Optimization and validation of the solid-liquid extraction technique for determination of picloram in soils by high performance liquid chromatography

The objective of this study was to optimize and validate the solid-liquid extraction (ESL) technique for determination of picloram residues in soil samples. At the optimization stage, the optimal conditions for extraction of soil samples were determined using univariate analysis. Ratio soil/solution extraction, type and time of agitation, ionic strength and pH of extraction solution were evaluated. Based on the optimized parameters, the following method of extraction and analysis of picloram was developed: weigh 2.00 g of soil dried and sieved through a sieve mesh of 2.0 mm pore, add 20.0 mL of KCl concentration of 0.5 mol L-1, shake the bottle in the vortex for 10 seconds to form suspension and adjust to pH 7.00, with alkaline KOH 0.1 mol L-1. Homogenate the system in a shaker system for 60 minutes and then let it stand for 10 minutes. The bottles are centrifuged for 10 minutes at 3,500 rpm. After the settlement of the soil particles and cleaning of the supernatant extract, an aliquot is withdrawn and analyzed by high performance liquid chromatography. The optimized method was validated by determining the selectivity, linearity, detection and quantification limits, precision and accuracy. The ESL methodology was efficient for analysis of residues of the pesticides studied, with percentages of recovery above 90%. The limits of detection and quantification were 20.0 and 66.0 mg kg-1 soil for the PVA, and 40.0 and 132.0 mg kg-1 soil for the VLA. The coefficients of variation (CV) were equal to 2.32 and 2.69 for PVA and TH soils, respectively. The methodology resulted in low organic solvent consumption and cleaner extracts, as well as no purification steps for chromatographic analysis were required. The parameters evaluated in the validation process indicated that the ESL methodology is efficient for the extraction of picloram residues in soils, with low limits of detection and quantification.

Photosynthetic characteristics of hybrid and conventional rice plants as a function of plant competition

The objective of this work was to evaluate the characteristics related to the photosynthetic ability of hybrid and inbred rice varieties, as a way to assess which of the two presented higher potential to stand out under conditions of competition. The trial was set in a greenhouse in completely randomized block design and 2 x 6 factorial scheme with four replications. Factor A consisted of rice varieties (hybrid or inbred) and factor B by competition levels. Treatments consisted in maintaining one plant of either BRS Pelota (inbred) or Inov (hybrid) variety at the center of the plot, under competition with 0, 1, 2, 3, 4 or 5 plants of the variety BRS Pelota at the periphery of the experimental unit, according to the treatment. Fifty days after emergence (DAE), sub-stomatal CO2 concentration (Ci - mmol mol-1), photosynthetic rate (A - mmol m-2 s-1) and CO2 consumed (DC - mmol mol-1) were quantified, as well as shoot dry mass(SDM).Hybrid plants present higher photosynthesis capacity than inbred plants, when competing with up to 3 times its own density. When under the same competitive intensity, hybrid plants surpass the inbred. However, it should be emphasized that, when in farm condition, the lower competitive capacity with weeds often attributed to the hybrid varieties, probably is due to their lower planting density, but if weed competition is kept at low levels, hybrid rice plants may perform in the same way or usually better than inbred plants.

Influence of seed size and ecological factors on the germination and emergence of field bindweed (Convolvulus arvensis)

