was replaced by a Dionex AC15 concentrator column. The proposed procedure employed an auto-sampler that injected 1.5 ml of sample into a KOH mobile phase, generated by an Eluent Generator, at 1.5 mL min-1, which carried the sample to the chromatographic columns (one guard column, model AG-15, and one analytical column, model AS15, with 250 x 4mm i.d.). The gradient elution concentrations consisted of a 10.0 mmol l-1 KOH solution from 0 to 6.5 min, gradually increased to 45.0 mmol l-1 KOH at 21 min., and immediatelly returned and maintained at the initial concentrations until 24 min. of total run. The compounds were eluted and transported to an electro-conductivity detection cell that was attached to an electrochemical detector. The advantage of using concentrator column was the capability of performing routine simultaneous determinations for ions from 0.01 to 1.0 mg l-1 organic acids (acetate, propionic acid, formic acid, butyric acid, glycolic acid, pyruvate, tartaric acid, phthalic acid, methanesulfonic acid, valeric acid, maleic acid, oxalic acid, chlorate and citric acid) and 0.01 to 5.0 mg l-1 inorganic anions (fluoride, chloride, nitrite, nitrate, bromide, sulfate and phosphate), without extensive sample pretreatment and with an analysis time of only 24 minutes.

Estudos químico-agrícolas sôbre o enxofre

1. Analyses of soluble sulphates in 2 N ammonium chloride extracts of 24 samples of soils of the state of São Paulo, Brazil, S. A., showed a sulphur content varying from 0,0013 g per 100 g (found in the b layer of a genuine "terra roxa") to 0,007 g per 100 g of soil (b layer of a soil of depression without definite characteristics). (The results are expressed as elemental sulphur). Determinations of total sulphur in 56 samples of soils of the same state using the method of fusion with sodium carbonate and sodium nitrate revealed 0.007 g of elemental S per 100 g of soil as the lowest value (found in several soil types) and 0.096 g as the highest one (found in the b layer of an ar-quean soil). Apparently soluble sulphates accumulate in the upper layers and total sulphur does the opposite. It was found a strong correlation between total S and carbon content. 2. Under laboratory conditions, in a compost of fresh soil, powdered sulphur and apatite, it was verified after a three months period of incubation that the pH value lowered from 6.30 to 3.23; the citric acid solubility of apatite increased to 271.1 per cent of the original one. Lupinus sp. grown in soil manured with sulphur and apatite has showed fresh and dry weights higher than the plants in control pots; the results are significant at 5% level of probability; phosphorus content is also higher in the manured plants. It was observed a net influence of the apatite plus sulphur treatment on the weight of root nodosities that was four times greater than in the control plants. 3. Nearly five hundred determinations of S, N and P were carried out in 35 species of plants cultivated in the state of São Paulo. A great variation in the amounts of these elements was observed. As a general rule, the leaves contain more sulphur than the stems and roots show the lowest percentages. The conjunct roots and stem of guar (Cyamopsis psoraloides) revealed only 0.019 per cent sulphur; the leaves of kale showed the highest sulphur content, i. e., 2.114%. Apparently there is no correlation between the amounts of S, N and P. The ratio S/N increases from 0.006 (guar) to 0.485 (kale). The ratio S/P, always higher than the corresponding S/N, increases from 0.082 (guar) to 6.381 (older leaves of tomato plants). It is interesting to mention that several among the most important crops in the state of São Paulo namely, cotton, rice, coffee and sugar cane contain more sulphur than phosphorus. 4. Tomato plants cultivated in nutrient solution lacking sulphur showed the following visual symptons of deficiency : chlorosis first in the younger leaves and afterwards in all the leaves; anthocyanin pigments in the petioles and stems; absence of fruits; primary roots stunted and secondary ones longer than in the control plants; stems slender, hard, woody. The histological study of petioles suffering from sulphur deficiency revealed anthocyanin in the parenchyme layer instead of clo-rophyll pigments observed in normal petioles; in the chlorotic leaves the large chloroplasts present only the stroma but the small ones have a little amount of green pigments. Chemical analysis revealed in the abnormal plants : less sulphur and an increased proportion of phosphorus; older leaves contain more sulphur and less phosphorus than the younger ones probably due to physiological difficulties in translocation of sulphur bearing material; increased amount of total N attributed to accumulation of nitrates; marked decrease in ash, sugars and starch; increased proportion of crude fiber and dry material. In the plants suffering from sulphur deficiency photosyntetic rate decreased 34 per cent. 5. Tomato plants were succesfully cultivated in nutrient solution in absence of mineral sulphur but in presence of cysteine. The plants absorbed sulphur, under that form and were able to grow up quite well; the fruiting was normal. In this way rested cleary demonstrated the possibility of absorption of organic sulphur without previous mineralization and its utilization in the building up of protein molecules.

