Comparison between one-dimensional uncoupled and convection-conduction conjugated approaches in finned surface heat transfer

This work studies the forced convection problem in internal flow between concentric annular ducts, with radial fins at the internal tube surface. The finned surface heat transfer is analyzed by two different approaches. In the first one, it is assumed one-dimensional heat conduction along the internal tube wall and fins, with the convection heat transfer coefficient being a known parameter, determined by an uncoupled solution. In the other way, named conjugated approach, the mathematical model (continuity, momentum, energy and K-epsilon equations) applied to tube annuli problem was numerically solved using finite element technique in a coupled formulation. At first time, a comparison was made between results obtained for the conjugated problem and experimental data, showing good agreement. Then, the temperature profiles under these two approaches were compared to each other to analyze the validity of the one-dimensional classical formulation that has been utilized in the heat exchanger design.

Thermalhydraulic behavior of electrically heated rod during a critical heat flux transient

In nuclear reactors, the occurrence of critical heat flux leads to fuel rod overheating with clad fusion and radioactive products leakage. To predict the effects of such phenomenon, experiments are performed using electrically heated rods to simulate operational and accidental conditions of nuclear fuel rods. In the present work, it is performed a theoretical analysis of the drying and rewetting front propagation during a critical heat flux experiment, starting with the application of an electrical power step from steady state condition. After the occurrence of critical heat flux, the drying front propagation is predicted. After a few seconds, a power cut is considered and the rewetting front behavior is analytically observed. Studies performed with various values of coolant mass flow rate show that this variable has more influence on the drying front velocity than on the rewetting one.

Inverse convection problem of simultaneous estimation of two boundary heat fluxes in parallel plate channels

This paper deals with the use of the conjugate gradient method of function estimation for the simultaneous identification of two unknown boundary heat fluxes in parallel plate channels. The fluid flow is assumed to be laminar and hydrodynamically developed. Temperature measurements taken inside the channel are used in the inverse analysis. The accuracy of the present solution approach is examined by using simulated measurements containing random errors, for strict cases involving functional forms with discontinuities and sharp-corners for the unknown functions. Three different types of inverse problems are addressed in the paper, involving the estimation of: (i) Spatially dependent heat fluxes; (ii) Time-dependent heat fluxes; and (iii) Time and spatially dependent heat fluxes.

Heat Source Estimation with the Conjugate Gradient Method in Inverse Linear Diffusive Problems

In this work, we present the solution of a class of linear inverse heat conduction problems for the estimation of unknown heat source terms, with no prior information of the functional forms of timewise and spatial dependence of the source strength, using the conjugate gradient method with an adjoint problem. After describing the mathematical formulation of a general direct problem and the procedure for the solution of the inverse problem, we show applications to three transient heat transfer problems: a one-dimensional cylindrical problem; a two-dimensional cylindrical problem; and a one-dimensional problem with two plates.

Simulation of Steady-State Nonlinear Heat Transfer Problems Through the Minimization of Quadratic Functionals

In this work it is presented a systematic procedure for constructing the solution of a large class of nonlinear conduction heat transfer problems through the minimization of quadratic functionals like the ones usually employed for linear descriptions. The proposed procedure gives rise to an efficient and easy way for carrying out numerical simulations of nonlinear heat transfer problems by means of finite elements. To illustrate the procedure a particular problem is simulated by means of a finite element approximation.

Effects of condensation in microchannels with a porous boundary: analytical investigation on heat transfer and meniscus shape

In two-phase miniature and microchannel flows, the meniscus shape must be considered due to effects that are affected by condensation and/or evaporation and coupled with the transport phenomena in the thin film on the microchannel wall, when capillary forces drive the working fluid. This investigation presents an analytical model for microchannel condensers with a porous boundary, where capillary forces pump the fluid. Methanol was selected as the working fluid. Very low liquid Reynolds numbers were obtained (Re~6), but very high Nusselt numbers (Nu~150) could be found due to the channel size (1.5 mm) and the presence of the porous boundary. The meniscus calculation provided consistent results for the vapor interface temperature and pressure, as well as the meniscus curvature. The obtained results show that microchannel condensers with a porous boundary can be used for heat dissipation with reduced heat transfer area and very high heat dissipation capabilities.