An understanding of seed germination ecology of weeds can assist in predicting their potential distribution and developing effective management strategies. Influence of environmental factors and seed size on germination and seedling emergence of Convolvulus arvensis (field bindweed) was studied in laboratory and greenhouse conditions. Germination occurred over a wide range of constant temperatures, between 15 and 40 ºC, with optimum germination between 20 and 25 ºC. Time to start germination, time to 50% germination and mean germination time increased while germination percentage and germination index decreased with an increase in temperature from 20 ºC, salinity and osmotic stress. However, germination was tolerant to low salt (25 mM) or osmotic stress (0.2 MPa), but as salinity and osmotic stress increased, germination percentage and germination index decreased. Seeds of C. arvensis placed at soil surface showed maximum emergence and decreased as seeding depth increased. Seeds of C. arvensis germinated over a wide range of pH (4 to 9) but optimum germination occurred at pH 6 to 8. Under highly alkaline and acidic pH, time to start germination, time to 50% germination and mean germination time increased while germination percentage and germination index decreased. Increase in field capacity caused decreased time to start germination, time to 50% germination and mean germination time but increased germination percentage and germination index. Bigger seeds had low time to start germination, time to 50% germination and mean germination time but high germination percentage and germination index. Smaller seeds were more sensitive to environmental factors as compared to larger or medium seeds. It can be concluded that except for pH, all environmental factors and seed sizes adversely affect C. arvensis as regards seed germination or emergence and germination or emergence traits, and larger seeds result in improved stand establishment and faster germination than small seeds, regardless of moisture stress or deeper seeding depth.

Use of herbicides on turfgrass

In crop production, weeds must be controlled so as not to adversely affect crop yield and crop quality. Thus, a low level of weeds infesting a field, in most instances, is not a problem. Except in sod or seed production, turfgrass does not have a yield component. The value of turfgrass is its inherent aesthetic quality and usability. Aesthetic quality is the beauty and value that turfgrass adds to a managed landscape. Usability can be the durability of a sport field, trueness of golf putting green roll, or reduction in soil loss from water runoff or wind. Any weed presence in turfgrass can decrease the aesthetic quality and usability of turfgrass. Utilizing herbicides is the only way to completely control weeds in a turfgrass stand. While it is possible to reduce weed populations using cultural or mechanical management practices, it is impossible to completely eliminate weeds as can be accomplished with herbicides. This manuscript will review the major herbicides used in turfgrass in the United States with respect to their modes of action, herbicide family, and primary use in turfgrass.

GLYPHOSATE DRIFT IN EUCALYPTUS PLANTS

ABSTRACTWith the present study we aim to assess the damage caused to Eucalyptus plants exposed to glyphosate drift in different canopy portions. The drift simulation was carried out through application of 1,080 g ha-1 of glyphosate in five canopy portions (0, 25, 50, 75 and 100% of the low branches), in four areas of cultivation. Areas I and II, plants with 0.91 and 2.98 m, and height of canopy drift exposition of 0.30 and 1.0 m, respectively. In areas III and IV both cultivations were 8.15 m high, varying the height of drift exposition between 2.0 and 2.5 m, respectively. At 30 and 480 days after application (DAA), the survival rate was assessed, and at 300 and 480 DAA diameter at breast height (DBH), height, volume and their respective increment were determined. The medium annual increment (MAI) was determined at 480 DAA. Area I, in which the plants were 0.91 m high, we observed that treatment with 100% of the low branches exposed to drift led to stand reduction of the plants around 18.75 and 38.19% at 30 and 480 DAA, respectively. Areas I and II showed reduction in plant growth in height and DBH, wood volume and MAI, to the extent that there was an increase in the portion of canopy exposed to glyphosate drift. However, in areas III and IV, in which 8.15 m height plants were found, no changes were verified for the evaluated characteristics, regardless of the portion of canopy exposed to glyphosate drift.

SELECTIVITY OF FOMESAFEN TO COTTON

ABSTRACT The aim of this work was to evaluate the selectivity of fomesafen alone or in a tank mixture with other preemergent herbicides, with or without S-metolachlor application in early postemergence in cotton plant, cultivar DP 555 BG RR(r). The design utilized was a randomized complete block, organized in a split-plot arrangement, with four replications. For that, 24 herbicides were evaluated with fomesafen (0.45 and 0.625 kg ha-1), prometryn (1.25 kg ha-1), diuron (1.25 kg ha-1), trifluralin (1.8 kg ha-1), and S-metolachlor (0.77 kg ha-1), applied as preemergent, with or without S-metolachlor (0.77 kg ha-1) applied in early postemergence. The variables evaluated were: phytotoxicity, insertion height of the first reproductive branch, plant height, stand, number of reproductive branches per plant, number of bolls per plant, bolls weight, and productivity of cotton seed. Fomesafen alone or in a tank mixture with preemergent prometryn, diuron, trifluralin and S-metolachlor was selective to cotton plant. Preemergent fomesafen isolated application followed by the application of S-metolachlor in early postemergence was also selective. However, on average, preemergent tank mixtures applied in association with preemergent S-metolachlor early application was not selective to cotton crop.

