Gerenciamento de resíduos laboratoriais: recuperação de elementos e preparo para descarte final

This work shows some laboratory waste management developed in order to recover some elements or to prepare the waste for a correct final disposal. The 25 elements chosen cover basically all chemical behaviors found for the metals in the Periodic Table. The treatments adopted were based on the classical behavior in aqueous solution (wet chemistry) but an important condition for a full success was the previous knowledge of the qualitative composition of the wastes treated. Some general trends were found: the final liquid waste was always saline and normally presented a higher volume than the original waste; most original wastes were acid in nature; steps such as solid-liquid separation, washing, evaporating and calcining were currently performed. This work was also a very good experience in chemistry in solution for students and showed them the need of treating wastes for a better environment.

Tratamento dos resíduos gerados na síntese de polianilina em escala pré-piloto

Polyaniline (PAni) is one of the most studied conducting polymer. It can be synthesized by two methods: electrochemical or chemical oxidation. The chemical oxidation is more adequate to produce large quantities of polymer. Regardless of the synthesis scale, the treatment of the residues before its final destination is very important and necessary because it contains toxic aniline derivatives (carcinogens in some cases), acids and inorganic salts, both with low toxicity. In this work we discuss the methods used to treat these residues and to eliminate and discard the toxic substances. These were extracted from the reaction residues by using activated coal and the pH of the residue was neutralized.

Reciclagem química de zeólitas comerciais desativadas

Pyro and hydrometallurgical processes were applied to the treatment of spent commercial zeolites (a molecular sieve and a ZSM-5 sample). Both catalysts were employed in pilot plant units. They were kept in their original shape, they were not regenerated and were not subjected neither to mechanical stress nor to overheating zones during their time on-stream. Two recycling processes were tested: (i) direct solubilization of samples in mixtures of HF + H2O2 (60 ºC, 1 h). Although silicon was solubilized, insoluble matter was found in both samples, particularly in the molecular sieve, due to its high amounts of alkaline and alkaline-earth metals; (ii) fusion with KHSO4 (5 h, 600 ºC) with KHSO4/zeolite mass ratio 6:1. After fusion the solid was solubilized in water (100 ºC), leaving silicon as SiO2 residue. In both processes, solubilized metals were isolated by conventional selective precipitation techniques. Analysis of final products by common analytical methods shows that metals present in the original catalysts were recovered with very high yields except when the molecular sieve was treated with HF + H2O2. This reactant mixture proved to be suitable for processing zeolites with a low alkaline and alkaline-earth metal content whereas fusion with KHSO4 appeared to be adequate for all types of zeolites.

Recuperação de bromo em soluções aquosas residuais

A laboratory procedure was devised to recover bromine from waste alkaline aqueous solutions used in the isotopic determination of N-15. The laboratory apparatus comprises two round bottom flasks (1 and 2 L), a dropping funnel, a gas bubbler, a gas regulator and glass fittings. The waste solution is acidified with sulfuric acid forming molecular bromine that is stripped out by a flow of nitrogen gas bubbled through the solution. This gas is then bubbled through a solution of lithium hydroxide generating lithium bromide and lithium hypobromite. The efficiency of bromine recovery was estimated to be 82±2%. This resulting solution was successfully reused in the isotopic determination of N-15. The procedure can recycle most of the bromine used in the laboratory saving resources and preserving the environment. The procedure can be adapted to recover bromine of other laboratory waste streams.

Programa de gerenciamento de resíduos dos laboratórios de graduação da Universidade Regional Integrada do Alto Uruguai e das Missões - Campus Erechim

This work presents a proposal for the management of residues from teaching laboratories. The main goals of the proposal are: scale reduction of experiments, reuse of residues as raw materials for new experiments and appropriate treatment and storage of residues. The methodology includes standardized labels for residue classification and registration of experimental classes and their residues in files. The management seemed to be efficient, resulting in a reduction of the amount of reagents utilized and residues generated, and an increase of reutilization of residues. A considerable decrease of needed storage space and suitable methods for correct residue disposal were achieved. We expect that all laboratories, including those exclusively for research activities, become involved, in a near future, in the Residue Management Project of URI - Campus Erechim.

