Mechanical properties of castor beans subject to different drying temperatures aiming to disrupt the bean coat

In castor oil extraction process, the bean coat is abrasive to the equipment and releases substances that modify the oil color, reducing its quality. A potential solution would be to run the extraction by compressing only the endosperm. Due to lack of information, the objective of this study was to evaluate the influence of forced air drying at 40, 60, 80 and 100 ºC and farmyard drying, in the mechanical properties of the beans, aiming to break the bean coat. Castor beans were subjected to compression tests, in two perpendicular directions, at a strain rate of 0.6 mm.s-1. Average values of force, deformation energy, strain, all at rupture, and stiffness were used to evaluate the effects of dehydration. It was observed that the heat treatments did not alter the mechanical properties of castor beans, the strain and stiffness values discriminate the differences between the directions and had the lowest coefficients of variation. It was concluded that forced air drying, more costly than farmyard drying, does not bring benefits to the decortication. However, regardless the heat treatment used, the mechanical stress lengthwise is the most suitable to promote decortication.

Yam (Discorea sp) drying with different cuts and temperatures: experimental and simulated results

The yam (Discorea sp) is a tuber rich in carbohydrates, vitamins and mineral salts, besides several components that serve as raw material for medicines. It grows well in tropical and subtropical climates and develops well in zones with an annual pluvial precipitation of around 1300mm, and with cultural treatments, its productivity can exceed 30t/ha. When harvested, the tubers possess about 70% of moisture, and are merchandised "in natura", in the atmospheric temperature, which can cause its fast deterioration. The present work studied the drying of the yam in the form of slices of 1.0 and 2.5cm thickness, as well as in the form of fillets with 1.0 x 1.0 x 5.0cm, with the drying air varying from 40 to 70°C. The equating of the process was accomplished, allowing to simulate the drying as a function of the conditions of the drying air and of the initial and final moisture of the product. Also investigated was the expense of energy as function of the air temperature. The drying in the form of fillets, with the air in a temperature range between 45 and 50°C, was shown to be the most viable process when combining both the quality of the product and the expense of energy.

Storage of Tabebuia caraiba (Mart.) Bureau seeds in different packaging and temperatures

Tabebuia caraiba (Mart.) Bureau, commonly known as Silver Trumpet Tree is a forestal species, belonging to Bignoniaceae family, which can be utilized as medicinal plant or in landscaping of urban and rural areas; besides producing large mechanical resistance wood. Despite its wide use and ecological importance, basic studies on storages of their seeds are scarce. This way, the objective of this study was to determine the most adequate packaging and the best temperatures, for storing seeds of T. caraiba. For this, seeds were stored in two types of packaging: Kraft paper bags and transparent polyethylene bags; which were then stored during 150 days under three different environments: laboratory normal environment (25±2 °C); cold chamber (8±2 °C); and refrigerator (6±2 °C). After periods of 0, 30, 60, 90, 120, and 150 days, seed moisture content, percentage of emergence, emergence speed index, and seedling length were evaluated. Seeds of T. caraiba kept in packaging of paper and polyethylene bags and stored at laboratory environmental condition, have lost more quickly their vigor along the storage period. For storage, it is recommended the maintenance of T. caraiba seeds in polyethylene bags into cold chamber; and/or polyethylene bags or Kraft paper bags into refrigerator.

LABORATORY EVALUATION OF THE DEVELOPMENT OF Aedes aegypti IN TWO SEASONS: INFLUENCE OF DIFFERENT PLACES AND DIFFERENT DENSITIES

Aedes aegypti is an important vector in Brazil being the main vector of the dengue-fever. This paper employs survival curves to describe the time in days from larvae to adult forms of Aedes aegypti raised, individually and collectively, and compares it during winter and spring when positioned inside and outside a laboratory. The study was conducted in São Vicente, a coastal city in Southeastern Brazil. The lowest water temperature in winter and in spring was 20 °C and the highest was 26 °C in spring. Higher and more stable temperatures were measured in the intra compared to the peri in both seasons. Consequently, larvae positioned in the intra resulted in the lowest median time to develop in the individual and collective experiment (nine and ten days, respectively). At least 25% of the larvae positioned in the intra in the individual experiment in the spring took only seven days to reach adulthood. Sex ratios and the median time development by sex did not show significant differences. These results indicate that efforts to control Aedes aegypti must be continuous and directed mainly to prevent the intra-domiciliary sites that can be infested in a week in order to reduce the human-vector contact.