Diversity and structure of the tree community of a fragment of tropical secondary forest of the brazilian Atlantic Forest domain 15 and 40 years after logging

Two adjacent tracts of tropical secondary forest, situated in Itambé do Mato Dentro, south-eastern Brazil, which had been regenerating for 15 and 40 years after clearing, were compared with the purpose of detecting differences in species diversity and composition, species guild composition (regeneration, stratification and dispersion), and stand structure. Four and three 1,125 m² plots laid on the 15- and 40-year-old stands, respectively, sampled 2,430 trees with diameter at the base of the stem > 5 cm. The number of species (S = 199) was high for this forest type and significantly higher for the older stand. Tree density was significantly higher in the younger stand, particularly for smaller trees, whereas the two stands did not differ in both basal area and volume per hectare. Trees of shade-tolerant and understory species were significantly more abundant in the older stand. Though sharing a large proportion of species (49%), the two stands differed significantly in the abundance of many species. Live stumps probably contributed to the relatively quick restoration of some forest characteristics, particularly species diversity, basal area and volume.

Horizontal and vertical tree community structure in a lowland atlantic rain forest, southeastern Brazil

The horizontal and vertical tree community structure in a lowland Atlantic Rain Forest was investigated through a phytosociological survey in two 0.99 ha plots in the Intervales State Park, São Paulo State. All trees > 5 cm diameter at breast height were recorded. 3,078 individuals belonging to 172 species were identified and recorded. The Shannon diversity index was H' = 3.85 nat.ind.-1. The Myrtaceae family showed the greatest floristic richness (38 species) and the highest density (745 individuals) in the stand. Euterpe edulis Mart. had the highest importance value (33.98%) accounting for 21.8% of all individuals recorded. The quantitative similarity index was higher than the qualitative index, showing little structural variation between plots. However, the large number of uncommon species resulted in pronounced floristic differences. A detrended correspondence analysis (DCA) generated three arbitrary vertical strata. Stratum A (> 26 m), where Sloanea guianensis (Aubl.) Benth. and Virola bicuhyba (Schott. ex A.DC.) Warb. were predominant showed the lowest density. Stratum B (8 m < h < 26 m) had the greatest richness and diversity, and stratum C (< 8 m) showed the highest density. Euterpe edulis, Guapira opposita (Vell.) Reitz, Garcinia gardneriana (Planch. & Triana) Zappi, and Eugenia mosenii (Kausel) Sobral were abundant in strata B and C. The occurrence of strata in tropical forests is discussed and we recommend the use of DCA for others studies of the vertical distribution of tropical forest tree communities.

An overview of lignin metabolism and its effect on biomass recalcitrance

Lignin, after cellulose, is the second most abundant biopolymer on Earth, accounting for 30% of the organic carbon in the biosphere. It is considered an important evolutionary adaptation of plants during their transition from the aquatic environment to land, since it bestowed the early tracheophytes with physical support to stand upright and enabled long-distance transport of water and solutes by waterproofing the vascular tissue. Although essential for plant growth and development, lignin is the major plant cell wall component responsible for biomass recalcitrance to industrial processing. The fact that lignin is a non-linear aromatic polymer built with chemically diverse and poorly reactive linkages and a variety of monomer units precludes the ability of any single enzyme to properly recognize and degrade it. Consequently, the use of lignocellulosic feedstock as a renewable and sustainable resource for the production of biofuels and bio-based materials will depend on the identification and characterization of the factors that determine plant biomass recalcitrance, especially the highly complex phenolic polymer lignin. Here, we summarize the current knowledge regarding lignin metabolism in plants, its effect on biomass recalcitrance and the emergent strategies to modify biomass recalcitrance through metabolic engineering of the lignin pathway. In addition, the potential use of sugarcane as a second-generation biofuel crop and the advances in lignin-related studies in sugarcane are discussed.