Primary and secondary development of Cyperus giganteus Vahl rhizome (Cyperaceae)

In Cyperus giganteus, like in other Monocotyledoneae, the protoderm, procambium, fundamental meristem and primary thickening meristem (PTM) are differentiated from the rhizome promeristem. The PTM produces the inner cortical parenchyma, endodermis, pericycle and amphivasal vascular bundles, which are formed by the procambium too. After the primary body differentiates, cellular divisions continue only in the pericycle, and originate an irregular vascular system with vessel elements shorter and more branched than those found in the primary growth. This change of activity in the pericycle defines a secondary growth, where the secondary thickening meristem (STM) is the pericycle itself.

Diversity and structure of the tree community of a fragment of tropical secondary forest of the brazilian Atlantic Forest domain 15 and 40 years after logging

Two adjacent tracts of tropical secondary forest, situated in Itambé do Mato Dentro, south-eastern Brazil, which had been regenerating for 15 and 40 years after clearing, were compared with the purpose of detecting differences in species diversity and composition, species guild composition (regeneration, stratification and dispersion), and stand structure. Four and three 1,125 m² plots laid on the 15- and 40-year-old stands, respectively, sampled 2,430 trees with diameter at the base of the stem > 5 cm. The number of species (S = 199) was high for this forest type and significantly higher for the older stand. Tree density was significantly higher in the younger stand, particularly for smaller trees, whereas the two stands did not differ in both basal area and volume per hectare. Trees of shade-tolerant and understory species were significantly more abundant in the older stand. Though sharing a large proportion of species (49%), the two stands differed significantly in the abundance of many species. Live stumps probably contributed to the relatively quick restoration of some forest characteristics, particularly species diversity, basal area and volume.

Patterns of litter production in a secondary alluvial Atlantic Rain Forest in southern Brazil

Above-ground litter production is one of the most accessible ways to estimate ecosystem productivity, nutrient fluxes and carbon transfers. Phenological patterns and climatic conditions are still not fully explained well for tropical and subtropical forests under less pronounced dry season and non-seasonal climates, as well as the interaction of these patterns with successional dynamics. Monthly litterfall was estimated for two years in a 9 to 10 year old secondary alluvial Atlantic Rain forest. Total litterfall was higher in the site with more developed vegetation (6.4 ± 1.2 ton ha-1 year-1; 95% confidence interval) as compared to the site with less developed vegetation (3.0 ± 1.0 ton ha-1 year-1). The monthly production of 11 litter fractions (eight fractions comprising the leaf litter of the seven main species of the community and other species; reproductive parts, twigs £ 2 cm diameter, and miscellaneous material) were correlated with meteorological variables making possible to identify three patterns of deposition. The main pattern, dominated by leaf-exchanging species, consisted of a cycle with the highest litterfall at the beginning of the rainy season, preceding by basically three months the peaks of the annual cycles of rainfall and temperatures. Other two patterns, dominated by brevi-deciduous species, peaked at the end of the rainy season and at the end of the non-rainy season. Tropical and subtropical dry forests that present the highest leaf fall gradually earlier than rain forests (as the studied sites) are possibly related to the start of senescence process. It seems that such process is triggered earlier by a more severe hydric stress, besides other factors linked to a minor physiological activity of plants that result in abscission.