Effects of light and temperature on isoprene emission at different leaf developmental stages of eschweilera coriacea in central Amazon

Isoprene emission from plants accounts for about one third of annual global volatile organic compound emissions. The largest source of isoprene for the global atmosphere is the Amazon Basin. This study aimed to identify and quantify the isoprene emission and photosynthesis at different levels of light intensity and leaf temperature, in three phenological phases (young mature leaf, old mature leaf and senescent leaf) of Eschweilera coriacea (Matamatá verdadeira), the species with the widest distribution in the central Amazon. In situ photosynthesis and isoprene emission measurements showed that young mature leaf had the highest rates at all light intensities and leaf temperatures. Additionally, it was observed that isoprene emission capacity (Es) changed considerably over different leaf ages. This suggests that aging leads to a reduction of both leaf photosynthetic activity and isoprene production and emission. The algorithm of Guenther et al. (1999) provided good fits to the data when incident light was varied, however differences among E S of all leaf ages influenced on quantic yield predicted by model. When leaf temperature was varied, algorithm prediction was not satisfactory for temperature higher than ~40 °C; this could be because our data did not show isoprene temperature optimum up to 45 °C. Our results are consistent with the hypothesis of the isoprene functional role in protecting plants from high temperatures and highlight the need to include leaf phenology effects in isoprene emission models.

Effect of temperature on different stages of Romanomermis iyengari, a mermithid nematode parasite of mosquitoes

The effect of temperature (20 degrees-35 degrees C) on different stages of Romanomermis iyengari was studied. In embryonic development, the single-cell stage eggs developed into mature eggs in 4.5-6.5 days at 25-35 degrees C but, required 9.5 days at 20 degrees C. Complete hatching occurred in 7 and 9 days after egg-laying at 35 and 30 degrees C, respectively. At 25 and 20 degrees C, 85-96 of the eggs did not hatch even by 30th day. Loss of infectivity and death of the preparasites occurred faster at higher temperatures. The 50 survival durations of preparasites at 20 and 35 degrees C were 105.8 and 10.6 hr respectively. They retained 50 infectivity up to 69.7 and 30.3 hr. The duration of the parasitic phase increased as temperature decreased. Low temperature favoured production of a higher proportion of females which were also larger in size. The maximum time taken for the juveniles to become adults was 14 days at 20 degrees C and the minimum was 9 days at 35 degrees C. Oviposition began earlier at higher temperature than at lower temperature. However, its fecundic period was shorter at 20 degrees C than at 35 degrees C indicating enhanced rate of oviposition at 20 degrees C. Fecundity was adversely affected at 20 degrees C and 35 degrees C. It is shown that the temperature range of 25 degrees-30 degrees C favours optimum development of R. iyengari.

Principal components analysis for quality evaluation of cooled banana 'Nanicão' in different packing

This work aims determinate the evaluation of the quality of 'Nanicão' banana, submitted to two conditions of storage temperature and three different kinds of package, using the technique of the Analysis of Principal Components (ACP), as a basis for an Analysis of Variance. The fruits used were 'Nanicão' bananas, at ripening degree 3, that is, more green than yellow. The packages tested were: "Torito" wood boxes, load capacity: 18 kg; "½ box" wood boxes, load capacity: 13 kg; and cardboard boxes, load capacity: 18 kg. The temperatures assessed were: room temperature (control); and (13±1ºC), with humidity controlled to 90±2,5%. Fruits were discarded when a sensory analysis determined they had become unfit for consumption. Peel coloration, percentages of imperfection, fresh mass, total acidity, pH, total soluble solids and percentages of sucrose were assessed. A completely randomized design with a 2-factorial treatment structure (packing X temperature) was used. The obtained data were analyzed through a multivariate analysis known as Principal Components Analysis, using S-plus 4.2. The conclusion was that the best packages to preserve the fruit were the ½ box ones, which proves that it is necessary to reduce the number of fruits per package to allow better ventilation and decreases mechanical injuries and ensure quality for more time.

