KINETICS OF MASS LOSS OF ARABICA COFFEE DURING ROASTING PROCESS

ABSTRACT Roasting is one of the most complex coffee processing steps due to simultaneous transfers of heat and mass. During this process, beans lose mass because of fast physical and chemical changes that will set color and flavor of the commercial coffee beverage. Therefore, we aimed at assessing the kinetics of mass loss in commercially roasted coffee beans according to heating throughout the processing. For that, we used samples of 350-g Arabica coffee processed grains with water content of 0.1217 kga kg-1, in addition to a continuous roaster with firing gas. The roaster had initial temperatures of 285, 325, 345 and 380 °C, decreasing during the process up to 255, 285, 305 and 335 °C respectively. Mass loss was calculated by the difference between grain weight before and after roasting. We observed a linear variation directly dependent on roaster temperature. For each temperature during the process was obtained a constant mass loss rate, which was reported by the Arrhenius model with r2 above 0.98. In a roaster in non-isothermal conditions, the required activation energy to start the mass loss in a commercial coffee roasting index was 52.27 kJ mol -1.

Treatment of ununited anconeal process in 8 dogs by osteotomy and dynamic distraction of the proximal part of the ulna

A surgical technique for the treatment of ununited anconeal process in dogs treated by osteotomy and dynamic distraction of the proximal part of the ulna using a linear external skeletal fixator was evaluated. In all cases the osteotomy was distracted 1mm each day after the surgery until desired distraction had been achieved. Eight dogs and 9 joints diagnosed with ununited anconeal process were treated. The success of the procedure was determined by comparing clinical signs of lameness and degree of arthrosis at the time of diagnosis to 6 months after the surgical intervention. Radiographic union occurred in 88.9% of the affected joints between 21 and 42 days after the surgical procedure. Clinically, six elbows were classified as good, two as satisfactory and one as unsatisfactory. Six months after surgery two elbows had no arthrosis, one had Grade 1, two Grade 2 and one Grade 3. It is concluded the combination of ulnar osteotomy and dynamic distraction of the olecranon by a linear external skeletal fixator is a feasible procedure for the treatment of ununited anconeal process in dogs.

A quality and cost approach for welding process selection

The aim of this work was to propose, apply and evaluate a methodical approach to select welding processes in a productive environment based on market requirements of Quality and Costs. A case study was used. The welds were carried out in laboratory, simulating the joint conditions of a manufacturer and using several welding processes: SMAW, GTAW, pulsed GTAW, GMAW with CO2 and Ar based shielding gases and pulsed GMAW. For Quality analysis geometrical aspects of the beads were considered and for Cost analysis, welding parameters and consumable prices. Quantitative indices were proposed and evaluated. After that, evaluation of both Quality and Costs was done, showing to be possible to select the most suitable welding process to a specific application, taking into account the market conditions of a company.

The application of Process Management for reliability enhancement of the Taguchi method

The concept of Process Management has been used by managers and consultants that search for the improvement of both operational or managerial industrial processes. Its strength is in focusing on the external client and on the optimization of the internal process in order to fulfill their needs. By the time the needs of internal clients are being sought, a set of improvements takes place. The Taguchi method, because of its claim for knowledge share between design engineers and people engaged in the process, is a candidate for process management implementation. The objective of this paper is to propose that kind of application aiming for improvements related with reliability of results revealed by the robust design of Taguchi method.

On the Efficiency of Alternatives in Process Plans

Process planning is a very important industrial activity, since it determines how a part or a product is manufactured. Process planning decisions include machine selection, tool selection, and cutting conditions determination, and thus it is a complex activity. In the presence of unstable demand, flexibility has become a very important characteristic of today's successful industries, for which Flexible Manufacturing Systems (FMSs) have been proposed as a solution. However, we believe that FMS control software is not flexible enough to adapt to different manufacturing system conditions aiming at increasing the system's efficiency. One means to overcome this limitation is to include pre-planned alternatives in the process plan; then planning decisions are made by the control system in real time to select the most appropriate alternative according to the conditions of the shop floor. Some of the advantages of this approach reported in the literature are the reduction of the number of tool setups, and the selection of a replacement machine for executing an operation. To verify whether the presence of alternatives in process plans actually increases the efficiency of the manufacturing system, an investigation was carried out using simulation and design of experiments techniques for alternative plans on a single machine. The proposed methodology and the results are discussed within this paper.