Spectral analysis of the electromyograph of the erector spinae muscle before and after a dynamic manual load-lifting test

The aim of the present study was to assess the spectral behavior of the erector spinae muscle during isometric contractions performed before and after a dynamic manual load-lifting test carried out by the trunk in order to determine the capacity of muscle to perform this task. Nine healthy female students participated in the experiment. Their average age, height, and body mass (± SD) were 20 ± 1 years, 1.6 ± 0.03 m, and 53 ± 4 kg, respectively. The development of muscle fatigue was assessed by spectral analysis (median frequency) and root mean square with time. The test consisted of repeated bending movements from the trunk, starting from a 45º angle of flexion, with the application of approximately 15, 25 and 50% of maximum individual load, to the stand up position. The protocol used proved to be more reliable with loads exceeding 50% of the maximum for the identification of muscle fatigue by electromyography as a function of time. Most of the volunteers showed an increase in root mean square versus time on both the right (N = 7) and the left (N = 6) side, indicating a tendency to become fatigued. With respect to the changes in median frequency of the electromyographic signal, the loads used in this study had no significant effect on either the right or the left side of the erector spinae muscle at this frequency, suggesting that a higher amount and percentage of loads would produce more substantial results in the study of isotonic contractions.

Muscular function and functional mobility of faller and non-faller elderly women with osteoarthritis of the knee

Falls are a major concern in the elderly population with chronic joint disease. To compare muscular function and functional mobility among older women with knee osteoarthritis with and without a history of falls, 15 elderly women with a history of falls (74.20 ± 4.46 years) and 15 without a history of falls (71.73 ± 4.73 years) were studied. Muscular function, at the angular speed of 60, 120, and 180º/s, was evaluated using the Biodex Isokinetic Dynamometer. The sit-to-stand task was performed using the Balance Master System and the Timed Up and Go test was used to determine functional mobility. After collection of these data, the history of falls was investigated. A statistically significant difference was detected in the time taken to transfer the center of gravity during the sit-to-stand test (means ± SD; non-fallers: 0.35 ± 0.16 s; fallers: 0.55 ± 0.32 s; P = 0.049, Student t-test) and in the Timed Up and Go test (medians; non-fallers: 10.08 s; fallers: 11.59 s; P = 0.038, Mann-Whitney U-test). The results indicated that elderly osteoarthritic women with a history of falls presented altered functional mobility and needed more time to transfer the center of gravity in the sit-to-stand test. It is important to implement strategies to guarantee a better functional performance of elderly patients to reduce fall risks.

Comparison of scientists of the Brazilian Academy of Sciences and of the National Academy of Sciences of the USA on the basis of the h-index

A new scientometric indicator, the h-index, has been recently proposed (Hirsch JE. Proc Natl Acad Sci 2005; 102: 16569-16572). The index avoids some shortcomings of the calculation of the total number of citations as a parameter to evaluate scientific performance. Although it has become known only recently, it has had widespread acceptance. A comparison of the average h-index of members of the Brazilian Academy of Sciences (BAS) and of the National Academy of Sciences of the USA (NAS-USA) was carried out for 10 different areas of science. Although, as expected, the comparison was unfavorable to the members of the BAS, the imbalance was distinct in different areas. Since these two academies represent, to a significant extent, the science of top quality produced in each country, the comparison allows the identification of the areas in Brazil that are closer to the international stakeholders of scientific excellence. The areas of Physics and Mathematics stand out in this context. The heterogeneity of the h-index in the different areas, estimated by the median dispersion of the index, is significantly higher in the BAS than in the NAS-USA. No elements have been collected in the present study to provide an explanation for this fact.