Evaluation of winter temperatures on apple budbreak using grafted twigs

Temperature is the main climate factor related to induction, maintenance and dormancy release in apple (Malus domestica Borkh.). The inadequate chilling exposure in apples causes budbreak problems, resulting in decrease in yield potential. Thus, the knowledge of physiological principles and environmental factors determining the dormancy phenomenon, especially winter temperature effects, it is necessary for the efficient selection of cultivars in a productive region. In addition, it is indispensable to adapt the orchard management aiming to decrease the problems caused by lack chilling during winter. The objective of this study was to evaluate the influence of different thermal conditions during the dormancy period on budbreak of apple cultivars. One-year-old twigs of 'Castel Gala' and 'Royal Gala' cultivars, grafted on M7 rootstock, were submitted to temperatures of 5, 10 and 15ºC for different exposure periods (168; 336; 672; 1,008 and 1,344 hours). After treatments execution, the plants were kept in a greenhouse at 25ºC. Budbreak was quantified when accumulated 3,444; 6,888; 10,332; 13,776; 17,220 and 20,664 GDHºC after temperature treatments. The cultivars responded differently to temperature effect during the winter period. The temperature of 15ºC during winter shows a greater effectiveness on 'Castel Gala' apple budbreak while in the 'Royal Gala' apples the temperatures of 5 and 10ºC show better performance. 'Castel Gala' cultivar (low chilling requirement) may supply its physiological necessities, may be capable to budburst, even when subjected to higher temperatures in relation to 'Royal Gala' apples (high chilling requirement).

Temporal progress of southern rust in maize under different environmental conditions

The progress of the severity of southern rust in maize (Zea mays) caused by Puccinia polysora was quantified in staggered plantings in different geographical areas in Brazil, from October to May, over two years (1995-1996 and 1996-1997). The logistic model, fitted to the data, better described the disease progress curves than the Gompertz model. Four components of the disease progress curves (maximum disease severity; area under the disease progress curve, AUDPC; area under the disease progress curve around the inflection point, AUDPCi; and epidemic rate) were used to compare the epidemics in different areas and at different times of planting. The AUDPC, AUDPCi, and the epidemic rate were analyzed in relation to the weather (temperature, relative humidity, hours of relative humidity >90%, and rainfall) and recorded during the trials. Disease severity reached levels greater than 30% in Piracicaba and Guaíra in the plantings between December and January. Lower values of AUDPC occurred in later plantings at both locations. The epidemic rate was positively correlated (P < 0.05) with the mean daily temperatures and negatively correlated with hours of relative humidity >90%. The AUDPC was not correlated with any weather variable. The AUDPCi was negatively related to both variables connected to humidity, but not to rain. Long periods (mostly >13 h day-1) of relative humidity >90% (that corresponded to leaf wetness) occurred in Castro. Severity of southern rust in maize has always been low in Castro, thus the negative correlations between disease and the two humidity variables.

Physiological quality of Gliricidia sepium (Jacq.) Steud. (Leguminosae - Papilionoideae) seeds subjected to different storage conditions

Studies of seed physiological processes represent the starting point for the sustainable utilization of native or cultivated plant species from the caatinga biome for which germination studies are still scarce. In order to determine adequate methods for the conservation of Gliricidia sepium seeds, the physiological quality of propagules exposed to different conditions and times of storage were examined. Recently collected seeds of G. sepium were analyzed immediately, while the other sample was stored for three, six, nine, or twelve months in plastic or paper bags under refrigeration or at room temperature for further analysis. The germination rates of seeds from each storage regime were determined and these rates compared to their water content. It was observed that germination capacity was directly related to changes in seed humidity. Storing seeds in plastic bags yielded the best conservation, mainly when they were stored at low temperatures. However, even at temperatures near 25°C it was possible to prolong seed viability when their water content was controlled through the use of impermeable packing.

Potentials of biogas production from young bulls manure fed with different diets

Physical and chemical characteristics of manure are modified by different animal production systems. In cattle feeding system for young bulls there is an inversion of the proportion between forage and concentrate. In other words, the animals receive a smaller amount of forage compared to the traditional system. These changes in the manure characteristics involve changes in the treatment systems. The aim of this study was to determine the potential production of biogas of batch digesters fed with manure from young bulls that received two diets containing different proportions between forage and concentrate, with or without inoculums and submitted to three levels of temperature (25, 35 and 40(0)C). The evaluated parameters were total solids (TS) and volatile solids (VS) reduction and biogas potentials production. The digesters fed with manure from animals that received the diet 2 (80%C + 20% R) showed the largest reductions of TS and VS. About the potentials of biogas production there was interaction between the factors diet and inoculums, but no effects of temperatures. The treatment content manure from animals fed with diet 2 without inoculums presented the greatest potential of biogas production per kg of TS added (0.2123 m³).