Chromosome number and secondary constriction variation in 51 accessions of a citrus germplasm bank

The mitotic chromosomes of 51 citrus accessions from the Centro Nacional de Pesquisa em Mandioca e Fruticultura Tropical, Cruz das Almas, BA, Brazil, were analyzed. The sample included representatives of 20 Citrus species, one of Poncirus and seven hybrids. All accessions showed 2n = 18 without any evidence of numerical variation. The most clearly variable karyotype feature was the number and position of secondary constrictions (SECs). In 19 accessions the SECs were not identified, mainly due to the degree of chromatin condensation. In the remainder they varied in number from one to three per karyotype. They were found in the proximal region of one of the three largest chromosome pairs, in the terminal/subterminal region of a smaller chromosome or, more seldom, terminally in a larger chromosome. Only in a few cases were such constrictions observed simultaneously in both homologues of the same chromosome pair. The high variability of this karyotype feature may be due to the activation of this region in the previous interphase but may also indicate a high structural variability and heterozygosity of citrus germplasms

Nutritional status of hemodialysis patients with secondary hyperparathyroidism

The repercussions of secondary hyperparathyroidism on the nutritional status of chronic renal failure patients have not been well established. Therefore, the aim of this study was to compare the nutritional indices of hemodialysis patients with and without secondary hyperparathyroidism. Sixteen hemodialysis patients with serum parathyroid hormone (PTH) levels higher than 420 pg/ml (hyperparathyroidism group) were matched for gender, age and length of dialysis treatment to 16 patients with serum PTH between 64 and 290 pg/ml (control group). The following parameters were assessed: anthropometric indices (body mass index, skinfold thickness, midarm muscle circumference and body fat), 4-day food diaries, protein catabolic rate, biochemical indices (blood urea nitrogen, serum creatinine, albumin, ionized calcium, inorganic phosphorus, serum alkaline phosphatase, PTH, pH and HCO3) and dialysis efficiency. We did not observe differences in the anthropometric indices between the two groups. Only calcium intake was significantly different between groups (307.9 mg/day for the hyperparathyroidism group vs 475.8 mg/day for the control group). Protein catabolic rate tended to be higher in the hyperparathyroidism group compared to the control group (1.3 vs 0.9 g kg-1 day-1; P = 0.08). Except for blood urea nitrogen (86.4 vs 75.7 mg/dl), alkaline phosphatase (175 vs 65 U/l) and PTH (898 vs 155 pg/ml), no other differences were found between groups in the biochemical indices studied. PTH was directly correlated with protein catabolic rate (r = 0.61; P<0.05) and length of dialysis (r = 0.53; P<0.05) only in the hyperparathyroidism group. Considering the indices used, we could not demonstrate the deleterious effect of high PTH levels on the nutritional status of hemodialysis patients. Indirect evidence, however, suggests an action of PTH on protein metabolism.

Gliclazide and bedtime insulin are more efficient than insulin alone for type 2 diabetic patients with sulfonylurea secondary failure

To determine the effects of combined therapy of gliclazide and bedtime insulin on glycemic control and C-peptide secretion, we studied 25 patients with type 2 diabetes and sulfonylurea secondary failure, aged 56.8 ± 8.3 years, with a duration of diabetes of 10.6 ± 6.6 years, fasting plasma glucose of 277.3 ± 64.6 mg/dl and a body mass index of 27.4 ± 4.8 kg/m². Patients were submitted to three therapeutic regimens lasting 2 months each: 320 mg gliclazide (phase 1), 320 mg gliclazide and bedtime NPH insulin (phase 2), and insulin (phase 3). At the end of each period, glycemic and C-peptide curves in response to a mixed meal were determined. During combined therapy, there was a decrease in all glycemic curve values (P<0.01). Twelve patients (48%) reached fasting plasma glucose <140 mg/dl with a significant weight gain of 64.8 kg (43.1-98.8) vs 66.7 kg (42.8-101.4) (P<0.05), with no increase in C-peptide secretion or decrease in HbA1. C-Peptide glucose score (C-peptide/glucose x 100) increased from 0.9 (0.2-2.1) to 1.3 (0.2-4.7) during combined therapy (P<0.01). Despite a 50% increase in insulin doses in phase 3 (12 U (9-30) vs 18 U (11-60); P<0.01) only 3 patients who responded to combined therapy maintained fasting plasma glucose <140 mg/dl (P<0.02). A tendency to a higher absolute increase in C-peptide (0.99 (0.15-2.5) vs 0.6 (0-2.15); P = 0.08) and C-peptide incremental area (2.47 (0.22-6.2) vs 1.2 (0-3.35); P = 0.07) was observed among responders. We conclude that combined therapy resulted in a better glucose response to a mixed meal than insulin alone and should be tried in type 2 diabetic patients before starting insulin monotherapy, despite difficulties in predicting the response.

