A poluição gerada por máquinas de combustão interna movidas à diesel - a questão dos particulados. Estratégias atuais para a redução e controle das emissões e tendências futuras

The exhaust emissions of vehicles greatly contribute to environmental pollution. Diesel engines are extremely fuel-efficient. However, the exhaust compounds emitted by diesel engines are both a health hazard and a nuisance to the public. This paper gives an overview of the emission control of particulates from diesel exhaust compounds. The worldwide emission standards are summarized. Possible devices for reducing diesel pollutants are discussed. It is clear that after-treatment devices are necessary. Catalytic converters that collect particulates from diesel exhaust and promote the catalytic burn-off are examined. Finally, recent trends in diesel particulate emission control by novel catalysts are presented.

Influência do agente precipitante na preparação do óxido de nióbio (V) hidratado pelo método da precipitação em solução homogênea

This work reports the preparation, characterization and study of the ion exchange behavior of hydrous niobium oxide prepared by a homogeneous precipitation method. The precipitating agent was obtained in aqueous solution by thermal decomposition of urea or ammonium carbonate. The compounds were chemically and physically characterized by X-ray diffractometry, thermal analysis (TG/DTG), surface area measurements and ion exchange behavior with sodium. The materials prepared with ammonium carbonate presented a higher degree of crystallinity and better ion exchange capacity with sodium than materials prepared with urea. In the homogeneous precipitation method, materials were obtained with specific surface area of 123 - 224 m² g-1. A variation of the preparation process produced hydrous niobium oxide with a different degree of hydration and specific surface area. This provided materials with different physico-chemical properties.

Composição química da precipitação atmosférica no sul do Brasil: estudo preliminar

The present work is a preliminary study of total and wet precipitation in the Candiota region, RS. The samples were collected from January to June 2001 at four different sites. The following variables were analysed: pH, conductivity, alkalinity, Cl-, NO3-, F-, SO4(2-), Na+, K+, Mg2+, NH4+, Ca2+ and Zn, Cu, Fe, Al, Mn. The results showed slightly acidic precipitation and higher concentrations of NH4+, Na+, Cl- and SO4(2-). Factor analysis applied to the variables studied allowed identifying the major sources. Na+, Cl- and Mg2+ have their origin in sea salts and NH4+, Ca2+, K+, SO4(2-) and NO3- are from local anthropogenic sources.

Avaliação da padronização interna em espectrometria de absorção atômica utilizando gráficos de correlação

The use of an internal standard (IS) in ET AAS can be considered a new trend after the commercial introduction of a simultaneous spectrometer. The evaluation of experimental data to choose the most appropriate IS can be done by comparing correlation graphs. They were used to verify the resemblance among the simultaneous measurements obtained for the analyte(s) and the IS by inductively coupled plasma optical emission spectrometry (ICPOES). The judicious selection of IS by using correlation graphs for determinations by ET AAS can be exploited to improve the precision and accuracy of the analytical results. Therefore, a new approach for studying the use of IS in ET AAS is presented.

Utilização de um eletrodo de grafite-epóxi recoberto com [Zn(FEN)3][tetratris(4-clorofenil) borato]2 sensível a zinco(II) em meio 1,10-fenantrolina como eletrodo indicador em titulações potenciométricas de precipitação

The construction and analytical evaluation of a coated graphite-epoxy electrode sensitive to the zinc-1,10-phenantroline complex based on the [Zn(fen)3][tetrakis(4-chlorophenyl)borate]2 incorporated into a poly(vinylchloride) (PVC) matrix are described. A thin membrane film of this ion-pair, dibutylphthalate (DBPh) and PVC were deposited directly onto an electrically conductive graphite-epoxy support located inside a Perspex® tube. The best PVC polymeric membrane contains 65% (m/m) DBPh, 30% (m/m) PVC and 5% (m/m) of the ion-pair. This electrode shows a response of 19.5 mV dec-1 over the zinc(II) concentration range of 1.0 x 10-5 to 1.0 x 10-3 mol L-1 in 1,10-phenantroline medium, at pH 6.0. The response time was less than 20 seconds and the lifetime of this electrode was more than four months (over 1200 determinations by each polymeric membrane). It was successfully used as an indicator electrode in the potentiometric precipitation titration of zinc(II) ions.

Adsorção de íons dicromato nos compósitos celulose/ZrO2.nH2O preparados pelos métodos da precipitação convencional e em solução homogênea

This article describes the preparation and characterization of the cellulose/ hydrated zirconium oxide composites prepared by conventional precipitation (PC) and homogeneous solution precipitation (PSH) methods. The composite obtained by the PC method was prepared by using an ammonia solution as the precipitating agent, while the composite obtained by the PSH method was prepared by using urea as the precipitating agent. The adsorption of dichromate ions on the composites was studied using factorial design 2³. The variables were: initial concentration, agitation time and mass of the composite. The data obtained agree better for the composite obtained by the PC method.

