Effects of traffic control on the soil physical quality and the cultivation of sugarcane

The cultivation of sugarcane with intensive use of machinery, especially for harvest, induces soil compaction, affecting the crop development. The control of agricultural traffic is an alternative of management in the sector, with a view to preserve the soil physical quality, resulting in increased sugarcane root growth, productivity and technological quality. The objective of this study was to evaluate the physical quality of an Oxisol with and without control traffic and the resulting effects on sugarcane root development, productivity and technological quality. The following managements were tested: no traffic control (NTC), traffic control consisting of an adjustment of the track width of the tractor and sugarcane trailer (TC1) and traffic control consisting of an adjustment of the track width of the tractor and trailer and use of an autopilot (TC2). Soil samples were collected (layers 0.00-0.10; 0.10-0.20 and 0.20-0.30 m) in the plant rows, inter-row center and seedbed region, 0.30 m away from the plant row. The productivity was measured with a specific weighing scale. The technological variables of sugarcane were measured in each plot. Soil cores were collected to analyze the root system. In TC2, the soil bulk density and compaction degree were lowest and total porosity and macroporosity highest in the plant row. Soil penetration resistance in the plant row, was less than 2 MPa in TC1 and TC2. Soil aggregation and total organic carbon did not differ between the management systems. The root surface and volume were increased in TC1 and TC2, with higher productivity and sugar yield than under NTC. The sugarcane variables did not differ between the managements. The soil physical quality in the plant row was preserved under management TC1 and TC2, with an improved root development and increases of 18.72 and 20.29 % in productivity and sugar yield, respectively.

Analysis of experiments in square lattice with emphasis on variance components. i. Individual analysis

This paper focused on four alternatives of analysis of experiments in square lattice as far as the estimation of variance components and some genetic parameters are concerned: 1) intra-block analysis with adjusted treatment and blocks within unadjusted repetitions; 2) lattice analysis as complete randomized blocks; 3) intrablock analysis with unadjusted treatment and blocks within adjusted repetitions; 4) lattice analysis as complete randomized blocks, by utilizing the adjusted means of treatments, obtained from the analysis with recovery of interblock information, having as mean square of the error the mean effective variance of this same analysis with recovery of inter-block information. For the four alternatives of analysis, the estimators and estimates were obtained for the variance components and heritability coefficients. The classification of material was also studied. The present study suggests that for each experiment and depending of the objectives of the analysis, one should observe which alternative of analysis is preferable, mainly in cases where a negative estimate is obtained for the variance component due to effects of blocks within adjusted repetitions.

Physiological and anatomical characteristics of leaves of two clones of guarana

The objective of this work was to analyze gas exchange, photosynthetic characteristics, photochemical efficiency of photosystem II and anatomical characteristics of young plant leaves of two guarana (Paullinia cupana) clones (BRS-CG372RC and BRS-CG611RL) growing under open field. The variables of gas exchange and fluorescence of chlorophyll a were evaluated in mature leaves. The values of photosynthesis and transpiration found for BRS-CG372RC were 27% greater and 80% lesser than values found for BRS-CG611RL, respectively. The values of stomatal conductance found for the clones BRS-CG372RC and BRS-CG611RL were in the order of 224 and 614 mmol mm-2 s-1, respectively. The values of photorespiration, rate of carboxylation and rate electron transport were greater in BRS-CG372RC. The clone BRS-CG372RC exhibited stomatal density 26% greater than BRS-CG611RL. However, the area of ostiolar opening was 42% greater in BRS-CG611RL. The values of the water use efficiency in BRS-CG372RC were 134% greater than in BRS-CG611RL. High stomatal density and low stomatal conductance can be important characteristics in the selection of the clones with a good ability to assimilate carbon and optimize the use of water.