Circulating forms of parathyroid hormone detected with an immunofluorometric assay in patients with primary hyperparathyroidism and in hyperparathyroidism secondary to chronic renal failure

In patients with uremia, intact parathyroid hormone (PTH) measurement appears to overestimate the biologically active hormone in circulation. The recent description of the accumulation in these patients of a non-intact PTH form measured by the standard immunometric assays, re-opened the question. In this study we submitted serum samples from 7 patients with primary hyperparathyroidism (PHP) and from 10 patients with hyperparathyroidism secondary to chronic renal failure (SHP) to preparative HPLC in order to discriminate the molecular forms measured by our currently used immunofluorometric assay for intact PTH. The elution profile obtained with the HPLC system showed two clearly defined peaks, the first one corresponding to a lower molecular weight form, and the second to the intact PTH (1-84) form. In patients with SHP the area under the curve for the first peak (mean 29.5%, range 20.6 to 40.4%) was significantly greater than that observed for patients with PHP (mean 15.6%, range 5.6 to 21.9%). This confirms previous studies showing accumulation of molecular forms of slightly lower molecular weight, presumably PTH (7-84), in patients with SHP and, to a lesser extent, in patients with PHP. The real necessity of assays that discriminate between these two molecular forms is debatable.

The use of protein structure/activity relationships in the rational design of stable particulate delivery systems

The recombinant heat shock protein (18 kDa-hsp) from Mycobacterium leprae was studied as a T-epitope model for vaccine development. We present a structural analysis of the stability of recombinant 18 kDa-hsp during different processing steps. Circular dichroism and ELISA were used to monitor protein structure after thermal stress, lyophilization and chemical modification. We observed that the 18 kDa-hsp is extremely resistant to a wide range of temperatures (60% of activity is retained at 80ºC for 20 min). N-Acylation increased its ordered structure by 4% and decreased its ß-T1 structure by 2%. ELISA demonstrated that the native conformation of the 18 kDa-hsp was preserved after hydrophobic modification by acylation. The recombinant 18 kDa-hsp resists to a wide range of temperatures and chemical modifications without loss of its main characteristic, which is to be a source of T epitopes. This resistance is probably directly related to its lack of organization at the level of tertiary and secondary structures.

Heat storage rate and acute fatigue in rats

Thermal environmental stress can anticipate acute fatigue during exercise at a fixed intensity (%VO2max). Controversy exists about whether this anticipation is caused by the absolute internal temperature (Tint, ºC), by the heat storage rate (HSR, cal/min) or by both mechanisms. The aim of the present study was to study acute fatigue (total exercise time, TET) during thermal stress by determining Tint and HSR from abdominal temperature. Thermal environmental stress was controlled in an environmental chamber and determined as wet bulb globe temperature (ºC), with three environmental temperatures being studied: cold (18ºC), thermoneutral (23.1ºC) or hot (29.4ºC). Six untrained male Wistar rats weighing 260-360 g were used. The animals were submitted to exercise at the same time of day in the three environments and at two treadmill velocities (21 and 24 m/min) until exhaustion. After implantation of a temperature sensor and treadmill adaptation, the animals were submitted to a Latin square experimental design using a 2 x 3 factorial scheme (velocity and environment), with the level of significance set at P<0.05. The results showed that the higher the velocity and the ambient temperature, the lower was the TET, with these two factors being independent. This result indicated that fatigue was independently affected by both the increase in exercise intensity and the thermal environmental stress. Fatigue developed at different Tint and HSR showed the best inverse relationship with TET. We conclude that HSR was the main anticipating factor of fatigue.