Drying of sicilian lemon residue: influence of process variables on the evaluation of the dietary fiber produced

In this study, the effect of the process variables of the air-drying of Sicilian lemon residues on some technological properties of the fibers produced was studied. The determination and modeling of desorption isotherms were used to establish the equilibrium moisture content at 60, 75, and 90 °C using the static method with 8 saturated salt solutions. The best fit was obtained with BET and GAB models. The drying process was conducted in a vertical tray dryer and delineated according to a central composite experimental design (2²) using the following as factors: air velocity (0.5, 0.75 and 1 m/s) and temperature (60, 75, and 90 °C), and it presented a good fit to the exponential model (R² > 99.9%). The experimental design responses evaluated were the technological properties of the fibers: water-holding, oil-holding, and swelling capacity. Since these properties were present in high levels, the lemon residues could be used to increase content of fibers in foods resulting in the addition of nutritional benefits for the consumers.

Evaluation of the in vitro glycemic index of a fiber-rich extruded breakfast cereal produced with organic passion fruit fiber and corn flour

The aim of this study was to determine the influence of process parameters and Passion Fruit Fiber (PFF) addition on the Glycemic Index (GI) of an extruded breakfast cereal. A 2³ Central Composite Rotational Design (CCRD) was used, with the following independent variables: raw material moisture content (18-28%), 2nd and 3rd barrel zone temperatures (120-160 ºC), and PFF (0-30%). Raw materials (organic corn flour and organic PFF) were characterized as to their proximate composition, particle size, and in vitro GI. The extrudates were characterized as to their in vitro GI. The Response Surface Methodology (RSM) and Principal Component Analysis (PCA) were used to analyze the results. Corn flour and PFF presented 8.55 and 7.63% protein, 2.61 and 0.60% fat, 0.52 and 6.17% ash, 78.77 and 78.86% carbohydrates (3 and 64% total dietary fiber), respectively. The corn flour particle size distribution was homogeneous, while PFF presented a heterogeneous particle size distribution. Corn flour and PFF presented values of GI of 48 and 45, respectively. When using RSM, no effect of the variables was observed in the GI of the extrudates (average value of 48.41), but PCA showed that the GI tended to be lower when processing at lower temperatures (<128 ºC) and at higher temperatures (>158 ºC). When compared to white bread, the extrudates showed a reduction of the GI of up to 50%, and could be considered an interesting alternative in weight and glycemia control diets.

Deoxynivalenol (DON) degradation and peroxidase enzyme activity in submerged fermentation

This work aims to evaluate deoxynivalenol degradation by Aspergillus oryzae and Rhizopus oryzae in a submerged fermentation system and to correlate it to the activity of oxydo-reductase enzymes. The submerged medium consisted of sterile distilled water contaminated with 50 μg of DON and 4 × 10(6) spore.mL-1 inoculum of Aspergillus oryzae and Rhizopus oryzae species, respectively in each experiment. Sampling was performed every 24 hours for monitoring the peroxidase specific activity, and every 48 hours for determining mycotoxin levels. Results showed that the fungi species were able to decrease DON levels as the peroxidase activity increased. The 48 hours fermentation interval presented the highest peroxidase specific activity (ΔABS/minute.μg.protein-1), 800 and 198, while the highest DON degradation velocity was 10.8 and 12.4 ppb/hour, respectively in both cases for Rhizopus oryzae and Aspergillus oryzae.

Quinoa (Chenopodium quinoa, Willd.) as a source of dietary fiber and other functional components

Four varieties of an Andean indigenous crop, quinoa (Chenopodium quinoa Willd.), were evaluated as a source of dietary fiber, phenolic compounds and antioxidant activity. The crops were processed by extrusion-cooking and the final products were analyzed to determine the dietary fiber, total polyphenols, radical scavenging activity, and in vitro digestibility of starch and protein. There were no significant differences in the contents of total dietary fiber between varieties of quinoa. In all cases, the contents of total and insoluble dietary fiber decreased during the extrusion process. At the same time, the content of soluble dietary fiber increased. The content of total phenolic compounds and the radical scavenging activity increased during the extrusion process in the case of all 4 varieties. There were significant differences between the varieties and the content of total polyphenols. The in vitro protein digestibility of quinoa varieties was between 76.3 and 80.5% and the in vitro starch digestibility was between 65.1 and 68.7%. Our study demonstrates that quinoa can be considered a good source of dietary fiber, polyphenols and other antioxidant compounds and that extrusion improves the nutritional value.