Tratamento de chorume de aterro sanitário por fotocatálise heterogênea integrada a processo biológico convencional

The chemical and microbiological decomposition of the garbage deposited in landfills leads to the generation of a dark and malodorous liquid residue that shows a chemical composition of extreme variability and complexity. When matured, the leachates show low biodegradability, which makes it difficult to treat by conventional biological processes. In this work a new strategy for the treatment of landfill leachates is proposed, involving a preliminary treatment by heterogeneous photocatalysis followed by an activated sludge system. The results demonstrate that photochemical treatments of 60 and 90 min significantly enhance the leachates' biodegradability favoring subsequent biological treatment. The biodegradability rate (BOD/COD) was also greatly enhanced.

Arqueologia biomolecular: passos preliminares para interpretações sobre a origem dos resíduos orgânicos preservados em fragmentos de cerâmica pré-colonial no Brasil

Organic residue analysis of archaeological potsherds is a well-established method for determining the uses of European and North American pottery vessels. In the present work we assess if the organic residues identified in Brazilian potsherd extracts are related to commodity processes (e.g. cooking or surface treatment) or to other non-archaeological sources, using as a model potsherds recovered from the Rio do Meio site (Santa Catarina Island). The potsherd extracts are dominated by saturated fatty acids (Ac16:0, with lower abundances of Ac14:0 and Ac18:0). Our studies provide evidence that the organic residues preserved in the Brazilian archeological potsherds are related to foodstuffs and surface treatment processes of the pottery vessels.

Recuperação de metais de catalisadores de hidrorrefino usados via fusão com KHSO4

This work describes a process for metal recovery from spent NiMo and CoMo/Al2O3 commercial hydrorefining catalysts. The samples were treated by fusion with potassium hydrogen sulfate (5 h, 600 ºC) with a KHSO4/catalyst mass ratio of 10:1. After fusion the solid was solubilized in water (100 ºC), leaving silicon compounds as residue. Losses of nickel and cobalt may reach 16 wt% of the amount present in the sample, depending on the silicon content. Soluble metals were isolated by selective precipitation techniques (nickel, cobalt, aluminum) or by solvent extraction with methyl-isobutyl ketone (molybdenum) in a hydrochloric acid medium. All metals were recovered in very good yields except for nickel and cobalt in the presence of considerable amounts of silicon. Soluble wastes consist of potassium/sodium sulfates/chlorides. Solid wastes correspond to about 4 wt% of the catalyst and can be discarded in industrial dumps.

Avaliação da reação foto-fenton na decomposição de resíduos de carrapaticida

Experimental procedures based on factorial design and surface response methodology were applied to establishe experimental conditions for the decomposition of a 1:400 (v/v) Supocade® (chlorfenvinphos 13.8% and cypermethrin 2.6%) solution, used to control cattle ticks. Experiments exploring photo-oxidative reactions were performed with and without UV radiation, fixing exposition time and pesticide volume, and varying the oxidant mixture. The use of 3.6 mmol L-1 Fe2+ plus 1.9 mol L-1 H2O2 plus UV radiation provided destruction of 94% of the original carbon content and reduction of aromatic, aliphatic and carbinolic compounds, evaluated by determination of residual carbon content by ICP OES and NMR analysis.

Synthesis, characterization and thermal behaviour of solid-state compounds of benzoates with some bivalent transition metal ions

Solid-state MBz compounds, where M stands for bivalent Mn, Fe, Co, Ni, Cu and Zn and Bz is benzoate, have been synthesized. Simultaneous thermogravimetry and differential thermal analysis (TG-DTA), differential scanning calorimetry (DSC), infrared spectroscopy and complexometry were used to characterize and to study the thermal behaviour of these compounds. The procedure used in the preparation of the compounds via reaction of basic carbonates with benzoic acid is not efficient in eliminating excess acid. However the TG-DTA curves permitted to verify that the binary compounds can be obtained by thermosynthesis, because the benzoic acid can be eliminated before the thermal decomposition of these compounds. The results led to information about the composition, dehydration, thermal stability, thermal decomposition and structure of the isolated compounds. On heating, these compounds decompose in two (Mn, Co, Ni, Zn) or three (Fe, Cu) steps with formation of the respective oxide (Mn3O4, Fe2O3, Co3O4, NiO, CuO and ZnO) as final residue. The theoretical and experimental spectroscopic studies suggest a covalent bidentate bond between ligand and metallic center.