Breeding strategies for recurrent selection of maize

The objectives of this work were to analyze theoretical genetic gains of maize due to recurrent selection among full-sib and half-sib families, obtained by Design I, Full-Sib Design and Half-Sib Design, and genotypic variability and gene loss with long term selection. The designs were evaluated by simulation, based on average estimated gains after ten selection cycles. The simulation process was based on seven gene systems with ten genes (with distinct degrees of dominance), three population classes (with different gene frequencies), under three environmental conditions (heritability values), and four selection strategies. Each combination was repeated ten times, amounting to 25, 200 simulations. Full-sib selection is generally more efficient than half-sib selection, mainly with favorable dominant genes. The use of full-sib families derived by Design I is generally more efficient than using progenies obtained by Full-Sib Design. Using Design I with 50 males and 200 females (effective size of 160) did not result in improved populations with minimum genotypic variability. In the populations with lower effective size (160 and 400) the loss of favorable genes was restricted to recessive genes with reduced frequencies.

Genetic diversity of Brazilian triticales evaluated with genomic wheat microsatellites

The objective of this work was to determine the genetic variability available for triticale (X Triticosecale Wittmack) crop improvement in Brazil. Forty-two wheat genomic microsatellites were used to estimate the molecular diversity of 54 genotypes, which constitute the base of one of the major triticale breeding programs in the country. Average heterozygosity was 0.06 and average and effective number of alleles per locus were 2.13 and 1.61, respectively, with average allelic frequency of 0.34. The set of genomic wheat microsatellites used clustered the genotypes into seven groups, even when the germplasm was originated primarily from only two triticale breeding programs, a fact reflected on the average polymorphic information content value estimated for the germplasm (0.36). The 71.42% transferability achieved for the tested microsatellites indicates the possibility of exploiting these transferable markers in further triticale genetic and breeding studies, even those mapped on the D genome of wheat, when analyzing hexaploid triticales.

Genetic improvement and population structure of the Nelore breed in Northern Brazil

The objective of this work was to evaluate the population structure and the genetic and phenotypic progress of Nelore cattle in Northern Brazil. Pedigree information concerning animals born between 1942 and 2006 were analyzed. Population structure was performed using the Endog program. Out of the 140,628 animals studied, 67.7, 14.52 and 3.18% had complete pedigree record of the first, second and third parental generation, respectively. Inbreeding and average relatedness coefficients were low: 0.2 and 0.13%, respectively. However, these parameters may have been underestimated, since information on pedigree was incomplete. The effective number of founders was 370 and the genetic contribution of 10, 50 and 448 most influent ancestors explained 13.2, 28 and 50% of the genetic variability in the population, respectively. The genetic variability for growth traits and population structure demonstrates high probability of increasing productivity through selective breeding. Moreover, management strategies to reduce the currently observed age at first calving and generation intervals are important for Nelore cattle genetic improvement.

Mating system parameters in a high density population of andirobas in the Amazon forest

The objective of this work was to estimate the mating system parameters of a andiroba (Carapa guianensis) population using microsatellite markers and the mixed and correlated mating models. Twelve open‑pollinated progeny arrays of 15 individuals were sampled in an area with C. guianensis estimated density of 25.7 trees per hectare. Overall, the species has a mixed reproductive system, with a predominance of outcrossing. The multilocus outcrossing rate (t m = 0.862) was significantly lower than the unity, indicating that self‑pollination occurred. The rate of biparental inbreeding was substantial (t m ‑ t s = 0.134) and significantly different from zero. The correlation of selfing within progenies was high (r s = 0.635), indicating variation in the individual outcrossing rate. Consistent with this result, the estimate of the individual outcrossing rate ranged from 0.598 to 0.978. The multilocus correlation of paternity was low (r p(m) = 0.081), but significantly different from zero, suggesting that the progenies contain full‑sibs. The coancestry within progenies (Θ = 0.185) was higher and the variance effective size (Ne(v) = 2.7) was lower than expected for true half‑sib progenies (Θ = 0.125; Ne(v) = 4). These results suggest that, in order to maintain a minimum effective size of 150 individuals for breeding, genetic conservation, and environmental reforestation programs, seeds from at least 56 trees must be collected.