Análise por cromatografia gasosa de BTEX nas emissões de motor de combustão interna alimentado com diesel e mistura diesel-biodiesel (B10)

This paper describes the procedures for analysing pollutant gases emitted by engines, such as volatile organic compounds (benzene, toluene, ethylbenzene, o-xylene, m-xylene and p-xylene) by using high resolution gas chromatography (HRGC). For IC engine burning, in a broad sense, the use of the B10 mixture reduces drastically the emissions of aromatic compounds. Especially for benzene the reduction of concentrations occurs at the level of about 24.5%. Although a concentration value below 1 µg mL-1 has been obtained, this reduction is extremely significant since benzene is a carcinogenic compound.

Avaliação das técnicas de precipitação química e encapsulamento no tratamento e destinação conjunta de resíduos líquidos contendo cromo e vidrarias de laboratório

In this paper, we present procedures for the treatment and final disposal of residual solutions containing chromium, in order to evaluate the effectiveness of chemical precipitation of the metal and the potential of the glass encapsulation technique, using broken laboratory glassware. The results demonstrated that pH-values convenient for chemical precipitation are between 10 - 11. With regard to Cr(OH)3 encapsulation, the leaching and solubilization tests allowed to classify the waste as non-dangerous and non-inert. Finally, it is pointed out that the adoption of waste management practices in universities should be encouraged, helping to train professionals skilled in good laboratory practices.

Adsorção de chumbo, cádmio e prata em óxido de nióbio (V) hidratado preparado pelo método da precipitação em solução homogênea

This paper describes the adsorption of heavy metals ions from aqueous solution by hydrous niobium oxide. Three heavy metals were selected for this study: cadmium, lead and silver. Adsorption isotherms were well fitted by Langmuir model. Maximum adsorption capacity (Q0) for Pb2 +, Ag+ and Cd2 + was found to be 452.5, 188.68 and 8.85 mg g-1, respectively.

Precipitação seletiva de tamanhos em nanopartículas semicondutoras coloidais de CdTe e CdSe: um estudo por espectroscopia UV-VIS

The post-preparative size-selective precipitation technique was applied in CdTe and CdSe semiconductor nanocrystals prepared via colloidal route in water. The synthesis of CdTe and CdSe nanoparticles and the effect of the post-preparative size-selective precipitation have been characterized mainly by mean of ultraviolet and visible absorption spectroscopy (UV-Vis). It was demonstrated that the size-selective precipitation are able to isolate particles of different sizes and purify the nanoparticles as well.

Composição química da precipitação úmida da região metropolitana de Porto Alegre, Brasil, 2005- 2007

This work aims to quantify the wet precipitation the Metropolitan Area of Porto Alegre (MAPA), in southern Brazil, through the analysis of major ions (by ion chromatography) and metallic elements (ICP/AES). By principal components analysis and cluster analysis was possible to identify the influence of natural and anthropic sources in wet precipitation. The results indicated of the higher contribution to the ions NH4+, SO4(2-) and Ca2+. Thus it was possible to identify the contribution of anthropogenic sources in wet precipitation in the study area, such as power plants, oil refineries, steel and vehicle emissions.

Influência de adições de prata na cinética de precipitação da liga Cu-5%Al

A influência de adições de 2%, 4%, 6%, 8% e 10% de prata, em massa, na cinética de formação e precipitação de precipitados ricos em prata, na liga Cu-5% Al foi estudada através de medidas de variação da microdureza com a temperatura e o tempo. Os resultados obtidos indicaram que a presença da prata aumenta consideravelmente a dureza da liga e também interfere na cinética de precipitação, com uma mudança mecanística no processo que está relacionada com o teor de prata das ligas.

Pressão interna e refração molar dos sistemas dimetilsulfóxido + tiofeno, dimetilsulfóxido + piridina a 298,15K

Pressão interna, volume livre, refração molar e propriedades termodinâmicas de excesso de misturas líquidas binárias de dimetil sulfóxido + tiofeno e dimetil sulfóxido + piridina a 298.15K foram calculadas a partir de medidas experimentais de densidades, tensão superficial e índice de refração. A relação entre a pressão interna, volume molar de excesso, refração molar, e a interação molecular dos sistemas binários é examinada.

Comparação do ajuste dos modelos de morgan-mercer-flodin e de johnson-mehl-avrami na reação de precipitação na liga cu-3%al-5%ag

Em geral, os modelos de crescimento empregados na descrição de processos cinéticos do estado sólido utilizam as funções de Morgan-Mercer-Flodin (MMF) e Johnson-Mehl-Avrami (JMA). Neste trabalho comparou-se o comportamento das estimativas dos parâmetros dessas funções, em duas parametrizações, quando ajustadas aos dados experimentais de variação isotérmica da microdureza da liga Cu-3%Al-5%Ag com o tempo de envelhecimento, em cinco temperaturas diferentes. Na estimativa dos parâmetros aplicou-se o método dos mínimos quadrados à função linearizada do modelo e para o refinamento da solução, os procedimentos da regressão não linear. Foram obtidas as distribuições de freqüências das estimativas dos parâmetros, por simulação, e determinados seus erros relativos. Observou-se que, em uma das parametrizações das funções, a estimativa do parâmetro cinético apresentou maior estabilidade. Apesar dessas funções serem anteriormente consideradas distintas, verificou-se que a função de MMF é uma aproximação da função de JMA, sendo que esta, com a parametrização adequada, é a mais indicada para descrever o processo cinético considerado.