Solubilidade de fosfatos naturais em solução de ácido cítrico a 2%: modificação nas condições de agitação

This paper deals with a modification in the solubilization technique of natural phophates in the 2% citric acid solution. The proposed technique is as follows: 2,5 g of phosphatic material and 250 ml of 2% citric acid solution, in a 500 ml Erlenmeyer flask, are shaken for 30 minutes at 30-40 rpm. The phosphorus (P2O5) was determined by the usual method. The data obtained were compared with the conventional technique in which a Stohmann bottle is used. The natural phosphates used were: Phosphorita de Olinda (Pernambuco), Flórida Phosphate (USA) and Hiperphosphate (África). Statistical analysis was applied to the data and the following conclusions were arrived at: a) The precision is equivalent in both techniques. b) There is no significant variation between the means obtained with the two technique.

Biochemical characterization of a trypanosomatid isolated from the plant Amaranthus retroflexus

A protozoan flagelate has recently been isolated from Amaranthus retroflexus. This plant grows near economically important crops in southeastern Spain, which are known to be parasitized by Phytomonas spp. The present study focuses on the characterization of the energy metabolism of this new isolate. These flagellates utilize glucose efficiently as their primary energy source, although they are unable to completely degrade it. They excrete ethanol, acetate, glycine, and succinate in lower amount, as well as ammonium. The presence of glycosomes was indicated by the early enzymes of the glycolytic pathway, one enzyme of the glycerol pathway (glycerol kinase), and malate dehydrogenase. No evidence of a fully functional citric-acid cycle was found. In the absence of catalase activity, these flagellates showed significant superoxide dismutase activity located in the glycosomal and cytosolic fractions. These trypanosomes, despite being morphologically and metabolically similar to other Phytomonas isolated from the same area, showed significant differences, suggesting that they are phylogenetically different species.

Extractants to assess zinc phytoavailability in mineral fertilizer and industrial by-products

Efficient analytical methods for the quantification of plant-available Zn contained in mineral fertilizers and industrial by-products are fundamental for the control and marketing of these inputs. In this sense, there are some doubts on the part of the scientific community as well as of the fertilizer production sector, whether the extractor requested by the government (Normative Instruction No. 28, called 2nd extractor), which is citric acid 2 % (2 % CA) (Brasil, 2007b), is effective in predicting the plant availability of Zn via mineral fertilizers and about the agronomic significance of the required minimal solubility of 60 % compared to the total content (HCl) (Brasil, 2007a). The purpose of this study was to evaluate the alternative extractors DTPA, EDTA, neutral ammonium citrate (NAC), buffer solution pH 6.0, 10 % HCl, 10 % sulfuric acid, 1 % acetic acid, water, and hot water to quantify the contents of Zn available for maize and compare them with indices of agronomic efficiency of fertilizers and industrial by-products when applied to dystrophic Clayey Red Latosol and Dystrophic Alic Red Yellow Latosol with medium texture. The rate of Zn applied to the soil was 5 mg kg-1, using the sources zinc sulfate, commercial granular zinc, ash and galvanic sludge, ash and two brass slags. Most Zn was extracted from the sources by DTPA, 10 % HCl, NAC, 1% acetic acid, and 10 % sulfuric acid. Recovery by the extractors 2 % CA, EDTA, water, and hot water was low. The agronomic efficiency index was found to be high when using galvanic sludge (238 %) and commercial granular zinc (142 %) and lower with brass slag I and II (67 and 27 %, respectively). The sources galvanizing ash and brass ash showed solubility lower than 60 % in 2 % CA, despite agronomic efficiency indices of 78 and 125 %, respectively. The low agronomic efficiency index of industrial by-products such as brass slag I and galvanizing ash can be compensated by higher doses, provided there is no restriction, as well as for all other sources, in terms of contaminant levels of arsenic, cadmium, chromium, lead, and mercury as required by law (Normative Instruction No 27/2006). The implementation of 2nd extractor 2 % CA and the requirement of minimum solubility for industrial by-products could restrict the use of alternative sources as potential Zn sources for plants.

PHYTOAVAILABILITY OF COPPER IN INDUSTRIAL BY-PRODUCTS AND MINERAL FERTILIZERS

Alternative copper (Cu) sources could be used in fertilizer production, although the bioavailability of copper in these materials is unknown. The objective of this study was to evaluate the extractants neutral ammonium citrate (NAC), 2 % citric acid, 1 % acetic acid, 10 % HCl, 10 % H2SO4, buffer solution pH 6.0, DTPA, EDTA, water, and hot water in the quantification of available Cu content in several sources, relating them to the relative agronomic efficiency (RAE) of wheat grown in a clayey Latossolo Vermelho eutrófico (Oxisol) and Neossolo Quartzarênico (Typic Quartzipsamment). Copper was applied at the rate of 1.5 mg kg-1 as scrap slag, brass slag, Cu ore, granulated copper, and copper sulfate. The extractants 10 % HCl, 10 % H2SO4, and NAC extracted higher Cu concentrations. The RAE values of brass slag and Cu ore were similar to or higher than those of Cu sulfate and granulated Cu. Solubility in the 2nd NAC extractant, officially required for mineral fertilizers with Cu, was lower than 60 % for the scrap slag, Cu ore, and granulated copper sources. This fact indicates that adoption of the NAC extractant may be ineffective for industrial by-products, although no extractant was more efficient in predicting Cu availability for wheat fertilized with the Cu sources tested.