Impact of different light sources on broiler rearing environment

Broiler production is highly dependent on the use of artificial light. The light source may affect the effectiveness of housing conditions due to increasing ambient temperature and concentration of noxious gases. This research aimed to evaluate the effects of different bulb types on the thermal, aerial, and acoustic environment of broiler aviaries. The experiment was carried out at a commercial broiler farm in Dourados, Mato Grosso do Sul State, Brazil. Three aviaries were used, and two flocks of male broilers from Cobb® genetic strain were reared from the first day to slaughter. Each aviary was equipped with a different light source, comprising the adopted treatments (A1 - incandescent light bulb, control; A2 - sodium vapor light bulb; A3 - fluorescent light bulb). The aviaries were divided into nine quadrants, and the environmental data (ambient dry bulb temperature and relative humidity), litter surface temperature, CO2 and NH3 concentrations, and bird sound pressure behavior were recorded in each quadrant. The aviary with incandescent light presented higher air and litter temperatures, and concentration of gases than the other tested alternatives. It also presented higher level of sound pressure in the second week of the growing period; however, from this period up to slaughter, there was no effect of the light source on the results of broiler sound pressure level.

Internal ambience of beehives Apis mellifera with different colors and roofing materials in the sub middle of the São Francisco Valley

ABSTRACTThe current study aimed to evaluate the influence of three colors and two types of roofing materials under the internal temperature of bee colonies Apis mellifera. The experiment was conducted at the Agricultural Sciences Campus at the Federal University of Sao Francisco Valley located in Petrolina-PE, in November and December 2013, using 24 colonies housed in Langstroth hives. The experiment was a completely randomized factorial design (3x2) with three colors of box (blue, white, and traditional) and two types of cover (with and without the use of plaster) with six treatments and four replications. The internal temperature dates of the colonies were hourly recorded, during 24 hours, and surface temperatures were hourly recorded between 08h00 and 17h00. The highest values for surface and internal temperature were registered in the blue painted boxes without the use of plasterboard, and the blue painted boxes covered with plasterboard respectively. However, the lowest values ​​were found in the white painted hives and hives that have not received the plasterboard. It is recommended to paint boxes with bright colors, and the use of plasterboard had no effect in reducing the internal temperature.

Germination and emergence of trumpet flower (tecoma stans) under different environmental conditions

The aim of this work was to analyze the effect of temperature and light intensity on trumpet flower seed germination, as well as the effect of seeding depth on its emergence. To study the influence of temperature, nine temperature intervals were evaluated, ranging from 15.0 to 40.0 ºC. A randomized block design experiment was used with five replications and 20 seeds per replication, and performed twice. To evaluate light intensity on seed germination, a randomized experimental design was used with eight replications and 25 seeds per replication. The treatments applied were: photoperiod with temperature alternation; photoperiod with constant temperature; darkness with temperature alternation; and darkness with constant temperature. The photoperiod consisted of 8 hours of light and 16 hours of darkness, and the constant temperature was 25 ºC. The treatments with temperature alternations were established with 8 hours at 30 ºC, and 16 hours at 20 ºC. Germination was assessed daily to calculate the total percentage of germination as well as the Germination Velocity Index (GVI). To study the influence of seeding depth on plant emergence, 25 seeds were seeded at 0, 20, 40, and 80 mm in pots with sieved soil. The experiment was arranged in a randomized block design with four replications. Seedling emergence was monitored daily until the 15th day after seeding. After that period, the total percentage of emergence was calculated for each experimental unit, as well as the Emergence Velocity Index (EVI). Formation of normal seedlings and the Germination Velocity Index were different among temperatures and higher germination percentages were observed between 20.3 ºC and 37.5 ºC. Tecoma stans seedlings did not germinate when planted at 40 and 80 mm depth. However, the seedlings placed on the soil surface had an emergence percentage of 72. At 20 mm depth, the emergence rate was 31%.

CARDINAL TEMPERATURES FOR GERMINATION OF THE MEDICINAL ANDDESERT PLANT, Calotropis procera

ABSTRACT Calotropis procera, Apocynaceae, is a wild perennial shrub that originated in the Persian deserts. It is known to provide key resources in degraded ecosystems to about 80 animal species. C. procera is regenerated by seed and produces lots of small seeds that are dispersed by wind; nonetheless, its density is very low. The purpose of this study is to estimate the cardinal temperatures including the base, optimum, and maximum temperatures of Calotropis procera looking at two different ecotypes in the Iranian desert. The germination behavior of C. procera seeds was tested at temperature regimens of 0, 5, 10, 15, 20, 25, 30, 35 and 40oC and was analyzed using linear regression models. The rate of germination increased between base and optimum thermal conditions, and decreased between optimum and maximum thermal conditions. The base, optimum and maximum temperatures for germination of C. procera seeds were estimated at 19.10, 30.75 and 47.80 oC for the Fars and 20.00, 31.82 and 49.69oC for the Zahedan desert, respectively. Temperature and germination were rated to determine the seeding dates of the C. procera. Overall, cardinal temperatures for germination were dependent on local climate characteristics for the range of adaptations in plant growth of the given species.