A forced running wheel system with a microcontroller that provides high-intensity exercise training in an animal ischemic stroke model

We developed a forced non-electric-shock running wheel (FNESRW) system that provides rats with high-intensity exercise training using automatic exercise training patterns that are controlled by a microcontroller. The proposed system successfully makes a breakthrough in the traditional motorized running wheel to allow rats to perform high-intensity training and to enable comparisons with the treadmill at the same exercise intensity without any electric shock. A polyvinyl chloride runway with a rough rubber surface was coated on the periphery of the wheel so as to permit automatic acceleration training, and which allowed the rats to run consistently at high speeds (30 m/min for 1 h). An animal ischemic stroke model was used to validate the proposed system. FNESRW, treadmill, control, and sham groups were studied. The FNESRW and treadmill groups underwent 3 weeks of endurance running training. After 3 weeks, the experiments of middle cerebral artery occlusion, the modified neurological severity score (mNSS), an inclined plane test, and triphenyltetrazolium chloride were performed to evaluate the effectiveness of the proposed platform. The proposed platform showed that enhancement of motor function, mNSS, and infarct volumes was significantly stronger in the FNESRW group than the control group (P<0.05) and similar to the treadmill group. The experimental data demonstrated that the proposed platform can be applied to test the benefit of exercise-preconditioning-induced neuroprotection using the animal stroke model. Additional advantages of the FNESRW system include stand-alone capability, independence of subjective human adjustment, and ease of use.

Implantation of muscle satellite cells overexpressing myogenin improves denervated muscle atrophy in rats

This study evaluated the effect of muscle satellite cells (MSCs) overexpressing myogenin (MyoG) on denervated muscle atrophy. Rat MSCs were isolated and transfected with the MyoG-EGFP plasmid vector GV143. MyoG-transfected MSCs (MTMs) were transplanted into rat gastrocnemius muscles at 1 week after surgical denervation. Controls included injections of untransfected MSCs or the vehicle only. Muscles were harvested and analyzed at 2, 4, and 24 weeks post-transplantation. Immunofluorescence confirmed MyoG overexpression in MTMs. The muscle wet weight ratio was significantly reduced at 2 weeks after MTM injection (67.17±6.79) compared with muscles injected with MSCs (58.83±5.31) or the vehicle (53.00±7.67; t=2.37, P=0.04 and t=3.39, P=0.007, respectively). The muscle fiber cross-sectional area was also larger at 2 weeks after MTM injection (2.63×103±0.39×103) compared with MSC injection (1.99×103±0.58×103) or the vehicle only (1.57×103±0.47×103; t=2.24, P=0.049 and t=4.22, P=0.002, respectively). At 4 and 24 weeks post-injection, the muscle mass and fiber cross-sectional area were similar across all three experimental groups. Immunohistochemistry showed that the MTM group had larger MyoG-positive fibers. The MTM group (3.18±1.13) also had higher expression of MyoG mRNA than other groups (1.41±0.65 and 1.03±0.19) at 2 weeks after injection (t=2.72, P=0.04). Transplanted MTMs delayed short-term atrophy of denervated muscles. This approach can be optimized as a novel stand-alone therapy or as a bridge to surgical re-innervation of damaged muscles.

Stability of cassava flour-based food bars

The consumption of Brazilian cassava has been reduced due to a lack of adjustment to the modern lifestyle. To reverse this trend, new products could be developed specifically targeted to high-value niche markets. Cereal bars stand out as fast food high in nutritional value. A bar formula mimicking cereal bars was prepared using a mixture of Brazilian cassava flour, hydrogenated vegetable fat, dried bananas, ground cashew nuts, and glucose syrup. After being pressed, the bars were dried for 1 hour at 65 °C, packaged in films, and stored under ambient conditions. Its stability was continuously monitored for 210 days in order to ensure its safety and enable its introduction to the market. Texture loss was observed in the packed bars after 90 days of storage, but the sensory characteristics allowed the testers to perceive this tendency after only 30 days of storage. However, chemical, physical, and microbial analyses confirmed that the bars were safe for consumption for 180 days. The results showed that a 45 g cassava flour-based bar enriched with nuts and dried fruits can meet 6% of the recommended daily fiber intake with a caloric value between that of the common cereal bar and that of an energy bar. Adapting the formula with ingredients (fruits, nuts) from different regions of Brazil may add value to this traditional product as a fast food.