LOW COST ANALYZER FOR THE DETERMINATION OF PHOSPHORUS BASED ON OPEN-SOURCE HARDWARE AND PULSED FLOWS

The need for automated analyzers for industrial and environmental samples has triggered the research for new and cost-effective strategies of automation and control of analytical systems. The widespread availability of open-source hardware together with novel analytical methods based on pulsed flows have opened the possibility of implementing standalone automated analytical systems at low cost. Among the areas that can benefit from this approach are the analysis of industrial products and effluents and environmental analysis. In this work, a multi-pumping flow system is proposed for the determination of phosphorus in effluents and polluted water samples. The system employs photometric detection based on the formation of molybdovanadophosphoric acid, and the fluidic circuit is built using three solenoid micropumps. The detection is implemented with a low cost LED-photodiode photometric detection system and the whole system is controlled by an open-source Arduino Uno microcontroller board. The optimization of the timing to ensure the color development and the pumping cycle is discussed for the proposed implementation. Experimental results to evaluate the system behavior are presented verifying a linear relationship between the relative absorbance and the phosphorus concentrations for levels as high as 50 mg L-1.

Description of epidemics of coffee rust with neural networks

The objective of this paper was to evaluate the potential of neural networks (NN) as an alternative method to the basic epidemiological approach to describe epidemics of coffee rust. The NN was developed from the intensities of coffee (Coffea arabica) rust along with the climatic variables collected in Lavras-MG between 13 February 1998 and 20 April 2001. The NN was built with climatic variables that were either selected in a stepwise regression analysis or by the Braincel® system, software for NN building. Fifty-nine networks and 26 regression models were tested. The best models were selected based on small values of the mean square deviation (MSD) and of the mean prediction error (MPE). For the regression models, the highest coefficients of determination (R²) were used. The best model developed with neural networks had an MSD of 4.36 and an MPE of 2.43%. This model used the variables of minimum temperature, production, relative humidity of the air, and irradiance 30 days before the evaluation of disease. The best regression model was developed from 29 selected climatic variables in the network. The summary statistics for this model were: MPE=6.58%, MSE=4.36, and R²=0.80. The elaborated neural networks from a time series also were evaluated to describe the epidemic. The incidence of coffee rust at four previous fortnights resulted in a model with MPE=4.72% and an MSD=3.95.

A study on the inhibition of mild steel corrosion in hydrochloric acid by pyridoxol hydrochloride

The inhibition of the corrosion of mild steel in 2M hydrochloric acid solutions by Pyridoxol hydrochloride (PXO) has been studied using weight loss and hydrogen evolution techniques. The inhibitor (PXO) exhibited highest inhibition efficiency of 71.93% at the highest inhibitor concentration of 1.0 x 10-2M investigated and a temperature of 303K from weight loss result. Also, inhibition was found to increase with increasing concentration of the inhibitor and decreasing temperature. A first order type of mechanism has been deduced from the kinetic treatment of the weight loss results and the process of inhibition attributed to physical adsorption. The results obtained from the two techniques show that pyridoxol hydrochloride could serve as an effective inhibitor of the corrosion of mild steel in HCl acid solution. The compound obeys the Langmuir adsorption isotherm equation.

METHODOLOGY FOR AUTOMATICALLY DELIMITING PERMANENT PRESERVATION AREAS ALONG WATER COURSES - THE USE OF GIS IN THE HYDROLOGICAL BASIN OF THE SERGIPE RIVER, BRAZIL