Influence of Cutting Conditions on Tool Life, Tool Wear and Surface Finish in the Face Milling Process

The main goal of this work is to study the influence of cutting conditions - cutting speed, feed velocity and feed per tooth - on tool life and surface finish of the workpiece in the face milling of flat surfaces. Aiming to achieve this goal, several milling experiments were carried out with different cutting speeds, feed velocities and feeds per tooth. In the first phase of the experiments, cutting speed was varied without varying feed velocity, which caused a variation in feed per tooth. In the second phase of the experiments, cutting speed and feed velocity were varied in such a way that feed per tooth was kept constant. Tool flank wear and surface roughness of the workpiece were measured as cutting time elapsed. The main conclusions of this work are that a) cutting speed has a strong influence on tool life, regardless of whether feed velocity or feed per tooth varies and b) an increase in surface roughness of the workpiece is not closely related to an increase in wear of the primary cutting edge.

How and why to measure the germination process?

In the last two centuries, papers have been published including measurements of the germination process. High diversity of mathematical expressions has made comparisons between papers and some times the interpretation of results difficult. Thus, in this paper is included a review about measurements of the germination process, with an analysis of the several mathematical expressions included in the specific literature, recovering the history, sense, and limitations of some germination measurements. Among the measurements included in this paper are the germinability, germination time, coefficient of uniformity of germination (CUG), coefficient of variation of the germination time (CVt), germination rate (mean rate, weighted mean rate, coefficient of velocity, germination rate of George, Timson’s index, GV or Czabator’s index; Throneberry and Smith’s method and its adaptations, including Maguire’s rate; ERI or emergence rate index, germination index, and its modifications), uncertainty associated to the distribution of the relative frequency of germination (U), and synchronization index (Z). The limits of the germination measurements were included to make the interpretation and decisions during comparisons easier. Time, rate, homogeneity, and synchrony are aspects that can be measured, informing the dynamics of the germination process. These characteristics are important not only for physiologists and seed technologists, but also for ecologists because it is possible to predict the degree of successful of a species based on the capacity of their harvest seed to spread the germination through time, permitting the recruitment in the environment of some part of the seedlings formed.

Structural basis for the pathophysiology of lipoprotein(a) in the athero-thrombotic process

Lipoprotein Lp(a) is a major and independent genetic risk factor for atherosclerosis and cardiovascular disease. The essential difference between Lp(a) and low density lipoproteins (LDL) is apolipoprotein apo(a), a glycoprotein structurally similar to plasminogen, the precursor of plasmin, the fibrinolytic enzyme. This structural homology endows Lp(a) with the capacity to bind to fibrin and to membrane proteins of endothelial cells and monocytes, and thereby to inhibit plasminogen binding and plasmin generation. The inhibition of plasmin generation and the accumulation of Lp(a) on the surface of fibrin and cell membranes favor fibrin and cholesterol deposition at sites of vascular injury. Moreover, insufficient activation of TGF-ß due to low plasmin activity may result in migration and proliferation of smooth muscle cells into the vascular intima. These mechanisms may constitute the basis of the athero-thrombogenic mode of action of Lp(a). It is currently accepted that this effect of Lp(a) is linked to its concentration in plasma. An inverse relationship between Lp(a) concentration and apo(a) isoform size, which is under genetic control, has been documented. Recently, it has been shown that inhibition of plasminogen binding to fibrin by apo(a) is also inversely associated with isoform size. Specific point mutations may also affect the lysine-binding function of apo(a). These results support the existence of functional heterogeneity in apolipoprotein(a) isoforms and suggest that the predictive value of Lp(a) as a risk factor for vascular occlusive disease would depend on the relative concentration of the isoform with the highest affinity for fibrin