Color degradation kinetics in low-calorie strawberry and guava jellies

The purpose of this study was to follow-up color changes in low-calorie strawberry and guava jellies during storage. To this end, one formulation of each flavor was prepared varying the application of hydrocolloids (pectin and modified starch). The jellies were studied regarding pH, soluble solids, water activity and syneresis. In order to follow-up color changes, the samples remained stored for 180 days in chambers with controlled temperatures of 10 °C (control) and 25 °C (commercial), and color instrumental analyses (L*, a*, and b*) were performed every 30 days. Arrhenius model was applied to reaction speeds (k) at different temperatures, where light strawberry and guava jellies showed greater color changes when stored at 25 °C compared to the samples stored at 10 °C. Activation energy values between 13 and 15 kcal.mol-1 and Q10 values between 2.1 and 2.3 were obtained for light strawberry jelly and light guava jelly, respectively. Therefore, it was concluded that, with respect to color changes, every 10 °C temperature increase reduces light jellies shelf-life by half.

Some functional characteristics of extruded blends of fiber from sugarcane bagasse, whey protein concentrate, and corn starch

Blends of fiber from sugar cane bagasse, corn starch, and whey protein concentrate were extruded. A single screw extruder, equipped with a screw at a constant compression ratio of 1:1 and a die diameter of 3 mm, was used. The best processing conditions were determined according to a central composite rotatable design (α = 1.41) with 5 central points, which gives a total of 13 tests. During the extrusion process the content of insoluble fiber decreased and that of soluble fiber increased. An increase in the contents of fiber and in the barrel temperature resulted in a decrease in the expansion index values and an increase in the water absorption index values; whereas in blends with intermediate fiber contents the effects in these parameters were found to be the opposite. High fiber contents increased penetration force but decreased luminosity, water solubility index values and the adhesive force in gels. The extrusion process improved the functional properties of sugarcane fiber bagasse enabling its addition to diverse alimentary systems.

The use of cashew apple residue as source of fiber in low fat hamburgers

The main purpose of this study was to produce hamburgers with partial substitution of the meat with cashew apple residue powder. The powder residue was obtained after the extraction of the pulp and dehydration in stove with air circulation. Three formulations of hamburgers with increasing concentration of the residue as well as a control sample were prepared. The formulated products with cashew apple residue powder presented lower humidity and proteins and 35% lipid reduction. However, there was an increase in carbohydrates and pH with the addition of the powder from the cashew apple residue. Some formulations showed an improvement of the final product yield. The total dietary fiber value was between 0 and 7.66%, with higher content of insoluble dietary fiber. The addition of up to 10.70% of the residue did not cause significant sensory changes in the flavor of the samples. The production of hamburgers with a partial substitution of cow meat with the cashew apple residue could be a feasible option since it resulted in product with high nutritional quality that is rich or have high dietary fiber content and is low in fat.

Changes in breaded chicken and oil degradation during discontinuous frying with cottonseed oil

Discontinuous frying of breaded chicken in cottonseed oil was evaluated. Three 400 g batches of foodstuff were fried daily in a 28 L fryer at 182 °C for 4.5 minutes for 7-8 days, and the experiment was repeated three times. The total polar compounds in the oil were determined by the conventional method. Changes in the oil were determined by the quick tests Testo 265, Viscofrit and Fri-check based on physical constants, and the results were compared with those of total polar compounds obtained by the conventional method. The free fatty acids, conjugated dienes, Lovibond color, oxidative stability, fatty acid composition, and polymeric compounds were also determined. During frying, the oil samples presented 6.0-39.2% total polar compounds, 0.0-12.9% polymerized triacylglycerols, 1.3-14.5% oxidized triacylglycerols, 2.8-11.0% diacylglycerols, and 1.6-2.6% fatty acids and unsaponifiable polar compounds. The breaded chicken samples lost moisture, absorbed oil up to approximately 6%, and there were small changes in the fatty acid composition and low formation of trans-isomers. The best method for monitoring and discarding the oil was that used for the determination of total polar compounds.

Orange fiber as a novel fat replacer in lemon ice cream

Orange fiber was used as a novel fat replacer in light lemon ice cream. Nine ice cream formulations were compared: standard control ice cream (IC); ice cream with fiber (F1) from the peel, bagasse, and orange seed (ICA and ICB); ice cream with fiber (F2) from the orange peel alone (ICC and ICD); ice cream with fiber (F3) from the peel, bagasse, and orange seed pretreated with hydro-distillation (ICE and ICF); and ice cream with fiber (F4) from the orange peel pretreated with hydro-distillation (ICG and ICH).The orange fiber reduced the ice cream fat content (50 %) and the overrun ratio and increased the fiber content and the hardness, gumminess, and springiness values, but it did not affect the adhesiveness and odor of the samples. The samples with 1.0 % of orange fiber showed low melting rate values than those of the control ice cream. The overall acceptance of the ice cream with 1.0 % of pre-treated orange peel fiber did not differ from that of the control ice cream (80 %). The orange fiber proved a promising food ingredient since it can be used to decrease the fat content and increase bioactive compounds content, such as fiber and carotenoids.