Parâmetros operacionais no processamento de zeólitas desativadas por fusão com KHSO4

This work presents a study on the determination of the optimal experimental conditions for processing spent commercial zeolites in order to recover lanthanide elements and eventually other elements. The process is based on the fusion of the sample with potassium hydrogenosulfate (KHSO4). Three experimental parameters were studied: temperature, reaction time and catalyst/flux mass ratio. After fusion the solid was dissolved in water and the amount of insoluble matter was used to determine the efficiency of the process. The optimized experimental parameters depend on the composition of the sample processed. Under such conditions the insoluble residue corresponds to SiO2. Lanthanide elements and aluminum present in solution were isolated by conventional precipitation techniques; the yields were at least 75 wt%. The final generated wastes correspond to neutral colorless solutions containing alkali chlorides/sulfates and solids that can be disposed of in industrial dumps.

Caracterização dos produtos líquidos e do carvão da pirólise de serragem de eucalipto

This study proposes the low temperature pyrolysis as an alternative conversion process for residual biomass and for obtaining gaseous, liquid and solid chemical feedstocks. Using a bench electrical pyrolysis oven, four product fractions from eucalyptus sawdust were obtained: a gaseous one, two liquid (aqueous and oily), and a solid residue (char). These products were characterized by different analytical methods. The liquid fractions showed themselves as potential sources for input chemicals. The residual char revealed appreciable adsorption capability. The process demonstrated good efficiency, generating at least two fractions of great industrial interest: bio oil and char.

Decomposição térmica de espumas de poliuretano para fabricação de vitrocerâmica celular de Li2O-ZrO2-SiO2-Al2O3 (LZSA)

Characterization of the thermal decomposition of polyurethane (PUR) foams was performed by Fourier-transformed infrared (FT-IR) spectroscopy and thermogravimetric analysis (TGA). Three main weight loss paths were observed by TGA, the residue being lower than 3 wt.% for 3 different PUR foams analyzed. FT-IR spectra indicated CO2, CO, NH3 and isocyanides as main decomposition products. PUR foams of different cell sizes were immersed in a slurry of the parent glass ceramic of composition Li2O-ZrO2-SiO2-Al 2O3 (LZSA) and submitted to heat treatment. The LZSA cellular glass ceramics obtained after sintering and crystallization resembled the original morphology of the PUR foams.

Composição química de um resíduo alcalino da indústria de papel e celulose (DREGS)

Dregs is an alkaline solid by-product generated in the cellulose manufacturing industry that could be used to correct soil acidity. The present study aimed to evaluate the chemical composition of this product and some of its properties. The dregs presented 354 g kg-1 of calcium, neutralization capacity of 80.3%, and pH 10.7, besides low concentration of sodium (10.2 g kg-1), lead (62.9 mg kg-1) and cadmium (5.6 mg kg-1). Thus, it is a product that can safely be used to increase the soil pH.

De resíduo a insumo: a construção do caminho para uma química mais limpa através de um projeto de ensino

The discussion among teachers, students, and technicians about the destination of residues from chemistry laboratories led to a research project whose results were incorporated into a course in its daily practices. The treatment of the residues from argentimetric practices allowed us to establish cognitive relations of technological basis and of those related to the rising of the level of awareness about environmental aspects and social responsibility of chemistry professionals. The techniques and the results, from the economic point of view, namely that of value aggregation (metallic silver) and the conversion of the residue into input (potassium chromate solution) are shown.