Analysis of viral and cellular parameters which affect the fusion process of influenza viruses

In the present investigation we studied the fusogenic process developed by influenza A, B and C viruses on cell surfaces and different factors associated with virus and cell membrane structures. The biological activity of purified virus strains was evaluated in hemagglutination, sialidase and fusion assays. Hemolysis by influenza A, B and C viruses ranging from 77.4 to 97.2%, from 20.0 to 65.0%, from 0.2 to 93.7% and from 9.0 to 76.1% was observed when human, chicken, rabbit and monkey erythrocytes, respectively, were tested at pH 5.5. At this pH, low hemolysis indexes for influenza A, B and C viruses were observed if horse erythrocytes were used as target cells for the fusion process, which could be explained by an inefficient receptor binding activity of influenza on N-glycolyl sialic acids. Differences in hemagglutinin receptor binding activity due to its specificity to N-acetyl or N-glycolyl cell surface oligosaccharides, density of these cellular receptors and level of negative charges on the cell surface may possibly explain these results, showing influence on the sialidase activity and the fusogenic process. Comparative analysis showed a lack of dependence between the sialidase and fusion activities developed by influenza B viruses. Influenza A viruses at low sialidase titers (<2) also exhibited clearly low hemolysis at pH 5.5 (15.8%), while influenza B viruses with similarly low sialidase titers showed highly variable hemolysis indexes (0.2 to 78.0%). These results support the idea that different virus and cell-associated factors such as those presented above have a significant effect on the multifactorial fusion process

The use of confocal laser scanning microscopy to analyze the process of parasitic protozoon-host cell interaction

In this communication we review the results obtained with the confocal laser scanning microscope to characterize the interaction of epimastigote and trypomastigote forms of Trypanosoma cruzi and tachyzoites of Toxoplasma gondii with host cells. Early events of the interaction process were studied by the simultaneous localization of sites of protein phosphorylation, revealed by immunocytochemistry, and sites of actin assembly, revealed by the use of labeled phaloidin. The results obtained show that proteins localized in the interaction sites are phosphorylated. The process of formation of the parasitophorous vacuole was monitored by labeling the host cell surface with fluorescent probes for lipids (PKH26), proteins (DTAF) and sialic acid (FITC-thiosemicarbazide) before interaction with the parasites. Evidence was obtained indicating transfer of components of the host cell surface to the parasite surface in the beginning of the interaction process. We also analyzed the distribution of cytoskeletal structures (microtubules and microfilaments visualized with specific antibodies), mitochondria (visualized with rhodamine 123), the Golgi complex (visualized with C6-NBD-ceramide) and the endoplasmic reticulum (visualized with anti-reticulin antibodies and DIOC6) during the evolution of intracellular parasitism. The results obtained show that some, but not all, structures change their position during evolution of the intracellular parasitism.

Leukocyte adhesion - a fundamental process in leukocyte physiology

Leukocyte adhesion is of pivotal functional importance. The adhesion involves several different adhesion molecules, the most important of which are the leukocyte ß2-integrins (CD11/CD18), the intercellular adhesion molecules, and the selectins. We and others have extensively studied the specificity and binding sites in the integrins and the intercellular adhesion molecules for their receptors and ligands. The integrins have to become activated to exert their functions but the possible mechanisms of activation remain poorly understood. Importantly, a few novel intercellular adhesion molecules have been recently described, which seem to function only in specific tissues. Furthermore, it is becoming increasingly apparent that changes in integrins and intercellular adhesion molecules are associated with a number of acute and chronic diseases.