Effect of the addition of wheat fiber and partial pork back fat on the chemical composition, texture and sensory property of low-fat bologna sausage containing inulin and oat fiber

The objective of this work was to study the effect of adding wheat fiber and partial pork back fat on the quality characteristics of bologna sausage. The compound central rotating design was used with treatments containing fixed levels of inulin (5%) and oat fiber (1%) and variable levels of wheat fiber (0-4%) and pork back fat (0-10%). The pH and protein were similar in all the treatments, the fat was lower than the control treatment and the moisture content was higher than the control treatment (CF) without fibers. The wheat fiber increased the hardness and reduced cohesiveness and scores were given for overall impression. We found that it was possible to prepare low-fat bologna sausage with the addition of 6.58% fiber (5% inulin, 1% oat fiber and 0.58% wheat fiber), whilst retaining good sensory acceptability, thus reducing the pork back fat levels by between 25 and 42.75%.

Effects of orange by-product fiber incorporation on the functional and technological properties of pasta

AbstractThe incorporation of fiber into products consumed every day by the general population is important and viable. The aim of the present work was to evaluate the impact of incorporating orange juice industry dietary fiber byproducts in fettuccini of fresh pasta. Three different fiber concentrations were added to fresh pastas (25 g/kg, 50 g/kg and 75 g/kg). The results showed a significant increase in solid loss content when the incorporation of orange fiber was greater than 50 g/kg. This difference did not occur regarding weight increase values and color parameters. The pasta with 75 g/kg orange fiber can be considered a “high fiber” product, with the total dietary fiber content of the pasta increasing by 99% compared to control pasta. The carotenoid and phenolic contents of pasta increased significantly with the incorporation of fiber at 75 g/kg, but only the pasta formulation with 25 g/kg of orange fiber did not differ from control pasta in relation to all of the sensory attributes and presented an acceptance greater than 75%. The addition of orange fiber byproducts to pastas is an interesting alternative because fiber has a high nutritional value and an abundance of antioxidants.

Automated static image analysis as a novel tool in describing the physical properties of dietary fiber

Abstract The growing interest in the usage of dietary fiber in food has caused the need to provide precise tools for describing its physical properties. This research examined two dietary fibers from oats and beets, respectively, in variable particle sizes. The application of automated static image analysis for describing the hydration properties and particle size distribution of dietary fiber was analyzed. Conventional tests for water holding capacity (WHC) were conducted. The particles were measured at two points: dry and after water soaking. The most significant water holding capacity (7.00 g water/g solid) was achieved by the smaller sized oat fiber. Conversely, the water holding capacity was highest (4.20 g water/g solid) in larger sized beet fiber. There was evidence for water absorption increasing with a decrease in particle size in regards to the same fiber source. Very strong correlations were drawn between particle shape parameters, such as fiber length, straightness, width and hydration properties measured conventionally. The regression analysis provided the opportunity to estimate whether the automated static image analysis method could be an efficient tool in describing the hydration properties of dietary fiber. The application of the method was validated using mathematical model which was verified in comparison to conventional WHC measurement results.

Effect of dietary fiber on the bioaccessibility of phenolic compounds of mango, papaya and pineapple fruits by an in vitro digestion model

The presence of dietary fiber (DF) in the food matrix of some tropical fruits plays an important role in the release and absorption of its bioactive compounds, such as phenolic compounds (PCs). The aim of this study was to evaluate the effect of the DF fractions in mango cv. ‘Ataulfo’, papaya cv. ‘Maradol’ and pineapple cv. ‘Esmeralda’, on the bioaccessibility of their PCs and antioxidant capacity (AOXC) under an in vitro digestion model. The highest PCs content and AOXC was found in mango (274.30 mg GAE/100 g FW), followed by papaya (212 mg GAE//100 g FW), and pineapple (107.63 mg GAE/100 g FW), respectively. About 50% of the total PCs in all fruits was released at gastric phase, increasing closer to 60% at intestinal phase in mango and pineapple. However, the highest content of PCs associated to DF was found in mango (2.48 mg GAE/100 g FW) compared with papaya DF fractions (0.96 GAE/100 g FW) and pineapple (0.52 GAE/100 g FW). The presence of DF in mango, papaya and pineapple did not represent a major limitation on the bioaccessibility of its PCs according to the in vitro digestion model used in this study.

Survey of trace element and dietetic fiber composition of “Leblebi” which is a local snack food consumed in Turkey

Abstract In Turkey and several Middle East countries' people consume “leblebi” which is a traditional snack food made from chickpeas (Cicer arietinum L.). Chickpea products are highly nutritive and a cheap food for human consumption and have become an essential part of daily diets in the world. The present study aims to determine the chemical, nutritional and dietary composition of fifty leblebi samples marketed in Turkey. Protein values of the leblebi ranged from 19.4 to 23.9% dehulled and 20.3 to 20.8% for nondehulled leblebi while a value of 19.1% was recorded for chickpeas. Mineral results showed that Potassium (K) was the most abundant element in leblebi ranging from 6514 to 14431 mg/kg. The amount of dietary components neutral detergent fibre (NDF), acid detergent fibre (ADF), acid detergent lignin (ADL) and cellulose did not vary much between the samples analyzed.