ABSTRACT Permanent Preservation Areas (PPAs) along watercourses have been the focus of numerous studies, not only because of the fragility and ecological relevance of riverine vegetation, but also because of the inefficiency demonstrated in conforming to the legislation protecting it. One of the major difficulties encountered in terms of guaranteeing the effective conservation of these riverside areas is the absence of methodologies that can be used to define them rapidly and accurately without manually determining the widths of the rivers or assigning only uniform linear values for the entire watercourse. The present work sought to develop a spatial analysis methodology capable of automatically defining permanent preservation areas along watercourses using geographic information system (GIS) software. The present study was undertaken in the Sergipe River basin, "considering the river itself and its principal affluents. We used the database of the Digital Atlas of Hydrological Resources (SEMARH/SE), and the delimitations of the PPAs were performed using ArcGIS 10.1 and the XToolPro 9.0 extension. A total of 5,003.82 hectares of Permanent Preservation Areas were delimited along the margins of the rivers analyzed, with a margin of error of <1% in delimiting the widths of the rivers within the entire area considered. The methodology described here can be used to define PPAs efficiently, relatively rapidly, and with very small margins of error, thus representing a technological advance in terms of using GIS for land management.

NON-DESTRUCTIVE ANALYSIS OF THE ROOT SYSTEM AND TREE GROWTH PARAMETERS

ABSTRACT The productivity of Eucalyptus at plantations is increasing and has undergone a variety of research studies. Most research is dealing with simple dendrometric variables like the DBH (diameter at breast height) and tree height, or more complex variables including crown parameters or variables concerning photosynthesis. The root systems, however, have not been well analyzed yet. The objective of the study was to analyze the root system with a non-destructive method and to evaluate possible correlations with dendrometric variables of the tree (DBH, height, crown expansion). A small experimental plantation with 39 even-aged, 6-year-old trees of Eucalyptus grandis x urophylla has been investigated within this study. The results of the study show the highest correlation of the root areas with the crown expansion. In general, the root area shows a significantly bigger expansion in the eucalypt plantation than the tree crown, with a more homogeneous development.

Numerical evaluation of the modulus of longitudinal elasticity in structural round timber elements of the Eucalyptus genus

Currently, the standards that deal with the determination of the properties of rigidity and strength for structural round timber elements do not take in consideration in their calculations and mathematical models the influence of the existing irregularities in the geometry of these elements. This study has as objective to determine the effective value of the modulus of longitudinal elasticity for structural round timber pieces of the Eucalyptus citriodora genus by a technique of optimization allied to the Inverse Analysis Method, to the Finite Element Method and the Least Square Method.

Root system distribution of sugarcane irrigated with domestic sewage effluent aplication by subsurface drip system

Irrigation with domestic sewage effluent (DSE) has been recommended by subsurface dripping, as it can obtain a high rate of irrigation efficiency and faster use of salts in comparison with other irrigation methods. The study aimed at evaluating the area, the length and the effective depth of the root system of sugarcane irrigated with DSE by subsurface drip system and with different irrigation rates at depths of 0.00-0.20, 0.20-0.40, 0.40-0.60 and 0.60-0.80m. The experiment was carried out in the municipality of Piracicaba, in the state of São Paulo (SP), Brazil, in a sugarcane area irrigated with DSE in a completely randomized blocks set up in furrows, with three replications and four treatments, which are: one area without irrigation (AWI) and three irrigated areas meeting 50% (T50%), 100% (T100%) and 200% (T200%) of the crop's water need between each round of irrigation. T100% and T200% provided smaller areas and lengths of roots in the two deepest layers, as compared to AWI and T50%, which stimulated the development of deeper roots due to the water stress. TWI, T100% and T200% presented 80% of the roots up to a depth of 0.40m and T50% treatment presented 76.43% of roots total.

Economic analysis for sizing of sugarcane (Saccharum spp.) mechanized harvesting

Sugarcane has a significant role on Brazilian agribusiness economy. The harvesting cane is considered as one of the most important operations of the process for it has to attend the raw material demanded by the sugar mill in quality and a competitive cost. The objective of this work it is it of analyzing, of systemic way, the variables influence on economical and operational performance in sugarcane mechanized harvesting process for sizing of machines. For this purpose a model called "ColheCana", was developed in a spreadsheet and in a programming language. The results showed that the field efficiency and harvester´s initial value are variables of great impact in the cost and that there is a maximum area that one equipment can attend and for this area the cost is minimum.