A biolistic process for in vitro gene transfer into chicken embryos

Chicken embryos kept in culture medium were bombarded using a high helium gas pressure biolistic device. To optimize the factors that affect transformation efficiency, the lacZ gene under control of the human cytomegalovirus immediate early enhancer/promoter was used as a reporter gene. There was an inverse relationship between survival rate and transformation efficiency. The best conditions obtained for high embryo survival and high transformation efficiency were achieved with 800 psi helium gas pressure, 500 mmHg vacuum, gold particles, an 8 cm DNA-coated microparticle flying distance to the embryo and embryo placement 0.5 cm from the center of the particle dispersion cone. Under these conditions, transformation efficiency was 100%, survival rate 25% and the number of expression units in the embryo body cells ranged from 100 to 1,000. Expression of green fluorescent protein was also detected in embryos bombarded under optimal conditions. Based on the results obtained, the biolistic process can be considered an efficient method for the transformation of chicken embryos and therefore can be used as a model system to study transient gene expression and tissue-specific promoters.

A morphometric study of the lumbar spinous process in the Chinese population

Our goal was to analyze the anatomical parameters of the lumbar spine spinous process for an interspinous stabilization device designed for the Chinese population and to offer an anatomical basis for its clinical application. The posterior lumbar spines (T12-S1) of 52 adult cadavers were used for measuring the following: distance between two adjacent spinous processes (DB), distance across two adjacent spinous processes (DA), thickness of the central spinous processes (TC), thickness of the superior margin of the spinous processes (TS), thickness of the inferior margin of the spinous processes (TI), and height of the spinous processes (H). Variance and correlation analyses were conducted for these data, and the data met the normal distribution and homogeneity of variance. DB decreased gradually from L1-2 to L5-S1. DA increased from T12-L1 to L2-3 and then decreased from L2-3 to L4-5. The largest H in males was noted at L3 (25.45±5.96 mm), whereas for females the largest H was noted at L4 (18.71±4.50 mm). Usually, TS of the adjacent spinous process was lower than TI. Based on the anatomical parameters of the lumbar spinous processes obtained in this study, an “H”-shaped coronal plane (posterior view) was proposed as an interspinous stabilization device for the Chinese population. This study reports morphometric data of the lumbar spinous processes in the Chinese population, which provides an anatomical basis for future clinical applications.

SEPARATION OF SATURED AND UNSATURATED FATTY ACIDS FROM PALM FATTY ACIDS DISTILLATES IN CONTINUOUS MULTISTAGE COUNTERCURRENT COLUMNS WITH SUPERCRITICAL CARBON DIOXIDE AS SOLVENT: A PROCESS DESIGN METHODOLOGY

In this work the separation of multicomponent mixtures in counter-current columns with supercritical carbon dioxide has been investigated using a process design methodology. First the separation task must be defined, then phase equilibria experiments are carried out, and the data obtained are correlated with thermodynamic models or empirical functions. Mutual solubilities, Ki-values, and separation factors aij are determined. Based on this data possible operating conditions for further extraction experiments can be determined. Separation analysis using graphical methods are performed to optimize the process parameters. Hydrodynamic experiments are carried out to determine the flow capacity diagram. Extraction experiments in laboratory scale are planned and carried out in order to determine HETP values, to validate the simulation results, and to provide new materials for additional phase equilibria experiments, needed to determine the dependence of separation factors on concetration. Numerical simulation of the separation process and auxiliary systems is carried out to optimize the number of stages, solvent-to-feed ratio, product purity, yield, and energy consumption. Scale-up and cost analysis close the process design. The separation of palmitic acid and (oleic+linoleic) acids from PFAD-Palm Fatty Acids Distillates was used as a case study.

Influence of carbon source and the fermentation process on levan production by Zymomonas mobilis analyzed by the surface response method

The aim of this study is to assess sugar cane juice and sucrose as substrates, the batch and fed batch processes and their interaction in the levan production using a complete factorial design. Zymomonas mobilis was cultivated in different sugar cane juice and sucrose concentrations in two fermentation processes at 25 °C for 20 h. A complete factorial design (2³) was used to analyze the effects of the type and concentration of the substrate, as well as the batch and fed batch processes. A complete second factorial design (2²) was used to observe the importance of sugar cane juice. The results indicated that the batch process improved the levan production reaching 40.14 g/L. The addition of sugar cane juice was not statistically significant for levan formation, however sugar cane juice stimulated biomass, sorbitol and ethanol production. The best medium for levan production was 150 g/L sucrose in batch.